Freescale Semiconductor, Inc. Freescale Kinetis_L MKL36Z4 1.6 MKL36Z4 Freescale Microcontroller Redistribution and use in source and binary forms, with or without modification,\nare permitted provided that the following conditions are met:\n o Redistributions of source code must retain the above copyright notice, this list\n of conditions and the following disclaimer.\n o Redistributions in binary form must reproduce the above copyright notice, this\n list of conditions and the following disclaimer in the documentation and/or\n other materials provided with the distribution.\n o Neither the name of Freescale Semiconductor, Inc. nor the names of its\n contributors may be used to endorse or promote products derived from this\n software without specific prior written permission.\n THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND\n ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED\n WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE\n DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR\n ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES\n (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;\n LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON\n ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT\n (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS\n SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. CM0PLUS r0p0 little false false true 2 false 8 32 FTFA_FlashConfig Flash configuration field NV_ 0x400 0 0xE registers BACKKEY3 Backdoor Comparison Key 3. 0 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only BACKKEY2 Backdoor Comparison Key 2. 0x1 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only BACKKEY1 Backdoor Comparison Key 1. 0x2 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only BACKKEY0 Backdoor Comparison Key 0. 0x3 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only BACKKEY7 Backdoor Comparison Key 7. 0x4 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only BACKKEY6 Backdoor Comparison Key 6. 0x5 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only BACKKEY5 Backdoor Comparison Key 5. 0x6 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only BACKKEY4 Backdoor Comparison Key 4. 0x7 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only FPROT3 Non-volatile P-Flash Protection 1 - Low Register 0x8 8 read-only 0xFF 0xFF PROT P-Flash Region Protect 0 8 read-only FPROT2 Non-volatile P-Flash Protection 1 - High Register 0x9 8 read-only 0xFF 0xFF PROT P-Flash Region Protect 0 8 read-only FPROT1 Non-volatile P-Flash Protection 0 - Low Register 0xA 8 read-only 0xFF 0xFF PROT P-Flash Region Protect 0 8 read-only FPROT0 Non-volatile P-Flash Protection 0 - High Register 0xB 8 read-only 0xFF 0xFF PROT P-Flash Region Protect 0 8 read-only FSEC Non-volatile Flash Security Register 0xC 8 read-only 0xFF 0xFF SEC Flash Security 0 2 read-only 10 MCU security status is unsecure #10 11 MCU security status is secure #11 FSLACC Freescale Failure Analysis Access Code 2 2 read-only 10 Freescale factory access denied #10 11 Freescale factory access granted #11 MEEN no description available 4 2 read-only 10 Mass erase is disabled #10 11 Mass erase is enabled #11 KEYEN Backdoor Key Security Enable 6 2 read-only 10 Backdoor key access enabled #10 11 Backdoor key access disabled #11 FOPT Non-volatile Flash Option Register 0xD 8 read-only 0xFF 0xFF LPBOOT0 no description available 0 1 read-only 00 Core and system clock divider (OUTDIV1) is 0x7 (divide by 8) when LPBOOT1=0 or 0x1 (divide by 2) when LPBOOT1=1. #0 01 Core and system clock divider (OUTDIV1) is 0x3 (divide by 4) when LPBOOT1=0 or 0x0 (divide by 1) when LPBOOT1=1. #1 NMI_DIS no description available 2 1 read-only 00 NMI interrupts are always blocked #0 01 NMI_b pin/interrupts reset default to enabled #1 RESET_PIN_CFG no description available 3 1 read-only 00 RESET pin is disabled following a POR and cannot be enabled as reset function #0 01 RESET_b pin is dedicated #1 LPBOOT1 no description available 4 1 read-only 00 Core and system clock divider (OUTDIV1) is 0x7 (divide by 8) when LPBOOT0=0 or 0x3 (divide by 4) when LPBOOT0=1. #0 01 Core and system clock divider (OUTDIV1) is 0x1 (divide by 2) when LPBOOT0=0 or 0x0 (divide by 1) when LPBOOT0=1. #1 FAST_INIT no description available 5 1 read-only 00 Slower initialization #0 01 Fast Initialization #1 DMA DMA Controller DMA_ 0x40008000 0x100 0x40 registers DMA0 0 DMA1 1 DMA2 2 DMA3 3 SAR0 Source