Atmel AT91SAM9G20 SAM9G 20130207 Atmel AT91SAM9G20 device: ARM926EJ Embedded Microprocessor Unit, 400MHz, USB, Ethernet, 217 and 247 Pins (refer to http://www.atmel.com/devices/SAM9G20.aspx for more) 8 32 UHP 6127F USB Host Port 0x00500000 0 0x100000 registers UHP 20 TC0 6082L Timer Counter 0 TC TC0_ 0xFFFA0000 0 0x4000 registers TC0 17 TC1 18 TC2 19 CCR0 Channel Control Register (channel = 0) 0x00000000 32 write-only CLKEN Counter Clock Enable Command 0 1 write-only CLKDIS Counter Clock Disable Command 1 1 write-only SWTRG Software Trigger Command 2 1 write-only CMR0 Channel Mode Register (channel = 0) 0x00000004 32 read-write 0x00000000 TCCLKS Clock Selection 0 3 read-write TIMER_CLOCK1 Clock selected: TCLK1 0x0 TIMER_CLOCK2 Clock selected: TCLK2 0x1 TIMER_CLOCK3 Clock selected: TCLK3 0x2 TIMER_CLOCK4 Clock selected: TCLK4 0x3 TIMER_CLOCK5 Clock selected: TCLK5 0x4 XC0 Clock selected: XC0 0x5 XC1 Clock selected: XC1 0x6 XC2 Clock selected: XC2 0x7 CLKI Clock Invert 3 1 read-write BURST Burst Signal Selection 4 2 read-write NONE The clock is not gated by an external signal. 0x0 XC0 XC0 is ANDed with the selected clock. 0x1 XC1 XC1 is ANDed with the selected clock. 0x2 XC2 XC2 is ANDed with the selected clock. 0x3 LDBSTOP Counter Clock Stopped with RB Loading 6 1 read-write LDBDIS Counter Clock Disable with RB Loading 7 1 read-write ETRGEDG External Trigger Edge Selection 8 2 read-write NONE The clock is not gated by an external signal. 0x0 RISING Rising edge 0x1 FALLING Falling edge 0x2 EDGE Each edge 0x3 ABETRG TIOA or TIOB External Trigger Selection 10 1 read-write CPCTRG RC Compare Trigger Enable 14 1 read-write WAVE 15 1 read-write LDRA RA Loading Selection 16 2 read-write NONE None 0x0 RISING Rising edge of TIOA 0x1 FALLING Falling edge of TIOA 0x2 EDGE Each edge of TIOA 0x3 LDRB RB Loading Selection 18 2 read-write NONE None 0x0 RISING Rising edge of TIOA 0x1 FALLING Falling edge of TIOA 0x2 EDGE Each edge of TIOA 0x3 CMR0_WAVE_EQ_1 Channel Mode Register (channel = 0) WAVE_EQ_1 0x00000004 32 read-write 0x00000000 TCCLKS Clock Selection 0 3 read-write TIMER_CLOCK1 Clock selected: TCLK1 0x0 TIMER_CLOCK2 Clock selected: TCLK2 0x1 TIMER_CLOCK3 Clock selected: TCLK3 0x2 TIMER_CLOCK4 Clock selected: TCLK4 0x3 TIMER_CLOCK5 Clock selected: TCLK5 0x4 XC0 Clock selected: XC0 0x5 XC1 Clock selected: XC1 0x6 XC2 Clock selected: XC2 0x7 CLKI Clock Invert 3 1 read-write BURST Burst Signal Selection 4 2 read-write NONE The clock is not gated by an external signal. 0x0 XC0 XC0 is ANDed with the selected clock. 0x1 XC1 XC1 is ANDed with the selected clock. 0x2 XC2 XC2 is ANDed with the selected clock. 0x3 CPCSTOP Counter Clock Stopped with RC Compare 6 1 read-write CPCDIS Counter Clock Disable with RC Compare 7 1 read-write EEVTEDG External Event Edge Selection 8 2 read-write NONE None 0x0 RISING Rising edge 0x1 FALLING Falling edge 0x2 EDGE Each edge 0x3 EEVT External Event Selection 10 2 read-write TIOB TIOB 0x0 XC0 XC0 0x1 XC1 XC1 0x2 XC2 XC2 0x3 ENETRG External Event Trigger Enable 12 1 read-write WAVSEL Waveform Selection 13 2 read-write UP UP mode without automatic trigger on RC Compare 0x0 UPDOWN UPDOWN mode without automatic trigger on RC Compare 0x1 UP_RC UP mode with automatic trigger on RC Compare 0x2 UPDOWN_RC UPDOWN mode with automatic trigger on RC Compare 0x3 WAVE 15 1 read-write ACPA RA Compare Effect on TIOA 16 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 ACPC RC Compare Effect on TIOA 18 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 AEEVT External Event Effect on TIOA 20 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 ASWTRG Software Trigger Effect on TIOA 22 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BCPB RB Compare Effect on TIOB 24 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BCPC RC Compare Effect on TIOB 26 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BEEVT External Event Effect on TIOB 28 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BSWTRG Software Trigger Effect on TIOB 30 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 CV0 Counter Value (channel = 0) 0x00000010 32 read-only 0x00000000 CV Counter Value 0 16 read-only RA0 Register A (channel = 0) 0x00000014 32 read-write 0x00000000 RA Register A 0 16 read-write RB0 Register B (channel = 0) 0x00000018 32 read-write 0x00000000 RB Register B 0 16 read-write RC0 Register C (channel = 0) 0x0000001C 32 read-write 0x00000000 RC Register C 0 16 read-write SR0 Status Register (channel = 0) 0x00000020 32 read-only 0x00000000 COVFS Counter Overflow Status 0 1 read-only LOVRS Load Overrun Status 1 1 read-only CPAS RA Compare Status 2 1 read-only CPBS RB Compare Status 3 1 read-only CPCS RC Compare Status 4 1 read-only LDRAS RA Loading Status 5 1 read-only LDRBS RB Loading Status 6 1 read-only ETRGS External Trigger Status 7 1 read-only CLKSTA Clock Enabling Status 16 1 read-only MTIOA TIOA Mirror 17 1 read-only MTIOB TIOB Mirror 18 1 read-only IER0 Interrupt Enable Register (channel = 0) 0x00000024 32 write-only COVFS Counter Overflow 0 1 write-only LOVRS Load Overrun 1 1 write-only CPAS RA Compare 2 1 write-only CPBS RB Compare 3 1 write-only CPCS RC Compare 4 1 write-only LDRAS RA Loading 5 1 write-only LDRBS RB Loading 6 1 write-only ETRGS External Trigger 7 1 write-only IDR0 Interrupt Disable Register (channel = 0) 0x00000028 32 write-only COVFS Counter Overflow 0 1 write-only LOVRS Load Overrun 1 1 write-only CPAS RA Compare 2 1 write-only CPBS RB Compare 3 1 write-only CPCS RC Compare 4 1 write-only LDRAS RA Loading 5 1 write-only LDRBS RB Loading 6 1 write-only ETRGS External Trigger 7 1 write-only IMR0 Interrupt Mask Register (channel = 0) 0x0000002C 32 read-only 0x00000000 COVFS Counter Overflow 0 1 read-only LOVRS Load Overrun 1 1 read-only CPAS RA Compare 2 1 read-only CPBS RB Compare 3 1 read-only CPCS RC Compare 4 1 read-only LDRAS RA Loading 5 1 read-only LDRBS RB Loading 6 1 read-only ETRGS External Trigger 7 1 read-only CCR1 Channel Control Register (channel = 1) 0x00000040 32 write-only CLKEN Counter Clock Enable Command 0 1 write-only CLKDIS Counter Clock Disable Command 1 1 write-only SWTRG Software Trigger Command 2 1 write-only CMR1 Channel Mode Register (channel = 1) 0x00000044 32 read-write 0x00000000 TCCLKS Clock Selection 0 3 read-write TIMER_CLOCK1 Clock selected: TCLK1 0x0 TIMER_CLOCK2 Clock selected: TCLK2 0x1 TIMER_CLOCK3 Clock selected: TCLK3 0x2 TIMER_CLOCK4 Clock selected: TCLK4 0x3 TIMER_CLOCK5 Clock selected: TCLK5 0x4 XC0 Clock selected: XC0 0x5 XC1 Clock selected: XC1 0x6 XC2 Clock selected: XC2 0x7 CLKI Clock Invert 3 1 read-write BURST Burst Signal Selection 4 2 read-write NONE The clock is not gated by an external signal. 0x0 XC0 XC0 is ANDed with the selected clock. 0x1 XC1 XC1 is ANDed with the selected clock. 0x2 XC2 XC2 is ANDed with the selected clock. 0x3 LDBSTOP Counter Clock Stopped with RB Loading 6 1 read-write LDBDIS Counter Clock Disable with RB Loading 7 1 read-write ETRGEDG External Trigger Edge Selection 8 2 read-write NONE The clock is not gated by an external signal. 0x0 RISING Rising edge 0x1 FALLING Falling edge 0x2 EDGE Each edge 0x3 ABETRG TIOA or TIOB External Trigger Selection 10 1 read-write CPCTRG RC Compare Trigger Enable 14 1 read-write WAVE 15 1 read-write LDRA RA Loading Selection 16 2 read-write NONE None 0x0 RISING Rising edge of TIOA 0x1 FALLING Falling edge of TIOA 0x2 EDGE Each edge of TIOA 0x3 LDRB RB Loading Selection 18 2 read-write NONE None 0x0 RISING Rising edge of TIOA 0x1 FALLING Falling edge of TIOA 0x2 EDGE Each edge of TIOA 0x3 CMR1_WAVE_EQ_1 Channel Mode Register (channel = 1) WAVE_EQ_1 0x00000044 32 read-write 0x00000000 TCCLKS Clock Selection 0 3 read-write TIMER_CLOCK1 Clock selected: TCLK1 0x0 TIMER_CLOCK2 Clock selected: TCLK2 0x1 TIMER_CLOCK3 Clock selected: TCLK3 0x2 TIMER_CLOCK4 Clock selected: TCLK4 0x3 TIMER_CLOCK5 Clock selected: TCLK5 0x4 XC0 Clock selected: XC0 0x5 XC1 Clock selected: XC1 0x6 XC2 Clock selected: XC2 0x7 CLKI Clock Invert 3 1 read-write BURST Burst Signal Selection 4 2 read-write NONE The clock is not gated by an external signal. 0x0 XC0 XC0 is ANDed with the selected clock. 0x1 XC1 XC1 is ANDed with the selected clock. 0x2 XC2 XC2 is ANDed with the selected clock. 0x3 CPCSTOP Counter Clock Stopped with RC Compare 6 1 read-write CPCDIS Counter Clock Disable with RC Compare 7 1 read-write EEVTEDG External Event Edge Selection 8 2 read-write NONE None 0x0 RISING Rising edge 0x1 FALLING Falling edge 0x2 EDGE Each edge 0x3 EEVT External Event Selection 10 2 read-write TIOB TIOB 0x0 XC0 XC0 0x1 XC1 XC1 0x2 XC2 XC2 0x3 ENETRG External Event Trigger Enable 12 1 read-write WAVSEL Waveform Selection 13 2 read-write UP UP mode without automatic trigger on RC Compare 0x0 UPDOWN UPDOWN mode without automatic trigger on RC Compare 0x1 UP_RC UP mode with automatic trigger on RC Compare 0x2 UPDOWN_RC UPDOWN mode with automatic trigger on RC Compare 0x3 WAVE 15 1 read-write ACPA RA Compare Effect on TIOA 16 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 ACPC RC Compare Effect on TIOA 18 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 AEEVT External Event Effect on TIOA 20 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 ASWTRG Software Trigger Effect on TIOA 22 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BCPB RB Compare Effect on TIOB 24 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BCPC RC Compare Effect on TIOB 26 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BEEVT External Event Effect on TIOB 28 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BSWTRG Software Trigger Effect on TIOB 30 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 CV1 Counter Value (channel = 1) 0x00000050 32 read-only 0x00000000 CV Counter Value 0 16 read-only RA1 Register A (channel = 1) 0x00000054 32 read-write 0x00000000 RA Register A 0 16 read-write RB1 Register B (channel = 1) 0x00000058 32 read-write 0x00000000 RB Register B 0 16 read-write RC1 Register C (channel = 1) 0x0000005C 32 read-write 0x00000000 RC Register C 0 16 read-write SR1 Status Register (channel = 1) 0x00000060 32 read-only 0x00000000 COVFS Counter Overflow Status 0 1 read-only LOVRS Load Overrun Status 1 1 read-only CPAS RA Compare Status 2 1 read-only CPBS RB Compare Status 3 1 read-only CPCS RC Compare Status 4 1 read-only LDRAS RA Loading Status 5 1 read-only LDRBS RB Loading Status 6 1 read-only ETRGS External Trigger Status 7 1 read-only CLKSTA Clock Enabling Status 16 1 read-only MTIOA TIOA Mirror 17 1 read-only MTIOB TIOB Mirror 18 1 read-only IER1 Interrupt Enable Register (channel = 1) 0x00000064 32 write-only COVFS Counter Overflow 0 1 write-only LOVRS Load Overrun 1 1 write-only CPAS RA Compare 2 1 write-only CPBS RB Compare 3 1 write-only CPCS RC Compare 4 1 write-only LDRAS RA Loading 5 1 write-only LDRBS RB Loading 6 1 write-only ETRGS External Trigger 7 1 write-only IDR1 Interrupt Disable Register (channel = 1) 0x00000068 32 write-only COVFS Counter Overflow 0 1 write-only LOVRS Load Overrun 1 1 write-only CPAS RA Compare 2 1 write-only CPBS RB Compare 3 1 write-only CPCS RC Compare 4 1 write-only LDRAS RA Loading 5 1 write-only LDRBS RB Loading 6 1 write-only ETRGS External Trigger 7 1 write-only IMR1 Interrupt Mask Register (channel = 1) 0x0000006C 32 read-only 0x00000000 COVFS Counter Overflow 0 1 read-only LOVRS Load Overrun 1 1 read-only CPAS RA Compare 2 1 read-only CPBS RB Compare 3 1 read-only CPCS RC Compare 4 1 read-only LDRAS RA Loading 5 1 read-only LDRBS RB Loading 6 1 read-only ETRGS External Trigger 7 1 read-only CCR2 Channel Control Register (channel = 2) 0x00000080 32 write-only CLKEN Counter Clock Enable Command 0 1 write-only CLKDIS Counter Clock Disable Command 1 1 write-only SWTRG Software Trigger Command 2 1 write-only CMR2 Channel Mode Register (channel = 2) 0x00000084 32 read-write 0x00000000 TCCLKS Clock Selection 0 3 read-write TIMER_CLOCK1 Clock selected: TCLK1 0x0 TIMER_CLOCK2 Clock selected: TCLK2 0x1 TIMER_CLOCK3 Clock selected: TCLK3 0x2 TIMER_CLOCK4 Clock selected: TCLK4 0x3 TIMER_CLOCK5 Clock selected: TCLK5 0x4 XC0 Clock selected: XC0 0x5 XC1 Clock selected: XC1 0x6 XC2 Clock selected: XC2 0x7 CLKI Clock Invert 3 1 read-write BURST Burst Signal Selection 4 2 read-write NONE The clock is not gated by an external signal. 0x0 XC0 XC0 is ANDed with the selected clock. 0x1 XC1 XC1 is ANDed with the selected clock. 0x2 XC2 XC2 is ANDed with the selected clock. 0x3 LDBSTOP Counter Clock Stopped with RB Loading 6 1 read-write LDBDIS Counter Clock Disable with RB Loading 7 1 read-write ETRGEDG External Trigger Edge Selection 8 2 read-write NONE The clock is not gated by an external signal. 0x0 RISING Rising edge 0x1 FALLING Falling edge 0x2 EDGE Each edge 0x3 ABETRG TIOA or TIOB External Trigger Selection 10 1 read-write CPCTRG RC Compare Trigger Enable 14 1 read-write WAVE 15 1 read-write LDRA RA Loading Selection 16 2 read-write NONE None 0x0 RISING Rising edge of TIOA 0x1 FALLING Falling edge of TIOA 0x2 EDGE Each edge of TIOA 0x3 LDRB RB Loading Selection 18 2 read-write NONE None 0x0 RISING Rising edge of TIOA 0x1 FALLING Falling edge of TIOA 0x2 EDGE Each edge of TIOA 0x3 CMR2_WAVE_EQ_1 Channel Mode Register (channel = 2) WAVE_EQ_1 0x00000084 32 read-write 0x00000000 TCCLKS Clock Selection 0 3 read-write TIMER_CLOCK1 Clock selected: TCLK1 0x0 TIMER_CLOCK2 Clock selected: TCLK2 0x1 TIMER_CLOCK3 Clock selected: TCLK3 0x2 TIMER_CLOCK4 Clock selected: TCLK4 0x3 TIMER_CLOCK5 Clock selected: TCLK5 0x4 XC0 Clock selected: XC0 0x5 XC1 Clock selected: XC1 0x6 XC2 Clock selected: XC2 0x7 CLKI Clock Invert 3 1 read-write BURST Burst Signal Selection 4 2 read-write NONE The clock is not gated by an external signal. 0x0 XC0 XC0 is ANDed with the selected clock. 0x1 XC1 XC1 is ANDed with the selected clock. 0x2 XC2 XC2 is ANDed with the selected clock. 0x3 CPCSTOP Counter Clock Stopped with RC Compare 6 1 read-write CPCDIS Counter Clock Disable with RC Compare 7 1 read-write EEVTEDG External Event Edge Selection 8 2 read-write NONE None 0x0 RISING Rising edge 0x1 FALLING Falling edge 0x2 EDGE Each edge 0x3 EEVT External Event Selection 10 2 read-write TIOB TIOB 0x0 XC0 XC0 0x1 XC1 XC1 0x2 XC2 XC2 0x3 ENETRG External Event Trigger Enable 12 1 read-write WAVSEL Waveform Selection 13 2 read-write UP UP mode without automatic trigger on RC Compare 0x0 UPDOWN UPDOWN mode without automatic trigger on RC Compare 0x1 UP_RC UP mode with automatic trigger on RC Compare 0x2 UPDOWN_RC UPDOWN mode with automatic trigger on RC Compare 0x3 WAVE 15 1 read-write ACPA RA Compare Effect on TIOA 16 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 ACPC RC Compare Effect on TIOA 18 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 AEEVT External Event Effect on TIOA 20 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 ASWTRG Software Trigger Effect on TIOA 22 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BCPB RB Compare Effect on TIOB 24 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BCPC RC Compare Effect on TIOB 26 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BEEVT External Event Effect on TIOB 28 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BSWTRG Software Trigger Effect on TIOB 30 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 CV2 Counter Value (channel = 2) 0x00000090 32 read-only 0x00000000 CV Counter Value 0 16 read-only RA2 Register A (channel = 2) 0x00000094 32 read-write 0x00000000 RA Register A 0 16 read-write RB2 Register B (channel = 2) 0x00000098 32 read-write 0x00000000 RB Register B 0 16 read-write RC2 Register C (channel = 2) 0x0000009C 32 read-write 0x00000000 RC Register C 0 16 read-write SR2 Status Register (channel = 2) 0x000000A0 32 read-only 0x00000000 COVFS Counter Overflow Status 0 1 read-only LOVRS Load Overrun Status 1 1 read-only CPAS RA Compare Status 2 1 read-only CPBS RB Compare Status 3 1 read-only CPCS RC Compare Status 4 1 read-only LDRAS RA Loading Status 5 1 read-only LDRBS RB Loading Status 6 1 read-only ETRGS External Trigger Status 7 1 read-only CLKSTA Clock Enabling Status 16 1 read-only MTIOA TIOA Mirror 17 1 read-only MTIOB TIOB Mirror 18 1 read-only IER2 Interrupt Enable Register (channel = 2) 0x000000A4 32 write-only COVFS Counter Overflow 0 1 write-only LOVRS Load Overrun 1 1 write-only CPAS RA Compare 2 1 write-only CPBS RB Compare 3 1 write-only CPCS RC Compare 4 1 write-only LDRAS RA Loading 5 1 write-only LDRBS RB Loading 6 1 write-only ETRGS External Trigger 7 1 write-only IDR2 Interrupt Disable Register (channel = 2) 0x000000A8 32 write-only COVFS Counter Overflow 0 1 write-only LOVRS Load Overrun 1 1 write-only CPAS RA Compare 2 1 write-only CPBS RB Compare 3 1 write-only CPCS RC Compare 4 1 write-only LDRAS RA Loading 5 1 write-only LDRBS RB Loading 6 1 write-only ETRGS External Trigger 7 1 write-only IMR2 Interrupt Mask Register (channel = 2) 0x000000AC 32 read-only 0x00000000 COVFS Counter Overflow 0 1 read-only LOVRS Load Overrun 1 1 read-only CPAS RA Compare 2 1 read-only CPBS RB Compare 3 1 read-only CPCS RC Compare 4 1 read-only LDRAS RA Loading 5 1 read-only LDRBS RB Loading 6 1 read-only ETRGS External Trigger 7 1 read-only BCR Block Control Register 0x000000C0 32 write-only SYNC Synchro Command 0 1 write-only BMR Block Mode Register 0x000000C4 32 read-write 0x00000000 TC0XC0S External Clock Signal 0 Selection 0 2 read-write TCLK0 Signal connected to XC0: TCLK0 0x0 TIOA1 Signal connected to XC0: TIOA1 0x2 TIOA2 Signal connected to XC0: TIOA2 0x3 TC1XC1S External Clock Signal 1 Selection 2 2 read-write TCLK1 Signal connected to XC1: TCLK1 0x0 TIOA0 Signal connected to XC1: TIOA0 0x2 TIOA2 Signal connected to XC1: TIOA2 0x3 TC2XC2S External Clock Signal 2 Selection 4 2 read-write TCLK2 Signal connected to XC2: TCLK2 0x0 TIOA1 Signal connected to XC2: TIOA1 0x2 TIOA2 Signal connected to XC2: TIOA2 0x3 UDP 6083V USB Device Port UDP_ 0xFFFA4000 0 0x4000 registers UDP 10 FRM_NUM Frame Number Register 0x00000000 32 read-only 0x00000000 FRM_NUM Frame Number as Defined in the Packet Field Formats 0 11 read-only FRM_ERR Frame Error 16 1 read-only FRM_OK Frame OK 17 1 read-only GLB_STAT Global State Register 0x00000004 32 read-write 0x00000010 FADDEN Function Address Enable 0 1 read-write CONFG Configured 1 1 read-write FADDR Function Address Register 0x00000008 32 read-write 0x00000100 FADD Function Address Value 0 7 read-write FEN Function Enable 8 1 read-write IER Interrupt Enable Register 0x00000010 32 write-only EP0INT Enable Endpoint 0 Interrupt 0 1 write-only EP1INT Enable Endpoint 1 Interrupt 1 1 write-only EP2INT Enable Endpoint 2Interrupt 2 1 write-only EP3INT Enable Endpoint 3 Interrupt 3 1 write-only EP4INT Enable Endpoint 4 Interrupt 4 1 write-only EP5INT Enable Endpoint 5 Interrupt 5 1 write-only RXSUSP Enable UDP Suspend Interrupt 8 1 write-only RXRSM Enable UDP Resume Interrupt 9 1 write-only SOFINT Enable Start Of Frame Interrupt 11 1 write-only WAKEUP Enable UDP bus Wakeup Interrupt 13 1 write-only IDR Interrupt Disable Register 0x00000014 32 write-only EP0INT Disable Endpoint 0 Interrupt 0 1 write-only EP1INT Disable Endpoint 1 Interrupt 1 1 write-only EP2INT Disable Endpoint 2 Interrupt 2 1 write-only EP3INT Disable Endpoint 3 Interrupt 3 1 write-only EP4INT Disable Endpoint 4 Interrupt 4 1 write-only EP5INT Disable Endpoint 5 Interrupt 5 1 write-only RXSUSP Disable UDP Suspend Interrupt 8 1 write-only RXRSM Disable UDP Resume Interrupt 9 1 write-only SOFINT Disable Start Of Frame Interrupt 11 1 write-only WAKEUP Disable USB Bus Interrupt 13 1 write-only IMR Interrupt Mask Register 0x00000018 32 read-only 0x00001200 EP0INT Mask Endpoint 0 Interrupt 0 1 read-only EP1INT Mask Endpoint 1 Interrupt 1 1 read-only EP2INT Mask Endpoint 2 Interrupt 2 1 read-only EP3INT Mask Endpoint 3 Interrupt 3 1 read-only EP4INT Mask Endpoint 4 Interrupt 4 1 read-only EP5INT Mask Endpoint 5 Interrupt 5 1 read-only RXSUSP Mask UDP Suspend Interrupt 8 1 read-only RXRSM Mask UDP Resume Interrupt. 9 1 read-only SOFINT Mask Start Of Frame Interrupt 11 1 read-only BIT12 UDP_IMR Bit 12 12 1 read-only WAKEUP USB Bus WAKEUP Interrupt 13 1 read-only ISR Interrupt Status Register 0x0000001C 32 read-only EP0INT Endpoint 0 Interrupt Status 0 1 read-only EP1INT Endpoint 1 Interrupt Status 1 1 read-only EP2INT Endpoint 2 Interrupt Status 2 1 read-only EP3INT Endpoint 3 Interrupt Status 3 1 read-only EP4INT Endpoint 4 Interrupt Status 4 1 read-only EP5INT Endpoint 5 Interrupt Status 5 1 read-only RXSUSP UDP Suspend Interrupt Status 8 1 read-only RXRSM UDP Resume Interrupt Status 9 1 read-only SOFINT Start of Frame Interrupt Status 11 1 read-only ENDBUSRES End of BUS Reset Interrupt Status 12 1 read-only WAKEUP UDP Resume Interrupt Status 13 1 read-only ICR Interrupt Clear Register 0x00000020 32 write-only RXSUSP Clear UDP Suspend Interrupt 8 1 write-only RXRSM Clear UDP Resume Interrupt 9 1 write-only SOFINT Clear Start Of Frame Interrupt 11 1 write-only ENDBUSRES Clear End of Bus Reset Interrupt 12 1 write-only WAKEUP Clear Wakeup Interrupt 13 1 write-only RST_EP Reset Endpoint Register 0x00000028 32 read-write 0x00000000 EP0 Reset Endpoint 0 0 1 read-write EP1 Reset Endpoint 1 1 1 read-write EP2 Reset Endpoint 2 2 1 read-write EP3 Reset Endpoint 3 3 1 read-write EP4 Reset Endpoint 4 4 1 read-write EP5 Reset Endpoint 5 5 1 read-write 6 4 0-5 CSR[%s] Endpoint Control and Status Register 0x00000030 32 read-write TXCOMP Generates an IN Packet with Data Previously Written in the DPR 0 1 read-write RX_DATA_BK0 Receive Data Bank 0 1 1 read-write RXSETUP Received Setup 2 1 read-write STALLSENT Stall Sent 3 1 read-write TXPKTRDY Transmit Packet Ready 4 1 read-write FORCESTALL Force Stall (used by Control, Bulk and Isochronous Endpoints) 5 1 read-write RX_DATA_BK1 Receive Data Bank 1 (only used by endpoints with ping-pong attributes) 6 1 read-write DIR Transfer Direction (only available for control endpoints) 7 1 read-write EPTYPE Endpoint Type 8 3 read-write CTRL Control 0x0 ISO_OUT Isochronous OUT 0x1 BULK_OUT Bulk OUT 0x2 INT_OUT Interrupt OUT 0x3 ISO_IN Isochronous IN 0x5 BULK_IN Bulk IN 0x6 INT_IN Interrupt IN 0x7 DTGLE Data Toggle 11 1 read-write EPEDS Endpoint Enable Disable 15 1 read-write RXBYTECNT Number of Bytes Available in the FIFO 16 11 read-write CSR0_ISOENDPT Endpoint Control and Status Register ISOENDPT 0x00000030 32 read-write TXCOMP Generates an IN Packet with Data Previously Written in the DPR 0 1 read-write RX_DATA_BK0 Receive Data Bank 0 1 1 read-write RXSETUP Received Setup 2 1 read-write ISOERROR A CRC error has been detected in an isochronous transfer 3 1 read-write TXPKTRDY Transmit Packet Ready 4 1 read-write FORCESTALL Force Stall (used by Control, Bulk and Isochronous Endpoints) 5 1 read-write RX_DATA_BK1 Receive Data Bank 1 (only used by endpoints with ping-pong attributes) 6 1 read-write DIR Transfer Direction (only available for control endpoints) 7 1 read-write EPTYPE Endpoint Type 8 3 read-write CTRL Control 0x0 ISO_OUT Isochronous OUT 0x1 ISO_IN Isochronous IN 0x5 BULK_OUT Bulk OUT 0x2 BULK_IN Bulk IN 0x6 INT_OUT Interrupt OUT 0x3 INT_IN Interrupt IN 0x7 DTGLE Data Toggle 11 1 read-write EPEDS Endpoint Enable Disable 15 1 read-write RXBYTECNT Number of Bytes Available in the FIFO 16 11 read-write 6 4 0-5 FDR[%s] Endpoint FIFO Data Register 0x00000050 32 read-write FIFO_DATA FIFO Data Value 0 8 read-write TXVC Transceiver Control Register 0x00000074 32 read-write 0x00000100 TXVDIS Transceiver Disable 8 1 read-write PUON Pull-up On 9 1 read-write MCI 6101G MultiMedia Card Interface MCI_ 0xFFFA8000 0 0x4000 registers MCI 9 CR Control Register 0x00000000 32 write-only MCIEN Multi-Media Interface Enable 0 1 write-only MCIDIS Multi-Media Interface Disable 1 1 write-only PWSEN Power Save Mode Enable 2 1 write-only PWSDIS Power Save Mode Disable 3 1 write-only SWRST Software Reset 7 1 write-only MR Mode Register 0x00000004 32 read-write 0x00000000 CLKDIV Clock Divider 0 8 read-write PWSDIV Power Saving Divider 8 3 read-write RDPROOF 11 1 read-write WRPROOF 12 1 read-write PDCFBYTE PDC Force Byte Transfer 13 1 read-write PDCPADV PDC Padding Value 14 1 read-write PDCMODE PDC-oriented Mode 15 1 read-write BLKLEN Data Block Length 16 16 read-write DTOR Data Timeout Register 0x00000008 32 read-write 0x00000000 DTOCYC Data Timeout Cycle Number 0 4 read-write DTOMUL Data Timeout Multiplier 4 3 read-write SDCR SD/SDIO Card Register 0x0000000C 32 read-write 0x00000000 SDCSEL SDCard/SDIO Slot 0 2 read-write SDCBUS SDCard/SDIO Bus Width 7 1 read-write ARGR Argument Register 0x00000010 32 read-write 0x00000000 ARG Command Argument 0 32 read-write CMDR Command Register 0x00000014 32 write-only CMDNB Command Number 0 6 write-only RSPTYP Response Type 6 2 write-only SPCMD Special Command 8 3 write-only OPDCMD Open Drain Command 11 1 write-only MAXLAT Max Latency for Command to Response 12 1 write-only TRCMD Transfer Command 16 2 write-only TRDIR Transfer Direction 18 1 write-only TRTYP Transfer Type 19 3 write-only IOSPCMD SDIO Special Command 24 2 write-only BLKR Block Register 0x00000018 32 read-write 0x00000000 BCNT MMC/SDIO Block Count - SDIO Byte Count 0 16 read-write BLKLEN Data Block Length 16 16 read-write 4 4 0-3 RSPR[%s] Response Register 0x00000020 32 read-only RSP Response 0 32 read-only RDR Receive Data Register 0x00000030 32 read-only 0x00000000 DATA Data to Read 0 32 read-only TDR Transmit Data Register 0x00000034 32 write-only DATA Data to Write 0 32 write-only SR Status Register 0x00000040 32 read-only 0x0000C0E5 CMDRDY Command Ready 0 1 read-only RXRDY Receiver Ready 1 1 read-only TXRDY Transmit Ready 2 1 read-only BLKE Data Block Ended 3 1 read-only DTIP Data Transfer in Progress 4 1 read-only NOTBUSY MCI Not Busy 5 1 read-only ENDRX End of RX Buffer 6 1 read-only ENDTX End of TX Buffer 7 1 read-only RXBUFF RX Buffer Full 14 1 read-only TXBUFE TX Buffer Empty 15 1 read-only RINDE Response Index Error 16 1 read-only RDIRE Response Direction Error 17 1 read-only RCRCE Response CRC Error 18 1 read-only RENDE Response End Bit Error 19 1 read-only RTOE Response Time-out Error 20 1 read-only DCRCE Data CRC Error 21 1 read-only DTOE Data Time-out Error 22 1 read-only OVRE Overrun 30 1 read-only UNRE Underrun 31 1 read-only IER Interrupt Enable Register 0x00000044 32 write-only CMDRDY Command Ready Interrupt Enable 0 1 write-only RXRDY Receiver Ready Interrupt Enable 1 1 write-only TXRDY Transmit Ready Interrupt Enable 2 1 write-only BLKE Data Block Ended Interrupt Enable 3 1 write-only DTIP Data Transfer in Progress Interrupt Enable 4 1 write-only NOTBUSY Data Not Busy Interrupt Enable 5 1 write-only ENDRX End of Receive Buffer Interrupt Enable 6 1 write-only ENDTX End of Transmit Buffer Interrupt Enable 7 1 write-only RXBUFF Receive Buffer Full Interrupt Enable 14 1 write-only TXBUFE Transmit Buffer Empty Interrupt Enable 15 1 write-only RINDE Response Index Error Interrupt Enable 16 1 write-only RDIRE Response Direction Error Interrupt Enable 17 1 write-only RCRCE Response CRC Error Interrupt Enable 18 1 write-only RENDE Response End Bit Error Interrupt Enable 19 1 write-only RTOE Response Time-out Error Interrupt Enable 20 1 write-only DCRCE Data CRC Error Interrupt Enable 21 1 write-only DTOE Data Time-out Error Interrupt Enable 22 1 write-only OVRE Overrun Interrupt Enable 30 1 write-only UNRE UnderRun Interrupt Enable 31 1 write-only IDR Interrupt Disable Register 0x00000048 32 write-only CMDRDY Command Ready Interrupt Disable 0 1 write-only RXRDY Receiver Ready Interrupt Disable 1 1 write-only TXRDY Transmit Ready Interrupt Disable 2 1 write-only BLKE Data Block Ended Interrupt Disable 3 1 write-only DTIP Data Transfer in Progress Interrupt Disable 4 1 write-only NOTBUSY Data Not Busy Interrupt Disable 5 1 write-only ENDRX End of Receive Buffer Interrupt Disable 6 1 write-only ENDTX End of Transmit Buffer Interrupt Disable 7 1 write-only RXBUFF Receive Buffer Full Interrupt Disable 14 1 write-only TXBUFE Transmit Buffer Empty Interrupt Disable 15 1 write-only RINDE Response Index Error Interrupt Disable 16 1 write-only RDIRE Response Direction Error Interrupt Disable 17 1 write-only RCRCE Response CRC Error Interrupt Disable 18 1 write-only RENDE Response End Bit Error Interrupt Disable 19 1 write-only RTOE Response Time-out Error Interrupt Disable 20 1 write-only DCRCE Data CRC Error Interrupt Disable 21 1 write-only DTOE Data Time-out Error Interrupt Disable 22 1 write-only OVRE Overrun Interrupt Disable 30 1 write-only UNRE UnderRun Interrupt Disable 31 1 write-only IMR Interrupt Mask Register 0x0000004C 32 read-only 0x00000000 CMDRDY Command Ready Interrupt Mask 0 1 read-only RXRDY Receiver Ready Interrupt Mask 1 1 read-only TXRDY Transmit Ready Interrupt Mask 2 1 read-only BLKE Data Block Ended Interrupt Mask 3 1 read-only DTIP Data Transfer in Progress Interrupt Mask 4 1 read-only NOTBUSY Data Not Busy Interrupt Mask 5 1 read-only ENDRX End of Receive Buffer Interrupt Mask 6 1 read-only ENDTX End of Transmit Buffer Interrupt Mask 7 1 read-only RXBUFF Receive Buffer Full Interrupt Mask 14 1 read-only TXBUFE Transmit Buffer Empty Interrupt Mask 15 1 read-only RINDE Response Index Error Interrupt Mask 16 1 read-only RDIRE Response Direction Error Interrupt Mask 17 1 read-only RCRCE Response CRC Error Interrupt Mask 18 1 read-only RENDE Response End Bit Error Interrupt Mask 19 1 read-only RTOE Response Time-out Error Interrupt Mask 20 1 read-only DCRCE Data CRC Error Interrupt Mask 21 1 read-only DTOE Data Time-out Error Interrupt Mask 22 1 read-only OVRE Overrun Interrupt Mask 30 1 read-only UNRE UnderRun Interrupt Mask 31 1 read-only RPR Receive Pointer Register 0x00000100 32 read-write 0x00000000 RXPTR Receive Pointer Register 0 32 read-write RCR Receive Counter Register 0x00000104 32 read-write 0x00000000 RXCTR Receive Counter Register 0 16 read-write TPR Transmit Pointer Register 0x00000108 32 read-write 0x00000000 TXPTR Transmit Counter Register 0 32 read-write TCR Transmit Counter Register 0x0000010C 32 read-write 0x00000000 TXCTR Transmit Counter Register 0 16 read-write RNPR Receive Next Pointer Register 0x00000110 32 read-write 0x00000000 RXNPTR Receive Next Pointer 0 32 read-write RNCR Receive Next Counter Register 0x00000114 32 read-write 0x00000000 RXNCTR Receive Next Counter 0 16 read-write TNPR Transmit Next Pointer Register 0x00000118 32 read-write 0x00000000 TXNPTR Transmit Next Pointer 0 32 read-write TNCR Transmit Next Counter Register 0x0000011C 32 read-write 0x00000000 TXNCTR Transmit Counter Next 0 16 read-write PTCR Transfer Control Register 0x00000120 32 write-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 write-only RXTDIS Receiver Transfer Disable 1 1 write-only TXTEN Transmitter Transfer Enable 8 1 write-only TXTDIS Transmitter Transfer Disable 9 1 write-only PTSR Transfer Status Register 0x00000124 32 read-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 read-only TXTEN Transmitter Transfer Enable 8 1 read-only TWI 6212L Two-wire Interface TWI_ 0xFFFAC000 0 0x4000 registers TWI 11 CR Control Register 0x00000000 32 write-only START Send a START Condition 0 1 write-only STOP Send a STOP Condition 1 1 write-only MSEN TWI Master Mode Enabled 2 1 write-only MSDIS TWI Master Mode Disabled 3 1 write-only SVEN TWI Slave Mode Enabled 4 1 write-only SVDIS TWI Slave Mode Disabled 5 1 write-only QUICK SMBUS Quick Command 6 1 write-only SWRST Software Reset 7 1 write-only MMR Master Mode Register 0x00000004 32 read-write 0x00000000 IADRSZ Internal Device Address Size 8 2 read-write NONE No internal device address 0x0 1_BYTE One-byte internal device address 0x1 2_BYTE Two-byte internal device address 0x2 3_BYTE Three-byte internal device address 0x3 MREAD Master Read Direction 12 1 read-write DADR Device Address 16 7 read-write SMR Slave Mode Register 0x00000008 32 read-write 0x00000000 SADR Slave Address 16 7 read-write IADR Internal Address Register 0x0000000C 32 read-write 0x00000000 IADR Internal Address 0 24 read-write CWGR Clock Waveform Generator Register 0x00000010 32 read-write 0x00000000 CLDIV Clock Low Divider 0 8 read-write CHDIV Clock High Divider 8 8 read-write CKDIV Clock Divider 16 3 read-write SR Status Register 0x00000020 32 read-only 0x0000F009 TXCOMP Transmission Completed (automatically set / reset) 0 1 read-only RXRDY Receive Holding Register Ready (automatically set / reset) 1 1 read-only TXRDY Transmit Holding Register Ready (automatically set / reset) 2 1 read-only SVREAD Slave Read (automatically set / reset) 3 1 read-only SVACC Slave Access (automatically set / reset) 4 1 read-only GACC General Call Access (clear on read) 5 1 read-only OVRE Overrun Error (clear on read) 6 1 read-only NACK Not Acknowledged (clear on read) 8 1 read-only ARBLST Arbitration Lost (clear on read) 9 1 read-only SCLWS Clock Wait State (automatically set / reset) 10 1 read-only EOSACC End Of Slave Access (clear on read) 11 1 read-only IER Interrupt Enable Register 0x00000024 32 write-only TXCOMP Transmission Completed Interrupt Enable 0 1 write-only RXRDY Receive Holding Register Ready Interrupt Enable 1 1 write-only TXRDY Transmit Holding Register Ready Interrupt Enable 2 1 write-only SVACC Slave Access Interrupt Enable 4 1 write-only GACC General Call Access Interrupt Enable 5 1 write-only OVRE Overrun Error Interrupt Enable 6 1 write-only NACK Not Acknowledge Interrupt Enable 8 1 write-only ARBLST Arbitration Lost Interrupt Enable 9 1 write-only SCL_WS Clock Wait State Interrupt Enable 10 1 write-only EOSACC End Of Slave Access Interrupt Enable 11 1 write-only IDR Interrupt Disable Register 0x00000028 32 write-only TXCOMP Transmission Completed Interrupt Disable 0 1 write-only RXRDY Receive Holding Register Ready Interrupt Disable 1 1 write-only TXRDY Transmit Holding Register Ready Interrupt Disable 2 1 write-only SVACC Slave Access Interrupt Disable 4 1 write-only GACC General Call Access Interrupt Disable 5 1 write-only OVRE Overrun Error Interrupt Disable 6 1 write-only NACK Not Acknowledge Interrupt Disable 8 1 write-only ARBLST Arbitration Lost Interrupt Disable 9 1 write-only SCL_WS Clock Wait State Interrupt Disable 10 1 write-only EOSACC End Of Slave Access Interrupt Disable 11 1 write-only IMR Interrupt Mask Register 0x0000002C 32 read-only 0x00000000 TXCOMP Transmission Completed Interrupt Mask 0 1 read-only RXRDY Receive Holding Register Ready Interrupt Mask 1 1 read-only TXRDY Transmit Holding Register Ready Interrupt Mask 2 1 read-only SVACC Slave Access Interrupt Mask 4 1 read-only GACC General Call Access Interrupt Mask 5 1 read-only OVRE Overrun Error Interrupt Mask 6 1 read-only NACK Not Acknowledge Interrupt Mask 8 1 read-only ARBLST Arbitration Lost Interrupt Mask 9 1 read-only SCL_WS Clock Wait State Interrupt Mask 10 1 read-only EOSACC End Of Slave Access Interrupt Mask 11 1 read-only RHR Receive Holding Register 0x00000030 32 read-only 0x00000000 RXDATA Master or Slave Receive Holding Data 0 8 read-only THR Transmit Holding Register 0x00000034 32 write-only 0x00000000 TXDATA Master or Slave Transmit Holding Data 0 8 write-only RPR Receive Pointer Register 0x00000100 32 read-write 0x00000000 RXPTR Receive Pointer Register 0 32 read-write RCR Receive Counter Register 0x00000104 32 read-write 0x00000000 RXCTR Receive Counter Register 0 16 read-write TPR Transmit Pointer Register 0x00000108 32 read-write 0x00000000 TXPTR Transmit Counter Register 0 32 read-write TCR Transmit Counter Register 0x0000010C 32 read-write 0x00000000 TXCTR Transmit Counter Register 0 16 read-write RNPR Receive Next Pointer Register 0x00000110 32 read-write 0x00000000 RXNPTR Receive Next Pointer 0 32 read-write RNCR Receive Next Counter Register 0x00000114 32 read-write 0x00000000 RXNCTR Receive Next Counter 0 16 read-write TNPR Transmit Next Pointer Register 0x00000118 32 read-write 0x00000000 TXNPTR Transmit Next Pointer 0 32 read-write TNCR Transmit Next Counter Register 0x0000011C 32 read-write 0x00000000 TXNCTR Transmit Counter Next 0 16 read-write PTCR Transfer Control Register 0x00000120 32 write-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 write-only RXTDIS Receiver Transfer Disable 1 1 write-only TXTEN Transmitter Transfer Enable 8 1 write-only TXTDIS Transmitter Transfer Disable 9 1 write-only PTSR Transfer Status Register 0x00000124 32 read-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 read-only TXTEN Transmitter Transfer Enable 8 1 read-only USART0 6089V Universal Synchronous Asynchronous Receiver Transmitter 0 USART USART0_ 0xFFFB0000 0 0x4000 registers USART0 6 CR Control Register 0x00000000 32 write-only RSTRX Reset Receiver 2 1 write-only RSTTX Reset Transmitter 3 1 write-only RXEN Receiver Enable 4 1 write-only RXDIS Receiver Disable 5 1 write-only TXEN Transmitter Enable 6 1 write-only TXDIS Transmitter Disable 7 1 write-only RSTSTA Reset Status Bits 8 1 write-only STTBRK Start Break 9 1 write-only STPBRK Stop Break 10 1 write-only STTTO Start Time-out 11 1 write-only SENDA Send Address 12 1 write-only RSTIT Reset Iterations 13 1 write-only RSTNACK Reset Non Acknowledge 14 1 write-only RETTO Rearm Time-out 15 1 write-only DTREN Data Terminal Ready Enable 16 1 write-only DTRDIS Data Terminal Ready Disable 17 1 write-only RTSEN Request to Send Enable 18 1 write-only RTSDIS Request to Send Disable 19 1 write-only MR Mode Register 0x00000004 32 read-write USART_MODE 0 4 read-write NORMAL Normal mode 0x0 RS485 RS485 0x1 HW_HANDSHAKING Hardware Handshaking 0x2 MODEM Modem 0x3 IS07816_T_0 IS07816 Protocol: T = 0 0x4 IS07816_T_1 IS07816 Protocol: T = 1 0x6 IRDA IrDA 0x8 USCLKS Clock Selection 4 2 read-write MCK Master Clock MCK is selected 0x0 DIV Internal Clock Divided MCK/DIV (DIV=8) is selected 0x1 SCK Serial Clock SLK is selected 0x3 CHRL Character Length. 6 2 read-write 5_BIT Character length is 5 bits 0x0 6_BIT Character length is 6 bits 0x1 7_BIT Character length is 7 bits 0x2 8_BIT Character length is 8 bits 0x3 SYNC Synchronous Mode Select 8 1 read-write PAR Parity Type 9 3 read-write EVEN Even parity 0x0 ODD Odd parity 0x1 SPACE Parity forced to 0 (Space) 0x2 MARK Parity forced to 1 (Mark) 0x3 NO No parity 0x4 MULTIDROP Multidrop mode 0x6 NBSTOP Number of Stop Bits 12 2 read-write 1_BIT 1 stop bit 0x0 1_5_BIT 1.5 stop bit (SYNC = 0) or reserved (SYNC = 1) 0x1 2_BIT 2 stop bits 0x2 CHMODE Channel Mode 14 2 read-write NORMAL Normal Mode 0x0 AUTOMATIC Automatic Echo. Receiver input is connected to the TXD pin. 0x1 LOCAL_LOOPBACK Local Loopback. Transmitter output is connected to the Receiver Input. 