350 lines
11 KiB
C
350 lines
11 KiB
C
/*
|
||
* 配置相关
|
||
*/
|
||
|
||
/* Includes ----------------------------------------------------------------- */
|
||
#include "module/config.h"
|
||
#include <stdbool.h>
|
||
|
||
|
||
/* Private typedef ---------------------------------------------------------- */
|
||
/* Private define ----------------------------------------------------------- */
|
||
/* Private macro ------------------------------------------------------------ */
|
||
/* Private variables -------------------------------------------------------- */
|
||
|
||
/* Exported variables ------------------------------------------------------- */
|
||
|
||
/**
|
||
* @brief 机器人参数配置
|
||
* @note 在此配置机器人参数
|
||
*/
|
||
Config_RobotParam_t robot_config = {
|
||
/* USER CODE BEGIN robot_config */
|
||
|
||
.gimbal_param = {
|
||
.pid = {
|
||
.yaw_omega = {
|
||
.k = 2.0f,
|
||
.p = 1.0f,
|
||
.i = 0.3f,
|
||
.d = 0.0f,
|
||
.i_limit = 1.0f,
|
||
.out_limit = 1.0f,
|
||
.d_cutoff_freq = -1.0f,
|
||
.range = -1.0f,
|
||
},
|
||
.yaw_angle = {
|
||
.k = 7.0f,
|
||
.p = 3.5f,
|
||
.i = 0.0f,
|
||
.d = 0.0f,
|
||
.i_limit = 0.0f,
|
||
.out_limit = 10.0f,
|
||
.d_cutoff_freq = -1.0f,
|
||
.range = M_2PI,
|
||
},
|
||
.pit_omega = {
|
||
.k = 0.25f,
|
||
.p = 1.0f,
|
||
.i = 0.0f,
|
||
.d = 0.0f,
|
||
.i_limit = 1.0f,
|
||
.out_limit = 1.0f,
|
||
.d_cutoff_freq = -1.0f,
|
||
.range = -1.0f,
|
||
},
|
||
.pit_angle = {
|
||
.k = 2.5f,
|
||
.p = 5.0f,
|
||
.i = 0.2f,
|
||
.d = 0.01f,
|
||
.i_limit = 0.0f,
|
||
.out_limit = 10.0f,
|
||
.d_cutoff_freq = -1.0f,
|
||
.range = M_2PI,
|
||
},
|
||
},
|
||
.mech_zero = {
|
||
.yaw = 0.0f,
|
||
.pit = 2.2f,
|
||
},
|
||
.travel = {
|
||
.yaw = -1.0f,
|
||
.pit = 0.85f,
|
||
},
|
||
.low_pass_cutoff_freq = {
|
||
.out = -1.0f,
|
||
.gyro = 1000.0f,
|
||
},
|
||
.pit_motor ={
|
||
.can = BSP_CAN_1,
|
||
.id = 0x206,
|
||
.gear = false,
|
||
.module = MOTOR_GM6020,
|
||
.reverse = true,
|
||
},
|
||
.yaw_motor = {
|
||
.can = BSP_CAN_1,
|
||
.can_id = 0x1,
|
||
.master_id = 0x11,
|
||
.module = MOTOR_DM_J4310,
|
||
.reverse = false,
|
||
},
|
||
.imu = {
|
||
.can = BSP_CAN_2,
|
||
.accl_id = 0x100, // 加速度计 (十进制256)
|
||
.gyro_id = 0x101, // 陀螺仪 (十进制257)
|
||
.eulr_id = 0x102, // 欧拉角 (十进制258)
|
||
.quat_id = 0x103 // 四元数 (十进制259)
|
||
},
|
||
|
||
},
|
||
|
||
|
||
|
||
.shoot_param = {
|
||
.trig_step_angle=M_2PI/8,
|
||
.shot_delay_time=1.0f,
|
||
.shot_burst_num=20,
|
||
.fric_motor_param[0] = {
|
||
.can = BSP_CAN_1,
|
||
.id = 0x201,
|
||
.module = MOTOR_M3508,
|
||
.reverse = false,
|
||
.gear=false,
|
||
},
|
||
.fric_motor_param[1] = {
|
||
.can = BSP_CAN_1,
|
||
.id = 0x202,
|
||
.module = MOTOR_M3508,
|
||
.reverse = true,
|
||
.gear=false,
|
||
},
|
||
.trig_motor_param = {
|
||
.can = BSP_CAN_1,
|
||
.id = 0x203,
|
||
.module = MOTOR_M2006,
|
||
.reverse = true,
|
||
.gear=true,
|
||
},
|
||
.fric_follow = {
|
||
.k=1.0f,
|