Address Register 0x100 32 read-write 0 0xFFFFFFFF SAR Each SAR contains the byte address used by the DMA controller to read data 0 32 read-write DAR0 Destination Address Register 0x104 32 read-write 0 0xFFFFFFFF DAR Each DAR contains the byte address used by the DMA controller to write data 0 32 read-write DSR_BCR0 DMA Status Register / Byte Count Register 0x108 32 read-write 0 0xFFFFFFFF BCR This field contains the number of bytes yet to be transferred for a given block 0 24 read-write DONE Transactions Done 24 1 read-write 0 DMA transfer is not yet complete. Writing a 0 has no effect. #0 1 DMA transfer completed. Writing a 1 to this bit clears all DMA status bits and should be used in an interrupt service routine to clear the DMA interrupt and error bits. #1 BSY Busy 25 1 read-only 0 DMA channel is inactive. Cleared when the DMA has finished the last transaction. #0 1 BSY is set the first time the channel is enabled after a transfer is initiated. #1 REQ Request 26 1 read-only 0 No request is pending or the channel is currently active. Cleared when the channel is selected. #0 1 The DMA channel has a transfer remaining and the channel is not selected. #1 BED Bus Error on Destination 28 1 read-only 0 No bus error occurred. #0 1 The DMA channel terminated with a bus error during the write portion of a transfer. #1 BES Bus Error on Source 29 1 read-only 0 No bus error occurred. #0 1 The DMA channel terminated with a bus error during the read portion of a transfer. #1 CE Configuration Error 30 1 read-only 0 No configuration error exists. #0 1 A configuration error has occurred. #1 DSR0 DMA_DSR0 register. 0x10B 8 read-write 0 0xFF DCR0 DMA Control Register 0x10C 32 read-write 0 0xFFFFFFFF LCH2 Link Channel 2 0 2 read-write 00 DMA Channel 0 #00 01 DMA Channel 1 #01 10 DMA Channel 2 #10 11 DMA Channel 3 #11 LCH1 Link Channel 1 2 2 read-write 00 DMA Channel 0 #00 01 DMA Channel 1 #01 10 DMA Channel 2 #10 11 DMA Channel 3 #11 LINKCC Link Channel Control 4 2 read-write 00 No channel-to-channel linking #00 01 Perform a link to channel LCH1 after each cycle-steal transfer followed by a link to LCH2 after the BCR decrements to 0. #01 10 Perform a link to channel LCH1 after each cycle-steal transfer #10 11 Perform a link to channel LCH1 after the BCR decrements to 0. #11 D_REQ Disable Request 7 1 read-write 0 ERQ bit is not affected. #0 1 ERQ bit is cleared when the BCR is exhausted. #1 DMOD Destination Address Modulo 8 4 read-write 0000 Buffer disabled #0000 0001 Circular buffer size is 16 bytes #0001 0010 Circular buffer size is 32 bytes #0010 0011 Circular buffer size is 64 bytes #0011 0100 Circular buffer size is 128 bytes #0100 0101 Circular buffer size is 256 bytes #0101 0110 Circular buffer size is 512 bytes #0110 0111 Circular buffer size is 1 KB #0111 1000 Circular buffer size is 2 KB #1000 1001 Circular buffer size is 4 KB #1001 1010 Circular buffer size is 8 KB #1010 1011 Circular buffer size is 16 KB #1011 1100 Circular buffer size is 32 KB #1100 1101 Circular buffer size is 64 KB #1101 1110 Circular buffer size is 128 KB #1110 1111 Circular buffer size is 256 KB #1111 SMOD Source Address Modulo 12 4 read-write 0000 Buffer disabled #0000 0001 Circular buffer size is 16 bytes. #0001 0010 Circular buffer size is 32 bytes. #0010 0011 Circular buffer size is 64 bytes. #0011 0100 Circular buffer size is 128 bytes. #0100 0101 Circular buffer size is 256 bytes. #0101 0110 Circular buffer size is 512 bytes. #0110 0111 Circular buffer size is 1 KB. #0111 1000 Circular buffer size is 2 KB. #1000 1001 Circular buffer size is 4 KB. #1001 1010 Circular buffer size is 8 KB. #1010 1011 Circular buffer size is 16 KB. #1011 1100 Circular buffer size is 32 KB. #1100 1101 Circular buffer size is 64 KB. #1101 1110 Circular buffer size is 128 KB. #1110 1111 Circular buffer size is 256 KB. #1111 START Start Transfer 16 1 write-only 0 DMA inactive #0 1 The DMA begins the transfer in accordance to the values in the TCDn. START is cleared automatically after one module clock and always reads as logic 0. #1 DSIZE Destination Size 17 2 read-write 00 32-bit #00 01 8-bit #01 10 16-bit #10 11 Reserved (generates a configuration error (DSRn[CE]) if incorrectly specified at time of channel activation) #11 DINC Destination Increment 19 1 read-write 0 No change to the DAR after a successful transfer. #0 1 The DAR increments by 1, 2, 4 depending upon the size of the transfer. #1 SSIZE Source Size 20 