0x2 REMOTE_LOOPBACK Remote Loopback. RXD pin is internally connected to the TXD pin. 0x3 MSBF Bit Order 16 1 read-write MODE9 9-bit Character Length 17 1 read-write CLKO Clock Output Select 18 1 read-write OVER Oversampling Mode 19 1 read-write INACK Inhibit Non Acknowledge 20 1 read-write DSNACK Disable Successive NACK 21 1 read-write VAR_SYNC Variable Synchronization of Command/Data Sync Start Frame Delimiter 22 1 read-write MAX_ITERATION 24 3 read-write FILTER Infrared Receive Line Filter 28 1 read-write MAN Manchester Encoder/Decoder Enable 29 1 read-write MODSYNC Manchester Synchronization Mode 30 1 read-write ONEBIT Start Frame Delimiter Selector 31 1 read-write IER Interrupt Enable Register 0x00000008 32 write-only RXRDY RXRDY Interrupt Enable 0 1 write-only TXRDY TXRDY Interrupt Enable 1 1 write-only RXBRK Receiver Break Interrupt Enable 2 1 write-only ENDRX End of Receive Transfer Interrupt Enable 3 1 write-only ENDTX End of Transmit Interrupt Enable 4 1 write-only OVRE Overrun Error Interrupt Enable 5 1 write-only FRAME Framing Error Interrupt Enable 6 1 write-only PARE Parity Error Interrupt Enable 7 1 write-only TIMEOUT Time-out Interrupt Enable 8 1 write-only TXEMPTY TXEMPTY Interrupt Enable 9 1 write-only ITER Max number of Repetitions Reached 10 1 write-only TXBUFE Buffer Empty Interrupt Enable 11 1 write-only RXBUFF Buffer Full Interrupt Enable 12 1 write-only NACK Non AcknowledgeInterrupt Enable 13 1 write-only RIIC Ring Indicator Input Change Enable 16 1 write-only DSRIC Data Set Ready Input Change Enable 17 1 write-only DCDIC Data Carrier Detect Input Change Interrupt Enable 18 1 write-only CTSIC Clear to Send Input Change Interrupt Enable 19 1 write-only MANE Manchester Error Interrupt Enable 24 1 write-only IDR Interrupt Disable Register 0x0000000C 32 write-only RXRDY RXRDY Interrupt Disable 0 1 write-only TXRDY TXRDY Interrupt Disable 1 1 write-only RXBRK Receiver Break Interrupt Disable 2 1 write-only ENDRX End of Receive Transfer Interrupt Disable 3 1 write-only ENDTX End of Transmit Interrupt Disable 4 1 write-only OVRE Overrun Error Interrupt Disable 5 1 write-only FRAME Framing Error Interrupt Disable 6 1 write-only PARE Parity Error Interrupt Disable 7 1 write-only TIMEOUT Time-out Interrupt Disable 8 1 write-only TXEMPTY TXEMPTY Interrupt Disable 9 1 write-only ITER Max number of Repetitions Reached Disable 10 1 write-only TXBUFE Buffer Empty Interrupt Disable 11 1 write-only RXBUFF Buffer Full Interrupt Disable 12 1 write-only NACK Non AcknowledgeInterrupt Disable 13 1 write-only RIIC Ring Indicator Input Change Disable 16 1 write-only DSRIC Data Set Ready Input Change Disable 17 1 write-only DCDIC Data Carrier Detect Input Change Interrupt Disable 18 1 write-only CTSIC Clear to Send Input Change Interrupt Disable 19 1 write-only MANE Manchester Error Interrupt Disable 24 1 write-only IMR Interrupt Mask Register 0x00000010 32 read-only 0x00000000 RXRDY RXRDY Interrupt Mask 0 1 read-only TXRDY TXRDY Interrupt Mask 1 1 read-only RXBRK Receiver Break Interrupt Mask 2 1 read-only ENDRX End of Receive Transfer Interrupt Mask 3 1 read-only ENDTX End of Transmit Interrupt Mask 4 1 read-only OVRE Overrun Error Interrupt Mask 5 1 read-only FRAME Framing Error Interrupt Mask 6 1 read-only PARE Parity Error Interrupt Mask 7 1 read-only TIMEOUT Time-out Interrupt Mask 8 1 read-only TXEMPTY TXEMPTY Interrupt Mask 9 1 read-only ITER Max number of Repetitions Reached Mask 10 1 read-only TXBUFE Buffer Empty Interrupt Mask 11 1 read-only RXBUFF Buffer Full Interrupt Mask 12 1 read-only NACK Non AcknowledgeInterrupt Mask 13 1 read-only RIIC Ring Indicator Input Change Mask 16 1 read-only DSRIC Data Set Ready Input Change Mask 17 1 read-only DCDIC Data Carrier Detect Input Change Interrupt Mask 18 1 read-only CTSIC Clear to Send Input Change Interrupt Mask 19 1 read-only MANE Manchester Error Interrupt Mask 24 1 read-only CSR Channel Status Register 0x00000014 32 read-only RXRDY Receiver Ready 0 1 read-only TXRDY Transmitter Ready 1 1 read-only RXBRK Break Received/End of Break 2 1 read-only ENDRX End of Receiver Transfer 3 1 read-only ENDTX End of Transmitter Transfer 4 1 read-only OVRE Overrun Error 5 1 read-only FRAME Framing Error 6 1 read-only PARE Parity Error 7 1 read-only TIMEOUT Receiver Time-out 8 1 read-only TXEMPTY Transmitter Empty 9 1 read-only ITER Max number of Repetitions Reached 10 1 read-only TXBUFE Transmission Buffer Empty 11 1 read-only RXBUFF Reception Buffer Full 12 1 read-only NACK Non AcknowledgeInterrupt 13 1 read-only RIIC Ring Indicator Input Change Flag 16 1 read-only DSRIC Data Set Ready Input Change Flag 17 1 read-only DCDIC Data Carrier Detect Input Change Flag 18 1 read-only CTSIC Clear to Send Input Change Flag 19 1 read-only RI Image of RI Input 20 1 read-only DSR Image of DSR Input 21 1 read-only DCD Image of DCD Input 22 1 read-only CTS Image of CTS Input 23 1 read-only MANERR Manchester Error 24 1 read-only RHR Receiver Holding Register 0x00000018 32 read-only 0x00000000 RXCHR Received Character 0 9 read-only RXSYNH Received Sync 15 1 read-only THR Transmitter Holding Register 0x0000001C 32 write-only TXCHR Character to be Transmitted 0 9 write-only TXSYNH Sync Field to be transmitted 15 1 write-only BRGR Baud Rate Generator Register 0x00000020 32 read-write 0x00000000 CD Clock Divider 0 16 read-write FP Fractional Part 16 3 read-write RTOR Receiver Time-out Register 0x00000024 32 read-write 0x00000000 TO Time-out Value 0 16 read-write TTGR Transmitter Timeguard Register 0x00000028 32 read-write 0x00000000 TG Timeguard Value 0 8 read-write FIDI FI DI Ratio Register 0x00000040 32 read-write 0x00000174 FI_DI_RATIO FI Over DI Ratio Value 0 11 read-write NER Number of Errors Register 0x00000044 32 read-only NB_ERRORS Number of Errors 0 8 read-only IF IrDA Filter Register 0x0000004C 32 read-write 0x00000000 IRDA_FILTER IrDA Filter 0 8 read-write MAN Manchester Encoder Decoder Register 0x00000050 32 read-write 0x30011004 TX_PL Transmitter Preamble Length 0 4 read-write TX_PP Transmitter Preamble Pattern 8 2 read-write ALL_ONE The preamble is composed of '1's 0x0 ALL_ZERO The preamble is composed of '0's 0x1 ZERO_ONE The preamble is composed of '01's 0x2 ONE_ZERO The preamble is composed of '10's 0x3 TX_MPOL Transmitter Manchester Polarity 12 1 read-write RX_PL Receiver Preamble Length 16 4 read-write RX_PP Receiver Preamble Pattern detected 24 2 read-write ALL_ONE The preamble is composed of '1's 0x0 ALL_ZERO The preamble is composed of '0's 0x1 ZERO_ONE The preamble is composed of '01's 0x2 ONE_ZERO The preamble is composed of '10's 0x3 RX_MPOL Receiver Manchester Polarity 28 1 read-write STUCKTO1 29 1 read-write DRIFT Drift compensation 30 1 read-write RPR Receive Pointer Register 0x00000100 32 read-write 0x00000000 RXPTR Receive Pointer Register 0 32 read-write RCR Receive Counter Register 0x00000104 32 read-write 0x00000000 RXCTR Receive Counter Register 0 16 read-write TPR Transmit Pointer Register 0x00000108 32 read-write 0x00000000 TXPTR Transmit Counter Register 0 32 read-write TCR Transmit Counter Register 0x0000010C 32 read-write 0x00000000 TXCTR Transmit Counter Register 0 16 read-write RNPR Receive Next Pointer Register 0x00000110 32 read-write 0x00000000 RXNPTR Receive Next Pointer 0 32 read-write RNCR Receive Next Counter Register 0x00000114 32 read-write 0x00000000 RXNCTR Receive Next Counter 0 16 read-write TNPR Transmit Next Pointer Register 0x00000118 32 read-write 0x00000000 TXNPTR Transmit Next Pointer 0 32 read-write TNCR Transmit Next Counter Register 0x0000011C 32 read-write 0x00000000 TXNCTR Transmit Counter Next 0 16 read-write PTCR Transfer Control Register 0x00000120 32 write-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 write-only RXTDIS Receiver Transfer Disable 1 1 write-only TXTEN Transmitter Transfer Enable 8 1 write-only TXTDIS Transmitter Transfer Disable 9 1 write-only PTSR Transfer Status Register 0x00000124 32 read-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 read-only TXTEN Transmitter Transfer Enable 8 1 read-only USART1 6089V Universal Synchronous Asynchronous Receiver Transmitter 1 USART USART1_ 0xFFFB4000 0 0x4000 registers USART1 7 CR Control Register 0x00000000 32 write-only RSTRX Reset Receiver 2 1 write-only RSTTX Reset Transmitter 3 1 write-only RXEN Receiver Enable 4 1 write-only RXDIS Receiver Disable 5 1 write-only TXEN Transmitter Enable 6 1 write-only TXDIS Transmitter Disable 7 1 write-only RSTSTA Reset Status Bits 8 1 write-only STTBRK Start Break 9 1 write-only STPBRK Stop Break 10 1 write-only STTTO Start Time-out 11 1 write-only SENDA Send Address 12 1 write-only RSTIT Reset Iterations 13 1 write-only RSTNACK Reset Non Acknowledge 14 1 write-only RETTO Rearm Time-out 15 1 write-only DTREN Data Terminal Ready Enable 16 1 write-only DTRDIS Data Terminal Ready Disable 17 1 write-only RTSEN Request to Send Enable 18 1 write-only RTSDIS Request to Send Disable 19 1 write-only MR Mode Register 0x00000004 32 read-write USART_MODE 0 4 read-write NORMAL Normal mode 0x0 RS485 RS485 0x1 HW_HANDSHAKING Hardware Handshaking 0x2 MODEM Modem 0x3 IS07816_T_0 IS07816 Protocol: T = 0 0x4 IS07816_T_1 IS07816 Protocol: T = 1 0x6 IRDA IrDA 0x8 USCLKS Clock Selection 4 2 read-write MCK Master Clock MCK is selected 0x0 DIV Internal Clock Divided MCK/DIV (DIV=8) is selected 0x1 SCK Serial Clock SLK is selected 0x3 CHRL Character Length. 6 2 read-write 5_BIT Character length is 5 bits 0x0 6_BIT Character length is 6 bits 0x1 7_BIT Character length is 7 bits 0x2 8_BIT Character length is 8 bits 0x3 SYNC Synchronous Mode Select 8 1 read-write PAR Parity Type 9 3 read-write EVEN Even parity 0x0 ODD Odd parity 0x1 SPACE Parity forced to 0 (Space) 0x2 MARK Parity forced to 1 (Mark) 0x3 NO No parity 0x4 MULTIDROP Multidrop mode 0x6 NBSTOP Number of Stop Bits 12 2 read-write 1_BIT 1 stop bit 0x0 1_5_BIT 1.5 stop bit (SYNC = 0) or reserved (SYNC = 1) 0x1 2_BIT 2 stop bits 0x2 CHMODE Channel Mode 14 2 read-write NORMAL Normal Mode 0x0 AUTOMATIC Automatic Echo. Receiver input is connected to the TXD pin. 0x1 LOCAL_LOOPBACK Local Loopback. Transmitter output is connected to the Receiver Input. 0x2 REMOTE_LOOPBACK Remote Loopback. RXD pin is internally connected to the TXD pin. 0x3 MSBF Bit Order 16 1 read-write MODE9 9-bit Character Length 17 1 read-write CLKO Clock Output Select 18 1 read-write OVER Oversampling Mode 19 1 read-write INACK Inhibit Non Acknowledge 20 1 read-write DSNACK Disable Successive NACK 21 1 read-write VAR_SYNC Variable Synchronization of Command/Data Sync Start Frame Delimiter 22 1 read-write MAX_ITERATION 24 3 read-write FILTER Infrared Receive Line Filter 28 1 read-write MAN Manchester Encoder/Decoder Enable 29 1 read-write MODSYNC Manchester Synchronization Mode 30 1 read-write ONEBIT Start Frame Delimiter Selector 31 1 read-write IER Interrupt Enable Register 0x00000008 32 write-only RXRDY RXRDY Interrupt Enable 0 1 write-only TXRDY TXRDY Interrupt Enable 1 1 write-only RXBRK Receiver Break Interrupt Enable 2 1 write-only ENDRX End of Receive Transfer Interrupt Enable 3 1 write-only ENDTX End of Transmit Interrupt Enable 4 1 write-only OVRE Overrun Error Interrupt Enable 5 1 write-only FRAME Framing Error Interrupt Enable 6 1 write-only PARE Parity Error Interrupt Enable 7 1 write-only TIMEOUT Time-out Interrupt Enable 8 1 write-only TXEMPTY TXEMPTY Interrupt Enable 9 1 write-only ITER Max number of Repetitions Reached 10 1 write-only TXBUFE Buffer Empty Interrupt Enable 11 1 write-only RXBUFF Buffer Full Interrupt Enable 12 1 write-only NACK Non AcknowledgeInterrupt Enable 13 1 write-only RIIC Ring Indicator Input Change Enable 16 1 write-only DSRIC Data Set Ready Input Change Enable 17 1 write-only DCDIC Data Carrier Detect Input Change Interrupt Enable 18 1 write-only CTSIC Clear to Send Input Change Interrupt Enable 19 1 write-only MANE Manchester Error Interrupt Enable 24 1 write-only IDR Interrupt Disable Register 0x0000000C 32 write-only RXRDY RXRDY Interrupt Disable 0 1 write-only TXRDY TXRDY Interrupt Disable 1 1 write-only RXBRK Receiver Break Interrupt Disable 2 1 write-only ENDRX End of Receive Transfer Interrupt Disable 3 1 write-only ENDTX End of Transmit Interrupt Disable 4 1 write-only OVRE Overrun Error Interrupt Disable 5 1 write-only FRAME Framing Error Interrupt Disable 6 1 write-only PARE Parity Error Interrupt Disable 7 1 write-only TIMEOUT Time-out Interrupt Disable 8 1 write-only TXEMPTY TXEMPTY Interrupt Disable 9 1 write-only ITER Max number of Repetitions Reached Disable 10 1 write-only TXBUFE Buffer Empty Interrupt Disable 11 1 write-only RXBUFF Buffer Full Interrupt Disable 12 1 write-only NACK Non AcknowledgeInterrupt Disable 13 1 write-only RIIC Ring Indicator Input Change Disable 16 1 write-only DSRIC Data Set Ready Input Change Disable 17 1 write-only DCDIC Data Carrier Detect Input Change Interrupt Disable 18 1 write-only CTSIC Clear to Send Input Change Interrupt Disable 19 1 write-only MANE Manchester Error Interrupt Disable 24 1 write-only IMR Interrupt Mask Register 0x00000010 32 read-only 0x00000000 RXRDY RXRDY Interrupt Mask 0 1 read-only TXRDY TXRDY Interrupt Mask 1 1 read-only RXBRK Receiver Break Interrupt Mask 2 1 read-only ENDRX End of Receive Transfer Interrupt Mask 3 1 read-only ENDTX End of Transmit Interrupt Mask 4 1 read-only OVRE Overrun Error Interrupt Mask 5 1 read-only FRAME Framing Error Interrupt Mask 6 1 read-only PARE Parity Error Interrupt Mask 7 1 read-only TIMEOUT Time-out Interrupt Mask 8 1 read-only TXEMPTY TXEMPTY Interrupt Mask 9 1 read-only ITER Max number of Repetitions Reached Mask 10 1 read-only TXBUFE Buffer Empty Interrupt Mask 11 1 read-only RXBUFF Buffer Full Interrupt Mask 12 1 read-only NACK Non AcknowledgeInterrupt Mask 13 1 read-only RIIC Ring Indicator Input Change Mask 16 1 read-only DSRIC Data Set Ready Input Change Mask 17 1 read-only DCDIC Data Carrier Detect Input Change Interrupt Mask 18 1 read-only CTSIC Clear to Send Input Change Interrupt Mask 19 1 read-only MANE Manchester Error Interrupt Mask 24 1 read-only CSR Channel Status Register 0x00000014 32 read-only RXRDY Receiver Ready 0 1 read-only TXRDY Transmitter Ready 1 1 read-only RXBRK Break Received/End of Break 2 1 read-only ENDRX End of Receiver Transfer 3 1 read-only ENDTX End of Transmitter Transfer 4 1 read-only OVRE Overrun Error 5 1 read-only FRAME Framing Error 6 1 read-only PARE Parity Error 7 1 read-only TIMEOUT Receiver Time-out 8 1 read-only TXEMPTY Transmitter Empty 9 1 read-only ITER Max number of Repetitions Reached 10 1 read-only TXBUFE Transmission Buffer Empty 11 1 read-only RXBUFF Reception Buffer Full 12 1 read-only NACK Non AcknowledgeInterrupt 13 1 read-only RIIC Ring Indicator Input Change Flag 16 1 read-only DSRIC Data Set Ready Input Change Flag 17 1 read-only DCDIC Data Carrier Detect Input Change Flag 18 1 read-only CTSIC Clear to Send Input Change Flag 19 1 read-only RI Image of RI Input 20 1 read-only DSR Image of DSR Input 21 1 read-only DCD Image of DCD Input 22 1 read-only CTS Image of CTS Input 23 1 read-only MANERR Manchester Error 24 1 read-only RHR Receiver Holding Register 0x00000018 32 read-only 0x00000000 RXCHR Received Character 0 9 read-only RXSYNH Received Sync 15 1 read-only THR Transmitter Holding Register 0x0000001C 32 write-only TXCHR Character to be Transmitted 0 9 write-only TXSYNH Sync Field to be transmitted 15 1 write-only BRGR Baud Rate Generator Register 0x00000020 32 read-write 0x00000000 CD Clock Divider 0 16 read-write FP Fractional Part 16 3 read-write RTOR Receiver Time-out Register 0x00000024 32 read-write 0x00000000 TO Time-out Value 0 16 read-write TTGR Transmitter Timeguard Register 0x00000028 32 read-write 0x00000000 TG Timeguard Value 0 8 read-write FIDI FI DI Ratio Register 0x00000040 32 read-write 0x00000174 FI_DI_RATIO FI Over DI Ratio Value 0 11 read-write NER Number of Errors Register 0x00000044 32 read-only NB_ERRORS Number of Errors 0 8 read-only IF IrDA Filter Register 0x0000004C 32 read-write 0x00000000 IRDA_FILTER IrDA Filter 0 8 read-write MAN Manchester Encoder Decoder Register 0x00000050 32 read-write 0x30011004 TX_PL Transmitter Preamble Length 0 4 read-write TX_PP Transmitter Preamble Pattern 8 2 read-write ALL_ONE The preamble is composed of '1's 0x0 ALL_ZERO The preamble is composed of '0's 0x1 ZERO_ONE The preamble is composed of '01's 0x2 ONE_ZERO The preamble is composed of '10's 0x3 TX_MPOL Transmitter Manchester Polarity 12 1 read-write RX_PL Receiver Preamble Length 16 4 read-write RX_PP Receiver Preamble Pattern detected 24 2 read-write ALL_ONE The preamble is composed of '1's 0x0 ALL_ZERO The preamble is composed of '0's 0x1 ZERO_ONE The preamble is composed of '01's 0x2 ONE_ZERO The preamble is composed of '10's 0x3 RX_MPOL Receiver Manchester Polarity 28 1 read-write STUCKTO1 29 1 read-write DRIFT Drift compensation 30 1 read-write RPR Receive Pointer Register 0x00000100 32 read-write 0x00000000 RXPTR Receive Pointer Register 0 32 read-write RCR Receive Counter Register 0x00000104 32 read-write 0x00000000 RXCTR Receive Counter Register 0 16 read-write TPR Transmit Pointer Register 0x00000108 32 read-write 0x00000000 TXPTR Transmit Counter Register 0 32 read-write TCR Transmit Counter Register 0x0000010C 32 read-write 0x00000000 TXCTR Transmit Counter Register 0 16 read-write RNPR Receive Next Pointer Register 0x00000110 32 read-write 0x00000000 RXNPTR Receive Next Pointer 0 32 read-write RNCR Receive Next Counter Register 0x00000114 32 read-write 0x00000000 RXNCTR Receive Next Counter 0 16 read-write TNPR Transmit Next Pointer Register 0x00000118 32 read-write 0x00000000 TXNPTR Transmit Next Pointer 0 32 read-write TNCR Transmit Next Counter Register 0x0000011C 32 read-write 0x00000000 TXNCTR Transmit Counter Next 0 16 read-write PTCR Transfer Control Register 0x00000120 32 write-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 write-only RXTDIS Receiver Transfer Disable 1 1 write-only TXTEN Transmitter Transfer Enable 8 1 write-only TXTDIS Transmitter Transfer Disable 9 1 write-only PTSR Transfer Status Register 0x00000124 32 read-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 read-only TXTEN Transmitter Transfer Enable 8 1 read-only USART2 6089V Universal Synchronous Asynchronous Receiver Transmitter 2 USART USART2_ 0xFFFB8000 0 0x4000 registers USART2 8 CR Control Register 0x00000000 32 write-only RSTRX Reset Receiver 2 1 write-only RSTTX Reset Transmitter 3 1 write-only RXEN Receiver Enable 4 1 write-only RXDIS Receiver Disable 5 1 write-only TXEN Transmitter Enable 6 1 write-only TXDIS Transmitter Disable 7 1 write-only RSTSTA Reset Status Bits 8 1 write-only STTBRK Start Break 9 1 write-only STPBRK Stop Break 10 1 write-only STTTO Start Time-out 11 1 write-only SENDA Send Address 12 1 write-only RSTIT Reset Iterations 13 1 write-only RSTNACK Reset Non Acknowledge 14 1 write-only RETTO Rearm Time-out 15 1 write-only DTREN Data Terminal Ready Enable 16 1 write-only DTRDIS Data Terminal Ready Disable 17 1 write-only RTSEN Request to Send Enable 18 1 write-only RTSDIS Request to Send Disable 19 1 write-only MR Mode Register 0x00000004 32 read-write USART_MODE 0 4 read-write NORMAL Normal mode 0x0 RS485 RS485 0x1 HW_HANDSHAKING Hardware Handshaking 0x2 MODEM Modem 0x3 IS07816_T_0 IS07816 Protocol: T = 0 0x4 IS07816_T_1 IS07816 Protocol: T = 1 0x6 IRDA IrDA 0x8 USCLKS Clock Selection 4 2 read-write MCK Master Clock MCK is selected 0x0 DIV Internal Clock Divided MCK/DIV (DIV=8) is selected 0x1 SCK Serial Clock SLK is selected 0x3 CHRL Character Length. 6 2 read-write 5_BIT Character length is 5 bits 0x0 6_BIT Character length is 6 bits 0x1 7_BIT Character length is 7 bits 0x2 8_BIT Character length is 8 bits 0x3 SYNC Synchronous Mode Select 8 1 read-write PAR Parity Type 9 3 read-write EVEN Even parity 0x0 ODD Odd parity 0x1 SPACE Parity forced to 0 (Space) 0x2 MARK Parity forced to 1 (Mark) 0x3 NO No parity 0x4 MULTIDROP Multidrop mode 0x6 NBSTOP Number of Stop Bits 12 2 read-write 1_BIT 1 stop bit 0x0 1_5_BIT 1.5 stop bit (SYNC = 0) or reserved (SYNC = 1) 0x1 2_BIT 2 stop bits 0x2 CHMODE Channel Mode 14 2 read-write NORMAL Normal Mode 0x0 AUTOMATIC Automatic Echo. Receiver input is connected to the TXD pin. 0x1 LOCAL_LOOPBACK Local Loopback. Transmitter output is connected to the Receiver Input. 0x2 REMOTE_LOOPBACK Remote Loopback. RXD pin is internally connected to the TXD pin. 0x3 MSBF Bit Order 16 1 read-write MODE9 9-bit Character Length 17 1 read-write CLKO Clock Output Select 18 1 read-write OVER Oversampling Mode 19 1 read-write INACK Inhibit Non Acknowledge 20 1 read-write DSNACK Disable Successive NACK 21 1 read-write VAR_SYNC Variable Synchronization of Command/Data Sync Start Frame Delimiter 22 1 read-write MAX_ITERATION 24 3 read-write FILTER Infrared Receive Line Filter 28 1 read-write MAN Manchester Encoder/Decoder Enable 29 1 read-write MODSYNC Manchester Synchronization Mode 30 1 read-write ONEBIT Start Frame Delimiter Selector 31 1 read-write IER Interrupt Enable Register 0x00000008 32 write-only RXRDY RXRDY Interrupt Enable 0 1 write-only TXRDY TXRDY Interrupt Enable 1 1 write-only RXBRK Receiver Break Interrupt Enable 2 1 write-only ENDRX End of Receive Transfer Interrupt Enable 3 1 write-only ENDTX End of Transmit Interrupt Enable 4 1 write-only OVRE Overrun Error Interrupt Enable 5 1 write-only FRAME Framing Error Interrupt Enable 6 1 write-only PARE Parity Error Interrupt Enable 7 1 write-only TIMEOUT Time-out Interrupt Enable 8 1 write-only TXEMPTY TXEMPTY Interrupt Enable 9 1 write-only ITER Max number of Repetitions Reached 10 1 write-only TXBUFE Buffer Empty Interrupt Enable 11 1 write-only RXBUFF Buffer Full Interrupt Enable 12 1 write-only NACK Non AcknowledgeInterrupt Enable 13 1 write-only RIIC Ring Indicator Input Change Enable 16 1 write-only DSRIC Data Set Ready Input Change Enable 17 1 write-only DCDIC Data Carrier Detect Input Change Interrupt Enable 18 1 write-only CTSIC Clear to Send Input Change Interrupt Enable 19 1 write-only MANE Manchester Error Interrupt Enable 24 1 write-only IDR Interrupt Disable Register 0x0000000C 32 write-only RXRDY RXRDY Interrupt Disable 0 1 write-only TXRDY TXRDY Interrupt Disable 1 1 write-only RXBRK Receiver Break Interrupt Disable 2 1 write-only ENDRX End of Receive Transfer Interrupt Disable 3 1 write-only ENDTX End of Transmit Interrupt Disable 4 1 write-only OVRE Overrun Error Interrupt Disable 5 1 write-only FRAME Framing Error Interrupt Disable 6 1 write-only PARE Parity Error Interrupt Disable 7 1 write-only TIMEOUT Time-out Interrupt Disable 8 1 write-only TXEMPTY TXEMPTY Interrupt Disable 9 1 write-only ITER Max number of Repetitions Reached Disable 10 1 write-only TXBUFE Buffer Empty Interrupt Disable 11 1 write-only RXBUFF Buffer Full Interrupt Disable 12 1 write-only NACK Non AcknowledgeInterrupt Disable 13 1 write-only RIIC Ring Indicator Input Change Disable 16 1 write-only DSRIC Data Set Ready Input Change Disable 17 1 write-only DCDIC Data Carrier Detect Input Change Interrupt Disable 18 1 write-only CTSIC Clear to Send Input Change Interrupt Disable 19 1 write-only MANE Manchester Error Interrupt Disable 24 1 write-only IMR Interrupt Mask Register 0x00000010 32 read-only 0x00000000 RXRDY RXRDY Interrupt Mask 0 1 read-only TXRDY TXRDY Interrupt Mask 1 1 read-only RXBRK Receiver Break Interrupt Mask 2 1 read-only ENDRX End of Receive Transfer Interrupt Mask 3 1 read-only ENDTX End of Transmit Interrupt Mask 4 1 read-only OVRE Overrun Error Interrupt Mask 5 1 read-only FRAME Framing Error Interrupt Mask 6 1 read-only PARE Parity Error Interrupt Mask 7 1 read-only TIMEOUT Time-out Interrupt Mask 8 1 read-only TXEMPTY TXEMPTY Interrupt Mask 9 1 read-only ITER Max number of Repetitions Reached Mask 10 1 read-only TXBUFE Buffer Empty Interrupt Mask 11 1 read-only RXBUFF Buffer Full Interrupt Mask 12 1 read-only NACK Non AcknowledgeInterrupt Mask 13 1 read-only RIIC Ring Indicator Input Change Mask 16 1 read-only DSRIC Data Set Ready Input Change Mask 17 1 read-only DCDIC Data Carrier Detect Input Change Interrupt Mask 18 1 read-only CTSIC Clear to Send Input Change Interrupt Mask 19 1 read-only MANE Manchester Error Interrupt Mask 24 1 read-only CSR Channel Status Register 0x00000014 32 read-only RXRDY Receiver Ready 0 1 read-only TXRDY Transmitter Ready 1 1 read-only RXBRK Break Received/End of Break 2 1 read-only ENDRX End of Receiver Transfer 3 1 read-only ENDTX End of Transmitter Transfer 4 1 read-only OVRE Overrun Error 5 1 read-only FRAME Framing Error 6 1 read-only PARE Parity Error 7 1 read-only TIMEOUT Receiver Time-out 8 1 read-only TXEMPTY Transmitter Empty 9 1 read-only ITER Max number of Repetitions Reached 10 1 read-only TXBUFE Transmission Buffer Empty 11 1 read-only RXBUFF Reception Buffer Full 12 1 read-only NACK Non AcknowledgeInterrupt 13 1 read-only RIIC Ring Indicator Input Change Flag 16 1 read-only DSRIC Data Set Ready Input Change Flag 17 1 read-only DCDIC Data Carrier Detect Input Change Flag 18 1 read-only CTSIC Clear to Send Input Change Flag 19 1 read-only RI Image of RI Input 20 1 read-only DSR Image of DSR Input 21 1 read-only DCD Image of DCD Input 22 1 read-only CTS Image of CTS Input 23 1 read-only MANERR Manchester Error 24 1 read-only RHR Receiver Holding Register 0x00000018 32 read-only 0x00000000 RXCHR Received Character 0 9 read-only RXSYNH Received Sync 15 1 read-only THR Transmitter Holding Register 0x0000001C 32 write-only TXCHR Character to be Transmitted 0 9 write-only TXSYNH Sync Field to be transmitted 15 1 write-only BRGR Baud Rate Generator Register 0x00000020 32 read-write 0x00000000 CD Clock Divider 0 16 read-write FP Fractional Part 16 3 read-write RTOR Receiver Time-out Register 0x00000024 32 read-write 0x00000000 TO Time-out Value 0 16 read-write TTGR Transmitter Timeguard Register 0x00000028 32 read-write 0x00000000 TG Timeguard Value 0 8 read-write FIDI FI DI Ratio Register 0x00000040 32 read-write 0x00000174 FI_DI_RATIO FI Over DI Ratio Value 0 11 read-write NER Number of Errors Register 0x00000044 32 read-only NB_ERRORS Number of Errors 0 8 read-only IF IrDA Filter Register 0x0000004C 32 read-write 0x00000000 IRDA_FILTER IrDA Filter 0 8 read-write MAN Manchester Encoder Decoder Register 0x00000050 32 read-write 0x30011004 TX_PL Transmitter Preamble Length 0 4 read-write TX_PP Transmitter Preamble Pattern 8 2 read-write ALL_ONE The preamble is composed of '1's 0x0 ALL_ZERO The preamble is composed of '0's 0x1 ZERO_ONE The preamble is composed of '01's 0x2 ONE_ZERO The preamble is composed of '10's 0x3 TX_MPOL Transmitter Manchester Polarity 12 1 read-write RX_PL Receiver Preamble Length 16 4 read-write RX_PP Receiver Preamble Pattern detected 24 2 read-write ALL_ONE The preamble is composed of '1's 0x0 ALL_ZERO The preamble is composed of '0's 0x1 ZERO_ONE The preamble is composed of '01's 0x2 ONE_ZERO The preamble is composed of '10's 0x3 RX_MPOL Receiver Manchester Polarity 28 1 read-write STUCKTO1 29 1 read-write DRIFT Drift compensation 30 1 read-write RPR Receive Pointer Register 0x00000100 32 read-write 0x00000000 RXPTR Receive Pointer Register 0 32 read-write RCR Receive Counter Register 0x00000104 32 read-write 0x00000000 RXCTR Receive Counter Register 0 16 read-write TPR Transmit Pointer Register 0x00000108 32 read-write 0x00000000 TXPTR Transmit Counter Register 0 32 read-write TCR Transmit Counter Register 0x0000010C 32 read-write 0x00000000 TXCTR Transmit Counter Register 0 16 read-write RNPR Receive Next Pointer Register 0x00000110 32 read-write 0x00000000 RXNPTR Receive Next Pointer 0 32 read-write RNCR Receive Next Counter Register 0x00000114 32 read-write 0x00000000 RXNCTR Receive Next Counter 0 16 read-write TNPR Transmit Next Pointer Register 0x00000118 32 read-write 0x00000000 TXNPTR Transmit Next Pointer 0 32 read-write TNCR Transmit Next Counter Register 0x0000011C 32 read-write 0x00000000 TXNCTR Transmit Counter Next 0 16 read-write PTCR Transfer Control Register 0x00000120 32 write-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 write-only RXTDIS Receiver Transfer Disable 1 1 write-only TXTEN Transmitter Transfer Enable 8 1 write-only TXTDIS Transmitter Transfer Disable 9 1 write-only PTSR Transfer Status Register 0x00000124 32 read-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 read-only TXTEN Transmitter Transfer Enable 8 1 read-only SSC0 6078J Synchronous Serial Controller 0 SSC SSC0_ 0xFFFBC000 0 0x4000 registers SSC0 14 CR Control Register 0x00000000 32 write-only RXEN Receive Enable 0 1 write-only RXDIS Receive Disable 1 1 write-only TXEN Transmit Enable 8 1 write-only TXDIS Transmit Disable 9 1 write-only SWRST Software Reset 15 1 write-only CMR Clock Mode Register 0x00000004 32 read-write 0x00000000 DIV Clock Divider 0 12 read-write RCMR Receive Clock Mode Register 0x00000010 32 read-write 0x00000000 CKS Receive Clock Selection 0 2 read-write MCK Divided Clock 0x0 TK TK Clock signal 0x1 RK RK pin 0x2 CKO Receive Clock Output Mode Selection 2 3 read-write NONE None 0x0 CONTINUOUS Continuous Receive Clock 0x1 TRANSFER Receive Clock only during data transfers 0x2 CKI Receive Clock Inversion 5 1 read-write CKG Receive Clock Gating Selection 6 2 read-write NONE None 0x0 CONTINUOUS Continuous Receive Clock 0x1 TRANSFER Receive Clock only during data transfers 0x2 START Receive Start Selection 8 4 read-write CONTINUOUS Continuous, as soon as the receiver is enabled, and immediately after the end of transfer of the previous data. 0x0 TRANSMIT Transmit start 0x1 RF_LOW Detection of a low level on RF signal 0x2 RF_HIGH Detection of a high level on RF signal 0x3 RF_FALLING Detection of a falling edge on RF signal 0x4 RF_RISING Detection of a rising edge on RF signal 0x5 RF_LEVEL Detection of any level change on RF signal 0x6 RF_EDGE Detection of any edge on RF signal 0x7 CMP_0 Compare 0 0x8 STOP Receive Stop Selection 12 1 read-write STTDLY Receive Start Delay 16 8 read-write PERIOD Receive Period Divider Selection 24 8 read-write RFMR Receive Frame Mode Register 0x00000014 32 read-write 0x00000000 DATLEN Data Length 0 5 read-write LOOP Loop Mode 5 1 read-write MSBF Most Significant Bit First 7 1 read-write DATNB Data Number per Frame 8 4 read-write FSLEN Receive Frame Sync Length 16 4 read-write FSOS Receive Frame Sync Output Selection 20 3 read-write NONE None 0x0 NEGATIVE Negative Pulse 0x1 POSITIVE Positive Pulse 0x2 LOW Driven Low during data transfer 0x3 HIGH Driven High during data transfer 0x4 TOGGLING Toggling at each start of data transfer 0x5 FSEDGE Frame Sync Edge Detection 24 1 read-write POSITIVE Positive Edge Detection 0 NEGATIVE Negative Edge Detection 1 TCMR Transmit Clock Mode Register 0x00000018 32 read-write 0x00000000 CKS Transmit Clock Selection 0 2 read-write MCK Divided Clock 0x0 TK TK Clock signal 0x1 RK RK pin 0x2 CKO Transmit Clock Output Mode Selection 2 3 read-write NONE None 0x0 CONTINUOUS Continuous Receive Clock 0x1 TRANSFER Transmit Clock only during data transfers 0x2 CKI Transmit Clock Inversion 5 1 read-write CKG Transmit Clock Gating Selection 6 2 read-write NONE None 0x0 CONTINUOUS Transmit Clock enabled only if TF Low 0x1 TRANSFER Transmit Clock enabled only if TF High 0x2 START Transmit Start Selection 8 4 read-write CONTINUOUS Continuous, as soon as a word is written in the SSC_THR Register (if Transmit is enabled), and immediately after the end of transfer of the previous data. 0x0 RECEIVE Receive start 0x1 RF_LOW Detection of a low level on TF signal 0x2 RF_HIGH Detection of a high level on TF signal 0x3 RF_FALLING Detection of a falling edge on TF signal 0x4 RF_RISING Detection of a rising edge on TF signal 0x5 RF_LEVEL Detection of any level change on TF signal 0x6 RF_EDGE Detection of any edge on TF signal 0x7 CMP_0 Compare 0 0x8 STTDLY Transmit Start Delay 16 8 read-write PERIOD Transmit Period Divider Selection 24 8 read-write TFMR Transmit Frame Mode Register 0x0000001C 32 read-write 0x00000000 DATLEN Data Length 0 5 read-write DATDEF Data Default Value 5 1 read-write MSBF Most Significant Bit First 7 1 read-write DATNB Data Number per frame 8 4 read-write FSLEN Transmit Frame Sync Length 16 4 read-write FSOS Transmit Frame Sync Output Selection 20 3 read-write NONE None 0x0 NEGATIVE Negative Pulse 0x1 POSITIVE Positive Pulse 0x2 LOW Driven Low during data transfer 0x3 HIGH Driven High during data transfer 0x4 TOGGLING Toggling at each start of data transfer 0x5 FSDEN Frame Sync Data Enable 23 1 read-write FSEDGE Frame Sync Edge Detection 24 1 read-write POSITIVE Positive Edge Detection 0 NEGATIVE Negative Edge Detection 1 RHR Receive Holding Register 0x00000020 32 read-only 0x00000000 RDAT Receive Data 0 32 read-only THR Transmit Holding Register 0x00000024 32 write-only TDAT Transmit Data 0 32 write-only RSHR Receive Sync. Holding Register 0x00000030 32 read-only 0x00000000 RSDAT Receive Synchronization Data 0 16 read-only TSHR Transmit Sync. Holding Register 0x00000034 32 read-write 0x00000000 TSDAT Transmit Synchronization Data 0 16 read-write RC0R Receive Compare 0 Register 0x00000038 32 read-write 0x00000000 CP0 Receive Compare Data 0 0 16 read-write RC1R Receive Compare 1 Register 0x0000003C 32 read-write 0x00000000 CP1 Receive Compare Data 1 0 16 read-write SR Status Register 0x00000040 32 read-only 0x000000CC TXRDY Transmit Ready 0 1 read-only TXEMPTY Transmit Empty 1 1 read-only ENDTX End of Transmission 2 1 read-only TXBUFE Transmit Buffer Empty 3 1 read-only RXRDY Receive Ready 4 1 read-only OVRUN Receive Overrun 5 1 read-only ENDRX End of Reception 6 1 read-only RXBUFF Receive Buffer Full 7 1 read-only CP0 Compare 0 8 1 read-only CP1 Compare 1 9 1 read-only TXSYN Transmit Sync 10 1 read-only RXSYN Receive Sync 11 1 read-only TXEN Transmit Enable 16 1 read-only RXEN Receive Enable 17 1 read-only IER Interrupt Enable Register 0x00000044 32 write-only TXRDY Transmit Ready Interrupt Enable 0 1 write-only TXEMPTY Transmit Empty Interrupt Enable 1 1 write-only ENDTX End of Transmission Interrupt Enable 2 1 write-only TXBUFE Transmit Buffer Empty Interrupt Enable 3 1 write-only RXRDY Receive Ready Interrupt Enable 4 1 write-only OVRUN Receive Overrun Interrupt Enable 5 1 write-only ENDRX End of Reception Interrupt Enable 6 1 write-only RXBUFF Receive Buffer Full Interrupt Enable 7 1 write-only CP0 Compare 0 Interrupt Enable 8 1 write-only CP1 Compare 1 Interrupt Enable 9 1 write-only TXSYN Tx Sync Interrupt Enable 10 1 write-only RXSYN Rx Sync Interrupt Enable 11 1 write-only IDR Interrupt Disable Register 0x00000048 32 write-only TXRDY Transmit Ready Interrupt Disable 0 1 write-only TXEMPTY Transmit Empty Interrupt Disable 1 1 write-only ENDTX End of Transmission Interrupt Disable 2 1 write-only TXBUFE Transmit Buffer Empty Interrupt Disable 3 1 write-only RXRDY Receive Ready Interrupt Disable 4 1 write-only OVRUN Receive Overrun Interrupt Disable 5 1 write-only ENDRX End of Reception Interrupt Disable 6 1 write-only RXBUFF Receive Buffer Full Interrupt Disable 7 1 write-only CP0 Compare 0 Interrupt Disable 8 1 write-only CP1 Compare 1 Interrupt Disable 9 1 write-only TXSYN Tx Sync Interrupt Enable 10 1 write-only RXSYN Rx Sync Interrupt Enable 11 1 write-only IMR Interrupt Mask Register 0x0000004C 32 read-only 0x00000000 TXRDY Transmit Ready Interrupt Mask 0 1 read-only TXEMPTY Transmit Empty Interrupt Mask 1 1 read-only ENDTX End of Transmission Interrupt Mask 2 1 read-only TXBUFE Transmit Buffer Empty Interrupt Mask 3 1 read-only RXRDY Receive Ready Interrupt Mask 4 1 read-only OVRUN Receive Overrun Interrupt Mask 5 1 read-only ENDRX End of Reception Interrupt Mask 6 1 read-only RXBUFF Receive Buffer Full Interrupt Mask 7 1 read-only CP0 Compare 0 Interrupt Mask 8 1 read-only CP1 Compare 1 Interrupt Mask 9 1 read-only TXSYN Tx Sync Interrupt Mask 10 1 read-only RXSYN Rx Sync Interrupt Mask 11 1 read-only RPR Receive Pointer Register 0x00000100 32 read-write 0x00000000 RXPTR Receive Pointer Register 0 32 read-write RCR Receive Counter Register 0x00000104 32 read-write 0x00000000 RXCTR Receive Counter Register 0 16 read-write TPR Transmit Pointer Register 0x00000108 32 read-write 0x00000000 TXPTR Transmit Counter Register 0 32 read-write TCR Transmit Counter Register 0x0000010C 32 read-write 0x00000000 TXCTR Transmit Counter Register 0 16 read-write RNPR Receive Next Pointer Register 0x00000110 32 read-write 0x00000000 RXNPTR Receive Next Pointer 0 32 read-write RNCR Receive Next Counter Register 0x00000114 32 read-write 0x00000000 RXNCTR Receive Next Counter 0 16 read-write TNPR Transmit Next Pointer Register 0x00000118 32 read-write 0x00000000 TXNPTR Transmit Next Pointer 0 32 read-write TNCR Transmit Next Counter Register 0x0000011C 32 read-write 0x00000000 TXNCTR Transmit Counter Next 0 16 read-write PTCR Transfer Control Register 0x00000120 32 write-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 write-only RXTDIS Receiver Transfer Disable 1 1 write-only TXTEN Transmitter Transfer Enable 8 1 write-only TXTDIS Transmitter Transfer Disable 9 1 write-only PTSR Transfer Status Register 0x00000124 32 read-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 read-only TXTEN Transmitter Transfer Enable 8 1 read-only ISI 6141E Image Sensor Interface ISI_ 0xFFFC0000 0 0x4000 registers ISI 22 CR1 ISI Control 1 Register 0x00000000 32 read-write 0x00000002 ISI_RST Image sensor interface reset 0 1 read-write ISI_DIS Image sensor disable: 1 1 read-write HSYNC_POL Horizontal synchronization polarity 2 1 read-write VSYNC_POL Vertical synchronization polarity 3 1 read-write PIXCLK_POL Pixel clock polarity 4 1 read-write EMB_SYNC Embedded synchronization 6 1 read-write CRC_SYNC Embedded synchronization 7 1 read-write FRATE Frame rate [0..7] 8 3 read-write FULL Full mode is allowed 12 1 read-write THMASK Threshold mask 13 2 read-write CODEC_ON Enable the codec path enable bit 15 1 read-write SLD Start of Line Delay 16 8 read-write SFD Start of Frame Delay 24 8 read-write CR2 ISI Control 2 Register 0x00000004 32 read-write 0x00000000 IM_VSIZE Vertical size of the Image sensor [0..2047] 0 11 read-write GS_MODE 11 1 read-write RGB_MODE RGB input mode 12 1 read-write GRAYSCALE 13 1 read-write RGB_SWAP 14 1 read-write COL_SPACE Color space for the image data 15 1 read-write IM_HSIZE Horizontal size of the Image sensor [0..2047] 16 11 read-write YCC_SWAP Defines the YCC image data 28 2 read-write RGB_CFG Defines RGB pattern when RGB_MODE is set to 1 30 2 read-write SR ISI Status Register 0x00000008 32 read-only 0x00000000 SOF Start of frame 0 1 read-only DIS Image Sensor Interface disable 1 1 read-only SOFTRST Software reset 2 1 read-only CDC_PND Codec request pending 3 1 read-only CRC_ERR CRC synchronization error 4 1 read-only FO_C_OVF FIFO codec overflow 5 1 read-only FO_P_OVF FIFO preview overflow 6 1 read-only FO_P_EMP 7 1 read-only FO_C_EMP 8 1 read-only FR_OVR Frame rate overrun 9 1 read-only IER ISI Interrupt Enable Register 0x0000000C 32 read-write 0x00000000 SOF Start of Frame 0 1 read-write DIS Image Sensor Interface disable 1 1 read-write SOFTRST Soft Reset 2 1 read-write CRC_ERR CRC synchronization error 4 1 read-write FO_C_OVF FIFO codec Overflow 5 1 read-write FO_P_OVF FIFO preview Overflow 6 1 read-write FO_P_EMP 7 1 read-write FO_C_EMP 8 1 read-write FR_OVR Frame overrun 9 1 read-write IDR ISI Interrupt Disable Register 0x00000010 32 read-write 0x00000000 SOF Start of Frame 0 1 read-write DIS Image Sensor Interface disable 1 1 read-write SOFTRST 2 1 read-write CRC_ERR CRC synchronization error 4 1 read-write FO_C_OVF FIFO codec overflow 5 1 read-write FO_P_OVF FIFO preview overflow 6 1 read-write FO_P_EMP 7 1 read-write FO_C_EMP 8 1 read-write FR_OVR 9 1 read-write IMR ISI Interrupt Mask Register 0x00000014 32 read-write 0x00000000 SOF Start of Frame 0 1 read-write DIS Image sensor interface disable 1 1 read-write SOFTRST 2 1 read-write CRC_ERR CRC synchronization error 4 1 read-write FO_C_OVF FIFO codec overflow 5 1 read-write FO_P_OVF FIFO preview overflow 6 1 read-write FO_P_EMP 7 1 read-write FO_C_EMP 8 1 read-write FR_OVR Frame Rate Overrun 9 1 read-write PSIZE ISI Preview Size Register 0x00000020 32 read-write 0x00000000 PREV_VSIZE Vertical size for the preview path 0 10 read-write PREV_HSIZE Horizontal size for the preview path 16 10 read-write PDECF ISI Preview Decimation Factor Register 0x00000024 32 read-write 0x00000010 DEC_FACTOR Decimation factor 0 8 read-write PPFBD ISI Preview Primary FBD Register 0x00000028 32 read-write 0x00000000 PREV_FBD_ADDR Base address for preview frame buffer descriptor 0 32 read-write CDBA ISI Codec DMA Base Address Register 0x0000002C 32 read-write 0x00000000 CODEC_DMA_ADDR Base address for codec DMA 0 32 read-write Y2R_SET0 ISI CSC YCrCb To RGB Set 0 Register 0x00000030 32 read-write 0x6832CC95 C0 Color Space Conversion Matrix Coefficient C0 0 8 read-write C1 Color Space Conversion Matrix Coefficient C1 8 8 read-write C2 Color Space Conversion Matrix Coefficient C2 16 8 read-write C3 Color Space Conversion Matrix Coefficient C3 24 8 read-write Y2R_SET1 ISI CSC YCrCb To RGB Set 1 Register 0x00000034 32 read-write 0x00007102 C4 Color Space Conversion Matrix coefficient C4 0 9 read-write Yoff Color Space Conversion Luminance default offset 12 1 read-write Croff Color Space Conversion Red Chrominance default offset 13 1 read-write Cboff Color Space Conversion Blue Chrominance default offset 14 1 read-write R2Y_SET0 ISI CSC RGB To YCrCb Set 0 Register 0x00000038 32 read-write 0x01324145 C0 Color Space Conversion Matrix coefficient C0 0 8 read-write C1 Color Space Conversion Matrix coefficient C1 8 8 read-write C2 Color Space Conversion Matrix coefficient C2 16 8 read-write Roff Color Space Conversion Red component offset 24 1 read-write R2Y_SET1 ISI CSC RGB To YCrCb Set 1 Register 0x0000003C 32 read-write 0x01245E38 C3 Color Space Conversion Matrix coefficient C3 0 8 read-write C4 Color Space Conversion Matrix coefficient C4 8 8 read-write C5 Color Space Conversion Matrix coefficient C5 16 8 read-write Goff Color Space Conversion Green component offset 24 1 read-write R2Y_SET2 ISI CSC RGB To YCrCb Set 2 Register 0x00000040 32 read-write 0x01384A4B C6 Color Space Conversion Matrix coefficient C6 0 8 read-write C7 Color Space Conversion Matrix coefficient C7 8 8 read-write C8 Color Space Conversion Matrix coefficient C8 16 8 read-write Boff Color Space Conversion Blue component offset 24 1 read-write EMAC 6119I Ethernet MAC 10/100 EMAC_ 0xFFFC4000 0 0x4000 registers EMAC 21 NCR Network Control Register 0x00000000 32 read-write 0x00000000 LB LoopBack 0 1 read-write LLB Loopback local 1 1 read-write RE Receive enable 2 1 read-write TE Transmit enable 3 1 read-write MPE Management port enable 4 1 read-write CLRSTAT Clear statistics registers 5 1 read-write INCSTAT Increment statistics registers 6 1 read-write WESTAT Write enable for statistics registers 7 1 read-write BP Back pressure 8 1 read-write TSTART Start transmission 9 1 read-write THALT Transmit halt 10 1 read-write NCFGR Network Configuration Register 0x00000004 32 read-write 0x00000800 SPD Speed 0 1 read-write FD Full Duplex 1 1 read-write JFRAME Jumbo Frames 3 1 read-write CAF Copy All Frames 4 1 read-write NBC No Broadcast 5 1 read-write MTI Multicast Hash Enable 6 1 read-write UNI Unicast Hash Enable 7 1 read-write BIG Receive 1536 bytes frames 8 1 read-write CLK MDC clock divider 10 2 read-write MCK_8 MCK divided by 8 (MCK up to 20 MHz). 