/*
 * 配置相关
 */

/* Includes ----------------------------------------------------------------- */
#include "module/config.h"
#include "bsp/can.h"
#include "device/motor_dm.h"


/* Private typedef ---------------------------------------------------------- */
/* Private define ----------------------------------------------------------- */
/* Private macro ------------------------------------------------------------ */
/* Private variables -------------------------------------------------------- */

/* Exported variables ------------------------------------------------------- */

// 机器人参数配置
Config_RobotParam_t robot_config = {

    .imu_param = {
        .can = BSP_CAN_2,
        .can_id = 0x6FF,      
        .device_id = 0x42,   
        .master_id = 0x43,   
    },

    .chassis_param = {
        .yaw={
            .k=1.0f,
            .p=1.2f,
            .i=0.0f,
            .d=0.05f,
            .i_limit=0.0f,
            .out_limit=1.0f,
            .d_cutoff_freq=30.0f,
            .range=M_2PI, /* 2*PI，用于处理角度循环误差 */
        },

        .roll={
            .k=10.0f,
            .p=5.0f,           /* 横滚角比例系数 */
            .i=0.0f,           /* 横滚角积分系数 */
            .d=0.2f,           /* 横滚角微分系数 */
            .i_limit=0.0f,     /* 积分限幅 */
            .out_limit=50.0f,  /* 输出限幅，腿长差值限制 */
            .d_cutoff_freq=30.0f, /* 微分截止频率 */
            .range=-1.0f,      /* 不使用循环误差处理 */
        },

        .leg_length={
            .k = 20.0f,
            .p = 5.0f,
            .i = 0.0f,
            .d = 1.0f,
            .i_limit = 0.0f,
            .out_limit = 100.0f,
            .d_cutoff_freq = -1.0f,
            .range = -1.0f,
        },
        .leg_theta={
            .k=1.0f,
            .p=5.0f,           /* 摆角比例系数 */
            .i=0.0f,           /* 摆角积分系数 */
            .d=0.0f,           /* 摆角微分系数 */
            .i_limit=0.0f,     /* 积分限幅 */
            .out_limit=0.05f,  /* 输出限幅，腿长差值限制 */
            .d_cutoff_freq=30.0f, /* 微分截止频率 */
            .range=-1.0f,      /* 不使用循环误差处理 */
        },

        .tp={
            .k=1.0f,
            .p=2.0f,          /* 俯仰角比例系数 */
            .i=0.0f,           /* 俯仰角积分系数 */
            .d=0.0f,           /* 俯仰角微分系数 */
            .i_limit=0.0f,     /* 积分限幅 */
            .out_limit=2.0f,   /* 输出限幅，腿长差值限制 */
            .d_cutoff_freq=30.0f, /* 微分截止频率 */
            .range=-1.0f,      /* 不使用循环误差处理 */
        },
        

        .low_pass_cutoff_freq = {
            .in = 30.0f,
            .out = 30.0f,
        },

        .yaw_motor = { // 云台Yaw轴电机
            .can = BSP_CAN_2,
            .can_id = 0x1,
            .master_id = 0x11,
            .module = MOTOR_DM_J4310,
            .reverse = false,
        },

        .mech_zero_yaw = 4.34085676f, /* 250.5度，机械零点 */
        
        .vmc_param = {
            { // 左腿
                .leg_1 = 0.215f,      // 后髋连杆长度 (L1) (m)
                .leg_2 = 0.258f,      // 后膝连杆长度 (L2) (m)
                .leg_3 = 0.258f,      // 前膝连杆长度 (L3) (m)
                .leg_4 = 0.215f,      // 前髋连杆长度 (L4) (m)
                .hip_length = 0.0f    // 髋宽 (L5) (m)
            },
            { // 右腿
                .leg_1 = 0.215f,      // 后髋连杆长度 (L1) (m)
                .leg_2 = 0.258f,      // 后膝连杆长度 (L2) (m)
                .leg_3 = 0.258f,      // 前膝连杆长度 (L3) (m)
                .leg_4 = 0.215f,      // 前髋连杆长度 (L4) (m)
                .hip_length = 0.0f    // 髋宽 (L5) (m)
            }
        },
        .lqr_gains = {
            .k11_coeff = { -1.916376919295156e+02f, 2.009487240966917e+02f, -9.481460086781939e+01f, -4.748704486775178e+00f }, // theta
            .k12_coeff = { -1.794538872095484e+00f, -1.557720009681701e-02f, -7.253705624763870e+00f, -9.066344876912042e-01f },  // d_theta
            .k13_coeff = { -5.530128764310525e+01f, 5.441066051951745e+01f, -1.855725101721958e+01f, -1.532320658646968e+00f },  // x
            .k14_coeff = { -5.226956984912729e+01f, 5.134367619659140e+01f, -1.878250555345751e+01f, -2.194040977657715e+00f },  // d_x
            .k15_coeff = { -8.041587662748894e+00f, 1.194985309170939e+01f, -6.358536570979702e+00f, 8.475914154881636e-01f }, // phi
            .k16_coeff = { -1.171602430557222e+01f, 1.424681188601595e+01f, -6.769563511869035e+00f, 1.358696951640962e+00f },  // d_phi
            .k21_coeff = { -1.589916277171124e+01f, 3.688717311486668e+01f, -2.693106123880470e+01f, 8.468880380216705e+00f }, // theta
            .k22_coeff = { -4.056650578339882e+00f, 5.627051302682392e+00f, -2.802037254431724e+00f, 1.258712322539219e+00f },  // d_theta
            .k23_coeff = { -4.615940205649521e+01f, 5.298830026615487e+01f, -2.321905486010759e+01f, 4.733000143959848e+00f },  // x
            .k24_coeff = { -6.198443605956307e+01f, 6.867018097135634e+01f, -2.873375258895661e+01f, 5.632056979434964e+00f },  // d_x
            .k25_coeff = { -1.149934231218892e+01f, 9.960303123832579e+00f, -2.826210920406189e+00f, 4.384038656352771e+00f }, // phi
            .k26_coeff = { 1.452344963148120e+01f, -1.451377402367933e+01f, 5.020766559053281e+00f, 1.099371055071753e+00f },  // d_phi
        },
        .virtual_chassis_param = {
            .motors = {
                    .can = BSP_CAN_1,
                    .enable_id = 121,
                    .joint_cmd_id = 122,
                    .joint_feedback_base_id = 124,
                    .wheel_left_id = 0x128,
                    .wheel_right_id = 0x129,
                    .wheel_left_feedback_id = 0x82,
                    .wheel_right_feedback_id = 0x83,
            },
            .imu = {
                    .can = BSP_CAN_1,
                    .accl_id = 0x301,
                    .gyro_id = 0x302,
                    .euler_id = 0x303,   
                    .quat_id = 0x304,
            },
        },
    },


};

/* Private function prototypes ---------------------------------------------- */
/* Exported functions ------------------------------------------------------- */

/**
 * @brief 获取机器人配置参数
 * @return 机器人配置参数指针
 */
Config_RobotParam_t* Config_GetRobotParam(void) {
    return &robot_config;
}