2 read-write 00 32-bit #00 01 8-bit #01 10 16-bit #10 11 Reserved (generates a configuration error (DSRn[CE]) if incorrectly specified at time of channel activation) #11 SINC Source Increment 22 1 read-write 0 No change to SAR after a successful transfer. #0 1 The SAR increments by 1, 2, 4 as determined by the transfer size. #1 EADREQ Enable asynchronous DMA requests 23 1 read-write 0 Disabled #0 1 Enabled #1 AA Auto-align 28 1 read-write 0 Auto-align disabled #0 1 If SSIZE indicates a transfer no smaller than DSIZE, source accesses are auto-aligned; otherwise, destination accesses are auto-aligned. Source alignment takes precedence over destination alignment. If auto-alignment is enabled, the appropriate address register increments, regardless of DINC or SINC. #1 CS Cycle Steal 29 1 read-write 0 DMA continuously makes read/write transfers until the BCR decrements to 0. #0 1 Forces a single read/write transfer per request. #1 ERQ Enable Peripheral Request 30 1 read-write 0 Peripheral request is ignored. #0 1 Enables peripheral request to initiate transfer. A software-initiated request (setting START) is always enabled. #1 EINT Enable Interrupt on Completion of Transfer 31 1 read-write 0 No interrupt is generated. #0 1 Interrupt signal is enabled. #1 SAR1 Source Address Register 0x110 32 read-write 0 0xFFFFFFFF SAR Each SAR contains the byte address used by the DMA controller to read data 0 32 read-write DAR1 Destination Address Register 0x114 32 read-write 0 0xFFFFFFFF DAR Each DAR contains the byte address used by the DMA controller to write data 0 32 read-write DSR_BCR1 DMA Status Register / Byte Count Register 0x118 32 read-write 0 0xFFFFFFFF BCR This field contains the number of bytes yet to be transferred for a given block 0 24 read-write DONE Transactions Done 24 1 read-write 0 DMA transfer is not yet complete. Writing a 0 has no effect. #0 1 DMA transfer completed. Writing a 1 to this bit clears all DMA status bits and should be used in an interrupt service routine to clear the DMA interrupt and error bits. #1 BSY Busy 25 1 read-only 0 DMA channel is inactive. Cleared when the DMA has finished the last transaction. #0 1 BSY is set the first time the channel is enabled after a transfer is initiated. #1 REQ Request 26 1 read-only 0 No request is pending or the channel is currently active. Cleared when the channel is selected. #0 1 The DMA channel has a transfer remaining and the channel is not selected. #1 BED Bus Error on Destination 28 1 read-only 0 No bus error occurred. #0 1 The DMA channel terminated with a bus error during the write portion of a transfer. #1 BES Bus Error on Source 29 1 read-only 0 No bus error occurred. #0 1 The DMA channel terminated with a bus error during the read portion of a transfer. #1 CE Configuration Error 30 1 read-only 0 No configuration error exists. #0 1 A configuration error has occurred. #1 DSR1 DMA_DSR1 register. 0x11B 8 read-write 0 0xFF DCR1 DMA Control Register 0x11C 32 read-write 0 0xFFFFFFFF LCH2 Link Channel 2 0 2 read-write 00 DMA Channel 0 #00 01 DMA Channel 1 #01 10 DMA Channel 2 #10 11 DMA Channel 3 #11 LCH1 Link Channel 1 2 2 read-write 00 DMA Channel 0 #00 01 DMA Channel 1 #01 10 DMA Channel 2 #10 11 DMA Channel 3 #11 LINKCC Link Channel Control 4 2 read-write 00 No channel-to-channel linking #00 01 Perform a link to channel LCH1 after each cycle-steal transfer followed by a link to LCH2 after the BCR decrements to 0. #01 10 Perform a link to channel LCH1 after each cycle-steal transfer #10 11 Perform a link to channel LCH1 after the BCR decrements to 0. #11 D_REQ Disable Request 7 1 read-write 0 ERQ bit is not affected. #0 1 ERQ bit is cleared when the BCR is exhausted. #1 DMOD Destination Address Modulo 8 4 read-write 0000 Buffer disabled #0000 0001 Circular buffer size is 16 bytes #0001 0010 Circular buffer size is 32 bytes #0010 0011 Circular buffer size is 64 bytes #0011 0100 Circular buffer size is 128 bytes #0100 0101 Circular buffer size is 256 bytes #0101 0110 Circular buffer size is 512 bytes #0110 0111 Circular buffer size is 1 KB #0111 1000 Circular buffer size is 2 KB #1000 1001 Circular buffer size is 4 KB #1001 1010 Circular buffer size is 8 KB #1010 1011 Circular buffer size is 16 KB #1011 1100 Circular buffer size is 32 KB #1100 1101 Circular buffer size is 64 KB #1101 1110 Circular buffer size is 128 KB #1110 1111 Circular buffer size is 256 KB #1111 SMOD Source Address Modulo 12 4 read-write 