0x0 MCK_16 MCK divided by 16 (MCK up to 40 MHz). 0x1 MCK_32 MCK divided by 32 (MCK up to 80 MHz). 0x2 MCK_64 MCK divided by 64 (MCK up to 160 MHz). 0x3 RTY Retry test 12 1 read-write PAE Pause Enable 13 1 read-write RBOF Receive Buffer Offset 14 2 read-write OFFSET_0 No offset from start of receive buffer. 0x0 OFFSET_1 One-byte offset from start of receive buffer. 0x1 OFFSET_2 Two-byte offset from start of receive buffer. 0x2 OFFSET_3 Three-byte offset from start of receive buffer. 0x3 RLCE Receive Length field Checking Enable 16 1 read-write DRFCS Discard Receive FCS 17 1 read-write EFRHD 18 1 read-write IRXFCS Ignore RX FCS 19 1 read-write NSR Network Status Register 0x00000008 32 read-only MDIO 1 1 read-only IDLE 2 1 read-only TSR Transmit Status Register 0x00000014 32 read-write 0x00000000 UBR Used Bit Read 0 1 read-write COL Collision Occurred 1 1 read-write RLES Retry Limit exceeded 2 1 read-write TGO Transmit Go 3 1 read-write BEX Buffers exhausted mid frame 4 1 read-write COMP Transmit Complete 5 1 read-write UND Transmit Underrun 6 1 read-write RBQP Receive Buffer Queue Pointer Register 0x00000018 32 read-write 0x00000000 ADDR Receive buffer queue pointer address 2 30 read-write TBQP Transmit Buffer Queue Pointer Register 0x0000001C 32 read-write 0x00000000 ADDR Transmit buffer queue pointer address 2 30 read-write RSR Receive Status Register 0x00000020 32 read-write 0x00000000 BNA Buffer Not Available 0 1 read-write REC Frame Received 1 1 read-write OVR Receive Overrun 2 1 read-write ISR Interrupt Status Register 0x00000024 32 read-write 0x00000000 MFD Management Frame Done 0 1 read-write RCOMP Receive Complete 1 1 read-write RXUBR Receive Used Bit Read 2 1 read-write TXUBR Transmit Used Bit Read 3 1 read-write TUND Ethernet Transmit Buffer Underrun 4 1 read-write RLEX Retry Limit Exceeded 5 1 read-write TXERR Transmit Error 6 1 read-write TCOMP Transmit Complete 7 1 read-write ROVR Receive Overrun 10 1 read-write HRESP Hresp not OK 11 1 read-write PFRE Pause Frame Received 12 1 read-write PTZ Pause Time Zero 13 1 read-write IER Interrupt Enable Register 0x00000028 32 write-only MFD Management Frame sent 0 1 write-only RCOMP Receive Complete 1 1 write-only RXUBR Receive Used Bit Read 2 1 write-only TXUBR Transmit Used Bit Read 3 1 write-only TUND Ethernet Transmit Buffer Underrun 4 1 write-only RLE Retry Limit Exceeded 5 1 write-only TXERR 6 1 write-only TCOMP Transmit Complete 7 1 write-only ROVR Receive Overrun 10 1 write-only HRESP Hresp not OK 11 1 write-only PFR Pause Frame Received 12 1 write-only PTZ Pause Time Zero 13 1 write-only IDR Interrupt Disable Register 0x0000002C 32 write-only MFD Management Frame sent 0 1 write-only RCOMP Receive Complete 1 1 write-only RXUBR Receive Used Bit Read 2 1 write-only TXUBR Transmit Used Bit Read 3 1 write-only TUND Ethernet Transmit Buffer Underrun 4 1 write-only RLE Retry Limit Exceeded 5 1 write-only TXERR 6 1 write-only TCOMP Transmit Complete 7 1 write-only ROVR Receive Overrun 10 1 write-only HRESP Hresp not OK 11 1 write-only PFR Pause Frame Received 12 1 write-only PTZ Pause Time Zero 13 1 write-only IMR Interrupt Mask Register 0x00000030 32 read-only 0x00003FFF MFD Management Frame sent 0 1 read-only RCOMP Receive Complete 1 1 read-only RXUBR Receive Used Bit Read 2 1 read-only TXUBR Transmit Used Bit Read 3 1 read-only TUND Ethernet Transmit Buffer Underrun 4 1 read-only RLE Retry Limit Exceeded 5 1 read-only TXERR 6 1 read-only TCOMP Transmit Complete 7 1 read-only ROVR Receive Overrun 10 1 read-only HRESP Hresp not OK 11 1 read-only PFR Pause Frame Received 12 1 read-only PTZ Pause Time Zero 13 1 read-only MAN Phy Maintenance Register 0x00000034 32 read-write 0x00000000 DATA 0 16 read-write CODE 16 2 read-write REGA Register Address 18 5 read-write PHYA PHY Address 23 5 read-write RW Read-write 28 2 read-write SOF Start of frame 30 2 read-write PTR Pause Time Register 0x00000038 32 read-write 0x00000000 PTIME Pause Time 0 16 read-write PFR Pause Frames Received Register 0x0000003C 32 read-write 0x00000000 FROK Pause Frames received OK 0 16 read-write FTO Frames Transmitted Ok Register 0x00000040 32 read-write 0x00000000 FTOK Frames Transmitted OK 0 24 read-write SCF Single Collision Frames Register 0x00000044 32 read-write 0x00000000 SCF Single Collision Frames 0 16 read-write MCF Multiple Collision Frames Register 0x00000048 32 read-write 0x00000000 MCF Multicollision Frames 0 16 read-write FRO Frames Received Ok Register 0x0000004C 32 read-write 0x00000000 FROK Frames Received OK 0 24 read-write FCSE Frame Check Sequence Errors Register 0x00000050 32 read-write 0x00000000 FCSE Frame Check Sequence Errors 0 8 read-write ALE Alignment Errors Register 0x00000054 32 read-write 0x00000000 ALE Alignment Errors 0 8 read-write DTF Deferred Transmission Frames Register 0x00000058 32 read-write 0x00000000 DTF Deferred Transmission Frames 0 16 read-write LCOL Late Collisions Register 0x0000005C 32 read-write 0x00000000 LCOL Late Collisions 0 8 read-write ECOL Excessive Collisions Register 0x00000060 32 read-write 0x00000000 EXCOL Excessive Collisions 0 8 read-write TUND Transmit Underrun Errors Register 0x00000064 32 read-write 0x00000000 TUND Transmit Underruns 0 8 read-write CSE Carrier Sense Errors Register 0x00000068 32 read-write 0x00000000 CSE Carrier Sense Errors 0 8 read-write RRE Receive Resource Errors Register 0x0000006C 32 read-write 0x00000000 RRE Receive Resource Errors 0 16 read-write ROV Receive Overrun Errors Register 0x00000070 32 read-write 0x00000000 ROVR Receive Overrun 0 8 read-write RSE Receive Symbol Errors Register 0x00000074 32 read-write 0x00000000 RSE Receive Symbol Errors 0 8 read-write ELE Excessive Length Errors Register 0x00000078 32 read-write 0x00000000 EXL Excessive Length Errors 0 8 read-write RJA Receive Jabbers Register 0x0000007C 32 read-write 0x00000000 RJB Receive Jabbers 0 8 read-write USF Undersize Frames Register 0x00000080 32 read-write 0x00000000 USF Undersize frames 0 8 read-write STE SQE Test Errors Register 0x00000084 32 read-write 0x00000000 SQER SQE test errors 0 8 read-write RLE Received Length Field Mismatch Register 0x00000088 32 read-write 0x00000000 RLFM Receive Length Field Mismatch 0 8 read-write HRB Hash Register Bottom [31:0] Register 0x00000090 32 read-write 0x00000000 ADDR 0 32 read-write HRT Hash Register Top [63:32] Register 0x00000094 32 read-write 0x00000000 ADDR 0 32 read-write SA1B Specific Address 1 Bottom Register 0x00000098 32 read-write 0x00000000 ADDR 0 32 read-write SA1T Specific Address 1 Top Register 0x0000009C 32 read-write 0x00000000 ADDR 0 16 read-write SA2B Specific Address 2 Bottom Register 0x000000A0 32 read-write 0x00000000 ADDR 0 32 read-write SA2T Specific Address 2 Top Register 0x000000A4 32 read-write 0x00000000 ADDR 0 16 read-write SA3B Specific Address 3 Bottom Register 0x000000A8 32 read-write 0x00000000 ADDR 0 32 read-write SA3T Specific Address 3 Top Register 0x000000AC 32 read-write 0x00000000 ADDR 0 16 read-write SA4B Specific Address 4 Bottom Register 0x000000B0 32 read-write 0x00000000 ADDR 0 32 read-write SA4T Specific Address 4 Top Register 0x000000B4 32 read-write 0x00000000 ADDR 0 16 read-write TID Type ID Checking Register 0x000000B8 32 read-write 0x00000000 TID Type ID checking 0 16 read-write USRIO User Input/Output Register 0x000000C0 32 read-write 0x00000000 RMII Reduce MII 0 1 read-write CLKEN Clock Enable 1 1 read-write SPI0 6088T Serial Peripheral Interface 0 SPI SPI0_ 0xFFFC8000 0 0x4000 registers SPI0 12 CR Control Register 0x00000000 32 write-only SPIEN SPI Enable 0 1 write-only SPIDIS SPI Disable 1 1 write-only SWRST SPI Software Reset 7 1 write-only LASTXFER Last Transfer 24 1 write-only MR Mode Register 0x00000004 32 read-write 0x00000000 MSTR Master/Slave Mode 0 1 read-write PS Peripheral Select 1 1 read-write PCSDEC Chip Select Decode 2 1 read-write MODFDIS Mode Fault Detection 4 1 read-write WDRBT Wait Data Read Before Transfer 5 1 read-write LLB Local Loopback Enable 7 1 read-write PCS Peripheral Chip Select 16 4 read-write DLYBCS Delay Between Chip Selects 24 8 read-write RDR Receive Data Register 0x00000008 32 read-only 0x00000000 RD Receive Data 0 16 read-only PCS Peripheral Chip Select 16 4 read-only TDR Transmit Data Register 0x0000000C 32 write-only TD Transmit Data 0 16 write-only PCS Peripheral Chip Select 16 4 write-only LASTXFER Last Transfer 24 1 write-only SR Status Register 0x00000010 32 read-only 0x000000F0 RDRF Receive Data Register Full 0 1 read-only TDRE Transmit Data Register Empty 1 1 read-only MODF Mode Fault Error 2 1 read-only OVRES Overrun Error Status 3 1 read-only NSSR NSS Rising 8 1 read-only TXEMPTY Transmission Registers Empty 9 1 read-only SPIENS SPI Enable Status 16 1 read-only IER Interrupt Enable Register 0x00000014 32 write-only RDRF Receive Data Register Full Interrupt Enable 0 1 write-only TDRE SPI Transmit Data Register Empty Interrupt Enable 1 1 write-only MODF Mode Fault Error Interrupt Enable 2 1 write-only OVRES Overrun Error Interrupt Enable 3 1 write-only NSSR NSS Rising Interrupt Enable 8 1 write-only TXEMPTY Transmission Registers Empty Enable 9 1 write-only IDR Interrupt Disable Register 0x00000018 32 write-only RDRF Receive Data Register Full Interrupt Disable 0 1 write-only TDRE SPI Transmit Data Register Empty Interrupt Disable 1 1 write-only MODF Mode Fault Error Interrupt Disable 2 1 write-only OVRES Overrun Error Interrupt Disable 3 1 write-only NSSR NSS Rising Interrupt Disable 8 1 write-only TXEMPTY Transmission Registers Empty Disable 9 1 write-only IMR Interrupt Mask Register 0x0000001C 32 read-only 0x00000000 RDRF Receive Data Register Full Interrupt Mask 0 1 read-only TDRE SPI Transmit Data Register Empty Interrupt Mask 1 1 read-only MODF Mode Fault Error Interrupt Mask 2 1 read-only OVRES Overrun Error Interrupt Mask 3 1 read-only NSSR NSS Rising Interrupt Mask 8 1 read-only TXEMPTY Transmission Registers Empty Mask 9 1 read-only 4 4 0-3 CSR[%s] Chip Select Register 0x00000030 32 read-write CPOL Clock Polarity 0 1 read-write NCPHA Clock Phase 1 1 read-write CSAAT Chip Select Active After Transfer 3 1 read-write BITS Bits Per Transfer 4 4 read-write 8_BIT 8 bits for transfer 0x0 9_BIT 9 bits for transfer 0x1 10_BIT 10 bits for transfer 0x2 11_BIT 11 bits for transfer 0x3 12_BIT 12 bits for transfer 0x4 13_BIT 13 bits for transfer 0x5 14_BIT 14 bits for transfer 0x6 15_BIT 15 bits for transfer 0x7 16_BIT 16 bits for transfer 0x8 SCBR Serial Clock Baud Rate 8 8 read-write DLYBS Delay Before SPCK 16 8 read-write DLYBCT Delay Between Consecutive Transfers 24 8 read-write WPMR Write Protection Control Register 0x000000E4 32 read-write 0x00000000 WPEN Write Protection Enable 0 1 read-write WPKEY Write Protection Key Password 8 24 read-write WPSR Write Protection Status Register 0x000000E8 32 read-only 0x00000000 WPVS Write Protection Violation Status 0 1 read-only WPVSRC Write Protection Violation Source 8 8 read-only RPR Receive Pointer Register 0x00000100 32 read-write 0x00000000 RXPTR Receive Pointer Register 0 32 read-write RCR Receive Counter Register 0x00000104 32 read-write 0x00000000 RXCTR Receive Counter Register 0 16 read-write TPR Transmit Pointer Register 0x00000108 32 read-write 0x00000000 TXPTR Transmit Counter Register 0 32 read-write TCR Transmit Counter Register 0x0000010C 32 read-write 0x00000000 TXCTR Transmit Counter Register 0 16 read-write RNPR Receive Next Pointer Register 0x00000110 32 read-write 0x00000000 RXNPTR Receive Next Pointer 0 32 read-write RNCR Receive Next Counter Register 0x00000114 32 read-write 0x00000000 RXNCTR Receive Next Counter 0 16 read-write TNPR Transmit Next Pointer Register 0x00000118 32 read-write 0x00000000 TXNPTR Transmit Next Pointer 0 32 read-write TNCR Transmit Next Counter Register 0x0000011C 32 read-write 0x00000000 TXNCTR Transmit Counter Next 0 16 read-write PTCR Transfer Control Register 0x00000120 32 write-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 write-only RXTDIS Receiver Transfer Disable 1 1 write-only TXTEN Transmitter Transfer Enable 8 1 write-only TXTDIS Transmitter Transfer Disable 9 1 write-only PTSR Transfer Status Register 0x00000124 32 read-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 read-only TXTEN Transmitter Transfer Enable 8 1 read-only SPI1 6088T Serial Peripheral Interface 1 SPI SPI1_ 0xFFFCC000 0 0x4000 registers SPI1 13 CR Control Register 0x00000000 32 write-only SPIEN SPI Enable 0 1 write-only SPIDIS SPI Disable 1 1 write-only SWRST SPI Software Reset 7 1 write-only LASTXFER Last Transfer 24 1 write-only MR Mode Register 0x00000004 32 read-write 0x00000000 MSTR Master/Slave Mode 0 1 read-write PS Peripheral Select 1 1 read-write PCSDEC Chip Select Decode 2 1 read-write MODFDIS Mode Fault Detection 4 1 read-write WDRBT Wait Data Read Before Transfer 5 1 read-write LLB Local Loopback Enable 7 1 read-write PCS Peripheral Chip Select 16 4 read-write DLYBCS Delay Between Chip Selects 24 8 read-write RDR Receive Data Register 0x00000008 32 read-only 0x00000000 RD Receive Data 0 16 read-only PCS Peripheral Chip Select 16 4 read-only TDR Transmit Data Register 0x0000000C 32 write-only TD Transmit Data 0 16 write-only PCS Peripheral Chip Select 16 4 write-only LASTXFER Last Transfer 24 1 write-only SR Status Register 0x00000010 32 read-only 0x000000F0 RDRF Receive Data Register Full 0 1 read-only TDRE Transmit Data Register Empty 1 1 read-only MODF Mode Fault Error 2 1 read-only OVRES Overrun Error Status 3 1 read-only NSSR NSS Rising 8 1 read-only TXEMPTY Transmission Registers Empty 9 1 read-only SPIENS SPI Enable Status 16 1 read-only IER Interrupt Enable Register 0x00000014 32 write-only RDRF Receive Data Register Full Interrupt Enable 0 1 write-only TDRE SPI Transmit Data Register Empty Interrupt Enable 1 1 write-only MODF Mode Fault Error Interrupt Enable 2 1 write-only OVRES Overrun Error Interrupt Enable 3 1 write-only NSSR NSS Rising Interrupt Enable 8 1 write-only TXEMPTY Transmission Registers Empty Enable 9 1 write-only IDR Interrupt Disable Register 0x00000018 32 write-only RDRF Receive Data Register Full Interrupt Disable 0 1 write-only TDRE SPI Transmit Data Register Empty Interrupt Disable 1 1 write-only MODF Mode Fault Error Interrupt Disable 2 1 write-only OVRES Overrun Error Interrupt Disable 3 1 write-only NSSR NSS Rising Interrupt Disable 8 1 write-only TXEMPTY Transmission Registers Empty Disable 9 1 write-only IMR Interrupt Mask Register 0x0000001C 32 read-only 0x00000000 RDRF Receive Data Register Full Interrupt Mask 0 1 read-only TDRE SPI Transmit Data Register Empty Interrupt Mask 1 1 read-only MODF Mode Fault Error Interrupt Mask 2 1 read-only OVRES Overrun Error Interrupt Mask 3 1 read-only NSSR NSS Rising Interrupt Mask 8 1 read-only TXEMPTY Transmission Registers Empty Mask 9 1 read-only 4 4 0-3 CSR[%s] Chip Select Register 0x00000030 32 read-write CPOL Clock Polarity 0 1 read-write NCPHA Clock Phase 1 1 read-write CSAAT Chip Select Active After Transfer 3 1 read-write BITS Bits Per Transfer 4 4 read-write 8_BIT 8 bits for transfer 0x0 9_BIT 9 bits for transfer 0x1 10_BIT 10 bits for transfer 0x2 11_BIT 11 bits for transfer 0x3 12_BIT 12 bits for transfer 0x4 13_BIT 13 bits for transfer 0x5 14_BIT 14 bits for transfer 0x6 15_BIT 15 bits for transfer 0x7 16_BIT 16 bits for transfer 0x8 SCBR Serial Clock Baud Rate 8 8 read-write DLYBS Delay Before SPCK 16 8 read-write DLYBCT Delay Between Consecutive Transfers 24 8 read-write WPMR Write Protection Control Register 0x000000E4 32 read-write 0x00000000 WPEN Write Protection Enable 0 1 read-write WPKEY Write Protection Key Password 8 24 read-write WPSR Write Protection Status Register 0x000000E8 32 read-only 0x00000000 WPVS Write Protection Violation Status 0 1 read-only WPVSRC Write Protection Violation Source 8 8 read-only RPR Receive Pointer Register 0x00000100 32 read-write 0x00000000 RXPTR Receive Pointer Register 0 32 read-write RCR Receive Counter Register 0x00000104 32 read-write 0x00000000 RXCTR Receive Counter Register 0 16 read-write TPR Transmit Pointer Register 0x00000108 32 read-write 0x00000000 TXPTR Transmit Counter Register 0 32 read-write TCR Transmit Counter Register 0x0000010C 32 read-write 0x00000000 TXCTR Transmit Counter Register 0 16 read-write RNPR Receive Next Pointer Register 0x00000110 32 read-write 0x00000000 RXNPTR Receive Next Pointer 0 32 read-write RNCR Receive Next Counter Register 0x00000114 32 read-write 0x00000000 RXNCTR Receive Next Counter 0 16 read-write TNPR Transmit Next Pointer Register 0x00000118 32 read-write 0x00000000 TXNPTR Transmit Next Pointer 0 32 read-write TNCR Transmit Next Counter Register 0x0000011C 32 read-write 0x00000000 TXNCTR Transmit Counter Next 0 16 read-write PTCR Transfer Control Register 0x00000120 32 write-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 write-only RXTDIS Receiver Transfer Disable 1 1 write-only TXTEN Transmitter Transfer Enable 8 1 write-only TXTDIS Transmitter Transfer Disable 9 1 write-only PTSR Transfer Status Register 0x00000124 32 read-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 read-only TXTEN Transmitter Transfer Enable 8 1 read-only USART3 6089V Universal Synchronous Asynchronous Receiver Transmitter 3 USART USART3_ 0xFFFD0000 0 0x4000 registers USART3 23 CR Control Register 0x00000000 32 write-only RSTRX Reset Receiver 2 1 write-only RSTTX Reset Transmitter 3 1 write-only RXEN Receiver Enable 4 1 write-only RXDIS Receiver Disable 5 1 write-only TXEN Transmitter Enable 6 1 write-only TXDIS Transmitter Disable 7 1 write-only RSTSTA Reset Status Bits 8 1 write-only STTBRK Start Break 9 1 write-only STPBRK Stop Break 10 1 write-only STTTO Start Time-out 11 1 write-only SENDA Send Address 12 1 write-only RSTIT Reset Iterations 13 1 write-only RSTNACK Reset Non Acknowledge 14 1 write-only RETTO Rearm Time-out 15 1 write-only DTREN Data Terminal Ready Enable 16 1 write-only DTRDIS Data Terminal Ready Disable 17 1 write-only RTSEN Request to Send Enable 18 1 write-only RTSDIS Request to Send Disable 19 1 write-only MR Mode Register 0x00000004 32 read-write USART_MODE 0 4 read-write NORMAL Normal mode 0x0 RS485 RS485 0x1 HW_HANDSHAKING Hardware Handshaking 0x2 MODEM Modem 0x3 IS07816_T_0 IS07816 Protocol: T = 0 0x4 IS07816_T_1 IS07816 Protocol: T = 1 0x6 IRDA IrDA 0x8 USCLKS Clock Selection 4 2 read-write MCK Master Clock MCK is selected 0x0 DIV Internal Clock Divided MCK/DIV (DIV=8) is selected 0x1 SCK Serial Clock SLK is selected 0x3 CHRL Character Length. 6 2 read-write 5_BIT Character length is 5 bits 0x0 6_BIT Character length is 6 bits 0x1 7_BIT Character length is 7 bits 0x2 8_BIT Character length is 8 bits 0x3 SYNC Synchronous Mode Select 8 1 read-write PAR Parity Type 9 3 read-write EVEN Even parity 0x0 ODD Odd parity 0x1 SPACE Parity forced to 0 (Space) 0x2 MARK Parity forced to 1 (Mark) 0x3 NO No parity 0x4 MULTIDROP Multidrop mode 0x6 NBSTOP Number of Stop Bits 12 2 read-write 1_BIT 1 stop bit 0x0 1_5_BIT 1.5 stop bit (SYNC = 0) or reserved (SYNC = 1) 0x1 2_BIT 2 stop bits 0x2 CHMODE Channel Mode 14 2 read-write NORMAL Normal Mode 0x0 AUTOMATIC Automatic Echo. Receiver input is connected to the TXD pin. 0x1 LOCAL_LOOPBACK Local Loopback. Transmitter output is connected to the Receiver Input. 0x2 REMOTE_LOOPBACK Remote Loopback. RXD pin is internally connected to the TXD pin. 0x3 MSBF Bit Order 16 1 read-write MODE9 9-bit Character Length 17 1 read-write CLKO Clock Output Select 18 1 read-write OVER Oversampling Mode 19 1 read-write INACK Inhibit Non Acknowledge 20 1 read-write DSNACK Disable Successive NACK 21 1 read-write VAR_SYNC Variable Synchronization of Command/Data Sync Start Frame Delimiter 22 1 read-write MAX_ITERATION 24 3 read-write FILTER Infrared Receive Line Filter 28 1 read-write MAN Manchester Encoder/Decoder Enable 29 1 read-write MODSYNC Manchester Synchronization Mode 30 1 read-write ONEBIT Start Frame Delimiter Selector 31 1 read-write IER Interrupt Enable Register 0x00000008 32 write-only RXRDY RXRDY Interrupt Enable 0 1 write-only TXRDY TXRDY Interrupt Enable 1 1 write-only RXBRK Receiver Break Interrupt Enable 2 1 write-only ENDRX End of Receive Transfer Interrupt Enable 3 1 write-only ENDTX End of Transmit Interrupt Enable 4 1 write-only OVRE Overrun Error Interrupt Enable 5 1 write-only FRAME Framing Error Interrupt Enable 6 1 write-only PARE Parity Error Interrupt Enable 7 1 write-only TIMEOUT Time-out Interrupt Enable 8 1 write-only TXEMPTY TXEMPTY Interrupt Enable 9 1 write-only ITER Max number of Repetitions Reached 10 1 write-only TXBUFE Buffer Empty Interrupt Enable 11 1 write-only RXBUFF Buffer Full Interrupt Enable 12 1 write-only NACK Non AcknowledgeInterrupt Enable 13 1 write-only RIIC Ring Indicator Input Change Enable 16 1 write-only DSRIC Data Set Ready Input Change Enable 17 1 write-only DCDIC Data Carrier Detect Input Change Interrupt Enable 18 1 write-only CTSIC Clear to Send Input Change Interrupt Enable 19 1 write-only MANE Manchester Error Interrupt Enable 24 1 write-only IDR Interrupt Disable Register 0x0000000C 32 write-only RXRDY RXRDY Interrupt Disable 0 1 write-only TXRDY TXRDY Interrupt Disable 1 1 write-only RXBRK Receiver Break Interrupt Disable 2 1 write-only ENDRX End of Receive Transfer Interrupt Disable 3 1 write-only ENDTX End of Transmit Interrupt Disable 4 1 write-only OVRE Overrun Error Interrupt Disable 5 1 write-only FRAME Framing Error Interrupt Disable 6 1 write-only PARE Parity Error Interrupt Disable 7 1 write-only TIMEOUT Time-out Interrupt Disable 8 1 write-only TXEMPTY TXEMPTY Interrupt Disable 9 1 write-only ITER Max number of Repetitions Reached Disable 10 1 write-only TXBUFE Buffer Empty Interrupt Disable 11 1 write-only RXBUFF Buffer Full Interrupt Disable 12 1 write-only NACK Non AcknowledgeInterrupt Disable 13 1 write-only RIIC Ring Indicator Input Change Disable 16 1 write-only DSRIC Data Set Ready Input Change Disable 17 1 write-only DCDIC Data Carrier Detect Input Change Interrupt Disable 18 1 write-only CTSIC Clear to Send Input Change Interrupt Disable 19 1 write-only MANE Manchester Error Interrupt Disable 24 1 write-only IMR Interrupt Mask Register 0x00000010 32 read-only 0x00000000 RXRDY RXRDY Interrupt Mask 0 1 read-only TXRDY TXRDY Interrupt Mask 1 1 read-only RXBRK Receiver Break Interrupt Mask 2 1 read-only ENDRX End of Receive Transfer Interrupt Mask 3 1 read-only ENDTX End of Transmit Interrupt Mask 4 1 read-only OVRE Overrun Error Interrupt Mask 5 1 read-only FRAME Framing Error Interrupt Mask 6 1 read-only PARE Parity Error Interrupt Mask 7 1 read-only TIMEOUT Time-out Interrupt Mask 8 1 read-only TXEMPTY TXEMPTY Interrupt Mask 9 1 read-only ITER Max number of Repetitions Reached Mask 10 1 read-only TXBUFE Buffer Empty Interrupt Mask 11 1 read-only RXBUFF Buffer Full Interrupt Mask 12 1 read-only NACK Non AcknowledgeInterrupt Mask 13 1 read-only RIIC Ring Indicator Input Change Mask 16 1 read-only DSRIC Data Set Ready Input Change Mask 17 1 read-only DCDIC Data Carrier Detect Input Change Interrupt Mask 18 1 read-only CTSIC Clear to Send Input Change Interrupt Mask 19 1 read-only MANE Manchester Error Interrupt Mask 24 1 read-only CSR Channel Status Register 0x00000014 32 read-only RXRDY Receiver Ready 0 1 read-only TXRDY Transmitter Ready 1 1 read-only RXBRK Break Received/End of Break 2 1 read-only ENDRX End of Receiver Transfer 3 1 read-only ENDTX End of Transmitter Transfer 4 1 read-only OVRE Overrun Error 5 1 read-only FRAME Framing Error 6 1 read-only PARE Parity Error 7 1 read-only TIMEOUT Receiver Time-out 8 1 read-only TXEMPTY Transmitter Empty 9 1 read-only ITER Max number of Repetitions Reached 10 1 read-only TXBUFE Transmission Buffer Empty 11 1 read-only RXBUFF Reception Buffer Full 12 1 read-only NACK Non AcknowledgeInterrupt 13 1 read-only RIIC Ring Indicator Input Change Flag 16 1 read-only DSRIC Data Set Ready Input Change Flag 17 1 read-only DCDIC Data Carrier Detect Input Change Flag 18 1 read-only CTSIC Clear to Send Input Change Flag 19 1 read-only RI Image of RI Input 20 1 read-only DSR Image of DSR Input 21 1 read-only DCD Image of DCD Input 22 1 read-only CTS Image of CTS Input 23 1 read-only MANERR Manchester Error 24 1 read-only RHR Receiver Holding Register 0x00000018 32 read-only 0x00000000 RXCHR Received Character 0 9 read-only RXSYNH Received Sync 15 1 read-only THR Transmitter Holding Register 0x0000001C 32 write-only TXCHR Character to be Transmitted 0 9 write-only TXSYNH Sync Field to be transmitted 15 1 write-only BRGR Baud Rate Generator Register 0x00000020 32 read-write 0x00000000 CD Clock Divider 0 16 read-write FP Fractional Part 16 3 read-write RTOR Receiver Time-out Register 0x00000024 32 read-write 0x00000000 TO Time-out Value 0 16 read-write TTGR Transmitter Timeguard Register 0x00000028 32 read-write 0x00000000 TG Timeguard Value 0 8 read-write FIDI FI DI Ratio Register 0x00000040 32 read-write 0x00000174 FI_DI_RATIO FI Over DI Ratio Value 0 11 read-write NER Number of Errors Register 0x00000044 32 read-only NB_ERRORS Number of Errors 0 8 read-only IF IrDA Filter Register 0x0000004C 32 read-write 0x00000000 IRDA_FILTER IrDA Filter 0 8 read-write MAN Manchester Encoder Decoder Register 0x00000050 32 read-write 0x30011004 TX_PL Transmitter Preamble Length 0 4 read-write TX_PP Transmitter Preamble Pattern 8 2 read-write ALL_ONE The preamble is composed of '1's 0x0 ALL_ZERO The preamble is composed of '0's 0x1 ZERO_ONE The preamble is composed of '01's 0x2 ONE_ZERO The preamble is composed of '10's 0x3 TX_MPOL Transmitter Manchester Polarity 12 1 read-write RX_PL Receiver Preamble Length 16 4 read-write RX_PP Receiver Preamble Pattern detected 24 2 read-write ALL_ONE The preamble is composed of '1's 0x0 ALL_ZERO The preamble is composed of '0's 0x1 ZERO_ONE The preamble is composed of '01's 0x2 ONE_ZERO The preamble is composed of '10's 0x3 RX_MPOL Receiver Manchester Polarity 28 1 read-write STUCKTO1 29 1 read-write DRIFT Drift compensation 30 1 read-write RPR Receive Pointer Register 0x00000100 32 read-write 0x00000000 RXPTR Receive Pointer Register 0 32 read-write RCR Receive Counter Register 0x00000104 32 read-write 0x00000000 RXCTR Receive Counter Register 0 16 read-write TPR Transmit Pointer Register 0x00000108 32 read-write 0x00000000 TXPTR Transmit Counter Register 0 32 read-write TCR Transmit Counter Register 0x0000010C 32 read-write 0x00000000 TXCTR Transmit Counter Register 0 16 read-write RNPR Receive Next Pointer Register 0x00000110 32 read-write 0x00000000 RXNPTR Receive Next Pointer 0 32 read-write RNCR Receive Next Counter Register 0x00000114 32 read-write 0x00000000 RXNCTR Receive Next Counter 0 16 read-write TNPR Transmit Next Pointer Register 0x00000118 32 read-write 0x00000000 TXNPTR Transmit Next Pointer 0 32 read-write TNCR Transmit Next Counter Register 0x0000011C 32 read-write 0x00000000 TXNCTR Transmit Counter Next 0 16 read-write PTCR Transfer Control Register 0x00000120 32 write-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 write-only RXTDIS Receiver Transfer Disable 1 1 write-only TXTEN Transmitter Transfer Enable 8 1 write-only TXTDIS Transmitter Transfer Disable 9 1 write-only PTSR Transfer Status Register 0x00000124 32 read-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 read-only TXTEN Transmitter Transfer Enable 8 1 read-only USART4 6089V Universal Synchronous Asynchronous Receiver Transmitter 4 USART USART4_ 0xFFFD4000 0 0x4000 registers USART4 24 CR Control Register 0x00000000 32 write-only RSTRX Reset Receiver 2 1 write-only RSTTX Reset Transmitter 3 1 write-only RXEN Receiver Enable 4 1 write-only RXDIS Receiver Disable 5 1 write-only TXEN Transmitter Enable 6 1 write-only TXDIS Transmitter Disable 7 1 write-only RSTSTA Reset Status Bits 8 1 write-only STTBRK Start Break 9 1 write-only STPBRK Stop Break 10 1 write-only STTTO Start Time-out 11 1 write-only SENDA Send Address 12 1 write-only RSTIT Reset Iterations 13 1 write-only RSTNACK Reset Non Acknowledge 14 1 write-only RETTO Rearm Time-out 15 1 write-only DTREN Data Terminal Ready Enable 16 1 write-only DTRDIS Data Terminal Ready Disable 17 1 write-only RTSEN Request to Send Enable 18 1 write-only RTSDIS Request to Send Disable 19 1 write-only MR Mode Register 0x00000004 32 read-write USART_MODE 0 4 read-write NORMAL Normal mode 0x0 RS485 RS485 0x1 HW_HANDSHAKING Hardware Handshaking 0x2 MODEM Modem 0x3 IS07816_T_0 IS07816 Protocol: T = 0 0x4 IS07816_T_1 IS07816 Protocol: T = 1 0x6 IRDA IrDA 0x8 USCLKS Clock Selection 4 2 read-write MCK Master Clock MCK is selected 0x0 DIV Internal Clock Divided MCK/DIV (DIV=8) is selected 0x1 SCK Serial Clock SLK is selected 0x3 CHRL Character Length. 6 2 read-write 5_BIT Character length is 5 bits 0x0 6_BIT Character length is 6 bits 0x1 7_BIT Character length is 7 bits 0x2 8_BIT Character length is 8 bits 0x3 SYNC Synchronous Mode Select 8 1 read-write PAR Parity Type 9 3 read-write EVEN Even parity 0x0 ODD Odd parity 0x1 SPACE Parity forced to 0 (Space) 0x2 MARK Parity forced to 1 (Mark) 0x3 NO No parity 0x4 MULTIDROP Multidrop mode 0x6 NBSTOP Number of Stop Bits 12 2 read-write 1_BIT 1 stop bit 0x0 1_5_BIT 1.5 stop bit (SYNC = 0) or reserved (SYNC = 1) 0x1 2_BIT 2 stop bits 0x2 CHMODE Channel Mode 14 2 read-write NORMAL Normal Mode 0x0 AUTOMATIC Automatic Echo. Receiver input is connected to the TXD pin. 0x1 LOCAL_LOOPBACK Local Loopback. Transmitter output is connected to the Receiver Input. 0x2 REMOTE_LOOPBACK Remote Loopback. RXD pin is internally connected to the TXD pin. 0x3 MSBF Bit Order 16 1 read-write MODE9 9-bit Character Length 17 1 read-write CLKO Clock Output Select 18 1 read-write OVER Oversampling Mode 19 1 read-write INACK Inhibit Non Acknowledge 20 1 read-write DSNACK Disable Successive NACK 21 1 read-write VAR_SYNC Variable Synchronization of Command/Data Sync Start Frame Delimiter 22 1 read-write MAX_ITERATION 24 3 read-write FILTER Infrared Receive Line Filter 28 1 read-write MAN Manchester Encoder/Decoder Enable 29 1 read-write MODSYNC Manchester Synchronization Mode 30 1 read-write ONEBIT Start Frame Delimiter Selector 31 1 read-write IER Interrupt Enable Register 0x00000008 32 write-only RXRDY RXRDY Interrupt Enable 0 1 write-only TXRDY TXRDY Interrupt Enable 1 1 write-only RXBRK Receiver Break Interrupt Enable 2 1 write-only ENDRX End of Receive Transfer Interrupt Enable 3 1 write-only ENDTX End of Transmit Interrupt Enable 4 1 write-only OVRE Overrun Error Interrupt Enable 5 1 write-only FRAME Framing Error Interrupt Enable 6 1 write-only PARE Parity Error Interrupt Enable 7 1 write-only TIMEOUT Time-out Interrupt Enable 8 1 write-only TXEMPTY TXEMPTY Interrupt Enable 9 1 write-only ITER Max number of Repetitions Reached 10 1 write-only TXBUFE Buffer Empty Interrupt Enable 11 1 write-only RXBUFF Buffer Full Interrupt Enable 12 1 write-only NACK Non AcknowledgeInterrupt Enable 13 1 write-only RIIC Ring Indicator Input Change Enable 16 1 write-only DSRIC Data Set Ready Input Change Enable 17 1 write-only DCDIC Data Carrier Detect Input Change Interrupt Enable 18 1 write-only CTSIC Clear to Send Input Change Interrupt Enable 19 1 write-only MANE Manchester Error Interrupt Enable 24 1 write-only IDR Interrupt Disable Register 0x0000000C 32 write-only RXRDY RXRDY Interrupt Disable 0 1 write-only TXRDY TXRDY Interrupt Disable 1 1 write-only RXBRK Receiver Break Interrupt Disable 2 1 write-only ENDRX End of Receive Transfer Interrupt Disable 3 1 write-only ENDTX End of Transmit Interrupt Disable 4 1 write-only OVRE Overrun Error Interrupt Disable 5 1 write-only FRAME Framing Error Interrupt Disable 6 1 write-only PARE Parity Error Interrupt Disable 7 1 write-only TIMEOUT Time-out Interrupt Disable 8 1 write-only TXEMPTY TXEMPTY Interrupt Disable 9 1 write-only ITER Max number of Repetitions Reached Disable 10 1 write-only TXBUFE Buffer Empty Interrupt Disable 11 1 write-only RXBUFF Buffer Full Interrupt Disable 12 1 write-only NACK Non AcknowledgeInterrupt Disable 13 1 write-only RIIC Ring Indicator Input Change Disable 16 1 write-only DSRIC Data Set Ready Input Change Disable 17 1 write-only DCDIC Data Carrier Detect Input Change Interrupt Disable 18 1 write-only CTSIC Clear to Send Input Change Interrupt Disable 19 1 write-only MANE Manchester Error Interrupt Disable 24 1 write-only IMR Interrupt Mask Register 0x00000010 32 read-only 0x00000000 RXRDY RXRDY Interrupt Mask 0 1 read-only TXRDY TXRDY Interrupt Mask 1 1 read-only RXBRK Receiver Break Interrupt Mask 2 1 read-only ENDRX End of Receive Transfer Interrupt Mask 3 1 read-only ENDTX End of Transmit Interrupt Mask 4 1 read-only OVRE Overrun Error Interrupt Mask 5 1 read-only FRAME Framing Error Interrupt Mask 6 1 read-only PARE Parity Error Interrupt Mask 7 1 read-only TIMEOUT Time-out Interrupt Mask 8 1 read-only TXEMPTY TXEMPTY Interrupt Mask 9 1 read-only ITER Max number of Repetitions Reached Mask 10 1 read-only TXBUFE Buffer Empty Interrupt Mask 11 1 read-only RXBUFF Buffer Full Interrupt Mask 12 1 read-only NACK Non AcknowledgeInterrupt Mask 13 1 read-only RIIC Ring Indicator Input Change Mask 16 1 read-only DSRIC Data Set Ready Input Change Mask 17 1 read-only DCDIC Data Carrier Detect Input Change Interrupt Mask 18 1 read-only CTSIC Clear to Send Input Change Interrupt Mask 19 1 read-only MANE Manchester Error Interrupt Mask 24 1 read-only CSR Channel Status Register 0x00000014 32 read-only RXRDY Receiver Ready 0 1 read-only TXRDY Transmitter Ready 1 1 read-only RXBRK Break Received/End of Break 2 1 read-only ENDRX End of Receiver Transfer 3 1 read-only ENDTX End of Transmitter Transfer 4 1 read-only OVRE Overrun Error 5 1 read-only FRAME Framing Error 6 1 read-only PARE Parity Error 7 1 read-only TIMEOUT Receiver Time-out 8 1 read-only TXEMPTY Transmitter Empty 9 1 read-only ITER Max number of Repetitions Reached 10 1 read-only TXBUFE Transmission Buffer Empty 11 1 read-only RXBUFF Reception Buffer Full 12 1 read-only NACK Non AcknowledgeInterrupt 13 1 read-only RIIC Ring Indicator Input Change Flag 16 1 read-only DSRIC Data Set Ready Input Change Flag 17 1 read-only DCDIC Data Carrier Detect Input Change Flag 18 1 read-only CTSIC Clear to Send Input Change Flag 19 1 read-only RI Image of RI Input 20 1 read-only DSR Image of DSR Input 21 1 read-only DCD Image of DCD Input 22 1 read-only CTS Image of CTS Input 23 1 read-only MANERR Manchester Error 24 1 read-only RHR Receiver Holding Register 0x00000018 32 read-only 0x00000000 RXCHR Received Character 0 9 read-only RXSYNH Received Sync 15 1 read-only THR Transmitter Holding Register 0x0000001C 32 write-only TXCHR Character to be Transmitted 0 9 write-only TXSYNH Sync Field to be transmitted 15 1 write-only BRGR Baud Rate Generator Register 0x00000020 32 read-write 0x00000000 CD Clock Divider 0 16 read-write FP Fractional Part 16 3 read-write RTOR Receiver Time-out Register 0x00000024 32 read-write 0x00000000 TO Time-out Value 0 16 read-write TTGR Transmitter Timeguard Register 0x00000028 32 read-write 0x00000000 TG Timeguard Value 0 8 read-write FIDI FI DI Ratio Register 0x00000040 32 read-write 0x00000174 FI_DI_RATIO FI Over DI Ratio Value 0 11 read-write NER Number of Errors Register 0x00000044 32 read-only NB_ERRORS Number of Errors 0 8 read-only IF IrDA Filter Register 0x0000004C 32 read-write 0x00000000 IRDA_FILTER IrDA Filter 0 8 read-write MAN Manchester Encoder Decoder Register 0x00000050 32 read-write 0x30011004 TX_PL Transmitter Preamble Length 0 4 read-write TX_PP Transmitter Preamble Pattern 8 2 read-write ALL_ONE The preamble is composed of '1's 0x0 ALL_ZERO The preamble is composed of '0's 0x1 ZERO_ONE The preamble is composed of '01's 0x2 ONE_ZERO The preamble is composed of '10's 0x3 TX_MPOL Transmitter Manchester Polarity 12 1 read-write RX_PL Receiver Preamble Length 16 4 read-write RX_PP Receiver Preamble Pattern detected 24 2 read-write ALL_ONE The preamble is composed of '1's 0x0 ALL_ZERO The preamble is composed of '0's 0x1 ZERO_ONE The preamble is composed of '01's 0x2 ONE_ZERO The preamble is composed of '10's 0x3 RX_MPOL Receiver Manchester Polarity 28 1 read-write STUCKTO1 29 1 read-write DRIFT Drift compensation 30 1 read-write RPR Receive Pointer Register 0x00000100 32 read-write 0x00000000 RXPTR Receive Pointer Register 0 32 read-write RCR Receive Counter Register 0x00000104 32 read-write 0x00000000 RXCTR Receive Counter Register 0 16 read-write TPR Transmit Pointer Register 0x00000108 32 read-write 0x00000000 TXPTR Transmit Counter Register 0 32 read-write TCR Transmit Counter Register 0x0000010C 32 read-write 0x00000000 TXCTR Transmit Counter Register 0 16 read-write RNPR Receive Next Pointer Register 0x00000110 32 read-write 0x00000000 RXNPTR Receive Next Pointer 0 32 read-write RNCR Receive Next Counter Register 0x00000114 32 read-write 0x00000000 RXNCTR Receive Next Counter 0 16 read-write TNPR Transmit Next Pointer Register 0x00000118 32 read-write 0x00000000 TXNPTR Transmit Next Pointer 0 32 read-write TNCR Transmit Next Counter Register 0x0000011C 32 read-write 0x00000000 TXNCTR Transmit Counter Next 0 16 read-write PTCR Transfer Control Register 0x00000120 32 write-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 write-only RXTDIS Receiver Transfer Disable 1 1 write-only TXTEN Transmitter Transfer Enable 8 1 write-only TXTDIS Transmitter Transfer Disable 9 1 write-only PTSR Transfer Status Register 0x00000124 32 read-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 read-only TXTEN Transmitter Transfer Enable 8 1 read-only USART5 6089V Universal Synchronous Asynchronous Receiver Transmitter 5 USART USART5_ 0xFFFD8000 0 0x4000 registers USART5 25 CR Control Register 0x00000000 32 write-only RSTRX Reset Receiver 2 1 write-only RSTTX Reset Transmitter 3 1 write-only RXEN Receiver Enable 4 1 write-only RXDIS Receiver Disable 5 1 write-only TXEN Transmitter Enable 6 1 write-only TXDIS Transmitter Disable 7 1 write-only RSTSTA Reset Status Bits 8 1 write-only STTBRK Start Break 9 1 write-only STPBRK Stop Break 10 1 write-only STTTO Start Time-out 11 1 write-only SENDA Send Address 12 1 write-only RSTIT Reset Iterations 13 1 write-only RSTNACK Reset Non Acknowledge 14 1 write-only RETTO Rearm Time-out 15 1 write-only DTREN Data Terminal Ready Enable 16 1 write-only DTRDIS Data Terminal Ready Disable 17 1 write-only RTSEN Request to Send Enable 18 1 write-only RTSDIS Request to Send Disable 19 1 write-only MR Mode Register 0x00000004 32 read-write USART_MODE 0 4 read-write NORMAL Normal mode 0x0 RS485 RS485 0x1 HW_HANDSHAKING Hardware Handshaking 0x2 MODEM Modem 0x3 IS07816_T_0 IS07816 Protocol: T = 0 0x4 IS07816_T_1 IS07816 Protocol: T = 1 0x6 IRDA IrDA 0x8 USCLKS Clock Selection 4 2 read-write MCK Master Clock MCK is selected 0x0 DIV Internal Clock Divided MCK/DIV (DIV=8) is selected 0x1 SCK Serial Clock SLK is selected 0x3 CHRL Character Length. 