||
.p=1.5f,
|
||
.i=0.0f,
|
||
.d=0.0f,
|
||
.i_limit=0.0f,
|
||
.out_limit=0.9f,
|
||
.d_cutoff_freq=30.0f,
|
||
.range=-1.0f,
|
||
},
|
||
|
||
.fric_err = {
|
||
.k=1.0f,
|
||
.p=4.0f,
|
||
.i=0.4f,
|
||
.d=0.04f,
|
||
.i_limit=0.25f,
|
||
.out_limit=0.25f,
|
||
.d_cutoff_freq=40.0f,
|
||
.range=-1.0f,
|
||
},
|
||
.trig_omg = {
|
||
.k=1.0f,
|
||
.p=1.5f,
|
||
.i=0.3f,
|
||
.d=0.5f,
|
||
.i_limit=0.2f,
|
||
.out_limit=0.9f,
|
||
.d_cutoff_freq=-1.0f,
|
||
.range=-1.0f,
|
||
},
|
||
.trig = {
|
||
.k=1.0f,
|
||
.p=1.0f,
|
||
.i=0.1f,
|
||
.d=0.05f,
|
||
.i_limit=0.8f,
|
||
.out_limit=0.5f,
|
||
.d_cutoff_freq=-1.0f,
|
||
.range=M_2PI,
|
||
},
|
||
.filter.fric = {
|
||
.in = 30.0f,
|
||
.out = 30.0f,
|
||
},
|
||
.filter.trig = {
|
||
.in = 30.0f,
|
||
.out = 30.0f,
|
||
},
|
||
},
|
||
|
||
.chassis_param = {
|
||
.yaw={
|
||
.k=1.0f,
|
||
.p=1.0f,
|
||
.i=0.0f,
|
||
.d=0.3f,
|
||
.i_limit=0.0f,
|
||
.out_limit=1.0f,
|
||
.d_cutoff_freq=30.0f,
|
||
.range=M_2PI, /* 2*PI，用于处理角度循环误差 */
|
||
},
|
||
|
||
.roll={
|
||
.k=0.2f,
|
||
.p=0.5f, /* 横滚角比例系数 */
|
||
.i=0.01f, /* 横滚角积分系数 */
|
||
.d=0.01f, /* 横滚角微分系数 */
|
||
.i_limit=0.2f, /* 积分限幅 */
|
||
.out_limit=1.0f, /* 输出限幅，腿长差值限制 */
|
||
.d_cutoff_freq=30.0f, /* 微分截止频率 */
|
||
.range=-1.0f, /* 不使用循环误差处理 */
|
||
},
|
||
|
||
.leg_length={
|
||
.k = 40.0f,
|
||
.p = 20.0f,
|
||
.i = 0.01f,
|
||
.d = 2.0f,
|
||
.i_limit = 0.0f,
|
||
.out_limit = 200.0f,
|
||
.d_cutoff_freq = -1.0f,
|
||
.range = -1.0f,
|
||
},
|
||
|
||
.leg_theta={
|
||
.k=5.0f,
|
||
.p=2.0f, /* 摆角比例系数 */
|
||
.i=0.0f, /* 摆角积分系数 */
|
||
.d=0.0f, /* 摆角微分系数 */
|
||
.i_limit=0.0f, /* 积分限幅 */
|
||
.out_limit=0.05f, /* 输出限幅，腿长差值限制 */
|
||
.d_cutoff_freq=30.0f, /* 微分截止频率 */
|
||
.range=-1.0f, /* 不使用循环误差处理 */
|
||
},
|
||
|
||
.tp={
|
||
.k=4.0f,
|
||
.p=3.0f, /* 俯仰角比例系数 */
|
||
.i=0.0f, /* 俯仰角积分系数 */
|
||
.d=0.0f, /* 俯仰角微分系数 */
|
||
.i_limit=0.0f, /* 积分限幅 */
|
||
.out_limit=10.0f, /* 输出限幅，腿长差值限制 */
|
||
.d_cutoff_freq=30.0f, /* 微分截止频率 */
|
||
.range=-1.0f, /* 不使用循环误差处理 */
|
||
},
|
||
|
||
.low_pass_cutoff_freq = {
|
||
.in = 30.0f,
|
||
.out = 30.0f,
|
||
},
|
||
|
||
.yaw_motor = { // 云台Yaw轴电机
|
||
.can = BSP_CAN_1,
|
||
.can_id = 0x1,
|
||
.master_id = 0x11,
|
||
.module = MOTOR_DM_J4310,
|
||
.reverse = false,
|
||
},
|
||
|
||
.joint_param = {
|
||
{ // 左髋关节
|
||
.can = BSP_CAN_3,
|
||
.motor_id = 124,
|
||
.host_id = 0xFF,
|
||
.module = MOTOR_LZ_RSO3,
|
||
.reverse = false,
|
||
.mode = MOTOR_LZ_MODE_MOTION,
|
||
},
|
||
{ // 右髋关节
|
||
.can = BSP_CAN_3,
|
||
.motor_id = 125,
|
||
.host_id = 0xFF,
|
||
.module = MOTOR_LZ_RSO3,
|
||
.reverse = false,
|
||
.mode = MOTOR_LZ_MODE_MOTION,
|
||
},
|
||
{ // 左膝关节
|
||
.can = BSP_CAN_3,
|
||
.motor_id = 126,
|
||
.host_id = 0xFF,
|
||
.module = MOTOR_LZ_RSO3,
|
||
.reverse = true,
|
||
.mode = MOTOR_LZ_MODE_MOTION,
|
||
},
|
||
{ // 右膝关节
|
||
.can = BSP_CAN_3,
|
||
.motor_id = 127,
|
||
.host_id = 0xFF,
|
||