0000 Buffer disabled #0000 0001 Circular buffer size is 16 bytes. #0001 0010 Circular buffer size is 32 bytes. #0010 0011 Circular buffer size is 64 bytes. #0011 0100 Circular buffer size is 128 bytes. #0100 0101 Circular buffer size is 256 bytes. #0101 0110 Circular buffer size is 512 bytes. #0110 0111 Circular buffer size is 1 KB. #0111 1000 Circular buffer size is 2 KB. #1000 1001 Circular buffer size is 4 KB. #1001 1010 Circular buffer size is 8 KB. #1010 1011 Circular buffer size is 16 KB. #1011 1100 Circular buffer size is 32 KB. #1100 1101 Circular buffer size is 64 KB. #1101 1110 Circular buffer size is 128 KB. #1110 1111 Circular buffer size is 256 KB. #1111 START Start Transfer 16 1 write-only 0 DMA inactive #0 1 The DMA begins the transfer in accordance to the values in the TCDn. START is cleared automatically after one module clock and always reads as logic 0. #1 DSIZE Destination Size 17 2 read-write 00 32-bit #00 01 8-bit #01 10 16-bit #10 11 Reserved (generates a configuration error (DSRn[CE]) if incorrectly specified at time of channel activation) #11 DINC Destination Increment 19 1 read-write 0 No change to the DAR after a successful transfer. #0 1 The DAR increments by 1, 2, 4 depending upon the size of the transfer. #1 SSIZE Source Size 20 2 read-write 00 32-bit #00 01 8-bit #01 10 16-bit #10 11 Reserved (generates a configuration error (DSRn[CE]) if incorrectly specified at time of channel activation) #11 SINC Source Increment 22 1 read-write 0 No change to SAR after a successful transfer. #0 1 The SAR increments by 1, 2, 4 as determined by the transfer size. #1 EADREQ Enable asynchronous DMA requests 23 1 read-write 0 Disabled #0 1 Enabled #1 AA Auto-align 28 1 read-write 0 Auto-align disabled #0 1 If SSIZE indicates a transfer no smaller than DSIZE, source accesses are auto-aligned; otherwise, destination accesses are auto-aligned. Source alignment takes precedence over destination alignment. If auto-alignment is enabled, the appropriate address register increments, regardless of DINC or SINC. #1 CS Cycle Steal 29 1 read-write 0 DMA continuously makes read/write transfers until the BCR decrements to 0. #0 1 Forces a single read/write transfer per request. #1 ERQ Enable Peripheral Request 30 1 read-write 0 Peripheral request is ignored. #0 1 Enables peripheral request to initiate transfer. A software-initiated request (setting START) is always enabled. #1 EINT Enable Interrupt on Completion of Transfer 31 1 read-write 0 No interrupt is generated. #0 1 Interrupt signal is enabled. #1 SAR2 Source Address Register 0x120 32 read-write 0 0xFFFFFFFF SAR Each SAR contains the byte address used by the DMA controller to read data 0 32 read-write DAR2 Destination Address Register 0x124 32 read-write 0 0xFFFFFFFF DAR Each DAR contains the byte address used by the DMA controller to write data 0 32 read-write DSR_BCR2 DMA Status Register / Byte Count Register 0x128 32 read-write 0 0xFFFFFFFF BCR This field contains the number of bytes yet to be transferred for a given block 0 24 read-write DONE Transactions Done 24 1 read-write 0 DMA transfer is not yet complete. Writing a 0 has no effect. #0 1 DMA transfer completed. Writing a 1 to this bit clears all DMA status bits and should be used in an interrupt service routine to clear the DMA interrupt and error bits. #1 BSY Busy 25 1 read-only 0 DMA channel is inactive. Cleared when the DMA has finished the last transaction. #0 1 BSY is set the first time the channel is enabled after a transfer is initiated. #1 REQ Request 26 1 read-only 0 No request is pending or the channel is currently active. Cleared when the channel is selected. #0 1 The DMA channel has a transfer remaining and the channel is not selected. #1 BED Bus Error on Destination 28 1 read-only 0 No bus error occurred. #0 1 The DMA channel terminated with a bus error during the write portion of a transfer. #1 BES Bus Error on Source 29 1 read-only 0 No bus error occurred. #0 1 The DMA channel terminated with a bus error during the read portion of a transfer. #1 CE Configuration Error 30 1 read-only 0 No configuration error exists. #0 1 A configuration error has occurred. #1 DSR2 DMA_DSR2 register. 