6 2 read-write 5_BIT Character length is 5 bits 0x0 6_BIT Character length is 6 bits 0x1 7_BIT Character length is 7 bits 0x2 8_BIT Character length is 8 bits 0x3 SYNC Synchronous Mode Select 8 1 read-write PAR Parity Type 9 3 read-write EVEN Even parity 0x0 ODD Odd parity 0x1 SPACE Parity forced to 0 (Space) 0x2 MARK Parity forced to 1 (Mark) 0x3 NO No parity 0x4 MULTIDROP Multidrop mode 0x6 NBSTOP Number of Stop Bits 12 2 read-write 1_BIT 1 stop bit 0x0 1_5_BIT 1.5 stop bit (SYNC = 0) or reserved (SYNC = 1) 0x1 2_BIT 2 stop bits 0x2 CHMODE Channel Mode 14 2 read-write NORMAL Normal Mode 0x0 AUTOMATIC Automatic Echo. Receiver input is connected to the TXD pin. 0x1 LOCAL_LOOPBACK Local Loopback. Transmitter output is connected to the Receiver Input. 0x2 REMOTE_LOOPBACK Remote Loopback. RXD pin is internally connected to the TXD pin. 0x3 MSBF Bit Order 16 1 read-write MODE9 9-bit Character Length 17 1 read-write CLKO Clock Output Select 18 1 read-write OVER Oversampling Mode 19 1 read-write INACK Inhibit Non Acknowledge 20 1 read-write DSNACK Disable Successive NACK 21 1 read-write VAR_SYNC Variable Synchronization of Command/Data Sync Start Frame Delimiter 22 1 read-write MAX_ITERATION 24 3 read-write FILTER Infrared Receive Line Filter 28 1 read-write MAN Manchester Encoder/Decoder Enable 29 1 read-write MODSYNC Manchester Synchronization Mode 30 1 read-write ONEBIT Start Frame Delimiter Selector 31 1 read-write IER Interrupt Enable Register 0x00000008 32 write-only RXRDY RXRDY Interrupt Enable 0 1 write-only TXRDY TXRDY Interrupt Enable 1 1 write-only RXBRK Receiver Break Interrupt Enable 2 1 write-only ENDRX End of Receive Transfer Interrupt Enable 3 1 write-only ENDTX End of Transmit Interrupt Enable 4 1 write-only OVRE Overrun Error Interrupt Enable 5 1 write-only FRAME Framing Error Interrupt Enable 6 1 write-only PARE Parity Error Interrupt Enable 7 1 write-only TIMEOUT Time-out Interrupt Enable 8 1 write-only TXEMPTY TXEMPTY Interrupt Enable 9 1 write-only ITER Max number of Repetitions Reached 10 1 write-only TXBUFE Buffer Empty Interrupt Enable 11 1 write-only RXBUFF Buffer Full Interrupt Enable 12 1 write-only NACK Non AcknowledgeInterrupt Enable 13 1 write-only RIIC Ring Indicator Input Change Enable 16 1 write-only DSRIC Data Set Ready Input Change Enable 17 1 write-only DCDIC Data Carrier Detect Input Change Interrupt Enable 18 1 write-only CTSIC Clear to Send Input Change Interrupt Enable 19 1 write-only MANE Manchester Error Interrupt Enable 24 1 write-only IDR Interrupt Disable Register 0x0000000C 32 write-only RXRDY RXRDY Interrupt Disable 0 1 write-only TXRDY TXRDY Interrupt Disable 1 1 write-only RXBRK Receiver Break Interrupt Disable 2 1 write-only ENDRX End of Receive Transfer Interrupt Disable 3 1 write-only ENDTX End of Transmit Interrupt Disable 4 1 write-only OVRE Overrun Error Interrupt Disable 5 1 write-only FRAME Framing Error Interrupt Disable 6 1 write-only PARE Parity Error Interrupt Disable 7 1 write-only TIMEOUT Time-out Interrupt Disable 8 1 write-only TXEMPTY TXEMPTY Interrupt Disable 9 1 write-only ITER Max number of Repetitions Reached Disable 10 1 write-only TXBUFE Buffer Empty Interrupt Disable 11 1 write-only RXBUFF Buffer Full Interrupt Disable 12 1 write-only NACK Non AcknowledgeInterrupt Disable 13 1 write-only RIIC Ring Indicator Input Change Disable 16 1 write-only DSRIC Data Set Ready Input Change Disable 17 1 write-only DCDIC Data Carrier Detect Input Change Interrupt Disable 18 1 write-only CTSIC Clear to Send Input Change Interrupt Disable 19 1 write-only MANE Manchester Error Interrupt Disable 24 1 write-only IMR Interrupt Mask Register 0x00000010 32 read-only 0x00000000 RXRDY RXRDY Interrupt Mask 0 1 read-only TXRDY TXRDY Interrupt Mask 1 1 read-only RXBRK Receiver Break Interrupt Mask 2 1 read-only ENDRX End of Receive Transfer Interrupt Mask 3 1 read-only ENDTX End of Transmit Interrupt Mask 4 1 read-only OVRE Overrun Error Interrupt Mask 5 1 read-only FRAME Framing Error Interrupt Mask 6 1 read-only PARE Parity Error Interrupt Mask 7 1 read-only TIMEOUT Time-out Interrupt Mask 8 1 read-only TXEMPTY TXEMPTY Interrupt Mask 9 1 read-only ITER Max number of Repetitions Reached Mask 10 1 read-only TXBUFE Buffer Empty Interrupt Mask 11 1 read-only RXBUFF Buffer Full Interrupt Mask 12 1 read-only NACK Non AcknowledgeInterrupt Mask 13 1 read-only RIIC Ring Indicator Input Change Mask 16 1 read-only DSRIC Data Set Ready Input Change Mask 17 1 read-only DCDIC Data Carrier Detect Input Change Interrupt Mask 18 1 read-only CTSIC Clear to Send Input Change Interrupt Mask 19 1 read-only MANE Manchester Error Interrupt Mask 24 1 read-only CSR Channel Status Register 0x00000014 32 read-only RXRDY Receiver Ready 0 1 read-only TXRDY Transmitter Ready 1 1 read-only RXBRK Break Received/End of Break 2 1 read-only ENDRX End of Receiver Transfer 3 1 read-only ENDTX End of Transmitter Transfer 4 1 read-only OVRE Overrun Error 5 1 read-only FRAME Framing Error 6 1 read-only PARE Parity Error 7 1 read-only TIMEOUT Receiver Time-out 8 1 read-only TXEMPTY Transmitter Empty 9 1 read-only ITER Max number of Repetitions Reached 10 1 read-only TXBUFE Transmission Buffer Empty 11 1 read-only RXBUFF Reception Buffer Full 12 1 read-only NACK Non AcknowledgeInterrupt 13 1 read-only RIIC Ring Indicator Input Change Flag 16 1 read-only DSRIC Data Set Ready Input Change Flag 17 1 read-only DCDIC Data Carrier Detect Input Change Flag 18 1 read-only CTSIC Clear to Send Input Change Flag 19 1 read-only RI Image of RI Input 20 1 read-only DSR Image of DSR Input 21 1 read-only DCD Image of DCD Input 22 1 read-only CTS Image of CTS Input 23 1 read-only MANERR Manchester Error 24 1 read-only RHR Receiver Holding Register 0x00000018 32 read-only 0x00000000 RXCHR Received Character 0 9 read-only RXSYNH Received Sync 15 1 read-only THR Transmitter Holding Register 0x0000001C 32 write-only TXCHR Character to be Transmitted 0 9 write-only TXSYNH Sync Field to be transmitted 15 1 write-only BRGR Baud Rate Generator Register 0x00000020 32 read-write 0x00000000 CD Clock Divider 0 16 read-write FP Fractional Part 16 3 read-write RTOR Receiver Time-out Register 0x00000024 32 read-write 0x00000000 TO Time-out Value 0 16 read-write TTGR Transmitter Timeguard Register 0x00000028 32 read-write 0x00000000 TG Timeguard Value 0 8 read-write FIDI FI DI Ratio Register 0x00000040 32 read-write 0x00000174 FI_DI_RATIO FI Over DI Ratio Value 0 11 read-write NER Number of Errors Register 0x00000044 32 read-only NB_ERRORS Number of Errors 0 8 read-only IF IrDA Filter Register 0x0000004C 32 read-write 0x00000000 IRDA_FILTER IrDA Filter 0 8 read-write MAN Manchester Encoder Decoder Register 0x00000050 32 read-write 0x30011004 TX_PL Transmitter Preamble Length 0 4 read-write TX_PP Transmitter Preamble Pattern 8 2 read-write ALL_ONE The preamble is composed of '1's 0x0 ALL_ZERO The preamble is composed of '0's 0x1 ZERO_ONE The preamble is composed of '01's 0x2 ONE_ZERO The preamble is composed of '10's 0x3 TX_MPOL Transmitter Manchester Polarity 12 1 read-write RX_PL Receiver Preamble Length 16 4 read-write RX_PP Receiver Preamble Pattern detected 24 2 read-write ALL_ONE The preamble is composed of '1's 0x0 ALL_ZERO The preamble is composed of '0's 0x1 ZERO_ONE The preamble is composed of '01's 0x2 ONE_ZERO The preamble is composed of '10's 0x3 RX_MPOL Receiver Manchester Polarity 28 1 read-write STUCKTO1 29 1 read-write DRIFT Drift compensation 30 1 read-write RPR Receive Pointer Register 0x00000100 32 read-write 0x00000000 RXPTR Receive Pointer Register 0 32 read-write RCR Receive Counter Register 0x00000104 32 read-write 0x00000000 RXCTR Receive Counter Register 0 16 read-write TPR Transmit Pointer Register 0x00000108 32 read-write 0x00000000 TXPTR Transmit Counter Register 0 32 read-write TCR Transmit Counter Register 0x0000010C 32 read-write 0x00000000 TXCTR Transmit Counter Register 0 16 read-write RNPR Receive Next Pointer Register 0x00000110 32 read-write 0x00000000 RXNPTR Receive Next Pointer 0 32 read-write RNCR Receive Next Counter Register 0x00000114 32 read-write 0x00000000 RXNCTR Receive Next Counter 0 16 read-write TNPR Transmit Next Pointer Register 0x00000118 32 read-write 0x00000000 TXNPTR Transmit Next Pointer 0 32 read-write TNCR Transmit Next Counter Register 0x0000011C 32 read-write 0x00000000 TXNCTR Transmit Counter Next 0 16 read-write PTCR Transfer Control Register 0x00000120 32 write-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 write-only RXTDIS Receiver Transfer Disable 1 1 write-only TXTEN Transmitter Transfer Enable 8 1 write-only TXTDIS Transmitter Transfer Disable 9 1 write-only PTSR Transfer Status Register 0x00000124 32 read-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 read-only TXTEN Transmitter Transfer Enable 8 1 read-only TC1 6082L Timer Counter 1 TC TC1_ 0xFFFDC000 0 0x4000 registers TC3 26 TC4 27 TC5 28 CCR0 Channel Control Register (channel = 0) 0x00000000 32 write-only CLKEN Counter Clock Enable Command 0 1 write-only CLKDIS Counter Clock Disable Command 1 1 write-only SWTRG Software Trigger Command 2 1 write-only CMR0 Channel Mode Register (channel = 0) 0x00000004 32 read-write 0x00000000 TCCLKS Clock Selection 0 3 read-write TIMER_CLOCK1 Clock selected: TCLK1 0x0 TIMER_CLOCK2 Clock selected: TCLK2 0x1 TIMER_CLOCK3 Clock selected: TCLK3 0x2 TIMER_CLOCK4 Clock selected: TCLK4 0x3 TIMER_CLOCK5 Clock selected: TCLK5 0x4 XC0 Clock selected: XC0 0x5 XC1 Clock selected: XC1 0x6 XC2 Clock selected: XC2 0x7 CLKI Clock Invert 3 1 read-write BURST Burst Signal Selection 4 2 read-write NONE The clock is not gated by an external signal. 0x0 XC0 XC0 is ANDed with the selected clock. 0x1 XC1 XC1 is ANDed with the selected clock. 0x2 XC2 XC2 is ANDed with the selected clock. 0x3 LDBSTOP Counter Clock Stopped with RB Loading 6 1 read-write LDBDIS Counter Clock Disable with RB Loading 7 1 read-write ETRGEDG External Trigger Edge Selection 8 2 read-write NONE The clock is not gated by an external signal. 0x0 RISING Rising edge 0x1 FALLING Falling edge 0x2 EDGE Each edge 0x3 ABETRG TIOA or TIOB External Trigger Selection 10 1 read-write CPCTRG RC Compare Trigger Enable 14 1 read-write WAVE 15 1 read-write LDRA RA Loading Selection 16 2 read-write NONE None 0x0 RISING Rising edge of TIOA 0x1 FALLING Falling edge of TIOA 0x2 EDGE Each edge of TIOA 0x3 LDRB RB Loading Selection 18 2 read-write NONE None 0x0 RISING Rising edge of TIOA 0x1 FALLING Falling edge of TIOA 0x2 EDGE Each edge of TIOA 0x3 CMR0_WAVE_EQ_1 Channel Mode Register (channel = 0) WAVE_EQ_1 0x00000004 32 read-write 0x00000000 TCCLKS Clock Selection 0 3 read-write TIMER_CLOCK1 Clock selected: TCLK1 0x0 TIMER_CLOCK2 Clock selected: TCLK2 0x1 TIMER_CLOCK3 Clock selected: TCLK3 0x2 TIMER_CLOCK4 Clock selected: TCLK4 0x3 TIMER_CLOCK5 Clock selected: TCLK5 0x4 XC0 Clock selected: XC0 0x5 XC1 Clock selected: XC1 0x6 XC2 Clock selected: XC2 0x7 CLKI Clock Invert 3 1 read-write BURST Burst Signal Selection 4 2 read-write NONE The clock is not gated by an external signal. 0x0 XC0 XC0 is ANDed with the selected clock. 0x1 XC1 XC1 is ANDed with the selected clock. 0x2 XC2 XC2 is ANDed with the selected clock. 0x3 CPCSTOP Counter Clock Stopped with RC Compare 6 1 read-write CPCDIS Counter Clock Disable with RC Compare 7 1 read-write EEVTEDG External Event Edge Selection 8 2 read-write NONE None 0x0 RISING Rising edge 0x1 FALLING Falling edge 0x2 EDGE Each edge 0x3 EEVT External Event Selection 10 2 read-write TIOB TIOB 0x0 XC0 XC0 0x1 XC1 XC1 0x2 XC2 XC2 0x3 ENETRG External Event Trigger Enable 12 1 read-write WAVSEL Waveform Selection 13 2 read-write UP UP mode without automatic trigger on RC Compare 0x0 UPDOWN UPDOWN mode without automatic trigger on RC Compare 0x1 UP_RC UP mode with automatic trigger on RC Compare 0x2 UPDOWN_RC UPDOWN mode with automatic trigger on RC Compare 0x3 WAVE 15 1 read-write ACPA RA Compare Effect on TIOA 16 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 ACPC RC Compare Effect on TIOA 18 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 AEEVT External Event Effect on TIOA 20 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 ASWTRG Software Trigger Effect on TIOA 22 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BCPB RB Compare Effect on TIOB 24 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BCPC RC Compare Effect on TIOB 26 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BEEVT External Event Effect on TIOB 28 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BSWTRG Software Trigger Effect on TIOB 30 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 CV0 Counter Value (channel = 0) 0x00000010 32 read-only 0x00000000 CV Counter Value 0 16 read-only RA0 Register A (channel = 0) 0x00000014 32 read-write 0x00000000 RA Register A 0 16 read-write RB0 Register B (channel = 0) 0x00000018 32 read-write 0x00000000 RB Register B 0 16 read-write RC0 Register C (channel = 0) 0x0000001C 32 read-write 0x00000000 RC Register C 0 16 read-write SR0 Status Register (channel = 0) 0x00000020 32 read-only 0x00000000 COVFS Counter Overflow Status 0 1 read-only LOVRS Load Overrun Status 1 1 read-only CPAS RA Compare Status 2 1 read-only CPBS RB Compare Status 3 1 read-only CPCS RC Compare Status 4 1 read-only LDRAS RA Loading Status 5 1 read-only LDRBS RB Loading Status 6 1 read-only ETRGS External Trigger Status 7 1 read-only CLKSTA Clock Enabling Status 16 1 read-only MTIOA TIOA Mirror 17 1 read-only MTIOB TIOB Mirror 18 1 read-only IER0 Interrupt Enable Register (channel = 0) 0x00000024 32 write-only COVFS Counter Overflow 0 1 write-only LOVRS Load Overrun 1 1 write-only CPAS RA Compare 2 1 write-only CPBS RB Compare 3 1 write-only CPCS RC Compare 4 1 write-only LDRAS RA Loading 5 1 write-only LDRBS RB Loading 6 1 write-only ETRGS External Trigger 7 1 write-only IDR0 Interrupt Disable Register (channel = 0) 0x00000028 32 write-only COVFS Counter Overflow 0 1 write-only LOVRS Load Overrun 1 1 write-only CPAS RA Compare 2 1 write-only CPBS RB Compare 3 1 write-only CPCS RC Compare 4 1 write-only LDRAS RA Loading 5 1 write-only LDRBS RB Loading 6 1 write-only ETRGS External Trigger 7 1 write-only IMR0 Interrupt Mask Register (channel = 0) 0x0000002C 32 read-only 0x00000000 COVFS Counter Overflow 0 1 read-only LOVRS Load Overrun 1 1 read-only CPAS RA Compare 2 1 read-only CPBS RB Compare 3 1 read-only CPCS RC Compare 4 1 read-only LDRAS RA Loading 5 1 read-only LDRBS RB Loading 6 1 read-only ETRGS External Trigger 7 1 read-only CCR1 Channel Control Register (channel = 1) 0x00000040 32 write-only CLKEN Counter Clock Enable Command 0 1 write-only CLKDIS Counter Clock Disable Command 1 1 write-only SWTRG Software Trigger Command 2 1 write-only CMR1 Channel Mode Register (channel = 1) 0x00000044 32 read-write 0x00000000 TCCLKS Clock Selection 0 3 read-write TIMER_CLOCK1 Clock selected: TCLK1 0x0 TIMER_CLOCK2 Clock selected: TCLK2 0x1 TIMER_CLOCK3 Clock selected: TCLK3 0x2 TIMER_CLOCK4 Clock selected: TCLK4 0x3 TIMER_CLOCK5 Clock selected: TCLK5 0x4 XC0 Clock selected: XC0 0x5 XC1 Clock selected: XC1 0x6 XC2 Clock selected: XC2 0x7 CLKI Clock Invert 3 1 read-write BURST Burst Signal Selection 4 2 read-write NONE The clock is not gated by an external signal. 0x0 XC0 XC0 is ANDed with the selected clock. 0x1 XC1 XC1 is ANDed with the selected clock. 0x2 XC2 XC2 is ANDed with the selected clock. 0x3 LDBSTOP Counter Clock Stopped with RB Loading 6 1 read-write LDBDIS Counter Clock Disable with RB Loading 7 1 read-write ETRGEDG External Trigger Edge Selection 8 2 read-write NONE The clock is not gated by an external signal. 0x0 RISING Rising edge 0x1 FALLING Falling edge 0x2 EDGE Each edge 0x3 ABETRG TIOA or TIOB External Trigger Selection 10 1 read-write CPCTRG RC Compare Trigger Enable 14 1 read-write WAVE 15 1 read-write LDRA RA Loading Selection 16 2 read-write NONE None 0x0 RISING Rising edge of TIOA 0x1 FALLING Falling edge of TIOA 0x2 EDGE Each edge of TIOA 0x3 LDRB RB Loading Selection 18 2 read-write NONE None 0x0 RISING Rising edge of TIOA 0x1 FALLING Falling edge of TIOA 0x2 EDGE Each edge of TIOA 0x3 CMR1_WAVE_EQ_1 Channel Mode Register (channel = 1) WAVE_EQ_1 0x00000044 32 read-write 0x00000000 TCCLKS Clock Selection 0 3 read-write TIMER_CLOCK1 Clock selected: TCLK1 0x0 TIMER_CLOCK2 Clock selected: TCLK2 0x1 TIMER_CLOCK3 Clock selected: TCLK3 0x2 TIMER_CLOCK4 Clock selected: TCLK4 0x3 TIMER_CLOCK5 Clock selected: TCLK5 0x4 XC0 Clock selected: XC0 0x5 XC1 Clock selected: XC1 0x6 XC2 Clock selected: XC2 0x7 CLKI Clock Invert 3 1 read-write BURST Burst Signal Selection 4 2 read-write NONE The clock is not gated by an external signal. 0x0 XC0 XC0 is ANDed with the selected clock. 0x1 XC1 XC1 is ANDed with the selected clock. 0x2 XC2 XC2 is ANDed with the selected clock. 0x3 CPCSTOP Counter Clock Stopped with RC Compare 6 1 read-write CPCDIS Counter Clock Disable with RC Compare 7 1 read-write EEVTEDG External Event Edge Selection 8 2 read-write NONE None 0x0 RISING Rising edge 0x1 FALLING Falling edge 0x2 EDGE Each edge 0x3 EEVT External Event Selection 10 2 read-write TIOB TIOB 0x0 XC0 XC0 0x1 XC1 XC1 0x2 XC2 XC2 0x3 ENETRG External Event Trigger Enable 12 1 read-write WAVSEL Waveform Selection 13 2 read-write UP UP mode without automatic trigger on RC Compare 0x0 UPDOWN UPDOWN mode without automatic trigger on RC Compare 0x1 UP_RC UP mode with automatic trigger on RC Compare 0x2 UPDOWN_RC UPDOWN mode with automatic trigger on RC Compare 0x3 WAVE 15 1 read-write ACPA RA Compare Effect on TIOA 16 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 ACPC RC Compare Effect on TIOA 18 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 AEEVT External Event Effect on TIOA 20 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 ASWTRG Software Trigger Effect on TIOA 22 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BCPB RB Compare Effect on TIOB 24 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BCPC RC Compare Effect on TIOB 26 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BEEVT External Event Effect on TIOB 28 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BSWTRG Software Trigger Effect on TIOB 30 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 CV1 Counter Value (channel = 1) 0x00000050 32 read-only 0x00000000 CV Counter Value 0 16 read-only RA1 Register A (channel = 1) 0x00000054 32 read-write 0x00000000 RA Register A 0 16 read-write RB1 Register B (channel = 1) 0x00000058 32 read-write 0x00000000 RB Register B 0 16 read-write RC1 Register C (channel = 1) 0x0000005C 32 read-write 0x00000000 RC Register C 0 16 read-write SR1 Status Register (channel = 1) 0x00000060 32 read-only 0x00000000 COVFS Counter Overflow Status 0 1 read-only LOVRS Load Overrun Status 1 1 read-only CPAS RA Compare Status 2 1 read-only CPBS RB Compare Status 3 1 read-only CPCS RC Compare Status 4 1 read-only LDRAS RA Loading Status 5 1 read-only LDRBS RB Loading Status 6 1 read-only ETRGS External Trigger Status 7 1 read-only CLKSTA Clock Enabling Status 16 1 read-only MTIOA TIOA Mirror 17 1 read-only MTIOB TIOB Mirror 18 1 read-only IER1 Interrupt Enable Register (channel = 1) 0x00000064 32 write-only COVFS Counter Overflow 0 1 write-only LOVRS Load Overrun 1 1 write-only CPAS RA Compare 2 1 write-only CPBS RB Compare 3 1 write-only CPCS RC Compare 4 1 write-only LDRAS RA Loading 5 1 write-only LDRBS RB Loading 6 1 write-only ETRGS External Trigger 7 1 write-only IDR1 Interrupt Disable Register (channel = 1) 0x00000068 32 write-only COVFS Counter Overflow 0 1 write-only LOVRS Load Overrun 1 1 write-only CPAS RA Compare 2 1 write-only CPBS RB Compare 3 1 write-only CPCS RC Compare 4 1 write-only LDRAS RA Loading 5 1 write-only LDRBS RB Loading 6 1 write-only ETRGS External Trigger 7 1 write-only IMR1 Interrupt Mask Register (channel = 1) 0x0000006C 32 read-only 0x00000000 COVFS Counter Overflow 0 1 read-only LOVRS Load Overrun 1 1 read-only CPAS RA Compare 2 1 read-only CPBS RB Compare 3 1 read-only CPCS RC Compare 4 1 read-only LDRAS RA Loading 5 1 read-only LDRBS RB Loading 6 1 read-only ETRGS External Trigger 7 1 read-only CCR2 Channel Control Register (channel = 2) 0x00000080 32 write-only CLKEN Counter Clock Enable Command 0 1 write-only CLKDIS Counter Clock Disable Command 1 1 write-only SWTRG Software Trigger Command 2 1 write-only CMR2 Channel Mode Register (channel = 2) 0x00000084 32 read-write 0x00000000 TCCLKS Clock Selection 0 3 read-write TIMER_CLOCK1 Clock selected: TCLK1 0x0 TIMER_CLOCK2 Clock selected: TCLK2 0x1 TIMER_CLOCK3 Clock selected: TCLK3 0x2 TIMER_CLOCK4 Clock selected: TCLK4 0x3 TIMER_CLOCK5 Clock selected: TCLK5 0x4 XC0 Clock selected: XC0 0x5 XC1 Clock selected: XC1 0x6 XC2 Clock selected: XC2 0x7 CLKI Clock Invert 3 1 read-write BURST Burst Signal Selection 4 2 read-write NONE The clock is not gated by an external signal. 0x0 XC0 XC0 is ANDed with the selected clock. 0x1 XC1 XC1 is ANDed with the selected clock. 0x2 XC2 XC2 is ANDed with the selected clock. 0x3 LDBSTOP Counter Clock Stopped with RB Loading 6 1 read-write LDBDIS Counter Clock Disable with RB Loading 7 1 read-write ETRGEDG External Trigger Edge Selection 8 2 read-write NONE The clock is not gated by an external signal. 0x0 RISING Rising edge 0x1 FALLING Falling edge 0x2 EDGE Each edge 0x3 ABETRG TIOA or TIOB External Trigger Selection 10 1 read-write CPCTRG RC Compare Trigger Enable 14 1 read-write WAVE 15 1 read-write LDRA RA Loading Selection 16 2 read-write NONE None 0x0 RISING Rising edge of TIOA 0x1 FALLING Falling edge of TIOA 0x2 EDGE Each edge of TIOA 0x3 LDRB RB Loading Selection 18 2 read-write NONE None 0x0 RISING Rising edge of TIOA 0x1 FALLING Falling edge of TIOA 0x2 EDGE Each edge of TIOA 0x3 CMR2_WAVE_EQ_1 Channel Mode Register (channel = 2) WAVE_EQ_1 0x00000084 32 read-write 0x00000000 TCCLKS Clock Selection 0 3 read-write TIMER_CLOCK1 Clock selected: TCLK1 0x0 TIMER_CLOCK2 Clock selected: TCLK2 0x1 TIMER_CLOCK3 Clock selected: TCLK3 0x2 TIMER_CLOCK4 Clock selected: TCLK4 0x3 TIMER_CLOCK5 Clock selected: TCLK5 0x4 XC0 Clock selected: XC0 0x5 XC1 Clock selected: XC1 0x6 XC2 Clock selected: XC2 0x7 CLKI Clock Invert 3 1 read-write BURST Burst Signal Selection 4 2 read-write NONE The clock is not gated by an external signal. 0x0 XC0 XC0 is ANDed with the selected clock. 0x1 XC1 XC1 is ANDed with the selected clock. 0x2 XC2 XC2 is ANDed with the selected clock. 0x3 CPCSTOP Counter Clock Stopped with RC Compare 6 1 read-write CPCDIS Counter Clock Disable with RC Compare 7 1 read-write EEVTEDG External Event Edge Selection 8 2 read-write NONE None 0x0 RISING Rising edge 0x1 FALLING Falling edge 0x2 EDGE Each edge 0x3 EEVT External Event Selection 10 2 read-write TIOB TIOB 0x0 XC0 XC0 0x1 XC1 XC1 0x2 XC2 XC2 0x3 ENETRG External Event Trigger Enable 12 1 read-write WAVSEL Waveform Selection 13 2 read-write UP UP mode without automatic trigger on RC Compare 0x0 UPDOWN UPDOWN mode without automatic trigger on RC Compare 0x1 UP_RC UP mode with automatic trigger on RC Compare 0x2 UPDOWN_RC UPDOWN mode with automatic trigger on RC Compare 0x3 WAVE 15 1 read-write ACPA RA Compare Effect on TIOA 16 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 ACPC RC Compare Effect on TIOA 18 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 AEEVT External Event Effect on TIOA 20 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 ASWTRG Software Trigger Effect on TIOA 22 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BCPB RB Compare Effect on TIOB 24 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BCPC RC Compare Effect on TIOB 26 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BEEVT External Event Effect on TIOB 28 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 BSWTRG Software Trigger Effect on TIOB 30 2 read-write NONE None 0x0 SET Set 0x1 CLEAR Clear 0x2 TOGGLE Toggle 0x3 CV2 Counter Value (channel = 2) 0x00000090 32 read-only 0x00000000 CV Counter Value 0 16 read-only RA2 Register A (channel = 2) 0x00000094 32 read-write 0x00000000 RA Register A 0 16 read-write RB2 Register B (channel = 2) 0x00000098 32 read-write 0x00000000 RB Register B 0 16 read-write RC2 Register C (channel = 2) 0x0000009C 32 read-write 0x00000000 RC Register C 0 16 read-write SR2 Status Register (channel = 2) 0x000000A0 32 read-only 0x00000000 COVFS Counter Overflow Status 0 1 read-only LOVRS Load Overrun Status 1 1 read-only CPAS RA Compare Status 2 1 read-only CPBS RB Compare Status 3 1 read-only CPCS RC Compare Status 4 1 read-only LDRAS RA Loading Status 5 1 read-only LDRBS RB Loading Status 6 1 read-only ETRGS External Trigger Status 7 1 read-only CLKSTA Clock Enabling Status 16 1 read-only MTIOA TIOA Mirror 17 1 read-only MTIOB TIOB Mirror 18 1 read-only IER2 Interrupt Enable Register (channel = 2) 0x000000A4 32 write-only COVFS Counter Overflow 0 1 write-only LOVRS Load Overrun 1 1 write-only CPAS RA Compare 2 1 write-only CPBS RB Compare 3 1 write-only CPCS RC Compare 4 1 write-only LDRAS RA Loading 5 1 write-only LDRBS RB Loading 6 1 write-only ETRGS External Trigger 7 1 write-only IDR2 Interrupt Disable Register (channel = 2) 0x000000A8 32 write-only COVFS Counter Overflow 0 1 write-only LOVRS Load Overrun 1 1 write-only CPAS RA Compare 2 1 write-only CPBS RB Compare 3 1 write-only CPCS RC Compare 4 1 write-only LDRAS RA Loading 5 1 write-only LDRBS RB Loading 6 1 write-only ETRGS External Trigger 7 1 write-only IMR2 Interrupt Mask Register (channel = 2) 0x000000AC 32 read-only 0x00000000 COVFS Counter Overflow 0 1 read-only LOVRS Load Overrun 1 1 read-only CPAS RA Compare 2 1 read-only CPBS RB Compare 3 1 read-only CPCS RC Compare 4 1 read-only LDRAS RA Loading 5 1 read-only LDRBS RB Loading 6 1 read-only ETRGS External Trigger 7 1 read-only BCR Block Control Register 0x000000C0 32 write-only SYNC Synchro Command 0 1 write-only BMR Block Mode Register 0x000000C4 32 read-write 0x00000000 TC0XC0S External Clock Signal 0 Selection 0 2 read-write TCLK0 Signal connected to XC0: TCLK0 0x0 TIOA1 Signal connected to XC0: TIOA1 0x2 TIOA2 Signal connected to XC0: TIOA2 0x3 TC1XC1S External Clock Signal 1 Selection 2 2 read-write TCLK1 Signal connected to XC1: TCLK1 0x0 TIOA0 Signal connected to XC1: TIOA0 0x2 TIOA2 Signal connected to XC1: TIOA2 0x3 TC2XC2S External Clock Signal 2 Selection 4 2 read-write TCLK2 Signal connected to XC2: TCLK2 0x0 TIOA1 Signal connected to XC2: TIOA1 0x2 TIOA2 Signal connected to XC2: TIOA2 0x3 ADC 6489J Analog-to-Digital Converter ADC_ 0xFFFE0000 0 0x4000 registers ADC 5 CR Control Register 0x00000000 32 write-only SWRST Software Reset 0 1 write-only START Start Conversion 1 1 write-only MR Mode Register 0x00000004 32 read-write 0x00000000 TRGEN Trigger Enable 0 1 read-write DIS Hardware triggers are disabled. Starting a conversion is only possible by software. 0 EN Hardware trigger selected by TRGSEL field is enabled. 1 TRGSEL Trigger Selection 1 3 read-write ADC_TRIG0 ADC_TRIG0 0x0 ADC_TRIG1 ADC_TRIG1 0x1 ADC_TRIG2 ADC_TRIG2 0x2 ADC_TRIG3 ADC_TRIG3 0x3 ADC_TRIG4 ADC_TRIG4 0x4 ADC_TRIG5 ADC_TRIG5 0x5 ADC_TRIG6 ADC_TRIG6 0x6 LOWRES Resolution 4 1 read-write BITS_10 10-bit resolution 0 BITS_8 8-bit resolution 1 SLEEP Sleep Mode 5 1 read-write NORMAL Normal Mode: The ADC Core and reference voltage circuitry are kept ON between conversions 0 SLEEP Sleep Mode: The ADC Core and reference voltage circuitry are OFF between conversions 1 FWUP Fast Wake Up 6 1 read-write OFF Normal Sleep Mode: The sleep mode is defined by the SLEEP bit 0 ON Fast Wake Up Sleep Mode: The Voltage reference is ON between conversions and ADC Core is OFF 1 FREERUN Free Run Mode 7 1 read-write OFF Normal Mode 0 ON Free Run Mode: Never wait for any trigger. 1 PRESCAL Prescaler Rate Selection 8 8 read-write STARTUP Start Up Time 16 4 read-write SUT0 0 periods of ADCClock 0x0 SUT8 8 periods of ADCClock 0x1 SUT16 16 periods of ADCClock 0x2 SUT24 24 periods of ADCClock 0x3 SUT64 64 periods of ADCClock 0x4 SUT80 80 periods of ADCClock 0x5 SUT96 96 periods of ADCClock 0x6 SUT112 112 periods of ADCClock 0x7 SUT512 512 periods of ADCClock 0x8 SUT576 576 periods of ADCClock 0x9 SUT640 640 periods of ADCClock 0xA SUT704 704 periods of ADCClock 0xB SUT768 768 periods of ADCClock 0xC SUT832 832 periods of ADCClock 0xD SUT896 896 periods of ADCClock 0xE SUT960 960 periods of ADCClock 0xF TRACKTIM Tracking Time 24 4 read-write USEQ Use Sequence Enable 31 1 read-write NUM_ORDER Normal Mode: The controller converts channels in a simple numeric order depending only on the channel index. 0 REG_ORDER User Sequence Mode: The sequence respects what is defined in ADC_SEQR1 and ADC_SEQR2 registers and can be used to convert several times the same channel. 1 SEQR1 Channel Sequence Register 1 0x00000008 32 read-write 0x00000000 USCH1 User Sequence Number 1 0 4 read-write USCH2 User Sequence Number 2 4 4 read-write USCH3 User Sequence Number 3 8 4 read-write USCH4 User Sequence Number 4 12 4 read-write USCH5 User Sequence Number 5 16 4 read-write USCH6 User Sequence Number 6 20 4 read-write USCH7 User Sequence Number 7 24 4 read-write USCH8 User Sequence Number 8 28 4 read-write SEQR2 Channel Sequence Register 2 0x0000000C 32 read-write 0x00000000 USCH9 User Sequence Number 9 0 4 read-write USCH10 User Sequence Number 10 4 4 read-write USCH11 User Sequence Number 11 8 4 read-write USCH12 User Sequence Number 12 12 4 read-write USCH13 User Sequence Number 13 16 4 read-write USCH14 User Sequence Number 14 20 4 read-write USCH15 User Sequence Number 15 24 4 read-write USCH16 User Sequence Number 16 28 4 read-write CHER Channel Enable Register 0x00000010 32 write-only CH0 Channel 0 Enable 0 1 write-only CH1 Channel 1 Enable 1 1 write-only CH2 Channel 2 Enable 2 1 write-only CH3 Channel 3 Enable 3 1 write-only CHDR Channel Disable Register 0x00000014 32 write-only CH0 Channel 0 Disable 0 1 write-only CH1 Channel 1 Disable 1 1 write-only CH2 Channel 2 Disable 2 1 write-only CH3 Channel 3 Disable 3 1 write-only CHSR Channel Status Register 0x00000018 32 read-only 0x00000000 CH0 Channel 0 Status 0 1 read-only CH1 Channel 1 Status 1 1 read-only CH2 Channel 2 Status 2 1 read-only CH3 Channel 3 Status 3 1 read-only LCDR Last Converted Data Register 0x00000020 32 read-only 0x00000000 LDATA Last Data Converted 0 12 read-only CHNB Channel Number 12 4 read-only IER Interrupt Enable Register 0x00000024 32 write-only EOC0 End of Conversion Interrupt Enable 0 0 1 write-only EOC1 End of Conversion Interrupt Enable 1 1 1 write-only EOC2 End of Conversion Interrupt Enable 2 2 1 write-only EOC3 End of Conversion Interrupt Enable 3 3 1 write-only DRDY Data Ready Interrupt Enable 24 1 write-only GOVRE General Overrun Error Interrupt Enable 25 1 write-only COMPE Comparison Event Interrupt Enable 26 1 write-only ENDRX End of Receive Buffer Interrupt Enable 27 1 write-only RXBUFF Receive Buffer Full Interrupt Enable 28 1 write-only IDR Interrupt Disable Register 0x00000028 32 write-only EOC0 End of Conversion Interrupt Disable 0 0 1 write-only EOC1 End of Conversion Interrupt Disable 1 1 1 write-only EOC2 End of Conversion Interrupt Disable 2 2 1 write-only EOC3 End of Conversion Interrupt Disable 3 3 1 write-only DRDY Data Ready Interrupt Disable 24 1 write-only GOVRE General Overrun Error Interrupt Disable 25 1 write-only COMPE Comparison Event Interrupt Disable 26 1 write-only ENDRX End of Receive Buffer Interrupt Disable 27 1 write-only RXBUFF Receive Buffer Full Interrupt Disable 28 1 write-only IMR Interrupt Mask Register 0x0000002C 32 read-only 0x00000000 EOC0 End of Conversion Interrupt Mask 0 0 1 read-only EOC1 End of Conversion Interrupt Mask 1 1 1 read-only EOC2 End of Conversion Interrupt Mask 2 2 1 read-only EOC3 End of Conversion Interrupt Mask 3 3 1 read-only DRDY Data Ready Interrupt Mask 24 1 read-only GOVRE General Overrun Error Interrupt Mask 25 1 read-only COMPE Comparison Event Interrupt Mask 26 1 read-only ENDRX End of Receive Buffer Interrupt Mask 27 1 read-only RXBUFF Receive Buffer Full Interrupt Mask 28 1 read-only ISR Interrupt Status Register 0x00000030 32 read-only 0x00000000 EOC0 End of Conversion 0 0 1 read-only EOC1 End of Conversion 1 1 1 read-only EOC2 End of Conversion 2 2 1 read-only EOC3 End of Conversion 3 3 1 read-only DRDY Data Ready 24 1 read-only GOVRE General Overrun Error 25 1 read-only COMPE Comparison Error 26 1 read-only ENDRX End of RX Buffer 27 1 read-only RXBUFF RX Buffer Full 28 1 read-only OVER Overrun Status Register 0x0000003C 32 read-only 0x00000000 OVRE0 Overrun Error 0 0 1 read-only OVRE1 Overrun Error 1 1 1 read-only OVRE2 Overrun Error 2 2 1 read-only OVRE3 Overrun Error 3 3 1 read-only EMR Extended Mode Register 0x00000040 32 read-write 0x00000000 CMPMODE Comparison Mode 0 2 read-write LOW Generates an event when the converted data is lower than the low threshold of the window. 0x0 HIGH Generates an event when the converted data is higher than the high threshold of the window. 0x1 IN Generates an event when the converted data is in the comparison window. 0x2 OUT Generates an event when the converted data is out of the comparison window. 0x3 CMPSEL Comparison Selected Channel 4 4 read-write CMPALL Compare All Channels 9 1 read-write TAG TAG of the ADC_LDCR register 24 1 read-write CWR Compare Window Register 0x00000044 32 read-write 0x00000000 LOWTHRES Low Threshold 0 12 read-write HIGHTHRES High Threshold 16 12 read-write 4 4 0-3 CDR[%s] Channel Data Register 0x00000050 32 read-only DATA Converted Data 0 12 read-only WPMR Write Protect Mode Register 0x000000E4 32 read-write 0x00000000 WPEN Write Protect Enable 0 1 read-write WPKEY Write Protect KEY 8 24 read-write WPSR Write Protect Status Register 0x000000E8 32 read-only 0x00000000 WPVS Write Protect Violation Status 0 1 read-only WPVSRC Write Protect Violation Source 8 16 read-only RPR Receive Pointer Register 0x00000100 32 read-write 0x00000000 RXPTR Receive Pointer Register 0 32 read-write RCR Receive Counter Register 0x00000104 32 read-write 0x00000000 RXCTR Receive Counter Register 0 16 read-write RNPR Receive Next Pointer Register 0x00000110 32 read-write 0x00000000 RXNPTR Receive Next Pointer 0 32 read-write RNCR Receive Next Counter Register 0x00000114 32 read-write 0x00000000 RXNCTR Receive Next Counter 0 16 read-write PTCR Transfer Control Register 0x00000120 32 write-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 write-only RXTDIS Receiver Transfer Disable 1 1 write-only TXTEN Transmitter Transfer Enable 8 1 write-only TXTDIS Transmitter Transfer Disable 9 1 write-only PTSR Transfer Status Register 0x00000124 32 read-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 read-only TXTEN Transmitter Transfer Enable 8 1 read-only SDRAMC 6100N SDRAM Controller EBI SDRAMC_ 0xFFFFEA00 0 0x200 registers MR SDRAMC Mode Register 0x00000000 32 read-write 0x00000000 MODE SDRAMC Command Mode 0 3 read-write NORMAL Normal mode. Any access to the SDRAM is decoded normally. To activate this mode, command must be followed by a write to the SDRAM. 0x0 NOP The SDRAM Controller issues a NOP command when the SDRAM device is accessed regardless of the cycle. To activate this mode, command must be followed by a write to the SDRAM. 0x1 ALLBANKS_PRECHARGE The SDRAM Controller issues an "All Banks Precharge" command when the SDRAM device is accessed regardless of the cycle. To activate this mode, command must be followed by a write to the SDRAM. 0x2 LOAD_MODEREG The SDRAM Controller issues a "Load Mode Register" command when the SDRAM device is accessed regardless of the cycle. To activate this mode, command must be followed by a write to the SDRAM. 0x3 AUTO_REFRESH The SDRAM Controller issues an "Auto-Refresh" Command when the SDRAM device is accessed regardless of the cycle. Previously, an "All Banks Precharge" command must be issued. To activate this mode, command must be followed by a write to the SDRAM. 0x4 EXT_LOAD_MODEREG The SDRAM Controller issues an "Extended Load Mode Register" command when the SDRAM device is accessed regardless of the cycle. To activate this mode, the "Extended Load Mode Register" command must be followed by a write to the SDRAM. The write in the SDRAM must be done in the appropriate bank; most low-power SDRAM devices use the bank 1. 0x5 DEEP_POWERDOWN Deep power-down mode. Enters deep power-down mode. 0x6 TR SDRAMC Refresh Timer Register 0x00000004 32 read-write 0x00000000 COUNT SDRAMC Refresh Timer Count 0 12 read-write CR SDRAMC Configuration Register 0x00000008 32 read-write 0x852372C0 NC Number of Column Bits 0 2 read-write COL8 8 column bits 0x0 COL9 9 column bits 0x1 COL10 10 column bits 0x2 COL11 11 column bits 0x3 NR Number of Row Bits 2 2 read-write ROW11 11 row bits 0x0 ROW12 12 row bits 0x1 ROW13 13 row bits 0x2 NB Number of Banks 4 1 read-write BANK2 2 banks 0 BANK4 4 banks 1 CAS CAS Latency 5 2 read-write LATENCY1 1 cycle CAS latency 0x1 LATENCY2 2 cycle CAS latency 0x2 LATENCY3 3 cycle CAS latency 0x3 DBW Data Bus Width 7 1 read-write TWR Write Recovery Delay 8 4 read-write TRC_TRFC Row Cycle Delay and Row Refresh Cycle 12 4 read-write TRP Row Precharge Delay 16 4 read-write TRCD Row to Column Delay 20 4 read-write TRAS Active to Precharge Delay 24 4 read-write TXSR Exit Self Refresh to Active Delay 28 4 read-write LPR SDRAMC Low Power Register 0x00000010 32 read-write 0x00000000 LPCB Low-power Configuration Bits 0 2 read-write DISABLED Low Power Feature is inhibited: no Power-down, Self-refresh or Deep Power-down command is issued to the SDRAM device. 0x0 SELF_REFRESH The SDRAM Controller issues a Self-refresh command to the SDRAM device, the SDCK clock is deactivated and the SDCKE signal is set low. The SDRAM device leaves the Self Refresh Mode when accessed and enters it after the access. 0x1 POWER_DOWN The SDRAM Controller issues a Power-down Command to the SDRAM device after each access, the SDCKE signal is set to low. The SDRAM device leaves the Power-down Mode when accessed and enters it after the access. 