.module = MOTOR_LZ_RSO3,
|
||
.reverse = true,
|
||
.mode = MOTOR_LZ_MODE_MOTION,
|
||
},
|
||
},
|
||
|
||
.wheel_param = {
|
||
{ // 左轮电机
|
||
.can = BSP_CAN_3,
|
||
.id = 0x142,
|
||
.module = MOTOR_LK_MF9025,
|
||
.reverse = false,
|
||
},
|
||
{ // 右轮电机
|
||
.can = BSP_CAN_3,
|
||
.id = 0x141,
|
||
.module = MOTOR_LK_MF9025,
|
||
.reverse = true,
|
||
},
|
||
},
|
||
|
||
.mech_zero_yaw = 1.78040409f, /* 机械零点 */
|
||
|
||
.vmc_param = {
|
||
{ // 左腿
|
||
.leg_1 = 0.215f, // 后髋连杆长度 (L1) (m)
|
||
.leg_2 = 0.258f, // 后膝连杆长度 (L2) (m)
|
||
.leg_3 = 0.258f, // 前膝连杆长度 (L3) (m)
|
||
.leg_4 = 0.215f, // 前髋连杆长度 (L4) (m)
|
||
.hip_length = 0.0f // 髋宽 (L5) (m)
|
||
},
|
||
{ // 右腿
|
||
.leg_1 = 0.215f, // 后髋连杆长度 (L1) (m)
|
||
.leg_2 = 0.258f, // 后膝连杆长度 (L2) (m)
|
||
.leg_3 = 0.258f, // 前膝连杆长度 (L3) (m)
|
||
.leg_4 = 0.215f, // 前髋连杆长度 (L4) (m)
|
||
.hip_length = 0.0f // 髋宽 (L5) (m)
|
||
}
|
||
},
|
||
|
||
.lqr_gains = {
|
||
.k11_coeff = { -2.120324305163214e+02f, 2.384281822810979e+02f, -1.162210131498081e+02f, -2.405740963481636e+00f }, // theta
|
||
.k12_coeff = { 4.320836680770054e-01f, 1.360781729068518e-01f, -8.343612068216379e+00f, -8.600090910123033e-02f }, // d_theta
|
||
.k13_coeff = { -4.493046202256553e+01f, 4.577344792125822e+01f, -1.629835599958664e+01f, -1.007247166173255e+00f }, // x
|
||
.k14_coeff = { -4.823335755850488e+01f, 4.987409533322209e+01f, -1.917162943665977e+01f, -1.473642463713354e+00f }, // d_x
|
||
.k15_coeff = { -4.920796990864941e+01f, 6.450325939254844e+01f, -3.268284723443183e+01f, 7.841340265493823e+00f }, // phi
|
||
.k16_coeff = { -1.264530042590822e+01f, 1.663296191858249e+01f, -8.467446023207946e+00f, 2.096442008644146e+00f }, // d_phi
|
||
.k21_coeff = { 1.636475235954215e+02f, -1.128937920212271e+02f, 4.887401528348596e+00f, 1.459120525493287e+01f }, // theta
|
||
.k22_coeff = { 9.939826270288583e+00f, -8.353709902293666e+00f, 1.640639416293288e+00f, 1.492185865897709e+00f }, // d_theta
|
||
.k23_coeff = { -4.968599085108445e+01f, 6.646556717472484e+01f, -3.397333983104631e+01f, 7.847958130301292e+00f }, // x
|
||
.k24_coeff = { -7.188031995054928e+01f, 9.082377283123918e+01f, -4.412648091833633e+01f, 9.959213854333724e+00f }, // d_x
|
||
.k25_coeff = { 2.360507220981238e+02f, -2.398095392324340e+02f, 8.536061841837561e+01f, 2.469595316477948e+00f }, // phi
|
||
.k26_coeff = { 6.296425580760564e+01f, -6.412220242164098e+01f, 2.293354052056732e+01f, 4.870876539985159e-01f }, // d_phi
|
||
},
|
||
.theta = 0.0f,
|
||
.x = 0.0f,
|
||
.phi = -0.1f,
|
||
|
||
}
|
||
/* USER CODE END robot_config */
|
||
};
|
||
|
||
/* Private function prototypes ---------------------------------------------- */
|
||
/* Exported functions ------------------------------------------------------- */
|
||
|
||
/**
|
||
* @brief 获取机器人配置参数
|
||
* @return 机器人配置参数指针
|
||
*/
|
||
Config_RobotParam_t* Config_GetRobotParam(void) {
|
||
return &robot_config;
|
||
} |