0x12B 8 read-write 0 0xFF DCR2 DMA Control Register 0x12C 32 read-write 0 0xFFFFFFFF LCH2 Link Channel 2 0 2 read-write 00 DMA Channel 0 #00 01 DMA Channel 1 #01 10 DMA Channel 2 #10 11 DMA Channel 3 #11 LCH1 Link Channel 1 2 2 read-write 00 DMA Channel 0 #00 01 DMA Channel 1 #01 10 DMA Channel 2 #10 11 DMA Channel 3 #11 LINKCC Link Channel Control 4 2 read-write 00 No channel-to-channel linking #00 01 Perform a link to channel LCH1 after each cycle-steal transfer followed by a link to LCH2 after the BCR decrements to 0. #01 10 Perform a link to channel LCH1 after each cycle-steal transfer #10 11 Perform a link to channel LCH1 after the BCR decrements to 0. #11 D_REQ Disable Request 7 1 read-write 0 ERQ bit is not affected. #0 1 ERQ bit is cleared when the BCR is exhausted. #1 DMOD Destination Address Modulo 8 4 read-write 0000 Buffer disabled #0000 0001 Circular buffer size is 16 bytes #0001 0010 Circular buffer size is 32 bytes #0010 0011 Circular buffer size is 64 bytes #0011 0100 Circular buffer size is 128 bytes #0100 0101 Circular buffer size is 256 bytes #0101 0110 Circular buffer size is 512 bytes #0110 0111 Circular buffer size is 1 KB #0111 1000 Circular buffer size is 2 KB #1000 1001 Circular buffer size is 4 KB #1001 1010 Circular buffer size is 8 KB #1010 1011 Circular buffer size is 16 KB #1011 1100 Circular buffer size is 32 KB #1100 1101 Circular buffer size is 64 KB #1101 1110 Circular buffer size is 128 KB #1110 1111 Circular buffer size is 256 KB #1111 SMOD Source Address Modulo 12 4 read-write 0000 Buffer disabled #0000 0001 Circular buffer size is 16 bytes. #0001 0010 Circular buffer size is 32 bytes. #0010 0011 Circular buffer size is 64 bytes. #0011 0100 Circular buffer size is 128 bytes. #0100 0101 Circular buffer size is 256 bytes. #0101 0110 Circular buffer size is 512 bytes. #0110 0111 Circular buffer size is 1 KB. #0111 1000 Circular buffer size is 2 KB. #1000 1001 Circular buffer size is 4 KB. #1001 1010 Circular buffer size is 8 KB. #1010 1011 Circular buffer size is 16 KB. #1011 1100 Circular buffer size is 32 KB. #1100 1101 Circular buffer size is 64 KB. #1101 1110 Circular buffer size is 128 KB. #1110 1111 Circular buffer size is 256 KB. #1111 START Start Transfer 16 1 write-only 0 DMA inactive #0 1 The DMA begins the transfer in accordance to the values in the TCDn. START is cleared automatically after one module clock and always reads as logic 0. #1 DSIZE Destination Size 17 2 read-write 00 32-bit #00 01 8-bit #01 10 16-bit #10 11 Reserved (generates a configuration error (DSRn[CE]) if incorrectly specified at time of channel activation) #11 DINC Destination Increment 19 1 read-write 0 No change to the DAR after a successful transfer. #0 1 The DAR increments by 1, 2, 4 depending upon the size of the transfer. #1 SSIZE Source Size 20 2 read-write 00 32-bit #00 01 8-bit #01 10 16-bit #10 11 Reserved (generates a configuration error (DSRn[CE]) if incorrectly specified at time of channel activation) #11 SINC Source Increment 22 1 read-write 0 No change to SAR after a successful transfer. #0 1 The SAR increments by 1, 2, 4 as determined by the transfer size. #1 EADREQ Enable asynchronous DMA requests 23 1 read-write 0 Disabled #0 1 Enabled #1 AA Auto-align 28 1 read-write 0 Auto-align disabled #0 1 If SSIZE indicates a transfer no smaller than DSIZE, source accesses are auto-aligned; otherwise, destination accesses are auto-aligned. Source alignment takes precedence over destination alignment. If auto-alignment is enabled, the appropriate address register increments, regardless of DINC or SINC. #1 CS Cycle Steal 29 1 read-write 0 DMA continuously makes read/write transfers until the BCR decrements to 0. #0 1 Forces a single read/write transfer per request. #1 ERQ Enable Peripheral Request 30 1 read-write 0 Peripheral request is ignored. #0 1 Enables peripheral request to initiate transfer. A software-initiated request (setting START) is always enabled. #1 EINT Enable Interrupt on Completion of Transfer 31 1 read-write 0 No interrupt is generated. #0 1 Interrupt signal is enabled. #1 SAR3 Source Address Register 0x130 32 read-write 0 0xFFFFFFFF SAR Each SAR contains the byte address used by the DMA controller to read data 0 32 read-write DAR3 Destination Address Register 0x134 32 read-write 0 0xFFFFFFFF DAR Each DAR contains the byte address used by the DMA controller to write data 0 32 read-write DSR_BCR3 DMA Status Register / Byte Count Register 0x138 32 read-write 0 0xFFFFFFFF BCR This field contains the number of bytes yet to be transferred for a given block 0 24 read-write DONE Transactions Done 24 1 read-write 0 DMA transfer is not yet complete. Writing a 0 has no effect. #0 1 DMA