0x2 DEEP_POWER_DOWN The SDRAM Controller issues a Deep Power-down command to the SDRAM device. This mode is unique to low-power SDRAM. 0x3 PASR Partial Array Self-refresh (only for low-power SDRAM) 4 3 read-write TCSR Temperature Compensated Self-Refresh (only for low-power SDRAM) 8 2 read-write DS Drive Strength (only for low-power SDRAM) 10 2 read-write TIMEOUT Time to define when low-power mode is enable 12 2 read-write LP_LAST_XFER The SDRAM controller activates the SDRAM low-power mode immediately after the end of the last transfer. 0x0 LP_LAST_XFER_64 The SDRAM controller activates the SDRAM low-power mode 64 clock cycles after the end of the last transfer. 0x1 LP_LAST_XFER_128 The SDRAM controller activates the SDRAM low-power mode 128 clock cycles after the end of the last transfer. 0x2 IER SDRAMC Interrupt Enable Register 0x00000014 32 write-only RES Refresh Error Status 0 1 write-only IDR SDRAMC Interrupt Disable Register 0x00000018 32 write-only RES Refresh Error Status 0 1 write-only IMR SDRAMC Interrupt Mask Register 0x0000001C 32 read-only 0x00000000 RES Refresh Error Status 0 1 read-only ISR SDRAMC Interrupt Status Register 0x00000020 32 read-only 0x00000000 RES Refresh Error Status 0 1 read-only MDR SDRAMC Memory Device Register 0x00000024 32 read-write 0x00000000 MD Memory Device Type 0 2 read-write SDRAM SDRAM 0x0 LPSDRAM Low-power SDRAM 0x1 SMC 6105J Static Memory Controller EBI SMC_ 0xFFFFEC00 0 0x200 registers SETUP0 SMC Setup Register (CS_number = 0) 0x00000000 32 read-write NWE_SETUP NWE Setup Length 0 6 read-write NCS_WR_SETUP NCS Setup Length in WRITE Access 8 6 read-write NRD_SETUP NRD Setup Length 16 6 read-write NCS_RD_SETUP NCS Setup Length in READ Access 24 6 read-write PULSE0 SMC Pulse Register (CS_number = 0) 0x00000004 32 read-write 0x01010101 NWE_PULSE NWE Pulse Length 0 7 read-write NCS_WR_PULSE NCS Pulse Length in WRITE Access 8 7 read-write NRD_PULSE NRD Pulse Length 16 7 read-write NCS_RD_PULSE NCS Pulse Length in READ Access 24 7 read-write CYCLE0 SMC Cycle Register (CS_number = 0) 0x00000008 32 read-write 0x00010001 NWE_CYCLE Total Write Cycle Length 0 9 read-write NRD_CYCLE Total Read Cycle Length 16 9 read-write MODE0 SMC Mode Register (CS_number = 0) 0x0000000C 32 read-write 0x10001000 READ_MODE 0 1 read-write WRITE_MODE 1 1 read-write EXNW_MODE NWAIT Mode 4 2 read-write BAT Byte Access Type 8 1 read-write DBW Data Bus Width 12 2 read-write TDF_CYCLES Data Float Time 16 4 read-write TDF_MODE TDF Optimization 20 1 read-write PMEN Page Mode Enabled 24 1 read-write PS Page Size 28 2 read-write SETUP1 SMC Setup Register (CS_number = 1) 0x00000010 32 read-write NWE_SETUP NWE Setup Length 0 6 read-write NCS_WR_SETUP NCS Setup Length in WRITE Access 8 6 read-write NRD_SETUP NRD Setup Length 16 6 read-write NCS_RD_SETUP NCS Setup Length in READ Access 24 6 read-write PULSE1 SMC Pulse Register (CS_number = 1) 0x00000014 32 read-write 0x01010101 NWE_PULSE NWE Pulse Length 0 7 read-write NCS_WR_PULSE NCS Pulse Length in WRITE Access 8 7 read-write NRD_PULSE NRD Pulse Length 16 7 read-write NCS_RD_PULSE NCS Pulse Length in READ Access 24 7 read-write CYCLE1 SMC Cycle Register (CS_number = 1) 0x00000018 32 read-write 0x00010001 NWE_CYCLE Total Write Cycle Length 0 9 read-write NRD_CYCLE Total Read Cycle Length 16 9 read-write MODE1 SMC Mode Register (CS_number = 1) 0x0000001C 32 read-write 0x10001000 READ_MODE 0 1 read-write WRITE_MODE 1 1 read-write EXNW_MODE NWAIT Mode 4 2 read-write BAT Byte Access Type 8 1 read-write DBW Data Bus Width 12 2 read-write TDF_CYCLES Data Float Time 16 4 read-write TDF_MODE TDF Optimization 20 1 read-write PMEN Page Mode Enabled 24 1 read-write PS Page Size 28 2 read-write SETUP2 SMC Setup Register (CS_number = 2) 0x00000020 32 read-write NWE_SETUP NWE Setup Length 0 6 read-write NCS_WR_SETUP NCS Setup Length in WRITE Access 8 6 read-write NRD_SETUP NRD Setup Length 16 6 read-write NCS_RD_SETUP NCS Setup Length in READ Access 24 6 read-write PULSE2 SMC Pulse Register (CS_number = 2) 0x00000024 32 read-write 0x01010101 NWE_PULSE NWE Pulse Length 0 7 read-write NCS_WR_PULSE NCS Pulse Length in WRITE Access 8 7 read-write NRD_PULSE NRD Pulse Length 16 7 read-write NCS_RD_PULSE NCS Pulse Length in READ Access 24 7 read-write CYCLE2 SMC Cycle Register (CS_number = 2) 0x00000028 32 read-write 0x00010001 NWE_CYCLE Total Write Cycle Length 0 9 read-write NRD_CYCLE Total Read Cycle Length 16 9 read-write MODE2 SMC Mode Register (CS_number = 2) 0x0000002C 32 read-write 0x10001000 READ_MODE 0 1 read-write WRITE_MODE 1 1 read-write EXNW_MODE NWAIT Mode 4 2 read-write BAT Byte Access Type 8 1 read-write DBW Data Bus Width 12 2 read-write TDF_CYCLES Data Float Time 16 4 read-write TDF_MODE TDF Optimization 20 1 read-write PMEN Page Mode Enabled 24 1 read-write PS Page Size 28 2 read-write SETUP3 SMC Setup Register (CS_number = 3) 0x00000030 32 read-write NWE_SETUP NWE Setup Length 0 6 read-write NCS_WR_SETUP NCS Setup Length in WRITE Access 8 6 read-write NRD_SETUP NRD Setup Length 16 6 read-write NCS_RD_SETUP NCS Setup Length in READ Access 24 6 read-write PULSE3 SMC Pulse Register (CS_number = 3) 0x00000034 32 read-write 0x01010101 NWE_PULSE NWE Pulse Length 0 7 read-write NCS_WR_PULSE NCS Pulse Length in WRITE Access 8 7 read-write NRD_PULSE NRD Pulse Length 16 7 read-write NCS_RD_PULSE NCS Pulse Length in READ Access 24 7 read-write CYCLE3 SMC Cycle Register (CS_number = 3) 0x00000038 32 read-write 0x00010001 NWE_CYCLE Total Write Cycle Length 0 9 read-write NRD_CYCLE Total Read Cycle Length 16 9 read-write MODE3 SMC Mode Register (CS_number = 3) 0x0000003C 32 read-write 0x10001000 READ_MODE 0 1 read-write WRITE_MODE 1 1 read-write EXNW_MODE NWAIT Mode 4 2 read-write BAT Byte Access Type 8 1 read-write DBW Data Bus Width 12 2 read-write TDF_CYCLES Data Float Time 16 4 read-write TDF_MODE TDF Optimization 20 1 read-write PMEN Page Mode Enabled 24 1 read-write PS Page Size 28 2 read-write SETUP4 SMC Setup Register (CS_number = 4) 0x00000040 32 read-write NWE_SETUP NWE Setup Length 0 6 read-write NCS_WR_SETUP NCS Setup Length in WRITE Access 8 6 read-write NRD_SETUP NRD Setup Length 16 6 read-write NCS_RD_SETUP NCS Setup Length in READ Access 24 6 read-write PULSE4 SMC Pulse Register (CS_number = 4) 0x00000044 32 read-write 0x01010101 NWE_PULSE NWE Pulse Length 0 7 read-write NCS_WR_PULSE NCS Pulse Length in WRITE Access 8 7 read-write NRD_PULSE NRD Pulse Length 16 7 read-write NCS_RD_PULSE NCS Pulse Length in READ Access 24 7 read-write CYCLE4 SMC Cycle Register (CS_number = 4) 0x00000048 32 read-write 0x00010001 NWE_CYCLE Total Write Cycle Length 0 9 read-write NRD_CYCLE Total Read Cycle Length 16 9 read-write MODE4 SMC Mode Register (CS_number = 4) 0x0000004C 32 read-write 0x10001000 READ_MODE 0 1 read-write WRITE_MODE 1 1 read-write EXNW_MODE NWAIT Mode 4 2 read-write BAT Byte Access Type 8 1 read-write DBW Data Bus Width 12 2 read-write TDF_CYCLES Data Float Time 16 4 read-write TDF_MODE TDF Optimization 20 1 read-write PMEN Page Mode Enabled 24 1 read-write PS Page Size 28 2 read-write SETUP5 SMC Setup Register (CS_number = 5) 0x00000050 32 read-write NWE_SETUP NWE Setup Length 0 6 read-write NCS_WR_SETUP NCS Setup Length in WRITE Access 8 6 read-write NRD_SETUP NRD Setup Length 16 6 read-write NCS_RD_SETUP NCS Setup Length in READ Access 24 6 read-write PULSE5 SMC Pulse Register (CS_number = 5) 0x00000054 32 read-write 0x01010101 NWE_PULSE NWE Pulse Length 0 7 read-write NCS_WR_PULSE NCS Pulse Length in WRITE Access 8 7 read-write NRD_PULSE NRD Pulse Length 16 7 read-write NCS_RD_PULSE NCS Pulse Length in READ Access 24 7 read-write CYCLE5 SMC Cycle Register (CS_number = 5) 0x00000058 32 read-write 0x00010001 NWE_CYCLE Total Write Cycle Length 0 9 read-write NRD_CYCLE Total Read Cycle Length 16 9 read-write MODE5 SMC Mode Register (CS_number = 5) 0x0000005C 32 read-write 0x10001000 READ_MODE 0 1 read-write WRITE_MODE 1 1 read-write EXNW_MODE NWAIT Mode 4 2 read-write BAT Byte Access Type 8 1 read-write DBW Data Bus Width 12 2 read-write TDF_CYCLES Data Float Time 16 4 read-write TDF_MODE TDF Optimization 20 1 read-write PMEN Page Mode Enabled 24 1 read-write PS Page Size 28 2 read-write SETUP6 SMC Setup Register (CS_number = 6) 0x00000060 32 read-write NWE_SETUP NWE Setup Length 0 6 read-write NCS_WR_SETUP NCS Setup Length in WRITE Access 8 6 read-write NRD_SETUP NRD Setup Length 16 6 read-write NCS_RD_SETUP NCS Setup Length in READ Access 24 6 read-write PULSE6 SMC Pulse Register (CS_number = 6) 0x00000064 32 read-write 0x01010101 NWE_PULSE NWE Pulse Length 0 7 read-write NCS_WR_PULSE NCS Pulse Length in WRITE Access 8 7 read-write NRD_PULSE NRD Pulse Length 16 7 read-write NCS_RD_PULSE NCS Pulse Length in READ Access 24 7 read-write CYCLE6 SMC Cycle Register (CS_number = 6) 0x00000068 32 read-write 0x00010001 NWE_CYCLE Total Write Cycle Length 0 9 read-write NRD_CYCLE Total Read Cycle Length 16 9 read-write MODE6 SMC Mode Register (CS_number = 6) 0x0000006C 32 read-write 0x10001000 READ_MODE 0 1 read-write WRITE_MODE 1 1 read-write EXNW_MODE NWAIT Mode 4 2 read-write BAT Byte Access Type 8 1 read-write DBW Data Bus Width 12 2 read-write TDF_CYCLES Data Float Time 16 4 read-write TDF_MODE TDF Optimization 20 1 read-write PMEN Page Mode Enabled 24 1 read-write PS Page Size 28 2 read-write SETUP7 SMC Setup Register (CS_number = 7) 0x00000070 32 read-write NWE_SETUP NWE Setup Length 0 6 read-write NCS_WR_SETUP NCS Setup Length in WRITE Access 8 6 read-write NRD_SETUP NRD Setup Length 16 6 read-write NCS_RD_SETUP NCS Setup Length in READ Access 24 6 read-write PULSE7 SMC Pulse Register (CS_number = 7) 0x00000074 32 read-write 0x01010101 NWE_PULSE NWE Pulse Length 0 7 read-write NCS_WR_PULSE NCS Pulse Length in WRITE Access 8 7 read-write NRD_PULSE NRD Pulse Length 16 7 read-write NCS_RD_PULSE NCS Pulse Length in READ Access 24 7 read-write CYCLE7 SMC Cycle Register (CS_number = 7) 0x00000078 32 read-write 0x00010001 NWE_CYCLE Total Write Cycle Length 0 9 read-write NRD_CYCLE Total Read Cycle Length 16 9 read-write MODE7 SMC Mode Register (CS_number = 7) 0x0000007C 32 read-write 0x10001000 READ_MODE 0 1 read-write WRITE_MODE 1 1 read-write EXNW_MODE NWAIT Mode 4 2 read-write BAT Byte Access Type 8 1 read-write DBW Data Bus Width 12 2 read-write TDF_CYCLES Data Float Time 16 4 read-write TDF_MODE TDF Optimization 20 1 read-write PMEN Page Mode Enabled 24 1 read-write PS Page Size 28 2 read-write MATRIX 6346A AHB Bus Matrix 0xFFFFEE00 0 0x200 registers 6 4 0-5 MATRIX_MCFG[%s] Master Configuration Register 0x00000000 32 read-write ULBT Undefined Length Burst Type 0 3 read-write 5 4 0-4 MATRIX_SCFG[%s] Slave Configuration Register 0x00000040 32 read-write SLOT_CYCLE Maximum Number of Allowed Cycles for a Burst 0 8 read-write DEFMSTR_TYPE Default Master Type 16 2 read-write FIXED_DEFMSTR Fixed Default Master 18 3 read-write ARBT Arbitration Type 24 2 read-write MATRIX_PRAS0 Priority Register A for Slave 0 0x00000080 32 read-write 0x00000000 M0PR Master 0 Priority 0 2 read-write M1PR Master 1 Priority 4 2 read-write M2PR Master 2 Priority 8 2 read-write M3PR Master 3 Priority 12 2 read-write M4PR Master 4 Priority 16 2 read-write M5PR Master 5 Priority 20 2 read-write MATRIX_PRAS1 Priority Register A for Slave 1 0x00000088 32 read-write 0x00000000 M0PR Master 0 Priority 0 2 read-write M1PR Master 1 Priority 4 2 read-write M2PR Master 2 Priority 8 2 read-write M3PR Master 3 Priority 12 2 read-write M4PR Master 4 Priority 16 2 read-write M5PR Master 5 Priority 20 2 read-write MATRIX_PRAS2 Priority Register A for Slave 2 0x00000090 32 read-write 0x00000000 M0PR Master 0 Priority 0 2 read-write M1PR Master 1 Priority 4 2 read-write M2PR Master 2 Priority 8 2 read-write M3PR Master 3 Priority 12 2 read-write M4PR Master 4 Priority 16 2 read-write M5PR Master 5 Priority 20 2 read-write MATRIX_PRAS3 Priority Register A for Slave 3 0x00000098 32 read-write 0x00000000 M0PR Master 0 Priority 0 2 read-write M1PR Master 1 Priority 4 2 read-write M2PR Master 2 Priority 8 2 read-write M3PR Master 3 Priority 12 2 read-write M4PR Master 4 Priority 16 2 read-write M5PR Master 5 Priority 20 2 read-write MATRIX_PRAS4 Priority Register A for Slave 4 0x000000A0 32 read-write 0x00000000 M0PR Master 0 Priority 0 2 read-write M1PR Master 1 Priority 4 2 read-write M2PR Master 2 Priority 8 2 read-write M3PR Master 3 Priority 12 2 read-write M4PR Master 4 Priority 16 2 read-write M5PR Master 5 Priority 20 2 read-write MATRIX_MRCR Master Remap Control Register 0x00000100 32 read-write 0x00000000 RCB0 Remap Command Bit for AHB Master 0 0 1 read-write RCB1 Remap Command Bit for AHB Master 1 1 1 read-write EBI_CSA EBI Chip Select Assignment Register 0x0000011C 32 read-write 0x00010000 EBI_CS1A EBI Chip Select 1 Assignment 1 1 read-write EBI_CS3A EBI Chip Select 3 Assignment 3 1 read-write EBI_CS4A EBI Chip Select 4 Assignment 4 1 read-write EBI_CS5A EBI Chip Select 5 Assignment 5 1 read-write EBI_DBPUC EBI Data Bus Pull-Up Configuration 8 1 read-write VDDIOMSEL Memory voltage selection 16 1 read-write IOSR I/O Slew Rate Selection 17 1 read-write AIC 6075H Advanced Interrupt Controller AIC_ 0xFFFFF000 0 0x200 registers FIQ 0 IRQ0 29 IRQ1 30 IRQ2 31 32 4 0-31 SMR[%s] Source Mode Register 0x00000000 32 read-write PRIOR Priority Level 0 3 read-write SRCTYPE Interrupt Source Type 5 2 read-write INT_LEVEL_SENSITIVE High level Sensitive for internal sourceLow level Sensitive for external source 0x0 INT_EDGE_TRIGGERED Positive edge triggered for internal sourceNegative edge triggered for external source 0x1 EXT_HIGH_LEVEL High level Sensitive for internal sourceHigh level Sensitive for external source 0x2 EXT_POSITIVE_EDGE Positive edge triggered for internal sourcePositive edge triggered for external source 0x3 32 4 0-31 SVR[%s] Source Vector Register 0x00000080 32 read-write VECTOR Source Vector 0 32 read-write IVR Interrupt Vector Register 0x00000100 32 read-only 0x00000000 IRQV Interrupt Vector Register 0 32 read-only FVR FIQ Interrupt Vector Register 0x00000104 32 read-only 0x00000000 FIQV FIQ Vector Register 0 32 read-only ISR Interrupt Status Register 0x00000108 32 read-only 0x00000000 IRQID Current Interrupt Identifier 0 5 read-only IPR Interrupt Pending Register 0x0000010C 32 read-only 0x00000000 FIQ Interrupt Pending 0 1 read-only SYS Interrupt Pending 1 1 read-only PID2 Interrupt Pending 2 1 read-only PID3 Interrupt Pending 3 1 read-only PID4 Interrupt Pending 4 1 read-only PID5 Interrupt Pending 5 1 read-only PID6 Interrupt Pending 6 1 read-only PID7 Interrupt Pending 7 1 read-only PID8 Interrupt Pending 8 1 read-only PID9 Interrupt Pending 9 1 read-only PID10 Interrupt Pending 10 1 read-only PID11 Interrupt Pending 11 1 read-only PID12 Interrupt Pending 12 1 read-only PID13 Interrupt Pending 13 1 read-only PID14 Interrupt Pending 14 1 read-only PID15 Interrupt Pending 15 1 read-only PID16 Interrupt Pending 16 1 read-only PID17 Interrupt Pending 17 1 read-only PID18 Interrupt Pending 18 1 read-only PID19 Interrupt Pending 19 1 read-only PID20 Interrupt Pending 20 1 read-only PID21 Interrupt Pending 21 1 read-only PID22 Interrupt Pending 22 1 read-only PID23 Interrupt Pending 23 1 read-only PID24 Interrupt Pending 24 1 read-only PID25 Interrupt Pending 25 1 read-only PID26 Interrupt Pending 26 1 read-only PID27 Interrupt Pending 27 1 read-only PID28 Interrupt Pending 28 1 read-only PID29 Interrupt Pending 29 1 read-only PID30 Interrupt Pending 30 1 read-only PID31 Interrupt Pending 31 1 read-only IMR Interrupt Mask Register 0x00000110 32 read-only 0x00000000 FIQ Interrupt Mask 0 1 read-only SYS Interrupt Mask 1 1 read-only PID2 Interrupt Mask 2 1 read-only PID3 Interrupt Mask 3 1 read-only PID4 Interrupt Mask 4 1 read-only PID5 Interrupt Mask 5 1 read-only PID6 Interrupt Mask 6 1 read-only PID7 Interrupt Mask 7 1 read-only PID8 Interrupt Mask 8 1 read-only PID9 Interrupt Mask 9 1 read-only PID10 Interrupt Mask 10 1 read-only PID11 Interrupt Mask 11 1 read-only PID12 Interrupt Mask 12 1 read-only PID13 Interrupt Mask 13 1 read-only PID14 Interrupt Mask 14 1 read-only PID15 Interrupt Mask 15 1 read-only PID16 Interrupt Mask 16 1 read-only PID17 Interrupt Mask 17 1 read-only PID18 Interrupt Mask 18 1 read-only PID19 Interrupt Mask 19 1 read-only PID20 Interrupt Mask 20 1 read-only PID21 Interrupt Mask 21 1 read-only PID22 Interrupt Mask 22 1 read-only PID23 Interrupt Mask 23 1 read-only PID24 Interrupt Mask 24 1 read-only PID25 Interrupt Mask 25 1 read-only PID26 Interrupt Mask 26 1 read-only PID27 Interrupt Mask 27 1 read-only PID28 Interrupt Mask 28 1 read-only PID29 Interrupt Mask 29 1 read-only PID30 Interrupt Mask 30 1 read-only PID31 Interrupt Mask 31 1 read-only CISR Core Interrupt Status Register 0x00000114 32 read-only 0x00000000 NFIQ NFIQ Status 0 1 read-only NIRQ NIRQ Status 1 1 read-only IECR Interrupt Enable Command Register 0x00000120 32 write-only FIQ Interrupt Enable 0 1 write-only SYS Interrupt Enable 1 1 write-only PID2 Interrupt Enable 2 1 write-only PID3 Interrupt Enable 3 1 write-only PID4 Interrupt Enable 4 1 write-only PID5 Interrupt Enable 5 1 write-only PID6 Interrupt Enable 6 1 write-only PID7 Interrupt Enable 7 1 write-only PID8 Interrupt Enable 8 1 write-only PID9 Interrupt Enable 9 1 write-only PID10 Interrupt Enable 10 1 write-only PID11 Interrupt Enable 11 1 write-only PID12 Interrupt Enable 12 1 write-only PID13 Interrupt Enable 13 1 write-only PID14 Interrupt Enable 14 1 write-only PID15 Interrupt Enable 15 1 write-only PID16 Interrupt Enable 16 1 write-only PID17 Interrupt Enable 17 1 write-only PID18 Interrupt Enable 18 1 write-only PID19 Interrupt Enable 19 1 write-only PID20 Interrupt Enable 20 1 write-only PID21 Interrupt Enable 21 1 write-only PID22 Interrupt Enable 22 1 write-only PID23 Interrupt Enable 23 1 write-only PID24 Interrupt Enable 24 1 write-only PID25 Interrupt Enable 25 1 write-only PID26 Interrupt Enable 26 1 write-only PID27 Interrupt Enable 27 1 write-only PID28 Interrupt Enable 28 1 write-only PID29 Interrupt Enable 29 1 write-only PID30 Interrupt Enable 30 1 write-only PID31 Interrupt Enable 31 1 write-only IDCR Interrupt Disable Command Register 0x00000124 32 write-only FIQ Interrupt Disable 0 1 write-only SYS Interrupt Disable 1 1 write-only PID2 Interrupt Disable 2 1 write-only PID3 Interrupt Disable 3 1 write-only PID4 Interrupt Disable 4 1 write-only PID5 Interrupt Disable 5 1 write-only PID6 Interrupt Disable 6 1 write-only PID7 Interrupt Disable 7 1 write-only PID8 Interrupt Disable 8 1 write-only PID9 Interrupt Disable 9 1 write-only PID10 Interrupt Disable 10 1 write-only PID11 Interrupt Disable 11 1 write-only PID12 Interrupt Disable 12 1 write-only PID13 Interrupt Disable 13 1 write-only PID14 Interrupt Disable 14 1 write-only PID15 Interrupt Disable 15 1 write-only PID16 Interrupt Disable 16 1 write-only PID17 Interrupt Disable 17 1 write-only PID18 Interrupt Disable 18 1 write-only PID19 Interrupt Disable 19 1 write-only PID20 Interrupt Disable 20 1 write-only PID21 Interrupt Disable 21 1 write-only PID22 Interrupt Disable 22 1 write-only PID23 Interrupt Disable 23 1 write-only PID24 Interrupt Disable 24 1 write-only PID25 Interrupt Disable 25 1 write-only PID26 Interrupt Disable 26 1 write-only PID27 Interrupt Disable 27 1 write-only PID28 Interrupt Disable 28 1 write-only PID29 Interrupt Disable 29 1 write-only PID30 Interrupt Disable 30 1 write-only PID31 Interrupt Disable 31 1 write-only ICCR Interrupt Clear Command Register 0x00000128 32 write-only FIQ Interrupt Clear 0 1 write-only SYS Interrupt Clear 1 1 write-only PID2 Interrupt Clear 2 1 write-only PID3 Interrupt Clear 3 1 write-only PID4 Interrupt Clear 4 1 write-only PID5 Interrupt Clear 5 1 write-only PID6 Interrupt Clear 6 1 write-only PID7 Interrupt Clear 7 1 write-only PID8 Interrupt Clear 8 1 write-only PID9 Interrupt Clear 9 1 write-only PID10 Interrupt Clear 10 1 write-only PID11 Interrupt Clear 11 1 write-only PID12 Interrupt Clear 12 1 write-only PID13 Interrupt Clear 13 1 write-only PID14 Interrupt Clear 14 1 write-only PID15 Interrupt Clear 15 1 write-only PID16 Interrupt Clear 16 1 write-only PID17 Interrupt Clear 17 1 write-only PID18 Interrupt Clear 18 1 write-only PID19 Interrupt Clear 19 1 write-only PID20 Interrupt Clear 20 1 write-only PID21 Interrupt Clear 21 1 write-only PID22 Interrupt Clear 22 1 write-only PID23 Interrupt Clear 23 1 write-only PID24 Interrupt Clear 24 1 write-only PID25 Interrupt Clear 25 1 write-only PID26 Interrupt Clear 26 1 write-only PID27 Interrupt Clear 27 1 write-only PID28 Interrupt Clear 28 1 write-only PID29 Interrupt Clear 29 1 write-only PID30 Interrupt Clear 30 1 write-only PID31 Interrupt Clear 31 1 write-only ISCR Interrupt Set Command Register 0x0000012C 32 write-only FIQ Interrupt Set 0 1 write-only SYS Interrupt Set 1 1 write-only PID2 Interrupt Set 2 1 write-only PID3 Interrupt Set 3 1 write-only PID4 Interrupt Set 4 1 write-only PID5 Interrupt Set 5 1 write-only PID6 Interrupt Set 6 1 write-only PID7 Interrupt Set 7 1 write-only PID8 Interrupt Set 8 1 write-only PID9 Interrupt Set 9 1 write-only PID10 Interrupt Set 10 1 write-only PID11 Interrupt Set 11 1 write-only PID12 Interrupt Set 12 1 write-only PID13 Interrupt Set 13 1 write-only PID14 Interrupt Set 14 1 write-only PID15 Interrupt Set 15 1 write-only PID16 Interrupt Set 16 1 write-only PID17 Interrupt Set 17 1 write-only PID18 Interrupt Set 18 1 write-only PID19 Interrupt Set 19 1 write-only PID20 Interrupt Set 20 1 write-only PID21 Interrupt Set 21 1 write-only PID22 Interrupt Set 22 1 write-only PID23 Interrupt Set 23 1 write-only PID24 Interrupt Set 24 1 write-only PID25 Interrupt Set 25 1 write-only PID26 Interrupt Set 26 1 write-only PID27 Interrupt Set 27 1 write-only PID28 Interrupt Set 28 1 write-only PID29 Interrupt Set 29 1 write-only PID30 Interrupt Set 30 1 write-only PID31 Interrupt Set 31 1 write-only EOICR End of Interrupt Command Register 0x00000130 32 write-only SPU Spurious Interrupt Vector Register 0x00000134 32 read-write 0x00000000 SIVR Spurious Interrupt Vector Register 0 32 read-write DCR Debug Control Register 0x00000138 32 read-write 0x00000000 PROT Protection Mode 0 1 read-write GMSK General Mask 1 1 read-write FFER Fast Forcing Enable Register 0x00000140 32 write-only SYS Fast Forcing Enable 1 1 write-only PID2 Fast Forcing Enable 2 1 write-only PID3 Fast Forcing Enable 3 1 write-only PID4 Fast Forcing Enable 4 1 write-only PID5 Fast Forcing Enable 5 1 write-only PID6 Fast Forcing Enable 6 1 write-only PID7 Fast Forcing Enable 7 1 write-only PID8 Fast Forcing Enable 8 1 write-only PID9 Fast Forcing Enable 9 1 write-only PID10 Fast Forcing Enable 10 1 write-only PID11 Fast Forcing Enable 11 1 write-only PID12 Fast Forcing Enable 12 1 write-only PID13 Fast Forcing Enable 13 1 write-only PID14 Fast Forcing Enable 14 1 write-only PID15 Fast Forcing Enable 15 1 write-only PID16 Fast Forcing Enable 16 1 write-only PID17 Fast Forcing Enable 17 1 write-only PID18 Fast Forcing Enable 18 1 write-only PID19 Fast Forcing Enable 19 1 write-only PID20 Fast Forcing Enable 20 1 write-only PID21 Fast Forcing Enable 21 1 write-only PID22 Fast Forcing Enable 22 1 write-only PID23 Fast Forcing Enable 23 1 write-only PID24 Fast Forcing Enable 24 1 write-only PID25 Fast Forcing Enable 25 1 write-only PID26 Fast Forcing Enable 26 1 write-only PID27 Fast Forcing Enable 27 1 write-only PID28 Fast Forcing Enable 28 1 write-only PID29 Fast Forcing Enable 29 1 write-only PID30 Fast Forcing Enable 30 1 write-only PID31 Fast Forcing Enable 31 1 write-only FFDR Fast Forcing Disable Register 0x00000144 32 write-only SYS Fast Forcing Disable 1 1 write-only PID2 Fast Forcing Disable 2 1 write-only PID3 Fast Forcing Disable 3 1 write-only PID4 Fast Forcing Disable 4 1 write-only PID5 Fast Forcing Disable 5 1 write-only PID6 Fast Forcing Disable 6 1 write-only PID7 Fast Forcing Disable 7 1 write-only PID8 Fast Forcing Disable 8 1 write-only PID9 Fast Forcing Disable 9 1 write-only PID10 Fast Forcing Disable 10 1 write-only PID11 Fast Forcing Disable 11 1 write-only PID12 Fast Forcing Disable 12 1 write-only PID13 Fast Forcing Disable 13 1 write-only PID14 Fast Forcing Disable 14 1 write-only PID15 Fast Forcing Disable 15 1 write-only PID16 Fast Forcing Disable 16 1 write-only PID17 Fast Forcing Disable 17 1 write-only PID18 Fast Forcing Disable 18 1 write-only PID19 Fast Forcing Disable 19 1 write-only PID20 Fast Forcing Disable 20 1 write-only PID21 Fast Forcing Disable 21 1 write-only PID22 Fast Forcing Disable 22 1 write-only PID23 Fast Forcing Disable 23 1 write-only PID24 Fast Forcing Disable 24 1 write-only PID25 Fast Forcing Disable 25 1 write-only PID26 Fast Forcing Disable 26 1 write-only PID27 Fast Forcing Disable 27 1 write-only PID28 Fast Forcing Disable 28 1 write-only PID29 Fast Forcing Disable 29 1 write-only PID30 Fast Forcing Disable 30 1 write-only PID31 Fast Forcing Disable 31 1 write-only FFSR Fast Forcing Status Register 0x00000148 32 read-only 0x00000000 SYS Fast Forcing Status 1 1 read-only PID2 Fast Forcing Status 2 1 read-only PID3 Fast Forcing Status 3 1 read-only PID4 Fast Forcing Status 4 1 read-only PID5 Fast Forcing Status 5 1 read-only PID6 Fast Forcing Status 6 1 read-only PID7 Fast Forcing Status 7 1 read-only PID8 Fast Forcing Status 8 1 read-only PID9 Fast Forcing Status 9 1 read-only PID10 Fast Forcing Status 10 1 read-only PID11 Fast Forcing Status 11 1 read-only PID12 Fast Forcing Status 12 1 read-only PID13 Fast Forcing Status 13 1 read-only PID14 Fast Forcing Status 14 1 read-only PID15 Fast Forcing Status 15 1 read-only PID16 Fast Forcing Status 16 1 read-only PID17 Fast Forcing Status 17 1 read-only PID18 Fast Forcing Status 18 1 read-only PID19 Fast Forcing Status 19 1 read-only PID20 Fast Forcing Status 20 1 read-only PID21 Fast Forcing Status 21 1 read-only PID22 Fast Forcing Status 22 1 read-only PID23 Fast Forcing Status 23 1 read-only PID24 Fast Forcing Status 24 1 read-only PID25 Fast Forcing Status 25 1 read-only PID26 Fast Forcing Status 26 1 read-only PID27 Fast Forcing Status 27 1 read-only PID28 Fast Forcing Status 28 1 read-only PID29 Fast Forcing Status 29 1 read-only PID30 Fast Forcing Status 30 1 read-only PID31 Fast Forcing Status 31 1 read-only DBGU 6059M Debug Unit DBGU_ 0xFFFFF200 0 0x200 registers DBGU 1 CR Control Register 0x00000000 32 write-only RSTRX Reset Receiver 2 1 write-only RSTTX Reset Transmitter 3 1 write-only RXEN Receiver Enable 4 1 write-only RXDIS Receiver Disable 5 1 write-only TXEN Transmitter Enable 6 1 write-only TXDIS Transmitter Disable 7 1 write-only RSTSTA Reset Status Bits 8 1 write-only MR Mode Register 0x00000004 32 read-write 0x00000000 PAR Parity Type 9 3 read-write EVEN Even Parity 0x0 ODD Odd Parity 0x1 SPACE Space: Parity forced to 0 0x2 MARK Mark: Parity forced to 1 0x3 NONE No Parity 0x4 CHMODE Channel Mode 14 2 read-write NORM Normal Mode 0x0 AUTO Automatic Echo 0x1 LOCLOOP Local Loopback 0x2 REMLOOP Remote Loopback 0x3 IER Interrupt Enable Register 0x00000008 32 write-only RXRDY Enable RXRDY Interrupt 0 1 write-only TXRDY Enable TXRDY Interrupt 1 1 write-only ENDRX Enable End of Receive Transfer Interrupt 3 1 write-only ENDTX Enable End of Transmit Interrupt 4 1 write-only OVRE Enable Overrun Error Interrupt 5 1 write-only FRAME Enable Framing Error Interrupt 6 1 write-only PARE Enable Parity Error Interrupt 7 1 write-only TXEMPTY Enable TXEMPTY Interrupt 9 1 write-only TXBUFE Enable Buffer Empty Interrupt 11 1 write-only RXBUFF Enable Buffer Full Interrupt 12 1 write-only COMMTX Enable COMMTX (from ARM) Interrupt 30 1 write-only COMMRX Enable COMMRX (from ARM) Interrupt 31 1 write-only IDR Interrupt Disable Register 0x0000000C 32 write-only RXRDY Disable RXRDY Interrupt 0 1 write-only TXRDY Disable TXRDY Interrupt 1 1 write-only ENDRX Disable End of Receive Transfer Interrupt 3 1 write-only ENDTX Disable End of Transmit Interrupt 4 1 write-only OVRE Disable Overrun Error Interrupt 5 1 write-only FRAME Disable Framing Error Interrupt 6 1 write-only PARE Disable Parity Error Interrupt 7 1 write-only TXEMPTY Disable TXEMPTY Interrupt 9 1 write-only TXBUFE Disable Buffer Empty Interrupt 11 1 write-only RXBUFF Disable Buffer Full Interrupt 12 1 write-only COMMTX Disable COMMTX (from ARM) Interrupt 30 1 write-only COMMRX Disable COMMRX (from ARM) Interrupt 31 1 write-only IMR Interrupt Mask Register 0x00000010 32 read-only 0x00000000 RXRDY Mask RXRDY Interrupt 0 1 read-only TXRDY Disable TXRDY Interrupt 1 1 read-only ENDRX Mask End of Receive Transfer Interrupt 3 1 read-only ENDTX Mask End of Transmit Interrupt 4 1 read-only OVRE Mask Overrun Error Interrupt 5 1 read-only FRAME Mask Framing Error Interrupt 6 1 read-only PARE Mask Parity Error Interrupt 7 1 read-only TXEMPTY Mask TXEMPTY Interrupt 9 1 read-only TXBUFE Mask TXBUFE Interrupt 11 1 read-only RXBUFF Mask RXBUFF Interrupt 12 1 read-only COMMTX Mask COMMTX Interrupt 30 1 read-only COMMRX Mask COMMRX Interrupt 31 1 read-only SR Status Register 0x00000014 32 read-only RXRDY Receiver Ready 0 1 read-only TXRDY Transmitter Ready 1 1 read-only ENDRX End of Receiver Transfer 3 1 read-only ENDTX End of Transmitter Transfer 4 1 read-only OVRE Overrun Error 5 1 read-only FRAME Framing Error 6 1 read-only PARE Parity Error 7 1 read-only TXEMPTY Transmitter Empty 9 1 read-only TXBUFE Transmission Buffer Empty 11 1 read-only RXBUFF Receive Buffer Full 12 1 read-only COMMTX Debug Communication Channel Write Status 30 1 read-only COMMRX Debug Communication Channel Read Status 31 1 read-only RHR Receive Holding Register 0x00000018 32 read-only 0x00000000 RXCHR Received Character 0 8 read-only THR Transmit Holding Register 0x0000001C 32 write-only TXCHR Character to be Transmitted 0 8 write-only BRGR Baud Rate Generator Register 0x00000020 32 read-write 0x00000000 CD Clock Divisor 0 16 read-write DISABLED DBGU Disabled 0 MCK MCK 1 CIDR Chip ID Register 0x00000040 32 read-only VERSION Version of the Device 0 5 read-only EPROC Embedded Processor 5 3 read-only ARM946ES ARM946ES 0x1 ARM7TDMI ARM7TDMI 0x2 CM3 Cortex-M3 0x3 ARM920T ARM920T 0x4 ARM926EJS ARM926EJS 0x5 CA5 Cortex-A5 0x6 NVPSIZ Nonvolatile Program Memory Size 8 4 read-only NONE None 0x0 8K 8K bytes 0x1 16K 16K bytes 0x2 32K 32K bytes 0x3 64K 64K bytes 0x5 128K 128K bytes 0x7 256K 256K bytes 0x9 512K 512K bytes 0xA 1024K 1024K bytes 0xC 2048K 2048K bytes 0xE NVPSIZ2 12 4 read-only NONE None 0x0 8K 8K bytes 0x1 16K 16K bytes 0x2 32K 32K bytes 0x3 64K 64K bytes 0x5 128K 128K bytes 0x7 256K 256K bytes 0x9 512K 512K bytes 0xA 1024K 1024K bytes 0xC 2048K 2048K bytes 0xE SRAMSIZ Internal SRAM Size 16 4 read-only 1K 1K bytes 0x1 2K 2K bytes 0x2 6K 6K bytes 0x3 112K 112K bytes 0x4 4K 4K bytes 0x5 80K 80K bytes 0x6 160K 160K bytes 0x7 8K 8K bytes 0x8 16K 16K bytes 0x9 32K 32K bytes 0xA 64K 64K bytes 0xB 128K 128K bytes 0xC 256K 256K bytes 0xD 96K 96K bytes 0xE 512K 512K bytes 0xF ARCH Architecture Identifier 20 8 read-only AT91SAM9xx AT91SAM9xx Series 0x19 AT91SAM9XExx AT91SAM9XExx Series 0x29 AT91x34 AT91x34 Series 0x34 CAP7 CAP7 Series 0x37 CAP9 CAP9 Series 0x39 CAP11 CAP11 Series 0x3B AT91x40 AT91x40 Series 0x40 AT91x42 AT91x42 Series 0x42 AT91x55 AT91x55 Series 0x55 AT91SAM7Axx AT91SAM7Axx Series 0x60 AT91SAM7AQxx AT91SAM7AQxx Series 0x61 AT91x63 AT91x63 Series 0x63 AT91SAM7Sxx AT91SAM7Sxx Series 0x70 AT91SAM7XCxx AT91SAM7XCxx Series 0x71 AT91SAM7SExx AT91SAM7SExx Series 0x72 AT91SAM7Lxx AT91SAM7Lxx Series 0x73 AT91SAM7Xxx AT91SAM7Xxx Series 0x75 AT91SAM7SLxx AT91SAM7SLxx Series 0x76 ATSAM3UxC ATSAM3UxC Series (100-pin version) 0x80 ATSAM3UxE ATSAM3UxE Series (144-pin version) 0x81 ATSAM3AxC ATSAM3AxC Series (100-pin version) 0x83 ATSAM3XxC ATSAM3XxC Series (100-pin version) 0x84 ATSAM3XxE ATSAM3XxE Series (144-pin version) 0x85 ATSAM3XxG ATSAM3XxG Series (208/217-pin version) 0x86 ATSAM3SxA ATSAM3SxA Series (48-pin version) 0x88 ATSAM3SxB ATSAM3SxB Series (64-pin version) 0x89 ATSAM3SxC ATSAM3SxC Series (100-pin version) 0x8A AT91x92 AT91x92 Series 0x92 ATSAM3NxA ATSAM3NxA Series (48-pin version) 0x93 ATSAM3NxB ATSAM3NxB Series (64-pin version) 0x94 ATSAM3NxC ATSAM3NxC Series (100-pin version) 0x95 ATSAM3SDxA ATSAM3SDxA Series (48-pin version) 0x98 ATSAM3SDxB ATSAM3SDxB Series (64-pin version) 0x99 ATSAM3SDxC ATSAM3SDxC Series (100-pin version) 0x9A AT75Cxx AT75Cxx Series 0xF0 NVPTYP Nonvolatile Program Memory Type 28 3 read-only ROM ROM 0x0 ROMLESS ROMless or on-chip Flash 0x1 FLASH Embedded Flash Memory 0x2 ROM_FLASH ROM and Embedded Flash MemoryNVPSIZ is ROM size NVPSIZ2 is Flash size 0x3 SRAM SRAM emulating ROM 0x4 EXT Extension Flag 31 1 read-only EXID Chip ID Extension Register 0x00000044 32 read-only EXID Chip ID Extension 0 32 read-only FNR Force NTRST Register 0x00000048 32 read-write 0x00000000 FNTRST Force NTRST 0 1 read-write RPR Receive Pointer Register 0x00000100 32 read-write 0x00000000 RXPTR Receive Pointer Register 0 32 read-write RCR Receive Counter Register 0x00000104 32 read-write 0x00000000 RXCTR Receive Counter Register 0 16 read-write TPR Transmit Pointer Register 0x00000108 32 read-write 0x00000000 TXPTR Transmit Counter Register 0 32 read-write TCR Transmit Counter Register 0x0000010C 32 read-write 0x00000000 TXCTR Transmit Counter Register 0 16 read-write RNPR Receive Next Pointer Register 0x00000110 32 read-write 0x00000000 RXNPTR Receive Next Pointer 0 32 read-write RNCR Receive Next Counter Register 0x00000114 32 read-write 0x00000000 RXNCTR Receive Next Counter 0 16 read-write TNPR Transmit Next Pointer Register 0x00000118 32 read-write 0x00000000 TXNPTR Transmit Next Pointer 0 32 read-write TNCR Transmit Next Counter Register 0x0000011C 32 read-write 0x00000000 TXNCTR Transmit Counter Next 0 16 read-write PTCR Transfer Control Register 0x00000120 32 write-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 write-only RXTDIS Receiver Transfer Disable 1 1 write-only TXTEN Transmitter Transfer Enable 8 1 write-only TXTDIS Transmitter Transfer Disable 9 1 write-only PTSR Transfer Status Register 0x00000124 32 read-only 0x00000000 RXTEN Receiver Transfer Enable 0 1 read-only TXTEN Transmitter Transfer Enable 8 1 read-only PIOA 6057E Parallel Input/Output Controller A PIO PIOA_ 0xFFFFF400 0 0x200 registers PIOA 2 PER PIO Enable Register 0x00000000 32 write-only P0 PIO Enable 0 1 write-only P1 PIO Enable 1 1 write-only P2 PIO Enable 2 1 write-only P3 PIO Enable 3 1 write-only P4 PIO Enable 4 1 write-only P5 PIO Enable 5 1 write-only P6 PIO Enable 6 1 write-only P7 PIO Enable 7 1 write-only P8 PIO Enable 8 1 write-only P9 PIO Enable 9 1 write-only P10 PIO Enable 10 1 write-only P11 PIO Enable 11 1 write-only P12 PIO Enable 12 1 write-only P13 PIO Enable 13 1 write-only P14 PIO Enable 14 1 write-only P15 PIO Enable 15 1 write-only P16 PIO Enable 16 1 write-only P17 PIO Enable 17 1 write-only P18 PIO Enable 18 1 write-only P19 PIO Enable 19 1 write-only P20 PIO Enable 20 1 write-only P21 PIO Enable 21 1 write-only P22 PIO Enable 22 1 write-only P23 PIO Enable 23 1 write-only P24 PIO Enable 24 1 write-only P25 PIO Enable 25 1 write-only P26 PIO Enable 26 1 write-only P27 PIO Enable 27 1 write-only P28 PIO Enable 28 1 write-only P29 PIO Enable 29 1 write-only P30 PIO Enable 30 1 write-only P31 PIO Enable 31 1 write-only PDR PIO Disable Register 0x00000004 32 write-only P0 PIO Disable 0 1 write-only P1 PIO Disable 1 1 write-only P2 PIO Disable 2 1 write-only P3 PIO Disable 3 1 write-only P4 PIO Disable 4 1 write-only P5 PIO Disable 5 1 write-only P6 PIO Disable 6 1 write-only P7 PIO Disable 7 1 write-only P8 PIO Disable 8 1 write-only P9 PIO Disable 9 1 write-only P10 PIO Disable 10 1 write-only P11 PIO Disable 11 1 write-only P12 PIO Disable 12 1 write-only P13 PIO Disable 13 1 write-only P14 PIO Disable 14 1 write-only P15 PIO Disable 15 1 write-only P16 PIO Disable 16 1 write-only P17 PIO Disable 17 1 write-only P18 PIO Disable 18 1 write-only P19 PIO Disable 19 1 write-only P20 PIO Disable 20 1 write-only P21 PIO Disable 21 1 write-only P22 PIO Disable 22 1 write-only P23 PIO Disable 23 1 write-only P24 PIO Disable 24 1 write-only P25 PIO Disable 25 1 write-only P26 PIO Disable 26 1 write-only P27 PIO Disable 27 1 write-only P28 PIO Disable 28 1 write-only P29 PIO Disable 29 1 write-only P30 PIO Disable 30 1 write-only P31 PIO Disable 31 1 write-only PSR PIO Status Register 0x00000008 32 read-only P0 PIO Status 0 1 read-only P1 PIO Status 1 1 read-only P2 PIO Status 2 1 read-only P3 PIO Status 3 1 read-only P4 PIO Status 4 1 read-only P5 PIO Status 5 1 read-only P6 PIO Status 6 1 read-only P7 PIO Status 7 1 read-only P8 PIO Status 8 1 read-only P9 PIO Status 9 1 read-only P10 PIO Status 10 1 read-only P11 PIO Status 11 1 read-only P12 PIO Status 12 1 read-only P13 PIO Status 13 1 read-only P14 PIO Status 14 1 read-only P15 PIO Status 15 1 read-only P16 PIO Status 16 1 read-only P17 PIO Status 17 1 read-only P18 PIO Status 18 1 read-only P19 PIO Status 19 1 read-only P20 PIO Status 20 1 read-only P21 PIO Status 21 1 read-only P22 PIO Status 22 1 read-only P23 PIO Status 23 1 read-only P24 PIO Status 24 1 read-only P25 PIO Status 25 1 read-only P26 PIO Status 26 1 read-only P27 PIO Status 27 1 read-only P28 PIO Status 28 1 read-only P29 PIO Status 29 1 read-only P30 PIO Status 30 1 read-only P31 PIO Status 31 1 read-only OER Output Enable Register 0x00000010 32 write-only P0 Output Enable 0 1 write-only P1 Output Enable 1 1 write-only P2 Output Enable 2 1 write-only P3 Output Enable 3 1 write-only P4 Output Enable 4 1 write-only P5 Output Enable 5 1 write-only P6 Output Enable 6 1 write-only P7 Output Enable 7 1 write-only P8 Output Enable 8 1 write-only P9 Output Enable 9 1 write-only P10 Output Enable 10 1 write-only P11 Output Enable 11 1 write-only P12 Output Enable 12 1 write-only P13 Output Enable 13 1 write-only P14 Output Enable 14 1 write-only P15 Output Enable 15 1 write-only P16 Output Enable 16 1 write-only P17 Output Enable 17 1 write-only P18 Output Enable 18 1 write-only P19 Output Enable 19 1 write-only P20 Output Enable 20 1 write-only P21 Output Enable 21 1 write-only P22 Output Enable 22 1 write-only P23 Output Enable 23 1 write-only P24 Output Enable 24 1 write-only P25 Output Enable 25 1 write-only P26 Output Enable 26 1 write-only P27 Output Enable 27 1 write-only P28 Output Enable 28 1 write-only P29 Output Enable 29 1 write-only P30 Output Enable 30 1 write-only P31 Output Enable 31 1 write-only ODR Output Disable Register 0x00000014 32 write-only P0 Output Disable 0 1 write-only P1 Output Disable 1 1 write-only P2 Output Disable 2 1 write-only P3 Output Disable 3 1 write-only P4 Output Disable 4 1 write-only P5 Output Disable 5 1 write-only P6 Output Disable 6 1 write-only P7 Output Disable 7 1 write-only P8 Output Disable 8 1 write-only P9 Output Disable 9 1 write-only P10 Output Disable 10 1 write-only P11 Output Disable 11 1 write-only P12 Output Disable 12 1 write-only P13 Output Disable 13 1 write-only P14 Output Disable 14 1 write-only P15 Output Disable 15 1 write-only P16 Output Disable 16 1 write-only P17 Output Disable 17 1 write-only P18 Output Disable 18 1 write-only P19 Output Disable 19 1 write-only P20 Output Disable 20 1 write-only P21 Output Disable 21 1 write-only P22 Output Disable 22 1 write-only P23 Output Disable 23 1 write-only P24 Output Disable 24 1 write-only P25 Output Disable 25 1 write-only P26 Output Disable 26 1 write-only P27 Output Disable 27 1 write-only P28 Output Disable 28 1 write-only P29 Output Disable 29 1 write-only P30 Output Disable 30 1 write-only P31 Output Disable 31 1 write-only OSR Output Status Register 0x00000018 32 read-only 0x00000000 P0 Output Status 0 1 read-only P1 Output Status 1 1 