transfer completed. Writing a 1 to this bit clears all DMA status bits and should be used in an interrupt service routine to clear the DMA interrupt and error bits. #1 BSY Busy 25 1 read-only 0 DMA channel is inactive. Cleared when the DMA has finished the last transaction. #0 1 BSY is set the first time the channel is enabled after a transfer is initiated. #1 REQ Request 26 1 read-only 0 No request is pending or the channel is currently active. Cleared when the channel is selected. #0 1 The DMA channel has a transfer remaining and the channel is not selected. #1 BED Bus Error on Destination 28 1 read-only 0 No bus error occurred. #0 1 The DMA channel terminated with a bus error during the write portion of a transfer. #1 BES Bus Error on Source 29 1 read-only 0 No bus error occurred. #0 1 The DMA channel terminated with a bus error during the read portion of a transfer. #1 CE Configuration Error 30 1 read-only 0 No configuration error exists. #0 1 A configuration error has occurred. #1 DSR3 DMA_DSR3 register. 0x13B 8 read-write 0 0xFF DCR3 DMA Control Register 0x13C 32 read-write 0 0xFFFFFFFF LCH2 Link Channel 2 0 2 read-write 00 DMA Channel 0 #00 01 DMA Channel 1 #01 10 DMA Channel 2 #10 11 DMA Channel 3 #11 LCH1 Link Channel 1 2 2 read-write 00 DMA Channel 0 #00 01 DMA Channel 1 #01 10 DMA Channel 2 #10 11 DMA Channel 3 #11 LINKCC Link Channel Control 4 2 read-write 00 No channel-to-channel linking #00 01 Perform a link to channel LCH1 after each cycle-steal transfer followed by a link to LCH2 after the BCR decrements to 0. #01 10 Perform a link to channel LCH1 after each cycle-steal transfer #10 11 Perform a link to channel LCH1 after the BCR decrements to 0. #11 D_REQ Disable Request 7 1 read-write 0 ERQ bit is not affected. #0 1 ERQ bit is cleared when the BCR is exhausted. #1 DMOD Destination Address Modulo 8 4 read-write 0000 Buffer disabled #0000 0001 Circular buffer size is 16 bytes #0001 0010 Circular buffer size is 32 bytes #0010 0011 Circular buffer size is 64 bytes #0011 0100 Circular buffer size is 128 bytes #0100 0101 Circular buffer size is 256 bytes #0101 0110 Circular buffer size is 512 bytes #0110 0111 Circular buffer size is 1 KB #0111 1000 Circular buffer size is 2 KB #1000 1001 Circular buffer size is 4 KB #1001 1010 Circular buffer size is 8 KB #1010 1011 Circular buffer size is 16 KB #1011 1100 Circular buffer size is 32 KB #1100 1101 Circular buffer size is 64 KB #1101 1110 Circular buffer size is 128 KB #1110 1111 Circular buffer size is 256 KB #1111 SMOD Source Address Modulo 12 4 read-write 0000 Buffer disabled #0000 0001 Circular buffer size is 16 bytes. #0001 0010 Circular buffer size is 32 bytes. #0010 0011 Circular buffer size is 64 bytes. #0011 0100 Circular buffer size is 128 bytes. #0100 0101 Circular buffer size is 256 bytes. #0101 0110 Circular buffer size is 512 bytes. #0110 0111 Circular buffer size is 1 KB. #0111 1000 Circular buffer size is 2 KB. #1000 1001 Circular buffer size is 4 KB. #1001 1010 Circular buffer size is 8 KB. #1010 1011 Circular buffer size is 16 KB. #1011 1100 Circular buffer size is 32 KB. #1100 1101 Circular buffer size is 64 KB. #1101 1110 Circular buffer size is 128 KB. #1110 1111 Circular buffer size is 256 KB. #1111 START Start Transfer 16 1 write-only 0 DMA inactive #0 1 The DMA begins the transfer in accordance to the values in the TCDn. START is cleared automatically after one module clock and always reads as logic 0. #1 DSIZE Destination Size 17 2 read-write 00 32-bit #00 01 8-bit #01 10 16-bit #10 11 Reserved (generates a configuration error (DSRn[CE]) if incorrectly specified at time of channel activation) #11 DINC Destination Increment 19 1 read-write 0 No change to the DAR after a successful transfer. #0 1 The DAR increments by 1, 2, 4 depending upon the size of the transfer. #1 SSIZE Source Size 20 2 read-write 00 32-bit #00 01 8-bit #01 10 16-bit #10 11 Reserved (generates a configuration error (DSRn[CE]) if incorrectly specified at time of channel activation) #11 SINC Source Increment 22 1 read-write 0 No change to SAR after a successful transfer. #0 1 The SAR increments by 1, 2, 4 as determined by the transfer size. #1 EADREQ Enable asynchronous DMA requests 23 1 read-write 0 Disabled #0 1 Enabled #1 AA Auto-align 28 1 read-write 0 Auto-align disabled #0 1 If SSIZE indicates a transfer no smaller than DSIZE, source accesses are auto-aligned; otherwise, destination accesses are auto-aligned. Source