read-only P2 Output Status 2 1 read-only P3 Output Status 3 1 read-only P4 Output Status 4 1 read-only P5 Output Status 5 1 read-only P6 Output Status 6 1 read-only P7 Output Status 7 1 read-only P8 Output Status 8 1 read-only P9 Output Status 9 1 read-only P10 Output Status 10 1 read-only P11 Output Status 11 1 read-only P12 Output Status 12 1 read-only P13 Output Status 13 1 read-only P14 Output Status 14 1 read-only P15 Output Status 15 1 read-only P16 Output Status 16 1 read-only P17 Output Status 17 1 read-only P18 Output Status 18 1 read-only P19 Output Status 19 1 read-only P20 Output Status 20 1 read-only P21 Output Status 21 1 read-only P22 Output Status 22 1 read-only P23 Output Status 23 1 read-only P24 Output Status 24 1 read-only P25 Output Status 25 1 read-only P26 Output Status 26 1 read-only P27 Output Status 27 1 read-only P28 Output Status 28 1 read-only P29 Output Status 29 1 read-only P30 Output Status 30 1 read-only P31 Output Status 31 1 read-only IFER Glitch Input Filter Enable Register 0x00000020 32 write-only P0 Input Filter Enable 0 1 write-only P1 Input Filter Enable 1 1 write-only P2 Input Filter Enable 2 1 write-only P3 Input Filter Enable 3 1 write-only P4 Input Filter Enable 4 1 write-only P5 Input Filter Enable 5 1 write-only P6 Input Filter Enable 6 1 write-only P7 Input Filter Enable 7 1 write-only P8 Input Filter Enable 8 1 write-only P9 Input Filter Enable 9 1 write-only P10 Input Filter Enable 10 1 write-only P11 Input Filter Enable 11 1 write-only P12 Input Filter Enable 12 1 write-only P13 Input Filter Enable 13 1 write-only P14 Input Filter Enable 14 1 write-only P15 Input Filter Enable 15 1 write-only P16 Input Filter Enable 16 1 write-only P17 Input Filter Enable 17 1 write-only P18 Input Filter Enable 18 1 write-only P19 Input Filter Enable 19 1 write-only P20 Input Filter Enable 20 1 write-only P21 Input Filter Enable 21 1 write-only P22 Input Filter Enable 22 1 write-only P23 Input Filter Enable 23 1 write-only P24 Input Filter Enable 24 1 write-only P25 Input Filter Enable 25 1 write-only P26 Input Filter Enable 26 1 write-only P27 Input Filter Enable 27 1 write-only P28 Input Filter Enable 28 1 write-only P29 Input Filter Enable 29 1 write-only P30 Input Filter Enable 30 1 write-only P31 Input Filter Enable 31 1 write-only IFDR Glitch Input Filter Disable Register 0x00000024 32 write-only P0 Input Filter Disable 0 1 write-only P1 Input Filter Disable 1 1 write-only P2 Input Filter Disable 2 1 write-only P3 Input Filter Disable 3 1 write-only P4 Input Filter Disable 4 1 write-only P5 Input Filter Disable 5 1 write-only P6 Input Filter Disable 6 1 write-only P7 Input Filter Disable 7 1 write-only P8 Input Filter Disable 8 1 write-only P9 Input Filter Disable 9 1 write-only P10 Input Filter Disable 10 1 write-only P11 Input Filter Disable 11 1 write-only P12 Input Filter Disable 12 1 write-only P13 Input Filter Disable 13 1 write-only P14 Input Filter Disable 14 1 write-only P15 Input Filter Disable 15 1 write-only P16 Input Filter Disable 16 1 write-only P17 Input Filter Disable 17 1 write-only P18 Input Filter Disable 18 1 write-only P19 Input Filter Disable 19 1 write-only P20 Input Filter Disable 20 1 write-only P21 Input Filter Disable 21 1 write-only P22 Input Filter Disable 22 1 write-only P23 Input Filter Disable 23 1 write-only P24 Input Filter Disable 24 1 write-only P25 Input Filter Disable 25 1 write-only P26 Input Filter Disable 26 1 write-only P27 Input Filter Disable 27 1 write-only P28 Input Filter Disable 28 1 write-only P29 Input Filter Disable 29 1 write-only P30 Input Filter Disable 30 1 write-only P31 Input Filter Disable 31 1 write-only IFSR Glitch Input Filter Status Register 0x00000028 32 read-only 0x00000000 P0 Input Filer Status 0 1 read-only P1 Input Filer Status 1 1 read-only P2 Input Filer Status 2 1 read-only P3 Input Filer Status 3 1 read-only P4 Input Filer Status 4 1 read-only P5 Input Filer Status 5 1 read-only P6 Input Filer Status 6 1 read-only P7 Input Filer Status 7 1 read-only P8 Input Filer Status 8 1 read-only P9 Input Filer Status 9 1 read-only P10 Input Filer Status 10 1 read-only P11 Input Filer Status 11 1 read-only P12 Input Filer Status 12 1 read-only P13 Input Filer Status 13 1 read-only P14 Input Filer Status 14 1 read-only P15 Input Filer Status 15 1 read-only P16 Input Filer Status 16 1 read-only P17 Input Filer Status 17 1 read-only P18 Input Filer Status 18 1 read-only P19 Input Filer Status 19 1 read-only P20 Input Filer Status 20 1 read-only P21 Input Filer Status 21 1 read-only P22 Input Filer Status 22 1 read-only P23 Input Filer Status 23 1 read-only P24 Input Filer Status 24 1 read-only P25 Input Filer Status 25 1 read-only P26 Input Filer Status 26 1 read-only P27 Input Filer Status 27 1 read-only P28 Input Filer Status 28 1 read-only P29 Input Filer Status 29 1 read-only P30 Input Filer Status 30 1 read-only P31 Input Filer Status 31 1 read-only SODR Set Output Data Register 0x00000030 32 write-only P0 Set Output Data 0 1 write-only P1 Set Output Data 1 1 write-only P2 Set Output Data 2 1 write-only P3 Set Output Data 3 1 write-only P4 Set Output Data 4 1 write-only P5 Set Output Data 5 1 write-only P6 Set Output Data 6 1 write-only P7 Set Output Data 7 1 write-only P8 Set Output Data 8 1 write-only P9 Set Output Data 9 1 write-only P10 Set Output Data 10 1 write-only P11 Set Output Data 11 1 write-only P12 Set Output Data 12 1 write-only P13 Set Output Data 13 1 write-only P14 Set Output Data 14 1 write-only P15 Set Output Data 15 1 write-only P16 Set Output Data 16 1 write-only P17 Set Output Data 17 1 write-only P18 Set Output Data 18 1 write-only P19 Set Output Data 19 1 write-only P20 Set Output Data 20 1 write-only P21 Set Output Data 21 1 write-only P22 Set Output Data 22 1 write-only P23 Set Output Data 23 1 write-only P24 Set Output Data 24 1 write-only P25 Set Output Data 25 1 write-only P26 Set Output Data 26 1 write-only P27 Set Output Data 27 1 write-only P28 Set Output Data 28 1 write-only P29 Set Output Data 29 1 write-only P30 Set Output Data 30 1 write-only P31 Set Output Data 31 1 write-only CODR Clear Output Data Register 0x00000034 32 write-only P0 Set Output Data 0 1 write-only P1 Set Output Data 1 1 write-only P2 Set Output Data 2 1 write-only P3 Set Output Data 3 1 write-only P4 Set Output Data 4 1 write-only P5 Set Output Data 5 1 write-only P6 Set Output Data 6 1 write-only P7 Set Output Data 7 1 write-only P8 Set Output Data 8 1 write-only P9 Set Output Data 9 1 write-only P10 Set Output Data 10 1 write-only P11 Set Output Data 11 1 write-only P12 Set Output Data 12 1 write-only P13 Set Output Data 13 1 write-only P14 Set Output Data 14 1 write-only P15 Set Output Data 15 1 write-only P16 Set Output Data 16 1 write-only P17 Set Output Data 17 1 write-only P18 Set Output Data 18 1 write-only P19 Set Output Data 19 1 write-only P20 Set Output Data 20 1 write-only P21 Set Output Data 21 1 write-only P22 Set Output Data 22 1 write-only P23 Set Output Data 23 1 write-only P24 Set Output Data 24 1 write-only P25 Set Output Data 25 1 write-only P26 Set Output Data 26 1 write-only P27 Set Output Data 27 1 write-only P28 Set Output Data 28 1 write-only P29 Set Output Data 29 1 write-only P30 Set Output Data 30 1 write-only P31 Set Output Data 31 1 write-only ODSR Output Data Status Register 0x00000038 32 read-write P0 Output Data Status 0 1 read-write P1 Output Data Status 1 1 read-write P2 Output Data Status 2 1 read-write P3 Output Data Status 3 1 read-write P4 Output Data Status 4 1 read-write P5 Output Data Status 5 1 read-write P6 Output Data Status 6 1 read-write P7 Output Data Status 7 1 read-write P8 Output Data Status 8 1 read-write P9 Output Data Status 9 1 read-write P10 Output Data Status 10 1 read-write P11 Output Data Status 11 1 read-write P12 Output Data Status 12 1 read-write P13 Output Data Status 13 1 read-write P14 Output Data Status 14 1 read-write P15 Output Data Status 15 1 read-write P16 Output Data Status 16 1 read-write P17 Output Data Status 17 1 read-write P18 Output Data Status 18 1 read-write P19 Output Data Status 19 1 read-write P20 Output Data Status 20 1 read-write P21 Output Data Status 21 1 read-write P22 Output Data Status 22 1 read-write P23 Output Data Status 23 1 read-write P24 Output Data Status 24 1 read-write P25 Output Data Status 25 1 read-write P26 Output Data Status 26 1 read-write P27 Output Data Status 27 1 read-write P28 Output Data Status 28 1 read-write P29 Output Data Status 29 1 read-write P30 Output Data Status 30 1 read-write P31 Output Data Status 31 1 read-write PDSR Pin Data Status Register 0x0000003C 32 read-only P0 Output Data Status 0 1 read-only P1 Output Data Status 1 1 read-only P2 Output Data Status 2 1 read-only P3 Output Data Status 3 1 read-only P4 Output Data Status 4 1 read-only P5 Output Data Status 5 1 read-only P6 Output Data Status 6 1 read-only P7 Output Data Status 7 1 read-only P8 Output Data Status 8 1 read-only P9 Output Data Status 9 1 read-only P10 Output Data Status 10 1 read-only P11 Output Data Status 11 1 read-only P12 Output Data Status 12 1 read-only P13 Output Data Status 13 1 read-only P14 Output Data Status 14 1 read-only P15 Output Data Status 15 1 read-only P16 Output Data Status 16 1 read-only P17 Output Data Status 17 1 read-only P18 Output Data Status 18 1 read-only P19 Output Data Status 19 1 read-only P20 Output Data Status 20 1 read-only P21 Output Data Status 21 1 read-only P22 Output Data Status 22 1 read-only P23 Output Data Status 23 1 read-only P24 Output Data Status 24 1 read-only P25 Output Data Status 25 1 read-only P26 Output Data Status 26 1 read-only P27 Output Data Status 27 1 read-only P28 Output Data Status 28 1 read-only P29 Output Data Status 29 1 read-only P30 Output Data Status 30 1 read-only P31 Output Data Status 31 1 read-only IER Interrupt Enable Register 0x00000040 32 write-only P0 Input Change Interrupt Enable 0 1 write-only P1 Input Change Interrupt Enable 1 1 write-only P2 Input Change Interrupt Enable 2 1 write-only P3 Input Change Interrupt Enable 3 1 write-only P4 Input Change Interrupt Enable 4 1 write-only P5 Input Change Interrupt Enable 5 1 write-only P6 Input Change Interrupt Enable 6 1 write-only P7 Input Change Interrupt Enable 7 1 write-only P8 Input Change Interrupt Enable 8 1 write-only P9 Input Change Interrupt Enable 9 1 write-only P10 Input Change Interrupt Enable 10 1 write-only P11 Input Change Interrupt Enable 11 1 write-only P12 Input Change Interrupt Enable 12 1 write-only P13 Input Change Interrupt Enable 13 1 write-only P14 Input Change Interrupt Enable 14 1 write-only P15 Input Change Interrupt Enable 15 1 write-only P16 Input Change Interrupt Enable 16 1 write-only P17 Input Change Interrupt Enable 17 1 write-only P18 Input Change Interrupt Enable 18 1 write-only P19 Input Change Interrupt Enable 19 1 write-only P20 Input Change Interrupt Enable 20 1 write-only P21 Input Change Interrupt Enable 21 1 write-only P22 Input Change Interrupt Enable 22 1 write-only P23 Input Change Interrupt Enable 23 1 write-only P24 Input Change Interrupt Enable 24 1 write-only P25 Input Change Interrupt Enable 25 1 write-only P26 Input Change Interrupt Enable 26 1 write-only P27 Input Change Interrupt Enable 27 1 write-only P28 Input Change Interrupt Enable 28 1 write-only P29 Input Change Interrupt Enable 29 1 write-only P30 Input Change Interrupt Enable 30 1 write-only P31 Input Change Interrupt Enable 31 1 write-only IDR Interrupt Disable Register 0x00000044 32 write-only P0 Input Change Interrupt Disable 0 1 write-only P1 Input Change Interrupt Disable 1 1 write-only P2 Input Change Interrupt Disable 2 1 write-only P3 Input Change Interrupt Disable 3 1 write-only P4 Input Change Interrupt Disable 4 1 write-only P5 Input Change Interrupt Disable 5 1 write-only P6 Input Change Interrupt Disable 6 1 write-only P7 Input Change Interrupt Disable 7 1 write-only P8 Input Change Interrupt Disable 8 1 write-only P9 Input Change Interrupt Disable 9 1 write-only P10 Input Change Interrupt Disable 10 1 write-only P11 Input Change Interrupt Disable 11 1 write-only P12 Input Change Interrupt Disable 12 1 write-only P13 Input Change Interrupt Disable 13 1 write-only P14 Input Change Interrupt Disable 14 1 write-only P15 Input Change Interrupt Disable 15 1 write-only P16 Input Change Interrupt Disable 16 1 write-only P17 Input Change Interrupt Disable 17 1 write-only P18 Input Change Interrupt Disable 18 1 write-only P19 Input Change Interrupt Disable 19 1 write-only P20 Input Change Interrupt Disable 20 1 write-only P21 Input Change Interrupt Disable 21 1 write-only P22 Input Change Interrupt Disable 22 1 write-only P23 Input Change Interrupt Disable 23 1 write-only P24 Input Change Interrupt Disable 24 1 write-only P25 Input Change Interrupt Disable 25 1 write-only P26 Input Change Interrupt Disable 26 1 write-only P27 Input Change Interrupt Disable 27 1 write-only P28 Input Change Interrupt Disable 28 1 write-only P29 Input Change Interrupt Disable 29 1 write-only P30 Input Change Interrupt Disable 30 1 write-only P31 Input Change Interrupt Disable 31 1 write-only IMR Interrupt Mask Register 0x00000048 32 read-only 0x00000000 P0 Input Change Interrupt Mask 0 1 read-only P1 Input Change Interrupt Mask 1 1 read-only P2 Input Change Interrupt Mask 2 1 read-only P3 Input Change Interrupt Mask 3 1 read-only P4 Input Change Interrupt Mask 4 1 read-only P5 Input Change Interrupt Mask 5 1 read-only P6 Input Change Interrupt Mask 6 1 read-only P7 Input Change Interrupt Mask 7 1 read-only P8 Input Change Interrupt Mask 8 1 read-only P9 Input Change Interrupt Mask 9 1 read-only P10 Input Change Interrupt Mask 10 1 read-only P11 Input Change Interrupt Mask 11 1 read-only P12 Input Change Interrupt Mask 12 1 read-only P13 Input Change Interrupt Mask 13 1 read-only P14 Input Change Interrupt Mask 14 1 read-only P15 Input Change Interrupt Mask 15 1 read-only P16 Input Change Interrupt Mask 16 1 read-only P17 Input Change Interrupt Mask 17 1 read-only P18 Input Change Interrupt Mask 18 1 read-only P19 Input Change Interrupt Mask 19 1 read-only P20 Input Change Interrupt Mask 20 1 read-only P21 Input Change Interrupt Mask 21 1 read-only P22 Input Change Interrupt Mask 22 1 read-only P23 Input Change Interrupt Mask 23 1 read-only P24 Input Change Interrupt Mask 24 1 read-only P25 Input Change Interrupt Mask 25 1 read-only P26 Input Change Interrupt Mask 26 1 read-only P27 Input Change Interrupt Mask 27 1 read-only P28 Input Change Interrupt Mask 28 1 read-only P29 Input Change Interrupt Mask 29 1 read-only P30 Input Change Interrupt Mask 30 1 read-only P31 Input Change Interrupt Mask 31 1 read-only ISR Interrupt Status Register 0x0000004C 32 read-only 0x00000000 P0 Input Change Interrupt Status 0 1 read-only P1 Input Change Interrupt Status 1 1 read-only P2 Input Change Interrupt Status 2 1 read-only P3 Input Change Interrupt Status 3 1 read-only P4 Input Change Interrupt Status 4 1 read-only P5 Input Change Interrupt Status 5 1 read-only P6 Input Change Interrupt Status 6 1 read-only P7 Input Change Interrupt Status 7 1 read-only P8 Input Change Interrupt Status 8 1 read-only P9 Input Change Interrupt Status 9 1 read-only P10 Input Change Interrupt Status 10 1 read-only P11 Input Change Interrupt Status 11 1 read-only P12 Input Change Interrupt Status 12 1 read-only P13 Input Change Interrupt Status 13 1 read-only P14 Input Change Interrupt Status 14 1 read-only P15 Input Change Interrupt Status 15 1 read-only P16 Input Change Interrupt Status 16 1 read-only P17 Input Change Interrupt Status 17 1 read-only P18 Input Change Interrupt Status 18 1 read-only P19 Input Change Interrupt Status 19 1 read-only P20 Input Change Interrupt Status 20 1 read-only P21 Input Change Interrupt Status 21 1 read-only P22 Input Change Interrupt Status 22 1 read-only P23 Input Change Interrupt Status 23 1 read-only P24 Input Change Interrupt Status 24 1 read-only P25 Input Change Interrupt Status 25 1 read-only P26 Input Change Interrupt Status 26 1 read-only P27 Input Change Interrupt Status 27 1 read-only P28 Input Change Interrupt Status 28 1 read-only P29 Input Change Interrupt Status 29 1 read-only P30 Input Change Interrupt Status 30 1 read-only P31 Input Change Interrupt Status 31 1 read-only MDER Multi-driver Enable Register 0x00000050 32 write-only P0 Multi Drive Enable. 0 1 write-only P1 Multi Drive Enable. 1 1 write-only P2 Multi Drive Enable. 2 1 write-only P3 Multi Drive Enable. 3 1 write-only P4 Multi Drive Enable. 4 1 write-only P5 Multi Drive Enable. 5 1 write-only P6 Multi Drive Enable. 6 1 write-only P7 Multi Drive Enable. 7 1 write-only P8 Multi Drive Enable. 8 1 write-only P9 Multi Drive Enable. 9 1 write-only P10 Multi Drive Enable. 10 1 write-only P11 Multi Drive Enable. 11 1 write-only P12 Multi Drive Enable. 12 1 write-only P13 Multi Drive Enable. 13 1 write-only P14 Multi Drive Enable. 14 1 write-only P15 Multi Drive Enable. 15 1 write-only P16 Multi Drive Enable. 16 1 write-only P17 Multi Drive Enable. 17 1 write-only P18 Multi Drive Enable. 18 1 write-only P19 Multi Drive Enable. 19 1 write-only P20 Multi Drive Enable. 20 1 write-only P21 Multi Drive Enable. 21 1 write-only P22 Multi Drive Enable. 22 1 write-only P23 Multi Drive Enable. 23 1 write-only P24 Multi Drive Enable. 24 1 write-only P25 Multi Drive Enable. 25 1 write-only P26 Multi Drive Enable. 26 1 write-only P27 Multi Drive Enable. 27 1 write-only P28 Multi Drive Enable. 28 1 write-only P29 Multi Drive Enable. 29 1 write-only P30 Multi Drive Enable. 30 1 write-only P31 Multi Drive Enable. 31 1 write-only MDDR Multi-driver Disable Register 0x00000054 32 write-only P0 Multi Drive Disable. 0 1 write-only P1 Multi Drive Disable. 1 1 write-only P2 Multi Drive Disable. 2 1 write-only P3 Multi Drive Disable. 3 1 write-only P4 Multi Drive Disable. 4 1 write-only P5 Multi Drive Disable. 5 1 write-only P6 Multi Drive Disable. 6 1 write-only P7 Multi Drive Disable. 7 1 write-only P8 Multi Drive Disable. 8 1 write-only P9 Multi Drive Disable. 9 1 write-only P10 Multi Drive Disable. 10 1 write-only P11 Multi Drive Disable. 11 1 write-only P12 Multi Drive Disable. 12 1 write-only P13 Multi Drive Disable. 13 1 write-only P14 Multi Drive Disable. 14 1 write-only P15 Multi Drive Disable. 15 1 write-only P16 Multi Drive Disable. 16 1 write-only P17 Multi Drive Disable. 17 1 write-only P18 Multi Drive Disable. 18 1 write-only P19 Multi Drive Disable. 19 1 write-only P20 Multi Drive Disable. 20 1 write-only P21 Multi Drive Disable. 21 1 write-only P22 Multi Drive Disable. 22 1 write-only P23 Multi Drive Disable. 23 1 write-only P24 Multi Drive Disable. 24 1 write-only P25 Multi Drive Disable. 25 1 write-only P26 Multi Drive Disable. 26 1 write-only P27 Multi Drive Disable. 27 1 write-only P28 Multi Drive Disable. 28 1 write-only P29 Multi Drive Disable. 29 1 write-only P30 Multi Drive Disable. 30 1 write-only P31 Multi Drive Disable. 31 1 write-only MDSR Multi-driver Status Register 0x00000058 32 read-only 0x00000000 P0 Multi Drive Status. 0 1 read-only P1 Multi Drive Status. 1 1 read-only P2 Multi Drive Status. 2 1 read-only P3 Multi Drive Status. 3 1 read-only P4 Multi Drive Status. 4 1 read-only P5 Multi Drive Status. 5 1 read-only P6 Multi Drive Status. 6 1 read-only P7 Multi Drive Status. 7 1 read-only P8 Multi Drive Status. 8 1 read-only P9 Multi Drive Status. 9 1 read-only P10 Multi Drive Status. 10 1 read-only P11 Multi Drive Status. 11 1 read-only P12 Multi Drive Status. 12 1 read-only P13 Multi Drive Status. 13 1 read-only P14 Multi Drive Status. 14 1 read-only P15 Multi Drive Status. 15 1 read-only P16 Multi Drive Status. 16 1 read-only P17 Multi Drive Status. 17 1 read-only P18 Multi Drive Status. 18 1 read-only P19 Multi Drive Status. 19 1 read-only P20 Multi Drive Status. 20 1 read-only P21 Multi Drive Status. 21 1 read-only P22 Multi Drive Status. 22 1 read-only P23 Multi Drive Status. 23 1 read-only P24 Multi Drive Status. 24 1 read-only P25 Multi Drive Status. 25 1 read-only P26 Multi Drive Status. 26 1 read-only P27 Multi Drive Status. 27 1 read-only P28 Multi Drive Status. 28 1 read-only P29 Multi Drive Status. 29 1 read-only P30 Multi Drive Status. 30 1 read-only P31 Multi Drive Status. 31 1 read-only PUDR Pull-up Disable Register 0x00000060 32 write-only P0 Pull Up Disable. 0 1 write-only P1 Pull Up Disable. 1 1 write-only P2 Pull Up Disable. 2 1 write-only P3 Pull Up Disable. 3 1 write-only P4 Pull Up Disable. 4 1 write-only P5 Pull Up Disable. 5 1 write-only P6 Pull Up Disable. 6 1 write-only P7 Pull Up Disable. 7 1 write-only P8 Pull Up Disable. 8 1 write-only P9 Pull Up Disable. 9 1 write-only P10 Pull Up Disable. 10 1 write-only P11 Pull Up Disable. 11 1 write-only P12 Pull Up Disable. 12 1 write-only P13 Pull Up Disable. 13 1 write-only P14 Pull Up Disable. 14 1 write-only P15 Pull Up Disable. 15 1 write-only P16 Pull Up Disable. 16 1 write-only P17 Pull Up Disable. 17 1 write-only P18 Pull Up Disable. 18 1 write-only P19 Pull Up Disable. 19 1 write-only P20 Pull Up Disable. 20 1 write-only P21 Pull Up Disable. 21 1 write-only P22 Pull Up Disable. 22 1 write-only P23 Pull Up Disable. 23 1 write-only P24 Pull Up Disable. 24 1 write-only P25 Pull Up Disable. 25 1 write-only P26 Pull Up Disable. 26 1 write-only P27 Pull Up Disable. 27 1 write-only P28 Pull Up Disable. 28 1 write-only P29 Pull Up Disable. 29 1 write-only P30 Pull Up Disable. 30 1 write-only P31 Pull Up Disable. 31 1 write-only PUER Pull-up Enable Register 0x00000064 32 write-only P0 Pull Up Enable. 0 1 write-only P1 Pull Up Enable. 1 1 write-only P2 Pull Up Enable. 2 1 write-only P3 Pull Up Enable. 3 1 write-only P4 Pull Up Enable. 4 1 write-only P5 Pull Up Enable. 5 1 write-only P6 Pull Up Enable. 6 1 write-only P7 Pull Up Enable. 7 1 write-only P8 Pull Up Enable. 8 1 write-only P9 Pull Up Enable. 9 1 write-only P10 Pull Up Enable. 10 1 write-only P11 Pull Up Enable. 11 1 write-only P12 Pull Up Enable. 12 1 write-only P13 Pull Up Enable. 13 1 write-only P14 Pull Up Enable. 14 1 write-only P15 Pull Up Enable. 15 1 write-only P16 Pull Up Enable. 16 1 write-only P17 Pull Up Enable. 17 1 write-only P18 Pull Up Enable. 18 1 write-only P19 Pull Up Enable. 19 1 write-only P20 Pull Up Enable. 20 1 write-only P21 Pull Up Enable. 21 1 write-only P22 Pull Up Enable. 22 1 write-only P23 Pull Up Enable. 23 1 write-only P24 Pull Up Enable. 24 1 write-only P25 Pull Up Enable. 25 1 write-only P26 Pull Up Enable. 26 1 write-only P27 Pull Up Enable. 27 1 write-only P28 Pull Up Enable. 28 1 write-only P29 Pull Up Enable. 29 1 write-only P30 Pull Up Enable. 30 1 write-only P31 Pull Up Enable. 31 1 write-only PUSR Pad Pull-up Status Register 0x00000068 32 read-only 0x00000000 P0 Pull Up Status. 0 1 read-only P1 Pull Up Status. 1 1 read-only P2 Pull Up Status. 2 1 read-only P3 Pull Up Status. 3 1 read-only P4 Pull Up Status. 4 1 read-only P5 Pull Up Status. 5 1 read-only P6 Pull Up Status. 6 1 read-only P7 Pull Up Status. 7 1 read-only P8 Pull Up Status. 8 1 read-only P9 Pull Up Status. 9 1 read-only P10 Pull Up Status. 10 1 read-only P11 Pull Up Status. 11 1 read-only P12 Pull Up Status. 12 1 read-only P13 Pull Up Status. 13 1 read-only P14 Pull Up Status. 14 1 read-only P15 Pull Up Status. 15 1 read-only P16 Pull Up Status. 16 1 read-only P17 Pull Up Status. 17 1 read-only P18 Pull Up Status. 18 1 read-only P19 Pull Up Status. 19 1 read-only P20 Pull Up Status. 20 1 read-only P21 Pull Up Status. 21 1 read-only P22 Pull Up Status. 22 1 read-only P23 Pull Up Status. 23 1 read-only P24 Pull Up Status. 24 1 read-only P25 Pull Up Status. 25 1 read-only P26 Pull Up Status. 26 1 read-only P27 Pull Up Status. 27 1 read-only P28 Pull Up Status. 28 1 read-only P29 Pull Up Status. 29 1 read-only P30 Pull Up Status. 30 1 read-only P31 Pull Up Status. 31 1 read-only ASR Peripheral A Select Register 0x00000070 32 write-only P0 Peripheral A Select. 0 1 write-only P1 Peripheral A Select. 1 1 write-only P2 Peripheral A Select. 2 1 write-only P3 Peripheral A Select. 3 1 write-only P4 Peripheral A Select. 4 1 write-only P5 Peripheral A Select. 5 1 write-only P6 Peripheral A Select. 6 1 write-only P7 Peripheral A Select. 7 1 write-only P8 Peripheral A Select. 8 1 write-only P9 Peripheral A Select. 9 1 write-only P10 Peripheral A Select. 10 1 write-only P11 Peripheral A Select. 11 1 write-only P12 Peripheral A Select. 12 1 write-only P13 Peripheral A Select. 13 1 write-only P14 Peripheral A Select. 14 1 write-only P15 Peripheral A Select. 15 1 write-only P16 Peripheral A Select. 16 1 write-only P17 Peripheral A Select. 17 1 write-only P18 Peripheral A Select. 18 1 write-only P19 Peripheral A Select. 19 1 write-only P20 Peripheral A Select. 20 1 write-only P21 Peripheral A Select. 21 1 write-only P22 Peripheral A Select. 22 1 write-only P23 Peripheral A Select. 23 1 write-only P24 Peripheral A Select. 24 1 write-only P25 Peripheral A Select. 25 1 write-only P26 Peripheral A Select. 26 1 write-only P27 Peripheral A Select. 27 1 write-only P28 Peripheral A Select. 28 1 write-only P29 Peripheral A Select. 29 1 write-only P30 Peripheral A Select. 30 1 write-only P31 Peripheral A Select. 31 1 write-only BSR Peripheral B Select Register 0x00000074 32 write-only P0 Peripheral B Select. 0 1 write-only P1 Peripheral B Select. 1 1 write-only P2 Peripheral B Select. 2 1 write-only P3 Peripheral B Select. 3 1 write-only P4 Peripheral B Select. 4 1 write-only P5 Peripheral B Select. 5 1 write-only P6 Peripheral B Select. 6 1 write-only P7 Peripheral B Select. 7 1 write-only P8 Peripheral B Select. 8 1 write-only P9 Peripheral B Select. 9 1 write-only P10 Peripheral B Select. 10 1 write-only P11 Peripheral B Select. 11 1 write-only P12 Peripheral B Select. 12 1 write-only P13 Peripheral B Select. 13 1 write-only P14 Peripheral B Select. 14 1 write-only P15 Peripheral B Select. 15 1 write-only P16 Peripheral B Select. 16 1 write-only P17 Peripheral B Select. 17 1 write-only P18 Peripheral B Select. 18 1 write-only P19 Peripheral B Select. 19 1 write-only P20 Peripheral B Select. 20 1 write-only P21 Peripheral B Select. 21 1 write-only P22 Peripheral B Select. 22 1 write-only P23 Peripheral B Select. 23 1 write-only P24 Peripheral B Select. 24 1 write-only P25 Peripheral B Select. 25 1 write-only P26 Peripheral B Select. 26 1 write-only P27 Peripheral B Select. 27 1 write-only P28 Peripheral B Select. 28 1 write-only P29 Peripheral B Select. 29 1 write-only P30 Peripheral B Select. 30 1 write-only P31 Peripheral B Select. 31 1 write-only ABSR AB Status Register 0x00000078 32 read-only 0x00000000 P0 Peripheral A B Status. 0 1 read-only P1 Peripheral A B Status. 1 1 read-only P2 Peripheral A B Status. 2 1 read-only P3 Peripheral A B Status. 3 1 read-only P4 Peripheral A B Status. 4 1 read-only P5 Peripheral A B Status. 5 1 read-only P6 Peripheral A B Status. 6 1 read-only P7 Peripheral A B Status. 7 1 read-only P8 Peripheral A B Status. 8 1 read-only P9 Peripheral A B Status. 9 1 read-only P10 Peripheral A B Status. 10 1 read-only P11 Peripheral A B Status. 11 1 read-only P12 Peripheral A B Status. 12 1 read-only P13 Peripheral A B Status. 13 1 read-only P14 Peripheral A B Status. 14 1 read-only P15 Peripheral A B Status. 15 1 read-only P16 Peripheral A B Status. 16 1 read-only P17 Peripheral A B Status. 17 1 read-only P18 Peripheral A B Status. 18 1 read-only P19 Peripheral A B Status. 19 1 read-only P20 Peripheral A B Status. 20 1 read-only P21 Peripheral A B Status. 21 1 read-only P22 Peripheral A B Status. 22 1 read-only P23 Peripheral A B Status. 23 1 read-only P24 Peripheral A B Status. 24 1 read-only P25 Peripheral A B Status. 25 1 read-only P26 Peripheral A B Status. 26 1 read-only P27 Peripheral A B Status. 27 1 read-only P28 Peripheral A B Status. 28 1 read-only P29 Peripheral A B Status. 29 1 read-only P30 Peripheral A B Status. 30 1 read-only P31 Peripheral A B Status. 31 1 read-only OWER Output Write Enable 0x000000A0 32 write-only P0 Output Write Enable. 0 1 write-only P1 Output Write Enable. 1 1 write-only P2 Output Write Enable. 2 1 write-only P3 Output Write Enable. 3 1 write-only P4 Output Write Enable. 4 1 write-only P5 Output Write Enable. 5 1 write-only P6 Output Write Enable. 6 1 write-only P7 Output Write Enable. 7 1 write-only P8 Output Write Enable. 8 1 write-only P9 Output Write Enable. 9 1 write-only P10 Output Write Enable. 10 1 write-only P11 Output Write Enable. 11 1 write-only P12 Output Write Enable. 12 1 write-only P13 Output Write Enable. 13 1 write-only P14 Output Write Enable. 14 1 write-only P15 Output Write Enable. 15 1 write-only P16 Output Write Enable. 16 1 write-only P17 Output Write Enable. 17 1 write-only P18 Output Write Enable. 18 1 write-only P19 Output Write Enable. 19 1 write-only P20 Output Write Enable. 20 1 write-only P21 Output Write Enable. 21 1 write-only P22 Output Write Enable. 22 1 write-only P23 Output Write Enable. 23 1 write-only P24 Output Write Enable. 24 1 write-only P25 Output Write Enable. 25 1 write-only P26 Output Write Enable. 26 1 write-only P27 Output Write Enable. 27 1 write-only P28 Output Write Enable. 28 1 write-only P29 Output Write Enable. 29 1 write-only P30 Output Write Enable. 30 1 write-only P31 Output Write Enable. 31 1 write-only OWDR Output Write Disable 0x000000A4 32 write-only P0 Output Write Disable. 0 1 write-only P1 Output Write Disable. 1 1 write-only P2 Output Write Disable. 2 1 write-only P3 Output Write Disable. 3 1 write-only P4 Output Write Disable. 4 1 write-only P5 Output Write Disable. 5 1 write-only P6 Output Write Disable. 6 1 write-only P7 Output Write Disable. 7 1 write-only P8 Output Write Disable. 8 1 write-only P9 Output Write Disable. 9 1 write-only P10 Output Write Disable. 10 1 write-only P11 Output Write Disable. 11 1 write-only P12 Output Write Disable. 12 1 write-only P13 Output Write Disable. 13 1 write-only P14 Output Write Disable. 14 1 write-only P15 Output Write Disable. 15 1 write-only P16 Output Write Disable. 16 1 write-only P17 Output Write Disable. 17 1 write-only P18 Output Write Disable. 18 1 write-only P19 Output Write Disable. 19 1 write-only P20 Output Write Disable. 20 1 write-only P21 Output Write Disable. 21 1 write-only P22 Output Write Disable. 22 1 write-only P23 Output Write Disable. 23 1 write-only P24 Output Write Disable. 24 1 write-only P25 Output Write Disable. 25 1 write-only P26 Output Write Disable. 26 1 write-only P27 Output Write Disable. 27 1 write-only P28 Output Write Disable. 28 1 write-only P29 Output Write Disable. 29 1 write-only P30 Output Write Disable. 30 1 write-only P31 Output Write Disable. 31 1 write-only OWSR Output Write Status Register 0x000000A8 32 read-only 0x00000000 P0 Output Write Status. 0 1 read-only P1 Output Write Status. 1 1 read-only P2 Output Write Status. 2 1 read-only P3 Output Write Status. 3 1 read-only P4 Output Write Status. 4 1 read-only P5 Output Write Status. 5 1 read-only P6 Output Write Status. 6 1 read-only P7 Output Write Status. 7 1 read-only P8 Output Write Status. 8 1 read-only P9 Output Write Status. 9 1 read-only P10 Output Write Status. 10 1 read-only P11 Output Write Status. 11 1 read-only P12 Output Write Status. 12 1 read-only P13 Output Write Status. 13 1 read-only P14 Output Write Status. 14 1 read-only P15 Output Write Status. 15 1 read-only P16 Output Write Status. 16 1 read-only P17 Output Write Status. 17 1 read-only P18 Output Write Status. 18 1 read-only P19 Output Write Status. 19 1 read-only P20 Output Write Status. 20 1 read-only P21 Output Write Status. 21 1 read-only P22 Output Write Status. 22 1 read-only P23 Output Write Status. 23 1 read-only P24 Output Write Status. 24 1 read-only P25 Output Write Status. 25 1 read-only P26 Output Write Status. 26 1 read-only P27 Output Write Status. 27 1 read-only P28 Output Write Status. 28 1 read-only P29 Output Write Status. 29 1 read-only P30 Output Write Status. 30 1 read-only P31 Output Write Status. 31 1 read-only PIOB 6057E Parallel Input/Output Controller B PIO PIOB_ 0xFFFFF600 0 0x200 registers PIOB 3 PER PIO Enable Register 0x00000000 32 write-only P0 PIO Enable 0 1 write-only P1 PIO Enable 1 1 write-only P2 PIO Enable 2 1 write-only P3 PIO Enable 3 1 write-only P4 PIO Enable 4 1 write-only P5 PIO Enable 5 1 write-only P6 PIO Enable 6 1 write-only P7 PIO Enable 7 1 write-only P8 PIO Enable 8 1 write-only P9 PIO Enable 9 1 write-only P10 PIO Enable 10 1 write-only P11 PIO Enable 11 1 write-only P12 PIO Enable 12 1 write-only P13 PIO Enable 13 1 write-only P14 PIO Enable 14 1 write-only P15 PIO Enable 15 1 write-only P16 PIO Enable 16 1 write-only P17 PIO Enable 17 1 write-only P18 PIO Enable 18 1 write-only P19 PIO Enable 19 1 write-only P20 PIO Enable 20 1 write-only P21 PIO Enable 21 1 write-only P22 PIO Enable 22 1 write-only P23 PIO Enable 23 1 write-only P24 PIO Enable 24 1 write-only P25 PIO Enable 25 1 write-only P26 PIO Enable 26 1 write-only P27 PIO Enable 27 1 write-only P28 PIO Enable 28 1 write-only P29 PIO Enable 29 1 write-only P30 PIO Enable 30 1 write-only P31 PIO Enable 31 1 write-only PDR PIO Disable Register 0x00000004 32 write-only P0 PIO Disable 0 1 write-only P1 PIO Disable 1 1 write-only P2 PIO Disable 2 1 write-only P3 PIO Disable 3 1 write-only P4 PIO Disable 4 1 write-only P5 PIO Disable 5 1 write-only P6 PIO Disable 6 1 write-only P7 PIO Disable 7 1 write-only P8 PIO Disable 8 1 write-only P9 PIO Disable 9 1 write-only P10 PIO Disable 10 1 write-only P11 PIO Disable 11 1 write-only P12 PIO Disable 12 1 write-only P13 PIO Disable 13 1 write-only P14 PIO Disable 14 1 write-only P15 PIO Disable 15 1 write-only P16 PIO Disable 16 1 write-only P17 PIO Disable 17 1 write-only P18 PIO Disable 18 1 write-only P19 PIO Disable 19 1 write-only P20 PIO Disable 20 1 write-only P21 PIO Disable 21 1 write-only P22 PIO Disable 22 1 write-only P23 PIO Disable 23 1 write-only P24 PIO Disable 24 1 write-only P25 PIO Disable 25 1 write-only P26 PIO Disable 26 1 write-only P27 PIO Disable 27 1 write-only P28 PIO Disable 28 1 write-only P29 PIO Disable 29 1 write-only P30 PIO Disable 30 1 write-only P31 PIO Disable 31 1 write-only PSR PIO Status Register 0x00000008 32 read-only P0 PIO Status 0 1 read-only P1 PIO Status 1 1 read-only P2 PIO Status 2 1 read-only P3 PIO Status 3 1 read-only P4 PIO Status 4 1 read-only P5 PIO Status 5 1 read-only P6 PIO Status 6 1 read-only P7 PIO Status 7 1 read-only P8 PIO Status 8 1 read-only P9 PIO Status 9 1 read-only P10 PIO Status 10 1 read-only P11 PIO Status 11 1 read-only P12 PIO Status 12 1 read-only P13 PIO Status 13 1 read-only P14 PIO Status 14 1 read-only P15 PIO Status 15 1 read-only P16 PIO Status 16 1 read-only P17 PIO Status 17 1 read-only P18 PIO Status 18 1 read-only P19 PIO Status 19 1 read-only P20 PIO Status 20 1 read-only P21 PIO Status 21 1 read-only P22 PIO Status 22 1 read-only P23 PIO Status 23 1 read-only P24 PIO Status 24 1 read-only P25 PIO Status 25 1 read-only P26 PIO Status 26 1 read-only P27 PIO Status 27 1 read-only P28 PIO Status 28 1 read-only P29 PIO Status 29 1 read-only P30 PIO Status 30 1 read-only P31 PIO Status 31 1 read-only OER Output Enable Register 0x00000010 32 write-only P0 Output Enable 0 1 write-only P1 Output Enable 1 1 write-only P2 Output Enable 2 1 write-only P3 Output Enable 3 1 write-only P4 Output Enable 4 1 write-only P5 Output Enable 5 1 write-only P6 Output Enable 6 1 write-only P7 Output Enable 7 1 write-only P8 Output Enable 8 1 write-only P9 Output Enable 9 1 write-only P10 Output Enable 10 1 write-only P11 Output Enable 11 1 write-only P12 Output Enable 12 1 write-only P13 Output Enable 13 1 write-only P14 Output Enable 14 1 write-only P15 Output Enable 15 1 write-only P16 Output Enable 16 1 write-only P17 Output Enable 17 1 write-only P18 Output Enable 18 1 write-only P19 Output Enable 19 1 write-only P20 Output Enable 20 1 write-only P21 Output Enable 21 1 write-only P22 Output Enable 22 1 write-only P23 Output Enable 23 1 write-only P24 Output Enable 24 1 write-only P25 Output Enable 25 1 write-only P26 Output Enable 26 1 write-only P27 Output Enable 27 1 write-only P28 Output Enable 28 1 write-only P29 Output Enable 29 1 write-only P30 Output Enable 30 1 write-only P31 Output Enable 31 1 write-only ODR Output Disable Register 0x00000014 32 write-only P0 Output Disable 0 1 write-only P1 Output Disable 1 1 write-only P2 Output Disable 2 1 write-only P3 Output Disable 3 1 write-only P4 Output Disable 4 1 write-only P5 Output Disable 5 1 write-only P6 Output Disable 6 1 write-only P7 Output Disable 7 1 write-only P8 Output Disable 8 1 write-only P9 Output Disable 9 1 write-only P10 Output Disable 10 1 write-only P11 Output Disable 11 1 write-only P12 Output Disable 12 1 write-only P13 Output Disable 13 1 write-only P14 Output Disable 14 1 write-only P15 Output Disable 15 1 write-only P16 Output Disable 16 1 write-only P17 Output Disable 17 1 write-only P18 Output Disable 18 1 write-only P19 Output Disable 19 1 write-only P20 Output Disable 20 1 write-only P21 Output Disable 21 1 write-only P22 Output Disable 22 1 write-only P23 Output Disable 23 1 write-only P24 Output Disable 24 1 write-only P25 Output Disable 25 1 write-only P26 Output Disable 26 1 write-only P27 Output Disable 27 1 write-only P28 Output Disable 28 1 write-only P29 Output Disable 29 1 write-only P30 Output Disable 30 1 write-only P31 Output Disable 31 1 write-only OSR Output Status Register 0x00000018 32 read-only 0x00000000 P0 Output Status 0 1 read-only P1 Output Status 1 1 read-only P2 Output Status 2 1 read-only P3 Output Status 3 1 read-only P4 Output Status 4 1 read-only P5 Output Status 5 1 read-only P6 Output Status 6 1 read-only P7 Output Status 7 1 read-only P8 Output Status 8 1 read-only P9 Output Status 9 1 read-only P10 Output Status 10 1 read-only P11 Output Status 11 1 read-only P12 Output Status 12 1 read-only P13 Output Status 13 1 read-only P14 Output Status 14 1 read-only P15 Output Status 15 1 read-only P16 Output Status 16 1 read-only P17 Output Status 17 1 read-only P18 Output Status 18 1 read-only P19 Output Status 19 1 read-only P20 Output Status 20 1 read-only P21 Output Status 21 1 read-only P22 Output Status 22 1 read-only P23 Output Status 23 1 read-only P24 Output Status 24 1 read-only P25 Output Status 25 1 read-only P26 Output Status 26 1 read-only P27 Output Status 27 1 read-only P28 Output Status 28 1 read-only P29 Output Status 29 1 read-only P30 Output Status 30 1 read-only P31 Output Status 31 1 read-only IFER Glitch Input Filter Enable Register 0x00000020 32 write-only P0 Input Filter Enable 0 1 write-only P1 Input Filter Enable 1 1 write-only P2 Input Filter Enable 2 1 write-only P3 Input Filter Enable 3 1 write-only P4 Input Filter Enable 4 1 write-only P5 Input Filter Enable 5 1 write-only P6 Input Filter Enable 6 1 write-only P7 Input Filter Enable 7 1 write-only P8 Input Filter Enable 8 1 write-only P9 Input Filter Enable 9 1 write-only P10 Input Filter Enable 10 1 write-only P11 Input Filter Enable 11 1 write-only P12 Input Filter Enable 12 1 write-only P13 Input Filter Enable 13 1 write-only P14 Input Filter Enable 14 1 write-only P15 Input Filter Enable 15 1 write-only P16 Input Filter Enable 16 1 write-only P17 Input Filter Enable 17 1 write-only P18 Input Filter Enable 18 1 write-only P19 Input Filter Enable 19 1 write-only P20 Input Filter Enable 20 1 write-only P21 Input Filter Enable 21 1 write-only P22 Input Filter Enable 22 1 write-only P23 Input Filter Enable 23 1 write-only P24 Input Filter Enable 24 1 write-only P25 Input Filter Enable 25 1 write-only P26 Input Filter Enable 26 1 write-only P27 Input Filter Enable 27 1 write-only P28 Input Filter