alignment takes precedence over destination alignment. If auto-alignment is enabled, the appropriate address register increments, regardless of DINC or SINC. #1 CS Cycle Steal 29 1 read-write 0 DMA continuously makes read/write transfers until the BCR decrements to 0. #0 1 Forces a single read/write transfer per request. #1 ERQ Enable Peripheral Request 30 1 read-write 0 Peripheral request is ignored. #0 1 Enables peripheral request to initiate transfer. A software-initiated request (setting START) is always enabled. #1 EINT Enable Interrupt on Completion of Transfer 31 1 read-write 0 No interrupt is generated. #0 1 Interrupt signal is enabled. #1 FTFA Flash Memory Interface FTFA_ 0x40020000 0 0x14 registers FTFA 5 FSTAT Flash Status Register 0 8 read-write 0 0xFF MGSTAT0 Memory Controller Command Completion Status Flag 0 1 read-only FPVIOL Flash Protection Violation Flag 4 1 read-write 0 No protection violation detected #0 1 Protection violation detected #1 ACCERR Flash Access Error Flag 5 1 read-write 0 No access error detected #0 1 Access error detected #1 RDCOLERR Flash Read Collision Error Flag 6 1 read-write 0 No collision error detected #0 1 Collision error detected #1 CCIF Command Complete Interrupt Flag 7 1 read-write 0 Flash command in progress #0 1 Flash command has completed #1 FCNFG Flash Configuration Register 0x1 8 read-write 0 0xFF ERSSUSP Erase Suspend 4 1 read-write 0 No suspend requested #0 1 Suspend the current Erase Flash Sector command execution. #1 ERSAREQ Erase All Request 5 1 read-only 0 No request or request complete #0 1 Request to: run the Erase All Blocks command, verify the erased state, program the security byte in the Flash Configuration Field to the unsecure state, and release MCU security by setting the FSEC[SEC] field to the unsecure state. #1 RDCOLLIE Read Collision Error Interrupt Enable 6 1 read-write 0 Read collision error interrupt disabled #0 1 Read collision error interrupt enabled. An interrupt request is generated whenever a flash memory read collision error is detected (see the description of FSTAT[RDCOLERR]). #1 CCIE Command Complete Interrupt Enable 7 1 read-write 0 Command complete interrupt disabled #0 1 Command complete interrupt enabled. An interrupt request is generated whenever the FSTAT[CCIF] flag is set. #1 FSEC Flash Security Register 0x2 8 read-only 0 0 SEC Flash Security 0 2 read-only 00 MCU security status is secure. #00 01 MCU security status is secure. #01 10 MCU security status is unsecure. (The standard shipping condition of the flash memory module is unsecure.) #10 11 MCU security status is secure. #11 FSLACC Freescale Failure Analysis Access Code 2 2 read-only 00 Freescale factory access granted #00 01 Freescale factory access denied #01 10 Freescale factory access denied #10 11 Freescale factory access granted #11 MEEN Mass Erase Enable Bits 4 2 read-only 00 Mass erase is enabled #00 01 Mass erase is enabled #01 10 Mass erase is disabled #10 11 Mass erase is enabled #11 KEYEN Backdoor Key Security Enable 6 2 read-only 00 Backdoor key access disabled #00 01 Backdoor key access disabled (preferred KEYEN state to disable backdoor key access) #01 10 Backdoor key access enabled #10 11 Backdoor key access disabled #11 FOPT Flash Option Register 0x3 8 read-only 0 0 OPT Nonvolatile Option 0 8 read-only 12 0x1 3,2,1,0,7,6,5,4,B,A,9,8 FCCOB%s Flash Common Command Object Registers 0x4 8 read-write 0 0xFF CCOBn The FCCOB register provides a command code and relevant parameters to the memory controller 0 8 read-write 4 0x1 3,2,1,0 FPROT%s Program Flash Protection Registers 0x10 8 read-write 0 0 PROT Program Flash Region Protect 0 8 read-write 0 Program flash region is protected. #0 1 Program flash region is not protected #1 DMAMUX0 DMA channel multiplexor DMAMUX0_ 0x40021000 0 0x4 registers 4 0x1 0,1,2,3 CHCFG%s Channel Configuration register 0 8 read-write 0 0xFF SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 3 UART0_Tx_Signal #11 4 UART1_Rx_Signal #100 5 UART1_Tx_Signal #101 6 UART2_Rx_Signal #110 7 UART2_Tx_Signal #111 14 I2S0_Rx_Signal #1110 15 I2S0_Tx_Signal #1111 16 SPI0_Rx_Signal #10000 17 SPI0_Tx_Signal #10001 18 SPI1_Rx_Signal #10010 19 SPI1_Tx_Signal #10011 22 I2C0_Signal #10110 23 I2C1_Signal #10111 24 TPM0_Channel0_Signal #11000 25 TPM0_Channel1_Signal #11001 26 TPM0_Channel2_Signal #11010 27 TPM0_Channel3_Signal #11011 28 TPM0_Channel4_Signal #11100 29 TPM0_Channel5_Signal #11101 32 