Enable 28 1 write-only P29 Input Filter Enable 29 1 write-only P30 Input Filter Enable 30 1 write-only P31 Input Filter Enable 31 1 write-only IFDR Glitch Input Filter Disable Register 0x00000024 32 write-only P0 Input Filter Disable 0 1 write-only P1 Input Filter Disable 1 1 write-only P2 Input Filter Disable 2 1 write-only P3 Input Filter Disable 3 1 write-only P4 Input Filter Disable 4 1 write-only P5 Input Filter Disable 5 1 write-only P6 Input Filter Disable 6 1 write-only P7 Input Filter Disable 7 1 write-only P8 Input Filter Disable 8 1 write-only P9 Input Filter Disable 9 1 write-only P10 Input Filter Disable 10 1 write-only P11 Input Filter Disable 11 1 write-only P12 Input Filter Disable 12 1 write-only P13 Input Filter Disable 13 1 write-only P14 Input Filter Disable 14 1 write-only P15 Input Filter Disable 15 1 write-only P16 Input Filter Disable 16 1 write-only P17 Input Filter Disable 17 1 write-only P18 Input Filter Disable 18 1 write-only P19 Input Filter Disable 19 1 write-only P20 Input Filter Disable 20 1 write-only P21 Input Filter Disable 21 1 write-only P22 Input Filter Disable 22 1 write-only P23 Input Filter Disable 23 1 write-only P24 Input Filter Disable 24 1 write-only P25 Input Filter Disable 25 1 write-only P26 Input Filter Disable 26 1 write-only P27 Input Filter Disable 27 1 write-only P28 Input Filter Disable 28 1 write-only P29 Input Filter Disable 29 1 write-only P30 Input Filter Disable 30 1 write-only P31 Input Filter Disable 31 1 write-only IFSR Glitch Input Filter Status Register 0x00000028 32 read-only 0x00000000 P0 Input Filer Status 0 1 read-only P1 Input Filer Status 1 1 read-only P2 Input Filer Status 2 1 read-only P3 Input Filer Status 3 1 read-only P4 Input Filer Status 4 1 read-only P5 Input Filer Status 5 1 read-only P6 Input Filer Status 6 1 read-only P7 Input Filer Status 7 1 read-only P8 Input Filer Status 8 1 read-only P9 Input Filer Status 9 1 read-only P10 Input Filer Status 10 1 read-only P11 Input Filer Status 11 1 read-only P12 Input Filer Status 12 1 read-only P13 Input Filer Status 13 1 read-only P14 Input Filer Status 14 1 read-only P15 Input Filer Status 15 1 read-only P16 Input Filer Status 16 1 read-only P17 Input Filer Status 17 1 read-only P18 Input Filer Status 18 1 read-only P19 Input Filer Status 19 1 read-only P20 Input Filer Status 20 1 read-only P21 Input Filer Status 21 1 read-only P22 Input Filer Status 22 1 read-only P23 Input Filer Status 23 1 read-only P24 Input Filer Status 24 1 read-only P25 Input Filer Status 25 1 read-only P26 Input Filer Status 26 1 read-only P27 Input Filer Status 27 1 read-only P28 Input Filer Status 28 1 read-only P29 Input Filer Status 29 1 read-only P30 Input Filer Status 30 1 read-only P31 Input Filer Status 31 1 read-only SODR Set Output Data Register 0x00000030 32 write-only P0 Set Output Data 0 1 write-only P1 Set Output Data 1 1 write-only P2 Set Output Data 2 1 write-only P3 Set Output Data 3 1 write-only P4 Set Output Data 4 1 write-only P5 Set Output Data 5 1 write-only P6 Set Output Data 6 1 write-only P7 Set Output Data 7 1 write-only P8 Set Output Data 8 1 write-only P9 Set Output Data 9 1 write-only P10 Set Output Data 10 1 write-only P11 Set Output Data 11 1 write-only P12 Set Output Data 12 1 write-only P13 Set Output Data 13 1 write-only P14 Set Output Data 14 1 write-only P15 Set Output Data 15 1 write-only P16 Set Output Data 16 1 write-only P17 Set Output Data 17 1 write-only P18 Set Output Data 18 1 write-only P19 Set Output Data 19 1 write-only P20 Set Output Data 20 1 write-only P21 Set Output Data 21 1 write-only P22 Set Output Data 22 1 write-only P23 Set Output Data 23 1 write-only P24 Set Output Data 24 1 write-only P25 Set Output Data 25 1 write-only P26 Set Output Data 26 1 write-only P27 Set Output Data 27 1 write-only P28 Set Output Data 28 1 write-only P29 Set Output Data 29 1 write-only P30 Set Output Data 30 1 write-only P31 Set Output Data 31 1 write-only CODR Clear Output Data Register 0x00000034 32 write-only P0 Set Output Data 0 1 write-only P1 Set Output Data 1 1 write-only P2 Set Output Data 2 1 write-only P3 Set Output Data 3 1 write-only P4 Set Output Data 4 1 write-only P5 Set Output Data 5 1 write-only P6 Set Output Data 6 1 write-only P7 Set Output Data 7 1 write-only P8 Set Output Data 8 1 write-only P9 Set Output Data 9 1 write-only P10 Set Output Data 10 1 write-only P11 Set Output Data 11 1 write-only P12 Set Output Data 12 1 write-only P13 Set Output Data 13 1 write-only P14 Set Output Data 14 1 write-only P15 Set Output Data 15 1 write-only P16 Set Output Data 16 1 write-only P17 Set Output Data 17 1 write-only P18 Set Output Data 18 1 write-only P19 Set Output Data 19 1 write-only P20 Set Output Data 20 1 write-only P21 Set Output Data 21 1 write-only P22 Set Output Data 22 1 write-only P23 Set Output Data 23 1 write-only P24 Set Output Data 24 1 write-only P25 Set Output Data 25 1 write-only P26 Set Output Data 26 1 write-only P27 Set Output Data 27 1 write-only P28 Set Output Data 28 1 write-only P29 Set Output Data 29 1 write-only P30 Set Output Data 30 1 write-only P31 Set Output Data 31 1 write-only ODSR Output Data Status Register 0x00000038 32 read-write P0 Output Data Status 0 1 read-write P1 Output Data Status 1 1 read-write P2 Output Data Status 2 1 read-write P3 Output Data Status 3 1 read-write P4 Output Data Status 4 1 read-write P5 Output Data Status 5 1 read-write P6 Output Data Status 6 1 read-write P7 Output Data Status 7 1 read-write P8 Output Data Status 8 1 read-write P9 Output Data Status 9 1 read-write P10 Output Data Status 10 1 read-write P11 Output Data Status 11 1 read-write P12 Output Data Status 12 1 read-write P13 Output Data Status 13 1 read-write P14 Output Data Status 14 1 read-write P15 Output Data Status 15 1 read-write P16 Output Data Status 16 1 read-write P17 Output Data Status 17 1 read-write P18 Output Data Status 18 1 read-write P19 Output Data Status 19 1 read-write P20 Output Data Status 20 1 read-write P21 Output Data Status 21 1 read-write P22 Output Data Status 22 1 read-write P23 Output Data Status 23 1 read-write P24 Output Data Status 24 1 read-write P25 Output Data Status 25 1 read-write P26 Output Data Status 26 1 read-write P27 Output Data Status 27 1 read-write P28 Output Data Status 28 1 read-write P29 Output Data Status 29 1 read-write P30 Output Data Status 30 1 read-write P31 Output Data Status 31 1 read-write PDSR Pin Data Status Register 0x0000003C 32 read-only P0 Output Data Status 0 1 read-only P1 Output Data Status 1 1 read-only P2 Output Data Status 2 1 read-only P3 Output Data Status 3 1 read-only P4 Output Data Status 4 1 read-only P5 Output Data Status 5 1 read-only P6 Output Data Status 6 1 read-only P7 Output Data Status 7 1 read-only P8 Output Data Status 8 1 read-only P9 Output Data Status 9 1 read-only P10 Output Data Status 10 1 read-only P11 Output Data Status 11 1 read-only P12 Output Data Status 12 1 read-only P13 Output Data Status 13 1 read-only P14 Output Data Status 14 1 read-only P15 Output Data Status 15 1 read-only P16 Output Data Status 16 1 read-only P17 Output Data Status 17 1 read-only P18 Output Data Status 18 1 read-only P19 Output Data Status 19 1 read-only P20 Output Data Status 20 1 read-only P21 Output Data Status 21 1 read-only P22 Output Data Status 22 1 read-only P23 Output Data Status 23 1 read-only P24 Output Data Status 24 1 read-only P25 Output Data Status 25 1 read-only P26 Output Data Status 26 1 read-only P27 Output Data Status 27 1 read-only P28 Output Data Status 28 1 read-only P29 Output Data Status 29 1 read-only P30 Output Data Status 30 1 read-only P31 Output Data Status 31 1 read-only IER Interrupt Enable Register 0x00000040 32 write-only P0 Input Change Interrupt Enable 0 1 write-only P1 Input Change Interrupt Enable 1 1 write-only P2 Input Change Interrupt Enable 2 1 write-only P3 Input Change Interrupt Enable 3 1 write-only P4 Input Change Interrupt Enable 4 1 write-only P5 Input Change Interrupt Enable 5 1 write-only P6 Input Change Interrupt Enable 6 1 write-only P7 Input Change Interrupt Enable 7 1 write-only P8 Input Change Interrupt Enable 8 1 write-only P9 Input Change Interrupt Enable 9 1 write-only P10 Input Change Interrupt Enable 10 1 write-only P11 Input Change Interrupt Enable 11 1 write-only P12 Input Change Interrupt Enable 12 1 write-only P13 Input Change Interrupt Enable 13 1 write-only P14 Input Change Interrupt Enable 14 1 write-only P15 Input Change Interrupt Enable 15 1 write-only P16 Input Change Interrupt Enable 16 1 write-only P17 Input Change Interrupt Enable 17 1 write-only P18 Input Change Interrupt Enable 18 1 write-only P19 Input Change Interrupt Enable 19 1 write-only P20 Input Change Interrupt Enable 20 1 write-only P21 Input Change Interrupt Enable 21 1 write-only P22 Input Change Interrupt Enable 22 1 write-only P23 Input Change Interrupt Enable 23 1 write-only P24 Input Change Interrupt Enable 24 1 write-only P25 Input Change Interrupt Enable 25 1 write-only P26 Input Change Interrupt Enable 26 1 write-only P27 Input Change Interrupt Enable 27 1 write-only P28 Input Change Interrupt Enable 28 1 write-only P29 Input Change Interrupt Enable 29 1 write-only P30 Input Change Interrupt Enable 30 1 write-only P31 Input Change Interrupt Enable 31 1 write-only IDR Interrupt Disable Register 0x00000044 32 write-only P0 Input Change Interrupt Disable 0 1 write-only P1 Input Change Interrupt Disable 1 1 write-only P2 Input Change Interrupt Disable 2 1 write-only P3 Input Change Interrupt Disable 3 1 write-only P4 Input Change Interrupt Disable 4 1 write-only P5 Input Change Interrupt Disable 5 1 write-only P6 Input Change Interrupt Disable 6 1 write-only P7 Input Change Interrupt Disable 7 1 write-only P8 Input Change Interrupt Disable 8 1 write-only P9 Input Change Interrupt Disable 9 1 write-only P10 Input Change Interrupt Disable 10 1 write-only P11 Input Change Interrupt Disable 11 1 write-only P12 Input Change Interrupt Disable 12 1 write-only P13 Input Change Interrupt Disable 13 1 write-only P14 Input Change Interrupt Disable 14 1 write-only P15 Input Change Interrupt Disable 15 1 write-only P16 Input Change Interrupt Disable 16 1 write-only P17 Input Change Interrupt Disable 17 1 write-only P18 Input Change Interrupt Disable 18 1 write-only P19 Input Change Interrupt Disable 19 1 write-only P20 Input Change Interrupt Disable 20 1 write-only P21 Input Change Interrupt Disable 21 1 write-only P22 Input Change Interrupt Disable 22 1 write-only P23 Input Change Interrupt Disable 23 1 write-only P24 Input Change Interrupt Disable 24 1 write-only P25 Input Change Interrupt Disable 25 1 write-only P26 Input Change Interrupt Disable 26 1 write-only P27 Input Change Interrupt Disable 27 1 write-only P28 Input Change Interrupt Disable 28 1 write-only P29 Input Change Interrupt Disable 29 1 write-only P30 Input Change Interrupt Disable 30 1 write-only P31 Input Change Interrupt Disable 31 1 write-only IMR Interrupt Mask Register 0x00000048 32 read-only 0x00000000 P0 Input Change Interrupt Mask 0 1 read-only P1 Input Change Interrupt Mask 1 1 read-only P2 Input Change Interrupt Mask 2 1 read-only P3 Input Change Interrupt Mask 3 1 read-only P4 Input Change Interrupt Mask 4 1 read-only P5 Input Change Interrupt Mask 5 1 read-only P6 Input Change Interrupt Mask 6 1 read-only P7 Input Change Interrupt Mask 7 1 read-only P8 Input Change Interrupt Mask 8 1 read-only P9 Input Change Interrupt Mask 9 1 read-only P10 Input Change Interrupt Mask 10 1 read-only P11 Input Change Interrupt Mask 11 1 read-only P12 Input Change Interrupt Mask 12 1 read-only P13 Input Change Interrupt Mask 13 1 read-only P14 Input Change Interrupt Mask 14 1 read-only P15 Input Change Interrupt Mask 15 1 read-only P16 Input Change Interrupt Mask 16 1 read-only P17 Input Change Interrupt Mask 17 1 read-only P18 Input Change Interrupt Mask 18 1 read-only P19 Input Change Interrupt Mask 19 1 read-only P20 Input Change Interrupt Mask 20 1 read-only P21 Input Change Interrupt Mask 21 1 read-only P22 Input Change Interrupt Mask 22 1 read-only P23 Input Change Interrupt Mask 23 1 read-only P24 Input Change Interrupt Mask 24 1 read-only P25 Input Change Interrupt Mask 25 1 read-only P26 Input Change Interrupt Mask 26 1 read-only P27 Input Change Interrupt Mask 27 1 read-only P28 Input Change Interrupt Mask 28 1 read-only P29 Input Change Interrupt Mask 29 1 read-only P30 Input Change Interrupt Mask 30 1 read-only P31 Input Change Interrupt Mask 31 1 read-only ISR Interrupt Status Register 0x0000004C 32 read-only 0x00000000 P0 Input Change Interrupt Status 0 1 read-only P1 Input Change Interrupt Status 1 1 read-only P2 Input Change Interrupt Status 2 1 read-only P3 Input Change Interrupt Status 3 1 read-only P4 Input Change Interrupt Status 4 1 read-only P5 Input Change Interrupt Status 5 1 read-only P6 Input Change Interrupt Status 6 1 read-only P7 Input Change Interrupt Status 7 1 read-only P8 Input Change Interrupt Status 8 1 read-only P9 Input Change Interrupt Status 9 1 read-only P10 Input Change Interrupt Status 10 1 read-only P11 Input Change Interrupt Status 11 1 read-only P12 Input Change Interrupt Status 12 1 read-only P13 Input Change Interrupt Status 13 1 read-only P14 Input Change Interrupt Status 14 1 read-only P15 Input Change Interrupt Status 15 1 read-only P16 Input Change Interrupt Status 16 1 read-only P17 Input Change Interrupt Status 17 1 read-only P18 Input Change Interrupt Status 18 1 read-only P19 Input Change Interrupt Status 19 1 read-only P20 Input Change Interrupt Status 20 1 read-only P21 Input Change Interrupt Status 21 1 read-only P22 Input Change Interrupt Status 22 1 read-only P23 Input Change Interrupt Status 23 1 read-only P24 Input Change Interrupt Status 24 1 read-only P25 Input Change Interrupt Status 25 1 read-only P26 Input Change Interrupt Status 26 1 read-only P27 Input Change Interrupt Status 27 1 read-only P28 Input Change Interrupt Status 28 1 read-only P29 Input Change Interrupt Status 29 1 read-only P30 Input Change Interrupt Status 30 1 read-only P31 Input Change Interrupt Status 31 1 read-only MDER Multi-driver Enable Register 0x00000050 32 write-only P0 Multi Drive Enable. 0 1 write-only P1 Multi Drive Enable. 1 1 write-only P2 Multi Drive Enable. 2 1 write-only P3 Multi Drive Enable. 3 1 write-only P4 Multi Drive Enable. 4 1 write-only P5 Multi Drive Enable. 5 1 write-only P6 Multi Drive Enable. 6 1 write-only P7 Multi Drive Enable. 7 1 write-only P8 Multi Drive Enable. 8 1 write-only P9 Multi Drive Enable. 9 1 write-only P10 Multi Drive Enable. 10 1 write-only P11 Multi Drive Enable. 11 1 write-only P12 Multi Drive Enable. 12 1 write-only P13 Multi Drive Enable. 13 1 write-only P14 Multi Drive Enable. 14 1 write-only P15 Multi Drive Enable. 15 1 write-only P16 Multi Drive Enable. 16 1 write-only P17 Multi Drive Enable. 17 1 write-only P18 Multi Drive Enable. 18 1 write-only P19 Multi Drive Enable. 19 1 write-only P20 Multi Drive Enable. 20 1 write-only P21 Multi Drive Enable. 21 1 write-only P22 Multi Drive Enable. 22 1 write-only P23 Multi Drive Enable. 23 1 write-only P24 Multi Drive Enable. 24 1 write-only P25 Multi Drive Enable. 25 1 write-only P26 Multi Drive Enable. 26 1 write-only P27 Multi Drive Enable. 27 1 write-only P28 Multi Drive Enable. 28 1 write-only P29 Multi Drive Enable. 29 1 write-only P30 Multi Drive Enable. 30 1 write-only P31 Multi Drive Enable. 31 1 write-only MDDR Multi-driver Disable Register 0x00000054 32 write-only P0 Multi Drive Disable. 0 1 write-only P1 Multi Drive Disable. 1 1 write-only P2 Multi Drive Disable. 2 1 write-only P3 Multi Drive Disable. 3 1 write-only P4 Multi Drive Disable. 4 1 write-only P5 Multi Drive Disable. 5 1 write-only P6 Multi Drive Disable. 6 1 write-only P7 Multi Drive Disable. 7 1 write-only P8 Multi Drive Disable. 8 1 write-only P9 Multi Drive Disable. 9 1 write-only P10 Multi Drive Disable. 10 1 write-only P11 Multi Drive Disable. 11 1 write-only P12 Multi Drive Disable. 12 1 write-only P13 Multi Drive Disable. 13 1 write-only P14 Multi Drive Disable. 14 1 write-only P15 Multi Drive Disable. 15 1 write-only P16 Multi Drive Disable. 16 1 write-only P17 Multi Drive Disable. 17 1 write-only P18 Multi Drive Disable. 18 1 write-only P19 Multi Drive Disable. 19 1 write-only P20 Multi Drive Disable. 20 1 write-only P21 Multi Drive Disable. 21 1 write-only P22 Multi Drive Disable. 22 1 write-only P23 Multi Drive Disable. 23 1 write-only P24 Multi Drive Disable. 24 1 write-only P25 Multi Drive Disable. 25 1 write-only P26 Multi Drive Disable. 26 1 write-only P27 Multi Drive Disable. 27 1 write-only P28 Multi Drive Disable. 28 1 write-only P29 Multi Drive Disable. 29 1 write-only P30 Multi Drive Disable. 30 1 write-only P31 Multi Drive Disable. 31 1 write-only MDSR Multi-driver Status Register 0x00000058 32 read-only 0x00000000 P0 Multi Drive Status. 0 1 read-only P1 Multi Drive Status. 1 1 read-only P2 Multi Drive Status. 2 1 read-only P3 Multi Drive Status. 3 1 read-only P4 Multi Drive Status. 4 1 read-only P5 Multi Drive Status. 5 1 read-only P6 Multi Drive Status. 6 1 read-only P7 Multi Drive Status. 7 1 read-only P8 Multi Drive Status. 8 1 read-only P9 Multi Drive Status. 9 1 read-only P10 Multi Drive Status. 10 1 read-only P11 Multi Drive Status. 11 1 read-only P12 Multi Drive Status. 12 1 read-only P13 Multi Drive Status. 13 1 read-only P14 Multi Drive Status. 14 1 read-only P15 Multi Drive Status. 15 1 read-only P16 Multi Drive Status. 16 1 read-only P17 Multi Drive Status. 17 1 read-only P18 Multi Drive Status. 18 1 read-only P19 Multi Drive Status. 19 1 read-only P20 Multi Drive Status. 20 1 read-only P21 Multi Drive Status. 21 1 read-only P22 Multi Drive Status. 22 1 read-only P23 Multi Drive Status. 23 1 read-only P24 Multi Drive Status. 24 1 read-only P25 Multi Drive Status. 25 1 read-only P26 Multi Drive Status. 26 1 read-only P27 Multi Drive Status. 27 1 read-only P28 Multi Drive Status. 28 1 read-only P29 Multi Drive Status. 29 1 read-only P30 Multi Drive Status. 30 1 read-only P31 Multi Drive Status. 31 1 read-only PUDR Pull-up Disable Register 0x00000060 32 write-only P0 Pull Up Disable. 0 1 write-only P1 Pull Up Disable. 1 1 write-only P2 Pull Up Disable. 2 1 write-only P3 Pull Up Disable. 3 1 write-only P4 Pull Up Disable. 4 1 write-only P5 Pull Up Disable. 5 1 write-only P6 Pull Up Disable. 6 1 write-only P7 Pull Up Disable. 7 1 write-only P8 Pull Up Disable. 8 1 write-only P9 Pull Up Disable. 9 1 write-only P10 Pull Up Disable. 10 1 write-only P11 Pull Up Disable. 11 1 write-only P12 Pull Up Disable. 12 1 write-only P13 Pull Up Disable. 13 1 write-only P14 Pull Up Disable. 14 1 write-only P15 Pull Up Disable. 15 1 write-only P16 Pull Up Disable. 16 1 write-only P17 Pull Up Disable. 17 1 write-only P18 Pull Up Disable. 18 1 write-only P19 Pull Up Disable. 19 1 write-only P20 Pull Up Disable. 20 1 write-only P21 Pull Up Disable. 21 1 write-only P22 Pull Up Disable. 22 1 write-only P23 Pull Up Disable. 23 1 write-only P24 Pull Up Disable. 24 1 write-only P25 Pull Up Disable. 25 1 write-only P26 Pull Up Disable. 26 1 write-only P27 Pull Up Disable. 27 1 write-only P28 Pull Up Disable. 28 1 write-only P29 Pull Up Disable. 29 1 write-only P30 Pull Up Disable. 30 1 write-only P31 Pull Up Disable. 31 1 write-only PUER Pull-up Enable Register 0x00000064 32 write-only P0 Pull Up Enable. 0 1 write-only P1 Pull Up Enable. 1 1 write-only P2 Pull Up Enable. 2 1 write-only P3 Pull Up Enable. 3 1 write-only P4 Pull Up Enable. 4 1 write-only P5 Pull Up Enable. 5 1 write-only P6 Pull Up Enable. 6 1 write-only P7 Pull Up Enable. 7 1 write-only P8 Pull Up Enable. 8 1 write-only P9 Pull Up Enable. 9 1 write-only P10 Pull Up Enable. 10 1 write-only P11 Pull Up Enable. 11 1 write-only P12 Pull Up Enable. 12 1 write-only P13 Pull Up Enable. 13 1 write-only P14 Pull Up Enable. 14 1 write-only P15 Pull Up Enable. 15 1 write-only P16 Pull Up Enable. 16 1 write-only P17 Pull Up Enable. 17 1 write-only P18 Pull Up Enable. 18 1 write-only P19 Pull Up Enable. 19 1 write-only P20 Pull Up Enable. 20 1 write-only P21 Pull Up Enable. 21 1 write-only P22 Pull Up Enable. 22 1 write-only P23 Pull Up Enable. 23 1 write-only P24 Pull Up Enable. 24 1 write-only P25 Pull Up Enable. 25 1 write-only P26 Pull Up Enable. 26 1 write-only P27 Pull Up Enable. 27 1 write-only P28 Pull Up Enable. 28 1 write-only P29 Pull Up Enable. 29 1 write-only P30 Pull Up Enable. 30 1 write-only P31 Pull Up Enable. 31 1 write-only PUSR Pad Pull-up Status Register 0x00000068 32 read-only 0x00000000 P0 Pull Up Status. 0 1 read-only P1 Pull Up Status. 1 1 read-only P2 Pull Up Status. 2 1 read-only P3 Pull Up Status. 3 1 read-only P4 Pull Up Status. 4 1 read-only P5 Pull Up Status. 5 1 read-only P6 Pull Up Status. 6 1 read-only P7 Pull Up Status. 7 1 read-only P8 Pull Up Status. 8 1 read-only P9 Pull Up Status. 9 1 read-only P10 Pull Up Status. 10 1 read-only P11 Pull Up Status. 11 1 read-only P12 Pull Up Status. 12 1 read-only P13 Pull Up Status. 13 1 read-only P14 Pull Up Status. 14 1 read-only P15 Pull Up Status. 15 1 read-only P16 Pull Up Status. 16 1 read-only P17 Pull Up Status. 17 1 read-only P18 Pull Up Status. 18 1 read-only P19 Pull Up Status. 19 1 read-only P20 Pull Up Status. 20 1 read-only P21 Pull Up Status. 21 1 read-only P22 Pull Up Status. 22 1 read-only P23 Pull Up Status. 23 1 read-only P24 Pull Up Status. 24 1 read-only P25 Pull Up Status. 25 1 read-only P26 Pull Up Status. 26 1 read-only P27 Pull Up Status. 27 1 read-only P28 Pull Up Status. 28 1 read-only P29 Pull Up Status. 29 1 read-only P30 Pull Up Status. 30 1 read-only P31 Pull Up Status. 31 1 read-only ASR Peripheral A Select Register 0x00000070 32 write-only P0 Peripheral A Select. 0 1 write-only P1 Peripheral A Select. 1 1 write-only P2 Peripheral A Select. 2 1 write-only P3 Peripheral A Select. 3 1 write-only P4 Peripheral A Select. 4 1 write-only P5 Peripheral A Select. 5 1 write-only P6 Peripheral A Select. 6 1 write-only P7 Peripheral A Select. 7 1 write-only P8 Peripheral A Select. 8 1 write-only P9 Peripheral A Select. 9 1 write-only P10 Peripheral A Select. 10 1 write-only P11 Peripheral A Select. 11 1 write-only P12 Peripheral A Select. 12 1 write-only P13 Peripheral A Select. 13 1 write-only P14 Peripheral A Select. 14 1 write-only P15 Peripheral A Select. 15 1 write-only P16 Peripheral A Select. 16 1 write-only P17 Peripheral A Select. 17 1 write-only P18 Peripheral A Select. 18 1 write-only P19 Peripheral A Select. 19 1 write-only P20 Peripheral A Select. 20 1 write-only P21 Peripheral A Select. 21 1 write-only P22 Peripheral A Select. 22 1 write-only P23 Peripheral A Select. 23 1 write-only P24 Peripheral A Select. 24 1 write-only P25 Peripheral A Select. 25 1 write-only P26 Peripheral A Select. 26 1 write-only P27 Peripheral A Select. 27 1 write-only P28 Peripheral A Select. 28 1 write-only P29 Peripheral A Select. 29 1 write-only P30 Peripheral A Select. 30 1 write-only P31 Peripheral A Select. 31 1 write-only BSR Peripheral B Select Register 0x00000074 32 write-only P0 Peripheral B Select. 0 1 write-only P1 Peripheral B Select. 1 1 write-only P2 Peripheral B Select. 2 1 write-only P3 Peripheral B Select. 3 1 write-only P4 Peripheral B Select. 4 1 write-only P5 Peripheral B Select. 5 1 write-only P6 Peripheral B Select. 6 1 write-only P7 Peripheral B Select. 7 1 write-only P8 Peripheral B Select. 8 1 write-only P9 Peripheral B Select. 9 1 write-only P10 Peripheral B Select. 10 1 write-only P11 Peripheral B Select. 11 1 write-only P12 Peripheral B Select. 12 1 write-only P13 Peripheral B Select. 13 1 write-only P14 Peripheral B Select. 14 1 write-only P15 Peripheral B Select. 15 1 write-only P16 Peripheral B Select. 16 1 write-only P17 Peripheral B Select. 17 1 write-only P18 Peripheral B Select. 18 1 write-only P19 Peripheral B Select. 19 1 write-only P20 Peripheral B Select. 20 1 write-only P21 Peripheral B Select. 21 1 write-only P22 Peripheral B Select. 22 1 write-only P23 Peripheral B Select. 23 1 write-only P24 Peripheral B Select. 24 1 write-only P25 Peripheral B Select. 25 1 write-only P26 Peripheral B Select. 26 1 write-only P27 Peripheral B Select. 27 1 write-only P28 Peripheral B Select. 28 1 write-only P29 Peripheral B Select. 29 1 write-only P30 Peripheral B Select. 30 1 write-only P31 Peripheral B Select. 31 1 write-only ABSR AB Status Register 0x00000078 32 read-only 0x00000000 P0 Peripheral A B Status. 0 1 read-only P1 Peripheral A B Status. 1 1 read-only P2 Peripheral A B Status. 2 1 read-only P3 Peripheral A B Status. 3 1 read-only P4 Peripheral A B Status. 4 1 read-only P5 Peripheral A B Status. 5 1 read-only P6 Peripheral A B Status. 6 1 read-only P7 Peripheral A B Status. 7 1 read-only P8 Peripheral A B Status. 8 1 read-only P9 Peripheral A B Status. 9 1 read-only P10 Peripheral A B Status. 10 1 read-only P11 Peripheral A B Status. 11 1 read-only P12 Peripheral A B Status. 12 1 read-only P13 Peripheral A B Status. 13 1 read-only P14 Peripheral A B Status. 14 1 read-only P15 Peripheral A B Status. 15 1 read-only P16 Peripheral A B Status. 16 1 read-only P17 Peripheral A B Status. 17 1 read-only P18 Peripheral A B Status. 18 1 read-only P19 Peripheral A B Status. 19 1 read-only P20 Peripheral A B Status. 20 1 read-only P21 Peripheral A B Status. 21 1 read-only P22 Peripheral A B Status. 22 1 read-only P23 Peripheral A B Status. 23 1 read-only P24 Peripheral A B Status. 24 1 read-only P25 Peripheral A B Status. 25 1 read-only P26 Peripheral A B Status. 26 1 read-only P27 Peripheral A B Status. 27 1 read-only P28 Peripheral A B Status. 28 1 read-only P29 Peripheral A B Status. 29 1 read-only P30 Peripheral A B Status. 30 1 read-only P31 Peripheral A B Status. 31 1 read-only OWER Output Write Enable 0x000000A0 32 write-only P0 Output Write Enable. 0 1 write-only P1 Output Write Enable. 1 1 write-only P2 Output Write Enable. 2 1 write-only P3 Output Write Enable. 3 1 write-only P4 Output Write Enable. 4 1 write-only P5 Output Write Enable. 5 1 write-only P6 Output Write Enable. 6 1 write-only P7 Output Write Enable. 7 1 write-only P8 Output Write Enable. 8 1 write-only P9 Output Write Enable. 9 1 write-only P10 Output Write Enable. 10 1 write-only P11 Output Write Enable. 11 1 write-only P12 Output Write Enable. 12 1 write-only P13 Output Write Enable. 13 1 write-only P14 Output Write Enable. 14 1 write-only P15 Output Write Enable. 15 1 write-only P16 Output Write Enable. 16 1 write-only P17 Output Write Enable. 17 1 write-only P18 Output Write Enable. 18 1 write-only P19 Output Write Enable. 19 1 write-only P20 Output Write Enable. 20 1 write-only P21 Output Write Enable. 21 1 write-only P22 Output Write Enable. 22 1 write-only P23 Output Write Enable. 23 1 write-only P24 Output Write Enable. 24 1 write-only P25 Output Write Enable. 25 1 write-only P26 Output Write Enable. 26 1 write-only P27 Output Write Enable. 27 1 write-only P28 Output Write Enable. 28 1 write-only P29 Output Write Enable. 29 1 write-only P30 Output Write Enable. 30 1 write-only P31 Output Write Enable. 31 1 write-only OWDR Output Write Disable 0x000000A4 32 write-only P0 Output Write Disable. 0 1 write-only P1 Output Write Disable. 1 1 write-only P2 Output Write Disable. 2 1 write-only P3 Output Write Disable. 3 1 write-only P4 Output Write Disable. 4 1 write-only P5 Output Write Disable. 5 1 write-only P6 Output Write Disable. 6 1 write-only P7 Output Write Disable. 7 1 write-only P8 Output Write Disable. 8 1 write-only P9 Output Write Disable. 9 1 write-only P10 Output Write Disable. 10 1 write-only P11 Output Write Disable. 11 1 write-only P12 Output Write Disable. 12 1 write-only P13 Output Write Disable. 13 1 write-only P14 Output Write Disable. 14 1 write-only P15 Output Write Disable. 15 1 write-only P16 Output Write Disable. 16 1 write-only P17 Output Write Disable. 17 1 write-only P18 Output Write Disable. 18 1 write-only P19 Output Write Disable. 19 1 write-only P20 Output Write Disable. 20 1 write-only P21 Output Write Disable. 21 1 write-only P22 Output Write Disable. 22 1 write-only P23 Output Write Disable. 23 1 write-only P24 Output Write Disable. 24 1 write-only P25 Output Write Disable. 25 1 write-only P26 Output Write Disable. 26 1 write-only P27 Output Write Disable. 27 1 write-only P28 Output Write Disable. 28 1 write-only P29 Output Write Disable. 29 1 write-only P30 Output Write Disable. 30 1 write-only P31 Output Write Disable. 31 1 write-only OWSR Output Write Status Register 0x000000A8 32 read-only 0x00000000 P0 Output Write Status. 0 1 read-only P1 Output Write Status. 1 1 read-only P2 Output Write Status. 2 1 read-only P3 Output Write Status. 3 1 read-only P4 Output Write Status. 4 1 read-only P5 Output Write Status. 5 1 read-only P6 Output Write Status. 6 1 read-only P7 Output Write Status. 7 1 read-only P8 Output Write Status. 8 1 read-only P9 Output Write Status. 9 1 read-only P10 Output Write Status. 10 1 read-only P11 Output Write Status. 11 1 read-only P12 Output Write Status. 12 1 read-only P13 Output Write Status. 13 1 read-only P14 Output Write Status. 14 1 read-only P15 Output Write Status. 15 1 read-only P16 Output Write Status. 16 1 read-only P17 Output Write Status. 17 1 read-only P18 Output Write Status. 18 1 read-only P19 Output Write Status. 19 1 read-only P20 Output Write Status. 20 1 read-only P21 Output Write Status. 21 1 read-only P22 Output Write Status. 22 1 read-only P23 Output Write Status. 23 1 read-only P24 Output Write Status. 24 1 read-only P25 Output Write Status. 25 1 read-only P26 Output Write Status. 26 1 read-only P27 Output Write Status. 27 1 read-only P28 Output Write Status. 28 1 read-only P29 Output Write Status. 29 1 read-only P30 Output Write Status. 30 1 read-only P31 Output Write Status. 31 1 read-only PIOC 6057E Parallel Input/Output Controller C PIO PIOC_ 0xFFFFF800 0 0x200 registers PIOC 4 PER PIO Enable Register 0x00000000 32 write-only P0 PIO Enable 0 1 write-only P1 PIO Enable 1 1 write-only P2 PIO Enable 2 1 write-only P3 PIO Enable 3 1 write-only P4 PIO Enable 4 1 write-only P5 PIO Enable 5 1 write-only P6 PIO Enable 6 1 write-only P7 PIO Enable 7 1 write-only P8 PIO Enable 8 1 write-only P9 PIO Enable 9 1 write-only P10 PIO Enable 10 1 write-only P11 PIO Enable 11 1 write-only P12 PIO Enable 12 1 write-only P13 PIO Enable 13 1 write-only P14 PIO Enable 14 1 write-only P15 PIO Enable 15 1 write-only P16 PIO Enable 16 1 write-only P17 PIO Enable 17 1 write-only P18 PIO Enable 18 1 write-only P19 PIO Enable 19 1 write-only P20 PIO Enable 20 1 write-only P21 PIO Enable 21 1 write-only P22 PIO Enable 22 1 write-only P23 PIO Enable 23 1 write-only P24 PIO Enable 24 1 write-only P25 PIO Enable 25 1 write-only P26 PIO Enable 26 1 write-only P27 PIO Enable 27 1 write-only P28 PIO Enable 28 1 write-only P29 PIO Enable 29 1 write-only P30 PIO Enable 30 1 write-only P31 PIO Enable 31 1 write-only PDR PIO Disable Register 0x00000004 32 write-only P0 PIO Disable 0 1 write-only P1 PIO Disable 1 1 write-only P2 PIO Disable 2 1 write-only P3 PIO Disable 3 1 write-only P4 PIO Disable 4 1 write-only P5 PIO Disable 5 1 write-only P6 PIO Disable 6 1 write-only P7 PIO Disable 7 1 write-only P8 PIO Disable 8 1 write-only P9 PIO Disable 9 1 write-only P10 PIO Disable 10 1 write-only P11 PIO Disable 11 1 write-only P12 PIO Disable 12 1 write-only P13 PIO Disable 13 1 write-only P14 PIO Disable 14 1 write-only P15 PIO Disable 15 1 write-only P16 PIO Disable 16 1 write-only P17 PIO Disable 17 1 write-only P18 PIO Disable 18 1 write-only P19 PIO Disable 19 1 write-only P20 PIO Disable 20 1 write-only P21 PIO Disable 21 1 write-only P22 PIO Disable 22 1 write-only P23 PIO Disable 23 1 write-only P24 PIO Disable 24 1 write-only P25 PIO Disable 25 1 write-only P26 PIO Disable 26 1 write-only P27 PIO Disable 27 1 write-only P28 PIO Disable 28 1 write-only P29 PIO Disable 29 1 write-only P30 PIO Disable 30 1 write-only P31 PIO Disable 31 1 write-only PSR PIO Status Register 0x00000008 32 read-only P0 PIO Status 0 1 read-only P1 PIO Status 1 1 read-only P2 PIO Status 2 1 read-only P3 PIO Status 3 1 read-only P4 PIO Status 4 1 read-only P5 PIO Status 5 1 read-only P6 PIO Status 6 1 read-only P7 PIO Status 7 1 read-only P8 PIO Status 8 1 read-only P9 PIO Status 9 1 read-only P10 PIO Status 10 1 read-only P11 PIO Status 11 1 read-only P12 PIO Status 12 1 read-only P13 PIO Status 13 1 read-only P14 PIO Status 14 1 read-only P15 PIO Status 15 1 read-only P16 PIO Status 16 1 read-only P17 PIO Status 17 1 read-only P18 PIO Status 18 1 read-only P19 PIO Status 19 1 read-only P20 PIO Status 20 1 read-only P21 PIO Status 21 1 read-only P22 PIO Status 22 1 read-only P23 PIO Status 23 1 read-only P24 PIO Status 24 1 read-only P25 PIO Status 25 1 read-only P26 PIO Status 26 1 read-only P27 PIO Status 27 1 read-only P28 PIO Status 28 1 read-only P29 PIO Status 29 1 read-only P30 PIO Status 30 1 read-only P31 PIO Status 31 1 read-only OER Output Enable Register 0x00000010 32 write-only P0 Output Enable 0 1 write-only P1 Output Enable 1 1 write-only P2 Output Enable 2 1 write-only P3 Output Enable 3 1 write-only P4 Output Enable 4 1 write-only P5 Output Enable 5 1 write-only P6 Output Enable 6 1 write-only P7 Output Enable 7 1 write-only P8 Output Enable 8 1 write-only P9 Output Enable 9 1 write-only P10 Output Enable 10 1 write-only P11 Output Enable 11 1 write-only P12 Output Enable 12 1 write-only P13 Output Enable 13 1 write-only P14 Output Enable 14 1 write-only P15 Output Enable 15 1 write-only P16 Output Enable 16 1 write-only P17 Output Enable 17 1 write-only P18 Output Enable 18 1 write-only P19 Output Enable 19 1 write-only P20 Output Enable 20 1 write-only P21 Output Enable 21 1 write-only P22 Output Enable 22 1 write-only P23 Output Enable 23 1 write-only P24 Output Enable 24 1 write-only P25 Output Enable 25 1 write-only P26 Output Enable 26 1 write-only P27 Output Enable 27 1 write-only P28 Output Enable 28 1 write-only P29 Output Enable 29 1 write-only P30 Output Enable 30 1 write-only P31 Output Enable 31 1 write-only ODR Output Disable Register 0x00000014 32 write-only P0 Output Disable 0 1 write-only P1 Output Disable 1 1 write-only P2 Output Disable 2 1 write-only P3 Output Disable 3 1 write-only P4 Output Disable 4 1 write-only P5 Output Disable 5 1 write-only P6 Output Disable 6 1 write-only P7 Output Disable 7 1 write-only P8 Output Disable 8 1 write-only P9 Output Disable 9 1 write-only P10 Output Disable 10 1 write-only P11 Output Disable 11 1 write-only P12 Output Disable 12 1 write-only P13 Output Disable 13 1 write-only P14 Output Disable 14 1 write-only P15 Output Disable 15 1 write-only P16 Output Disable 16 1 write-only P17 Output Disable 17 1 write-only P18 Output Disable 18 1 write-only P19 Output Disable 19 1 write-only P20 Output Disable 20 1 write-only P21 Output Disable 21 1 write-only P22 Output Disable 22 1 write-only P23 Output Disable 23 1 write-only P24 Output Disable 24 1 write-only P25 Output Disable 25 1 write-only P26 Output Disable 26 1 write-only P27 Output Disable 27 1 write-only P28 Output Disable 28 1 write-only P29 Output Disable 29 1 write-only P30 Output Disable 30 1 write-only P31 Output Disable 31 1 write-only OSR Output Status Register 0x00000018 32 read-only 0x00000000 P0 Output Status 0 1 read-only P1 Output Status 1 1 read-only P2 Output Status 2 1 read-only P3 Output Status 3 1 read-only P4 Output Status 4 1 read-only P5 Output Status 5 1 read-only P6 Output Status 6 1 read-only P7 Output Status 7 1 read-only P8 Output Status 8 1 read-only P9 Output Status 9 1 read-only P10 Output Status 10 1 read-only P11 Output Status 11 1 read-only P12 Output Status 12 1 read-only P13 Output Status 13 1 read-only P14 Output Status 14 1 read-only P15 Output Status 15 1 read-only P16 Output Status 16 1 read-only P17 Output Status 17 1 read-only P18 Output Status 18 1 read-only P19 Output Status 19 1 read-only P20 Output Status 20 1 read-only P21 Output Status 21 1 read-only P22 Output Status 22 1 read-only P23 Output Status 23 1 read-only P24 Output Status 24 1 read-only P25 Output Status 25 1 read-only P26 Output Status 26 1 read-only P27 Output Status 27 1 read-only P28 Output Status 28 1 read-only P29 Output Status 29 1 read-only P30 Output Status 30 1 read-only P31 Output Status 31 1 read-only IFER Glitch Input Filter Enable Register 0x00000020 32 write-only P0 Input Filter Enable 0 1 write-only P1 Input Filter Enable 1 1 write-only P2 Input Filter Enable 2 1 write-only P3 Input Filter Enable 3 1 write-only P4 Input Filter Enable 4 1 write-only P5 Input Filter Enable 5 1 write-only P6 Input Filter Enable 6 1 write-only P7 Input Filter Enable 7 1 write-only P8 Input Filter Enable 8 1 write-only P9 Input Filter Enable 9 1 write-only P10 Input Filter Enable 10 1 write-only P11 Input Filter Enable 11 1 write-only P12 Input Filter Enable 12 1 write-only P13 Input Filter Enable 13 1 write-only P14 Input Filter Enable 14 1 write-only P15 Input Filter Enable 15 1 write-only P16 Input Filter Enable 16 1 write-only P17 Input Filter Enable 17 1 write-only P18 Input Filter Enable 18 1 write-only P19 Input Filter Enable 19 1 write-only P20 Input Filter Enable 20 1 write-only P21 Input Filter Enable 21 1 write-only P22 Input Filter Enable 22 1 write-only P23 Input Filter Enable 23 1 write-only P24 Input Filter Enable 24 1 write-only P25 Input Filter Enable 25 1 write-only P26 Input Filter Enable 26 1 write-only P27 Input Filter Enable 27 1 write-only P28 Input Filter Enable 28 1 write-only P29 Input Filter Enable 29 1 write-only P30 Input Filter Enable 30 1 write-only P31 Input Filter Enable 31 1 write-only IFDR Glitch Input Filter Disable Register 0x00000024 32 write-only P0 Input Filter Disable 0 1 write-only P1 Input Filter Disable 1 1 write-only P2 Input Filter Disable 2 1 write-only P3 Input Filter Disable 3 1 write-only P4 Input Filter Disable 4 1 write-only P5 Input Filter Disable 5 1 write-only P6 Input Filter Disable 6 1 write-only P7 Input Filter Disable 7 1 write-only P8 Input Filter Disable 8 1 write-only P9 Input Filter Disable 9 1 write-only P10 Input Filter Disable 10 1 write-only P11 Input Filter Disable 11 1 write-only P12 Input Filter Disable 12 1 write-only P13 Input Filter Disable 13 1 write-only P14 Input Filter Disable 14 1 write-only P15 Input Filter Disable 15 1 write-only P16 Input Filter Disable 16 1 write-only P17 Input Filter Disable 17 1 write-only P18 Input Filter Disable 18 1 write-only P19 Input Filter Disable 19 1 write-only P20 Input Filter Disable 20 1 write-only P21 Input Filter Disable 21 1 write-only P22 Input Filter Disable 22 1 write-only P23 Input Filter Disable 23 1 write-only P24 Input Filter Disable 24 1 write-only P25 Input Filter Disable 25 1 write-only P26 Input Filter Disable 26 1 write-only P27 Input Filter Disable 27 1 write-only P28 Input Filter Disable 28 1 write-only P29 Input Filter Disable 29 1 write-only P30 Input Filter Disable 30 1 write-only P31 Input Filter Disable 31 1 write-only IFSR Glitch Input Filter Status Register 0x00000028 32 read-only 0x00000000 P0 Input Filer Status 0 1 read-only P1 Input Filer Status 1 1 read-only P2 Input Filer Status 2 1 read-only P3 Input Filer Status 3 1 read-only P4 Input Filer Status 4 1 read-only P5 Input Filer Status 5 1 read-only P6 Input Filer Status 6 1 read-only P7 Input Filer Status 7 1 read-only P8 Input Filer Status 8 1 read-only P9 Input Filer Status 9 1 read-only P10 Input Filer Status 10 1 read-only P11 Input Filer Status 11 1 read-only P12 Input Filer Status 12 1 read-only P13 Input Filer Status 13 1 read-only P14 Input Filer Status 14 1 read-only P15 Input Filer Status 15 1 read-only P16 Input Filer Status 16 1 read-only P17 Input Filer Status 17 1 read-only P18 Input Filer Status 18 1 read-only P19 Input Filer Status 19 1 read-only P20 Input Filer Status 20 1 read-only P21 Input Filer Status 21 1 read-only P22 Input Filer Status 22 1 read-only P23 Input Filer Status 23 1 read-only P24 Input Filer Status 24 1 read-only P25 Input Filer Status 25 1 read-only P26 Input Filer Status 26 1 read-only P27 Input Filer Status 27 1 read-only P28 Input Filer Status 28 1 read-only P29 Input Filer Status 29 1 read-only P30 Input Filer Status 30 1 read-only P31 Input Filer Status 31 1 read-only SODR Set Output Data Register 0x00000030 32 write-only P0 Set Output Data 0 1 write-only P1 Set Output Data 1 1 write-only P2 Set Output Data 2 1 write-only P3 Set Output Data 3 1 write-only P4 Set Output Data 4 1 write-only P5 Set Output Data 5 1 write-only P6 Set Output Data 6 1 write-only P7 Set Output Data 7 1 write-only P8 Set Output Data 8 1 write-only P9 Set Output Data 9 1 write-only P10 Set Output Data 10 1 write-only P11 Set Output Data 11 1 write-only P12 Set Output Data 12 1 write-only P13 Set Output Data 13 1 write-only P14 Set Output Data 14 1 write-only P15 Set Output Data 15 1 write-only P16 Set Output Data 16 1 write-only P17 Set Output Data 17 1 write-only P18 Set Output Data 18 1 write-only P19 Set Output Data 19 1 write-only P20 Set Output Data 20 1 write-only P21 Set Output Data 21 1 write-only P22 Set Output Data 22 1 write-only P23 Set Output Data 23 1 write-only P24 Set Output Data 24 1 write-only P25 Set Output Data 25 1 write-only P26 Set Output Data 26 1 write-only P27 Set Output Data 27 1 write-only P28 Set Output Data 28 1 write-only P29 Set Output Data 29 1 write-only P30 Set Output Data 30 1 write-only P31 Set Output Data 31 1 write-only CODR Clear Output Data Register 0x00000034 32 write-only P0 Set Output Data 0 1 write-only P1 Set Output Data 1 1 write-only P2 Set Output Data 2 1 write-only P3 Set Output Data 3 1 write-only P4 Set Output Data 4 1 write-only P5 Set Output Data 5 1 write-only P6 Set Output Data 6 1 write-only P7 Set Output Data 7 1 write-only P8 Set Output Data 8 1 write-only P9 Set Output Data 9 1 write-only P10 Set Output Data 10 1 write-only P11 Set Output Data 11 1 write-only P12 Set Output Data 12 1 write-only P13 Set Output Data 13 1 write-only P14 Set Output Data 14 1 write-only P15 Set Output Data 15 1 write-only P16 Set Output Data 16 1 write-only P17 Set Output Data 17 1 write-only P18 Set Output Data 18 1 write-only P19 Set Output Data 19 1 write-only P20 Set Output Data 20 1 write-only P21 Set Output Data 21 1 write-only P22 Set Output Data 22 1 write-only P23 Set Output Data 23 1 write-only P24 Set Output Data 24 1 write-only P25 Set Output Data 25 1 write-only P26 Set Output Data 26 1 write-only P27 Set Output Data 27 1 write-only P28 Set Output Data 28 1 write-only P29 Set Output Data 29 1 write-only P30 Set Output Data 30 1 write-only P31 Set Output Data 31 1 write-only ODSR Output Data Status Register 0x00000038 32 read-write P0 Output Data Status 0 1 read-write P1 Output Data Status 1 1 read-write P2 Output Data Status 2 1 read-write P3 Output Data Status 3 1 read-write P4 Output Data Status 4 1 read-write P5 Output Data Status 5 1 read-write P6 Output Data Status 6 1 read-write P7 Output Data Status 7 1 read-write P8 Output Data Status 8 1 read-write P9 Output Data Status 9 1 read-write P10 Output Data Status 10 1 read-write P11 Output Data Status 11 1 read-write P12 Output Data Status 12 1 read-write P13 Output Data Status 13 1 read-write P14 Output Data Status 14 1 read-write P15 Output Data Status 15 1 read-write P16 Output Data Status 16 1 read-write P17 Output Data Status 17 1 read-write P18 Output Data Status 18 1 read-write P19 Output Data Status 19 1 read-write P20 Output Data Status 20 1 read-write P21 Output Data Status 21 1 read-write P22 Output Data Status 22 1 read-write P23 Output Data Status 23 1 read-write P24 Output Data Status 24 1 read-write P25 Output Data Status 25 1 read-write P26 Output Data Status 26 1 read-write P27 Output Data Status 27 1 read-write P28 Output Data Status 28 1 read-write P29 Output Data Status 29 1 read-write P30 Output Data Status 30 1 read-write P31 Output Data Status 31 1 read-write PDSR Pin Data Status Register 0x0000003C 32 read-only P0 Output Data Status 0 1 read-only P1 Output Data Status 1 1 read-only P2 Output Data Status 2 1 read-only P3 Output Data Status 3 1 read-only P4 Output Data Status 4 1 read-only P5 Output Data Status 5 1 read-only P6 Output Data Status 6 1 read-only P7 Output Data Status 7 1 read-only P8 Output Data Status 8 1 read-only P9 Output Data Status 9 1 read-only P10 Output Data Status 10 1 read-only P11 Output Data Status 11 1 read-only P12 Output Data Status 12 1 read-only P13 Output Data Status 13 1 read-only P14 Output Data Status 14 1 read-only P15 Output Data Status 15 1 read-only P16 Output Data Status 16 1 read-only P17 Output Data Status 17 1 read-only P18 Output Data Status 18 1 read-only P19 Output Data Status 19 1 read-only P20 Output Data Status 20 1 read-only P21 Output Data Status 21 1 read-only P22 Output Data Status 22 1 read-only P23 Output Data Status 23 1 read-only P24 Output Data Status 24 1 read-only P25 Output Data Status 25 1 read-only P26 Output Data Status 26 1 read-only P27 Output Data Status 27 1 read-only P28 Output Data Status 28 1 read-only P29 Output Data Status 29 1 read-only P30 Output Data Status 30 1 read-only P31 Output Data Status 31 1 read-only IER Interrupt Enable Register 0x00000040 32 write-only P0 Input Change Interrupt Enable 0 1 write-only P1 Input Change Interrupt Enable 1 1 write-only P2 Input Change Interrupt Enable 2 1 write-only P3 Input Change Interrupt Enable 3 1 write-only P4 Input Change Interrupt Enable 4 1 write-only P5 Input Change Interrupt Enable 5 1 write-only P6 Input Change Interrupt Enable 6 1 write-only P7 Input Change Interrupt Enable 7 1 write-only P8 Input Change Interrupt Enable 8 1 write-only P9 Input Change Interrupt Enable 9 1 write-only P10 Input Change Interrupt Enable 10 1 write-only P11 Input Change Interrupt Enable 11 1 write-only P12 Input Change Interrupt Enable 12 1 write-only P13 Input Change Interrupt Enable 13 1 write-only P14 Input Change Interrupt Enable 14 1 write-only P15 Input Change Interrupt Enable 15 1 write-only P16 Input Change Interrupt Enable 16 1 write-only P17 Input Change Interrupt Enable 17 1 write-only P18 Input Change Interrupt Enable 18 1 write-only P19 Input Change Interrupt Enable 19 1 write-only P20 Input Change Interrupt Enable 20 1 write-only P21 Input Change Interrupt Enable 21 1 write-only P22 Input Change Interrupt Enable 22 1 write-only P23 Input Change Interrupt Enable 23 1 write-only P24 Input Change Interrupt Enable 24 1 write-only P25 Input Change Interrupt Enable 25 1 write-only P26 Input Change Interrupt Enable 26 1 write-only P27 Input Change Interrupt Enable 27 1 write-only P28 Input Change Interrupt Enable 28 1 write-only P29 Input Change Interrupt Enable 29 1 write-only P30 Input Change Interrupt Enable 30 1 write-only P31 Input Change Interrupt Enable 31 1 write-only IDR Interrupt Disable Register 0x00000044 32 write-only P0 Input Change Interrupt Disable 0 1 write-only P1 Input Change Interrupt Disable 1 1 write-only P2 Input Change Interrupt Disable 2 1 write-only P3 Input Change Interrupt Disable 3 1 write-only P4 Input Change Interrupt Disable 4 1 write-only P5 Input Change Interrupt Disable 5 1 write-only P6 Input Change Interrupt Disable 6 1 write-only P7 Input Change Interrupt Disable 7 1 write-only P8 Input Change Interrupt Disable 8 1 write-only P9 Input Change Interrupt Disable 9 1 write-only P10 Input Change Interrupt Disable 10 1 write-only P11 Input Change Interrupt Disable 11 1 write-only P12 Input Change Interrupt Disable 12 1 write-only P13 Input Change Interrupt Disable 13 1 write-only P14 Input Change Interrupt Disable 14 1 write-only P15 Input Change Interrupt Disable 15 1 write-only P16 Input Change Interrupt Disable 16 1 write-only P17 Input Change Interrupt Disable 17 1 write-only P18 Input Change Interrupt Disable 18 1 write-only P19 Input Change Interrupt Disable 19 1 write-only P20 Input Change Interrupt Disable 20 1 write-only P21 Input Change Interrupt Disable 21 1 write-only P22 Input Change Interrupt Disable 22 1 write-only P23 Input Change Interrupt Disable 23 1 write-only P24 Input Change Interrupt Disable 24 1 write-only P25 Input Change Interrupt Disable 25 1 write-only P26 Input Change Interrupt Disable 26 1 write-only P27 Input Change Interrupt Disable 27 1 write-only P28 Input Change Interrupt Disable 28 1 write-only P29 Input Change Interrupt Disable 29 1 write-only P30 Input Change Interrupt Disable 30 1 write-only P31 Input Change Interrupt Disable 31 1 write-only IMR Interrupt Mask Register 0x00000048 32 read-only 0x00000000 P0 Input Change Interrupt Mask 0 1 read-only P1 Input Change Interrupt Mask 1 1 read-only P2 Input Change Interrupt Mask 2 1 read-only P3 Input Change Interrupt Mask 3 1 read-only P4 Input Change Interrupt Mask 4 1 read-only P5 Input Change Interrupt Mask 5 1 read-only P6 Input Change Interrupt Mask 6 1 read-only P7 Input Change Interrupt Mask 7 1 read-only P8 Input Change Interrupt Mask 8 1 read-only P9 Input Change Interrupt Mask 9 1 read-only P10 Input Change Interrupt Mask 10 1 read-only P11 Input Change Interrupt Mask 11 1 read-only P12 Input Change Interrupt Mask 12 1 read-only P13 Input Change Interrupt Mask 13 1 read-only P14 Input Change Interrupt Mask 14 1 read-only P15 Input Change Interrupt Mask 15 1 read-only P16 Input Change Interrupt Mask 16 1 read-only P17 Input Change Interrupt Mask 17 1 read-only P18 Input Change Interrupt Mask 18 1 read-only P19 Input Change Interrupt Mask 19 1 read-only P20 Input Change Interrupt Mask 20 1 read-only P21 Input Change Interrupt Mask 21 1 read-only P22 Input Change Interrupt Mask 22 1 read-only P23 Input Change Interrupt Mask 23 1 read-only P24 Input Change Interrupt Mask 24 1 read-only P25 Input Change Interrupt Mask 25 1 read-only P26 Input Change Interrupt Mask 26 1 read-only P27 Input Change Interrupt Mask 27 1 read-only P28 Input Change Interrupt Mask 28 1 read-only P29 Input Change Interrupt Mask 29 1 read-only P30 Input Change Interrupt Mask 30 1 read-only P31 Input Change Interrupt Mask 31 1 read-only ISR Interrupt Status Register 0x0000004C 32 read-only 0x00000000 P0 Input Change Interrupt Status 0 1 read-only P1 Input Change Interrupt Status 1 1 read-only P2 Input Change Interrupt Status 2 1 read-only P3 Input Change Interrupt Status 3 1 read-only P4 Input Change Interrupt Status 4 1 read-only P5 Input Change Interrupt Status 5 1 read-only P6 Input Change Interrupt Status 6 1 read-only P7 Input Change Interrupt Status 7 1 read-only P8 Input Change Interrupt Status 8 1 read-only P9 Input Change Interrupt Status 9 1 read-only P10 Input Change Interrupt Status 10 1 read-only P11 Input Change Interrupt Status 11 1 read-only P12 Input Change Interrupt Status 12 1 read-only P13 Input Change Interrupt Status 13 1 read-only P14 Input Change Interrupt Status 14 1 read-only P15 Input Change Interrupt Status 15 1 read-only P16 Input Change Interrupt Status 16 1 read-only P17 Input Change Interrupt Status 17 1 read-only P18 Input Change Interrupt Status 18 1 read-only P19 Input Change Interrupt Status 19 1 read-only P20 Input Change Interrupt Status 20 1 read-only P21 Input Change Interrupt Status 21 1 read-only P22 Input Change Interrupt Status 22 1 read-only P23 Input Change Interrupt Status 23 1 read-only P24 Input Change Interrupt Status 24 1 read-only P25 Input Change Interrupt Status 25 1 read-only P26 Input Change Interrupt Status 26 1 read-only P27 Input Change Interrupt Status 27 1 read-only P28 Input Change Interrupt Status 28 1 read-only P29 Input Change Interrupt Status 29 1 read-only P30 Input Change Interrupt Status 30 1 read-only P31 Input Change Interrupt Status 31 1 read-only MDER Multi-driver Enable Register 0x00000050 32 write-only P0 Multi Drive Enable. 0 1 write-only P1 Multi Drive Enable. 1 1 write-only P2 Multi Drive Enable. 2 1 write-only P3 Multi Drive Enable. 3 1 write-only P4 Multi Drive Enable. 4 1 write-only P5 Multi Drive Enable. 5 1 write-only P6 Multi Drive Enable. 6 1 write-only P7 Multi Drive Enable. 7 1 write-only P8 Multi Drive Enable. 8 1 write-only P9 Multi Drive Enable. 9 1 write-only P10 Multi Drive Enable. 10 1 write-only P11 Multi Drive Enable. 11 1 write-only P12 Multi Drive Enable. 12 1 write-only P13 Multi Drive Enable. 13 1 write-only P14 Multi Drive Enable. 14 1 write-only P15 Multi Drive Enable. 15 1 write-only P16 Multi Drive Enable. 16 1 write-only P17 Multi Drive Enable. 17 1 write-only P18 Multi Drive Enable. 18 1 write-only P19 Multi Drive Enable. 19 1 write-only P20 Multi Drive Enable. 20 1 write-only P21 Multi Drive Enable. 21 1 write-only P22 Multi Drive Enable. 22 1 write-only P23 Multi Drive Enable. 23 1 write-only P24 Multi Drive Enable. 24 1 write-only P25 Multi Drive Enable. 25 1 write-only P26 Multi Drive Enable. 26 1 write-only P27 Multi Drive Enable. 27 1 write-only P28 Multi Drive Enable. 28 1 write-only P29 Multi Drive Enable. 29 1 write-only P30 Multi Drive Enable. 30 1 write-only P31 Multi Drive Enable. 31 1 write-only MDDR Multi-driver Disable Register 0x00000054 32 write-only P0 Multi Drive Disable. 0 1 write-only P1 Multi Drive Disable. 1 1 write-only P2 Multi Drive Disable. 2 1 write-only P3 Multi Drive Disable. 3 1 write-only P4 Multi Drive Disable. 4 1 write-only P5 Multi Drive Disable. 5 1 write-only P6 Multi Drive Disable. 6 1 write-only P7 Multi Drive Disable. 7 1 write-only P8 Multi Drive Disable. 8 1 write-only P9 Multi Drive Disable. 9 1 write-only P10 Multi Drive Disable. 10 1 write-only P11 Multi Drive Disable. 11 1 write-only P12 Multi Drive Disable. 12 1 write-only P13 Multi Drive Disable. 13 1 write-only P14 Multi Drive Disable. 14 1 write-only P15 Multi Drive Disable. 15 1 write-only P16 Multi Drive Disable. 16 1 write-only P17 Multi Drive Disable. 17 1 write-only P18 Multi Drive Disable. 18 1 write-only P19 Multi Drive Disable. 19 1 write-only P20 Multi Drive Disable. 20 1 write-only P21 Multi Drive Disable. 21 1 write-only P22 Multi Drive Disable. 22 1 write-only P23 Multi Drive Disable. 23 1 write-only P24 Multi Drive Disable. 24 1 write-only P25 Multi Drive Disable. 25 1 write-only P26 Multi Drive Disable. 26 1 write-only P27 Multi Drive Disable. 27 1 write-only P28 Multi Drive Disable. 28 1 write-only P29 Multi Drive Disable. 29 1 write-only P30 Multi Drive Disable. 30 1 write-only P31 Multi Drive Disable. 31 1 write-only MDSR Multi-driver Status Register 0x00000058 32 read-only 0x00000000 P0 Multi Drive Status. 0 1 read-only P1 Multi Drive Status. 1 1 read-only P2 Multi Drive Status. 2 1 read-only P3 Multi Drive Status. 3 1 read-only P4 Multi Drive Status. 4 1 read-only P5 Multi Drive Status. 5 1 read-only P6 Multi Drive Status. 6 1 read-only P7 Multi Drive Status. 7 1 read-only P8 Multi Drive Status. 8 1 read-only P9 Multi Drive Status. 9 1 read-only P10 Multi Drive Status. 10 1 read-only P11 Multi Drive Status. 11 1 read-only P12 Multi Drive Status. 12 1 read-only P13 Multi Drive Status. 13 1 read-only P14 Multi Drive Status. 14 1 read-only P15 Multi Drive Status. 15 1 read-only P16 Multi Drive Status. 16 1 read-only P17 Multi Drive Status. 17 1 read-only P18 Multi Drive Status. 18 1 read-only P19 Multi Drive Status. 19 1 read-only P20 Multi Drive Status. 20 1 read-only P21 Multi Drive Status. 21 1 read-only P22 Multi Drive Status. 22 1 read-only P23 Multi Drive Status. 23 1 read-only P24 Multi Drive Status. 24 1 read-only P25 Multi Drive Status. 25 1 read-only P26 Multi Drive Status. 26 1 read-only P27 Multi Drive Status. 27 1 read-only P28 Multi Drive Status. 28 1 read-only P29 Multi Drive Status. 29 1 read-only P30 Multi Drive Status. 30 1 read-only P31 Multi Drive Status. 31 1 read-only PUDR Pull-up Disable Register 0x00000060 32 write-only P0 Pull Up Disable. 0 1 write-only P1 Pull Up Disable. 1 1 write-only P2 Pull Up Disable. 2 1 write-only P3 Pull Up Disable. 3 1 write-only P4 Pull Up Disable. 4 1 write-only P5 Pull Up Disable. 5 1 write-only P6 Pull Up Disable. 6 1 write-only P7 Pull Up Disable. 7 1 write-only P8 Pull Up Disable. 8 1 write-only P9 Pull Up Disable. 9 1 write-only P10 Pull Up Disable. 10 1 write-only P11 Pull Up Disable. 11 1 write-only P12 Pull Up Disable. 12 1 write-only P13 Pull Up Disable. 13 1 write-only P14 Pull Up Disable. 14 1 write-only P15 Pull Up Disable. 15 1 write-only P16 Pull Up Disable. 16 1 write-only P17 Pull Up Disable. 17 1 write-only P18 Pull Up Disable. 18 1 write-only P19 Pull Up Disable. 19 1 write-only P20 Pull Up Disable. 20 1 write-only P21 Pull Up Disable. 21 1 write-only P22 Pull Up Disable. 22 1 write-only P23 Pull Up Disable. 23 1 write-only P24 Pull Up Disable. 24 1 write-only P25 Pull Up Disable. 25 1 write-only P26 Pull Up Disable. 26 1 write-only P27 Pull Up Disable. 27 1 write-only P28 Pull Up Disable. 28 1 write-only P29 Pull Up Disable. 29 1 write-only P30 Pull Up Disable. 30 1 write-only P31 Pull Up Disable. 31 1 write-only PUER Pull-up Enable Register 0x00000064 32 write-only P0 Pull Up Enable. 0 1 write-only P1 Pull Up Enable. 1 1 write-only P2 Pull Up Enable. 2 1 write-only P3 Pull Up Enable. 3 1 write-only P4 Pull Up Enable. 4 1 write-only P5 Pull Up Enable. 5 1 write-only P6 Pull Up Enable. 6 1 write-only P7 Pull Up Enable. 7 1 write-only P8 Pull Up Enable. 8 1 write-only P9 Pull Up Enable. 9 1 write-only P10 Pull Up Enable. 10 1 write-only P11 Pull Up Enable. 11 1 write-only P12 Pull Up Enable. 12 1 write-only P13 Pull Up Enable. 13 1 write-only P14 Pull Up Enable. 14 1 write-only P15 Pull Up Enable. 15 1 write-only P16 Pull Up Enable. 16 1 write-only P17 Pull Up Enable. 17 1 write-only P18 Pull Up Enable. 18 1 write-only P19 Pull Up Enable. 19 1 write-only P20 Pull Up Enable. 20 1 write-only P21 Pull Up Enable. 21 1 write-only P22 Pull Up Enable. 22 1 write-only P23 Pull Up Enable. 23 1 write-only P24 Pull Up Enable. 24 1 write-only P25 Pull Up Enable. 25 1 write-only P26 Pull Up Enable. 26 1 write-only P27 Pull Up Enable. 27 1 write-only P28 Pull Up Enable. 28 1 write-only P29 Pull Up Enable. 29 1 write-only P30 Pull Up Enable. 30 1 write-only P31 Pull Up Enable. 31 1 write-only PUSR Pad Pull-up Status Register 0x00000068 32 read-only 0x00000000 P0 Pull Up Status. 0 1 read-only P1 Pull Up Status. 1 1 read-only P2 Pull Up Status. 2 1 read-only P3 Pull Up Status. 3 1 read-only P4 Pull Up Status. 4 1 read-only P5 Pull Up Status. 5 1 read-only P6 Pull Up Status. 6 1 read-only P7 Pull Up Status. 7 1 read-only P8 Pull Up Status. 8 1 read-only P9 Pull Up Status. 9 1 read-only P10 Pull Up Status. 10 1 read-only P11 Pull Up Status. 11 1 read-only P12 Pull Up Status. 12 1 read-only P13 Pull Up Status. 13 1 read-only P14 Pull Up Status. 14 1 read-only P15 Pull Up Status. 15 1 read-only P16 Pull Up Status. 16 1 read-only P17 Pull Up Status. 17 1 read-only P18 Pull Up Status. 18 1 read-only P19 Pull Up Status. 19 1 read-only P20 Pull Up Status. 20 1 read-only P21 Pull Up Status. 21 1 read-only P22 Pull Up Status. 22 1 read-only P23 Pull Up Status. 23 1 read-only P24 Pull Up Status. 24 1 read-only P25 Pull Up Status. 25 1 read-only P26 Pull Up Status. 26 1 read-only P27 Pull Up Status. 27 1 read-only P28 Pull Up Status. 28 1 read-only P29 Pull Up Status. 29 1 read-only P30 Pull Up Status. 30 1 read-only P31 Pull Up Status. 31 1 read-only ASR Peripheral A Select Register 0x00000070 32 write-only P0 Peripheral A Select. 0 1 write-only P1 Peripheral A Select. 1 1 write-only P2 Peripheral A Select. 2 1 write-only P3 Peripheral A Select. 3 1 write-only P4 Peripheral A Select. 4 1 write-only P5 Peripheral A Select. 5 1 write-only P6 Peripheral A Select. 6 1 write-only P7 Peripheral A Select. 7 1 write-only P8 Peripheral A Select. 8 1 write-only P9 Peripheral A Select. 9 1 write-only P10 Peripheral A Select. 10 1 write-only P11 Peripheral A Select. 11 1 write-only P12 Peripheral A Select. 12 1 write-only P13 Peripheral A Select. 13 1 write-only P14 Peripheral A Select. 14 1 write-only P15 Peripheral A Select. 15 1 write-only P16 Peripheral A Select. 16 1 write-only P17 Peripheral A Select. 17 1 write-only P18 Peripheral A Select. 18 1 write-only P19 Peripheral A Select. 19 1 write-only P20 Peripheral A Select. 20 1 write-only P21 Peripheral A Select. 21 1 write-only P22 Peripheral A Select. 22 1 write-only P23 Peripheral A Select. 23 1 write-only P24 Peripheral A Select. 24 1 write-only P25 Peripheral A Select. 25 1 write-only P26 Peripheral A Select. 26 1 write-only P27 Peripheral A Select. 27 1 write-only P28 Peripheral A Select. 28 1 write-only P29 Peripheral A Select. 29 1 write-only P30 Peripheral A Select. 30 1 write-only P31 Peripheral A Select. 31 1 write-only BSR Peripheral B Select Register 0x00000074 32 write-only P0 Peripheral B Select. 0 1 write-only P1 Peripheral B Select. 1 1 write-only P2 Peripheral B Select. 2 1 write-only P3 Peripheral B Select. 3 1 write-only P4 Peripheral B Select. 4 1 write-only P5 Peripheral B Select. 5 1 write-only P6 Peripheral B Select. 6 1 write-only P7 Peripheral B Select. 7 1 write-only P8 Peripheral B Select. 8 1 write-only P9 Peripheral B Select. 9 1 write-only P10 Peripheral B Select. 10 1 write-only P11 Peripheral B Select. 11 1 write-only P12 Peripheral B Select. 12 1 write-only P13 Peripheral B Select. 13 1 write-only P14 Peripheral B Select. 14 1 write-only P15 Peripheral B Select. 15 1 write-only P16 Peripheral B Select. 16 1 write-only P17 Peripheral B Select. 17 1 write-only P18 Peripheral B Select. 18 1 write-only P19 Peripheral B Select. 19 1 write-only P20 Peripheral B Select. 20 1 write-only P21 Peripheral B Select. 21 1 write-only P22 Peripheral B Select. 22 1 write-only P23 Peripheral B Select. 23 1 write-only P24 Peripheral B Select. 24 1 write-only P25 Peripheral B Select. 25 1 write-only P26 Peripheral B Select. 26 1 write-only P27 Peripheral B Select. 27 1 write-only P28 Peripheral B Select. 28 1 write-only P29 Peripheral B Select. 29 1 write-only P30 Peripheral B Select. 30 1 write-only P31 Peripheral B Select. 31 1 write-only ABSR AB Status Register 0x00000078 32 read-only 0x00000000 P0 Peripheral A B Status. 0 1 read-only P1 Peripheral A B Status. 1 1 read-only P2 Peripheral A B Status. 2 1 read-only P3 Peripheral A B Status. 3 1 read-only P4 Peripheral A B Status. 4 1 read-only P5 Peripheral A B Status. 5 1 read-only P6 Peripheral A B Status. 6 1 read-only P7 Peripheral A B Status. 7 1 read-only P8 Peripheral A B Status. 8 1 read-only P9 Peripheral A B Status. 9 1 read-only P10 Peripheral A B Status. 10 1 read-only P11 Peripheral A B Status. 11 1 read-only P12 Peripheral A B Status. 12 1 read-only P13 Peripheral A B Status. 13 1 read-only P14 Peripheral A B Status. 14 1 read-only P15 Peripheral A B Status. 15 1 read-only P16 Peripheral A B Status. 16 1 read-only P17 Peripheral A B Status. 17 1 read-only P18 Peripheral A B Status. 18 1 read-only P19 Peripheral A B Status. 19 1 read-only P20 Peripheral A B Status. 20 1 read-only P21 Peripheral A B Status. 21 1 read-only P22 Peripheral A B Status. 22 1 read-only P23 Peripheral A B Status. 23 1 read-only P24 Peripheral A B Status. 24 1 read-only P25 Peripheral A B Status. 25 1 read-only P26 Peripheral A B Status. 26 1 read-only P27 Peripheral A B Status. 27 1 read-only P28 Peripheral A B Status. 28 1 read-only P29 Peripheral A B Status. 29 1 read-only P30 Peripheral A B Status. 30 1 read-only P31 Peripheral A B Status. 31 1 read-only OWER Output Write Enable 0x000000A0 32 write-only P0 Output Write Enable. 0 1 write-only P1 Output Write Enable. 1 1 write-only P2 Output Write Enable. 2 1 write-only P3 Output Write Enable. 3 1 write-only P4 Output Write Enable. 4 1 write-only P5 Output Write Enable. 5 1 write-only P6 Output Write Enable. 6 1 write-only P7 Output Write Enable. 7 1 write-only P8 Output Write Enable. 8 1 write-only P9 Output Write Enable. 9 1 write-only P10 Output Write Enable. 10 1 write-only P11 Output Write Enable. 11 1 write-only P12 Output Write Enable. 12 1 write-only P13 Output Write Enable. 13 1 write-only P14 Output Write Enable. 14 1 write-only P15 Output Write Enable. 15 1 write-only P16 Output Write Enable. 16 1 write-only P17 Output Write Enable. 17 1 write-only P18 Output Write Enable. 18 1 write-only P19 Output Write Enable. 19 1 write-only P20 Output Write Enable. 20 1 write-only P21 Output Write Enable. 21 1 write-only P22 Output Write Enable. 22 1 write-only P23 Output Write Enable. 23 1 write-only P24 Output Write Enable. 24 1 write-only P25 Output Write Enable. 25 1 write-only P26 Output Write Enable. 26 1 write-only P27 Output Write Enable. 27 1 write-only P28 Output Write Enable. 28 1 write-only P29 Output Write Enable. 29 1 write-only P30 Output Write Enable. 30 1 write-only P31 Output Write Enable. 31 1 write-only OWDR Output Write Disable 0x000000A4 32 write-only P0 Output Write Disable. 0 1 write-only P1 Output Write Disable. 1 1 write-only P2 Output Write Disable. 2 1 write-only P3 Output Write Disable. 3 1 write-only P4 Output Write Disable. 4 1 write-only P5 Output Write Disable. 5 1 write-only P6 Output Write Disable. 6 1 write-only P7 Output Write Disable. 7 1 write-only P8 Output Write Disable. 8 1 write-only P9 Output Write Disable. 9 1 write-only P10 Output Write Disable. 10 1 write-only P11 Output Write Disable. 11 1 write-only P12 Output Write Disable. 12 1 write-only P13 Output Write Disable. 13 1 write-only P14 Output Write Disable. 14 1 write-only P15 Output Write Disable. 15 1 write-only P16 Output Write Disable. 16 1 write-only P17 Output Write Disable. 17 1 write-only P18 Output Write Disable. 18 1 write-only P19 Output Write Disable. 19 1 write-only P20 Output Write Disable. 20 1 write-only P21 Output Write Disable. 21 1 write-only P22 Output Write Disable. 22 1 write-only P23 Output Write Disable. 23 1 write-only P24 Output Write Disable. 24 1 write-only P25 Output Write Disable. 25 1 write-only P26 Output Write Disable. 26 1 write-only P27 Output Write Disable. 27 1 write-only P28 Output Write Disable. 28 1 write-only P29 Output Write Disable. 29 1 write-only P30 Output Write Disable. 30 1 write-only P31 Output Write Disable. 31 1 write-only OWSR Output Write Status Register 0x000000A8 32 read-only 0x00000000 P0 Output Write Status. 0 1 read-only P1 Output Write Status. 1 1 read-only P2 Output Write Status. 2 1 read-only P3 Output Write Status. 3 1 read-only P4 Output Write Status. 4 1 read-only P5 Output Write Status. 5 1 read-only P6 Output Write Status. 6 1 read-only P7 Output Write Status. 7 1 read-only P8 Output Write Status. 8 1 read-only P9 Output Write Status. 9 1 read-only P10 Output Write Status. 10 1 read-only P11 Output Write Status. 11 1 read-only P12 Output Write Status. 12 1 read-only P13 Output Write Status. 13 1 read-only P14 Output Write Status. 14 1 read-only P15 Output Write Status. 15 1 read-only P16 Output Write Status. 16 1 read-only P17 Output Write Status. 17 1 read-only P18 Output Write Status. 18 1 read-only P19 Output Write Status. 19 1 read-only P20 Output Write Status. 20 1 read-only P21 Output Write Status. 21 1 read-only P22 Output Write Status. 22 1 read-only P23 Output Write Status. 23 1 read-only P24 Output Write Status. 24 1 read-only P25 Output Write Status. 25 1 read-only P26 Output Write Status. 26 1 read-only P27 Output Write Status. 27 1 read-only P28 Output Write Status. 28 1 read-only P29 Output Write Status. 29 1 read-only P30 Output Write Status. 30 1 read-only P31 Output Write Status. 31 1 read-only PMC 6347A Power Management Controller 0xFFFFFC00 0 0x200 registers PMC_SCER System Clock Enable Register 0x00000000 32 write-only UHP USB Host Port Clock Enable 6 1 write-only UDP USB Device Port Clock Enable 7 1 write-only PCK0 Programmable Clock 0 Output Enable 8 1 write-only PCK1 Programmable Clock 1 Output Enable 9 1 write-only PMC_SCDR System Clock Disable Register 0x00000004 32 write-only PCK Processor Clock Disable 0 1 write-only UHP USB Host Port Clock Disable 6 1 write-only UDP USB Device Port Clock Disable 7 1 write-only PCK0 Programmable Clock 0 Output Disable 8 1 write-only PCK1 Programmable Clock 1 Output Disable 9 1 write-only PMC_SCSR System Clock Status Register 0x00000008 32 read-only 0x00000003 PCK Processor Clock Status 0 1 read-only UHP USB Host Port Clock Status 6 1 read-only UDP USB Device Port Clock Status 7 1 read-only PCK0 Programmable Clock 0 Output Status 8 1 read-only PCK1 Programmable Clock 1 Output Status 9 1 read-only PMC_PCER Peripheral Clock Enable Register 0x00000010 32 write-only PID2 Peripheral Clock 2 Enable 2 1 write-only PID3 Peripheral Clock 3 Enable 3 1 write-only PID4 Peripheral Clock 4 Enable 4 1 write-only PID5 Peripheral Clock 5 Enable 5 1 write-only PID6 Peripheral Clock 6 Enable 6 1 write-only PID7 Peripheral Clock 7 Enable 7 1 write-only PID8 Peripheral Clock 8 Enable 8 1 write-only PID9 Peripheral Clock 9 Enable 9 1 write-only PID10 Peripheral Clock 10 Enable 10 1 write-only PID11 Peripheral Clock 11 Enable 11 1 write-only PID12 Peripheral Clock 12 Enable 12 1 write-only PID13 Peripheral Clock 13 Enable 13 1 write-only PID14 Peripheral Clock 14 Enable 14 1 write-only PID15 Peripheral Clock 15 Enable 15 1 write-only PID16 Peripheral Clock 16 Enable 16 1 write-only PID17 Peripheral Clock 17 Enable 17 1 write-only PID18 Peripheral Clock 18 Enable 18 1 write-only PID19 Peripheral Clock 19 Enable 19 1 write-only PID20 Peripheral Clock 20 Enable 20 1 write-only PID21 Peripheral Clock 21 Enable 21 1 write-only PID22 Peripheral Clock 22 Enable 22 1 write-only PID23 Peripheral Clock 23 Enable 23 1 write-only PID24 Peripheral Clock 24 Enable 24 1 write-only PID25 Peripheral Clock 25 Enable 25 1 write-only PID26 Peripheral Clock 26 Enable 26 1 write-only PID27 Peripheral Clock 27 Enable 27 1 write-only PID28 Peripheral Clock 28 Enable 28 1 write-only PID29 Peripheral Clock 29 Enable 29 1 write-only PID30 Peripheral Clock 30 Enable 30 1 write-only PID31 Peripheral Clock 31 Enable 31 1 write-only PMC_PCDR Peripheral Clock Disable Register 0x00000014 32 write-only PID2 Peripheral Clock 2 Disable 2 1 write-only PID3 Peripheral Clock 3 Disable 3 1 write-only PID4 Peripheral Clock 4 Disable 4 1 write-only PID5 Peripheral Clock 5 Disable 5 1 write-only PID6 Peripheral Clock 6 Disable 6 1 write-only PID7 Peripheral Clock 7 Disable 7 1 write-only PID8 Peripheral Clock 8 Disable 8 1 write-only PID9 Peripheral Clock 9 Disable 9 1 write-only PID10 Peripheral Clock 10 Disable 10 1 write-only PID11 Peripheral Clock 11 Disable 11 1 write-only PID12 Peripheral Clock 12 Disable 12 1 write-only PID13 Peripheral Clock 13 Disable 13 1 write-only PID14 Peripheral Clock 14 Disable 14 1 write-only PID15 Peripheral Clock 15 Disable 15 1 write-only PID16 Peripheral Clock 16 Disable 16 1 write-only PID17 Peripheral Clock 17 Disable 17 1 write-only PID18 Peripheral Clock 18 Disable 18 1 write-only PID19 Peripheral Clock 19 Disable 19 1 write-only PID20 Peripheral Clock 20 Disable 20 1 write-only PID21 Peripheral Clock 21 Disable 21 1 write-only PID22 Peripheral Clock 22 Disable 22 1 write-only PID23 Peripheral Clock 23 Disable 23 1 write-only PID24 Peripheral Clock 24 Disable 24 1 write-only PID25 Peripheral Clock 25 Disable 25 1 write-only PID26 Peripheral Clock 26 Disable 26 1 write-only PID27 Peripheral Clock 27 Disable 27 1 write-only PID28 Peripheral Clock 28 Disable 28 1 write-only PID29 Peripheral Clock 29 Disable 29 1 write-only PID30 Peripheral Clock 30 Disable 30 1 write-only PID31 Peripheral Clock 31 Disable 31 1 write-only PMC_PCSR Peripheral Clock Status Register 0x00000018 32 read-only 0x00000000 PID2 Peripheral Clock 2 Status 2 1 read-only PID3 Peripheral Clock 3 Status 3 1 read-only PID4 Peripheral Clock 4 Status 4 1 read-only PID5 Peripheral Clock 5 Status 5 1 read-only PID6 Peripheral Clock 6 Status 6 1 read-only PID7 Peripheral Clock 7 Status 7 1 read-only PID8 Peripheral Clock 8 Status 8 1 read-only PID9 Peripheral Clock 9 Status 9 1 read-only PID10 Peripheral Clock 10 Status 10 1 read-only PID11 Peripheral Clock 11 Status 11 1 read-only PID12 Peripheral Clock 12 Status 12 1 read-only PID13 Peripheral Clock 13 Status 13 1 read-only PID14 Peripheral Clock 14 Status 14 1 read-only PID15 Peripheral Clock 15 Status 15 1 read-only PID16 Peripheral Clock 16 Status 16 1 read-only PID17 Peripheral Clock 17 Status 17 1 read-only PID18 Peripheral Clock 18 Status 18 1 read-only PID19 Peripheral Clock 19 Status 19 1 read-only PID20 Peripheral Clock 20 Status 20 1 read-only PID21 Peripheral Clock 21 Status 21 1 read-only PID22 Peripheral Clock 22 Status 22 1 read-only PID23 Peripheral Clock 23 Status 23 1 read-only PID24 Peripheral Clock 24 Status 24 1 read-only PID25 Peripheral Clock 25 Status 25 1 read-only PID26 Peripheral Clock 26 Status 26 1 read-only PID27 Peripheral Clock 27 Status 27 1 read-only PID28 Peripheral Clock 28 Status 28 1 read-only PID29 Peripheral Clock 29 Status 29 1 read-only PID30 Peripheral Clock 30 Status 30 1 read-only PID31 Peripheral Clock 31 Status 31 1 read-only CKGR_MOR Main Oscillator Register 0x00000020 32 read-write 0x00000000 MOSCEN Main Oscillator Enable 0 1 read-write OSCBYPASS Oscillator Bypass 1 1 read-write OSCOUNT Main Oscillator Start-up Time 8 8 read-write CKGR_MCFR Main Clock Frequency Register 0x00000024 32 read-only 0x00000000 MAINF Main Clock Frequency 0 16 read-only MAINRDY Main Clock Ready 16 1 read-only CKGR_PLLAR PLL A Register 0x00000028 32 read-write 0x00003F00 DIVA Divider A 0 8 read-write PLLACOUNT PLL A Counter 8 6 read-write OUTA PLL A Clock Frequency Range 14 2 read-write MULA PLL A Multiplier 16 8 read-write STUCKTO1 29 1 read-write CKGR_PLLBR PLL B Register 0x0000002C 32 read-write 0x00003F00 DIVB Divider B 0 8 read-write PLLBCOUNT PLL B Counter 8 6 read-write OUTB PLL B Clock Frequency Range 14 2 read-write MULB PLL B Multiplier 16 6 read-write USBDIV Divider for USB Clock. 28 2 read-write PMC_MCKR Master Clock Register 0x00000030 32 read-write 0x00000000 CSS Master/Processor Clock Source Selection 0 2 read-write PRES Master/Processor Clock Prescaler 2 3 read-write MDIV Master Clock Division 8 2 read-write PDIV Processor Clock Division 12 1 read-write 2 4 0-1 PMC_PCK[%s] Programmable Clock 0 Register 0x00000040 32 read-write CSS Master Clock Selection 0 2 read-write PRES Programmable Clock Prescaler 2 3 read-write PMC_IER Interrupt Enable Register 0x00000060 32 write-only MOSCS Main Oscillator Status Interrupt Enable 0 1 write-only LOCKA PLL A Lock Interrupt Enable 1 1 write-only LOCKB PLL B Lock Interrupt Enable 2 1 write-only MCKRDY Master Clock Ready Interrupt Enable 3 1 write-only PCKRDY0 Programmable Clock Ready 0 Interrupt Enable 8 1 write-only PCKRDY1 Programmable Clock Ready 1 Interrupt Enable 9 1 write-only PMC_IDR Interrupt Disable Register 0x00000064 32 write-only MOSCS Main Oscillator Status Interrupt Disable 0 1 write-only LOCKA PLL A Lock Interrupt Disable 1 1 write-only LOCKB PLL B Lock Interrupt Disable 2 1 write-only MCKRDY Master Clock Ready Interrupt Disable 3 1 write-only PCKRDY0 Programmable Clock Ready 0 Interrupt Disable 8 1 write-only PCKRDY1 Programmable Clock Ready 1 Interrupt Disable 9 1 write-only PMC_SR Status Register 0x00000068 32 read-only 0x00000008 MOSCS Main Oscillator Status 0 1 read-only LOCKA PLL A Lock Status 1 1 read-only LOCKB PLL B Lock Status 2 1 read-only MCKRDY Master Clock Status 3 1 read-only OSC_SEL Slow Clock Oscillator Selection 7 1 read-only PCKRDY0 Programmable Clock Ready Status 8 1 read-only PCKRDY1 Programmable Clock Ready Status 9 1 read-only PMC_IMR Interrupt Mask Register 0x0000006C 32 read-only 0x00000000 MOSCS Main Oscillator Status Interrupt Mask 0 1 read-only LOCKA PLL A Lock Interrupt Mask 1 1 read-only LOCKB PLL B Lock Interrupt Mask 2 1 read-only MCKRDY Master Clock Ready Interrupt Mask 3 1 read-only PCKRDY0 Programmable Clock Ready Interrupt Mask 8 1 read-only PCKRDY1 Programmable Clock Ready Interrupt Mask 9 1 read-only PMC_PLLICPR PLL Charge Pump Current Register 0x00000080 32 write-only 0x00000000 ICPLLA Charge Pump Current 0 1 write-only ICPLLB Charge Pump Current 16 1 write-only RSTC 6098J Reset Controller SYSC RSTC_ 0xFFFFFD00 0 0x200 registers CR Control Register 0x00000000 32 write-only PROCRST Processor Reset 0 1 write-only PERRST Peripheral Reset 2 1 write-only EXTRST External Reset 3 1 write-only KEY Password 24 8 write-only SR Status Register 0x00000004 32 read-only 0x00000000 URSTS User Reset Status 0 1 read-only RSTTYP Reset Type 8 3 read-only NRSTL NRST Pin Level 16 1 read-only SRCMP Software Reset Command in Progress 17 1 read-only MR Mode Register 0x00000008 32 read-write 0x00000000 ERSTL External Reset Length 8 4 read-write KEY Password 24 8 read-write SHDWC 6122J Shutdown Controller SYSC SHDWC_ 0xFFFFFD10 0 0x200 registers CR Shutdown Control Register 0x00000000 32 write-only SHDW Shutdown Command 0 1 write-only KEY Password 24 8 write-only MR Shutdown Mode Register 0x00000004 32 read-write 0x00000303 WKMODE0 Wake-up Mode 0 0 2 read-write CPTWK0 Counter on Wake-up 0 4 4 read-write RTTWKEN Real-time Timer Wake-up Enable 16 1 read-write SR Shutdown Status Register 0x00000008 32 read-only 0x00000000 WAKEUP0 Wake-up 0 Status 0 1 read-only RTTWK Real-time Timer Wake-up 16 1 read-only RTT 6081C Real-time Timer SYSC RTT_ 0xFFFFFD20 0 0x200 registers MR Mode Register 0x00000000 32 read-write 0x00008000 RTPRES Real-time Timer Prescaler Value 0 16 read-write ALMIEN Alarm Interrupt Enable 16 1 read-write RTTINCIEN Real-time Timer Increment Interrupt Enable 17 1 read-write RTTRST Real-time Timer Restart 18 1 read-write AR Alarm Register 0x00000004 32 read-write 0xFFFFFFFF ALMV Alarm Value 0 32 read-write VR Value Register 0x00000008 32 read-only 0x00000000 CRTV Current Real-time Value 0 32 read-only SR Status Register 0x0000000C 32 read-only 0x00000000 ALMS Real-time Alarm Status 0 1 read-only RTTINC Real-time Timer Increment 1 1 read-only PIT 6079B Periodic Interval Timer SYSC PIT_ 0xFFFFFD30 0 0x200 registers MR Mode Register 0x00000000 32 read-write 0x000FFFFF PIV Periodic Interval Value 0 20 read-write PITEN Period Interval Timer Enabled 24 1 read-write PITIEN Periodic Interval Timer Interrupt Enable 25 1 read-write SR Status Register 0x00000004 32 read-only 0x00000000 PITS Periodic Interval Timer Status 0 1 read-only PIVR Periodic Interval Value Register 0x00000008 32 read-only 0x00000000 CPIV Current Periodic Interval Value 0 20 read-only PICNT Periodic Interval Counter 20 12 read-only PIIR Periodic Interval Image Register 0x0000000C 32 read-only 0x00000000 CPIV Current Periodic Interval Value 0 20 read-only PICNT Periodic Interval Counter 20 12 read-only WDT 6080C Watchdog Timer SYSC WDT_ 0xFFFFFD40 0 0x200 registers CR Control Register 0x00000000 32 write-only WDRSTT Watchdog Restart 0 1 write-only KEY Password 24 8 write-only MR Mode Register 0x00000004 32 read-write 0x3FFF2FFF WDV Watchdog Counter Value 0 12 read-write WDFIEN Watchdog Fault Interrupt Enable 12 1 read-write WDRSTEN Watchdog Reset Enable 13 1 read-write WDRPROC Watchdog Reset Processor 14 1 read-write WDDIS Watchdog Disable 15 1 read-write WDD Watchdog Delta Value 16 12 read-write WDDBGHLT Watchdog Debug Halt 28 1 read-write WDIDLEHLT Watchdog Idle Halt 29 1 read-write SR Status Register 0x00000008 32 read-only 0x00000000 WDUNF Watchdog Underflow 0 1 read-only WDERR Watchdog Error 1 1 read-only GPBR 6378D General Purpose Backup Register SYSC GPBR_ 0xFFFFFD50 0 0x200 registers 4 4 0-3 GPBR[%s] General Purpose Backup Register 0x00000000 32 read-write GPBR_VALUE Value of GPBR x 0 32 read-write