TPM1_Channel0_Signal #100000 33 TPM1_Channel1_Signal #100001 34 TPM2_Channel0_Signal #100010 35 TPM2_Channel1_Signal #100011 40 ADC0_Signal #101000 42 CMP0_Signal #101010 45 DAC0_Signal #101101 49 PortA_Signal #110001 51 PortC_Signal #110011 52 PortD_Signal #110100 54 TPM0_Overflow_Signal #110110 55 TPM1_Overflow_Signal #110111 56 TPM2_Overflow_Signal #111000 57 TSI_Signal #111001 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 I2S0 Inter-IC Sound / Synchronous Audio Interface I2S0_ 0x4002F000 0 0x108 registers I2S0 23 TCSR SAI Transmit Control Register 0 32 read-write 0 0xFFFFFFFF FWDE FIFO Warning DMA Enable 1 1 read-write 0 Disables the DMA request. #0 1 Enables the DMA request. #1 FWIE FIFO Warning Interrupt Enable 9 1 read-write 0 Disables the interrupt. #0 1 Enables the interrupt. #1 FEIE FIFO Error Interrupt Enable 10 1 read-write 0 Disables the interrupt. #0 1 Enables the interrupt. #1 SEIE Sync Error Interrupt Enable 11 1 read-write 0 Disables interrupt. #0 1 Enables interrupt. #1 WSIE Word Start Interrupt Enable 12 1 read-write 0 Disables interrupt. #0 1 Enables interrupt. #1 FWF FIFO Warning Flag 17 1 read-only 0 No enabled transmit FIFO is empty. #0 1 Enabled transmit FIFO is empty. #1 FEF FIFO Error Flag 18 1 read-write 0 Transmit underrun not detected. #0 1 Transmit underrun detected. #1 SEF Sync Error Flag 19 1 read-write 0 Sync error not detected. #0 1 Frame sync error detected. #1 WSF Word Start Flag 20 1 read-write 0 Start of word not detected. #0 1 Start of word detected. #1 SR Software Reset 24 1 read-write 0 No effect. #0 1 Software reset. #1 FR FIFO Reset 25 1 write-only 0 No effect. #0 1 FIFO reset. #1 BCE Bit Clock Enable 28 1 read-write 0 Transmit bit clock is disabled. #0 1 Transmit bit clock is enabled. #1 DBGE Debug Enable 29 1 read-write 0 Transmitter is disabled in Debug mode, after completing the current frame. #0 1 Transmitter is enabled in Debug mode. #1 STOPE Stop Enable 30 1 read-write 0 Transmitter disabled in Stop mode. #0 1 Transmitter enabled in Stop mode. #1 TE Transmitter Enable 31 1 read-write 0 Transmitter is disabled. #0 1 Transmitter is enabled, or transmitter has been disabled and has not yet reached end of frame. #1 TCR2 SAI Transmit Configuration 2 Register 0x8 32 read-write 0 0xFFFFFFFF DIV Bit Clock Divide 0 8 read-write BCD Bit Clock Direction 24 1 read-write 0 Bit clock is generated externally in Slave mode. #0 1 Bit clock is generated internally in Master mode. #1 BCP Bit Clock Polarity 25 1 read-write 0 Bit clock is active high with drive outputs on rising edge and sample inputs on falling edge. #0 1 Bit clock is active low with drive outputs on falling edge and sample inputs on rising edge. #1 MSEL MCLK Select 26 2 read-write 00 Bus Clock selected. #00 01 Master Clock (MCLK) 1 option selected. #01 10 Master Clock (MCLK) 2 option selected. #10 11 Master Clock (MCLK) 3 option selected. #11 BCI Bit Clock Input 28 1 read-write 0 No effect. #0 1 Internal logic is clocked as if bit clock was externally generated. #1 BCS Bit Clock Swap 29 1 read-write 0 Use the normal bit clock source. #0 1 Swap the bit clock source. #1 SYNC Synchronous Mode 30 2 read-write 00 Asynchronous mode. #00 01 Synchronous with receiver. #01 10 Synchronous with another SAI transmitter. #10 11 Synchronous with another SAI receiver. #11 TCR3 SAI Transmit Configuration 3 Register 0xC 32 read-write 0 0xFFFFFFFF WDFL Word Flag Configuration 0 1 read-write TCE Transmit Channel Enable 16 1 read-write 0 Transmit data channel N is disabled. #0 1 Transmit data channel N is enabled. #1 TCR4 SAI Transmit Configuration 4 Register 0x10 32 read-write 0 0xFFFFFFFF FSD Frame Sync Direction 0 1 read-write 0 Frame sync is generated externally in Slave mode. #0 1 Frame sync is generated internally in Master mode. #1 FSP Frame Sync Polarity 1 1 read-write 0 Frame sync is active high. #0 1 Frame sync is active low. #1 FSE Frame Sync Early 3 1 read-write 0 Frame sync asserts with the first bit of the frame. #0 1 Frame sync asserts one bit before the first bit of the frame. #1 MF MSB First 4 1 read-write 0 LSB is transmitted first. #0 1 MSB is transmitted first. #1 SYWD Sync Width 8 5 read-write FRSZ Frame size 16 1 read-write TCR5 SAI Transmit Configuration 5 Register 0x14 32 read-write 0 0xFFFFFFFF FBT First Bit Shifted 8 5 read-write W0W Word 0 Width 16 5 read-write WNW Word N Width 24 5 read-write TDR SAI Transmit Data Register 0x20 32 write-only 0 0xFFFFFFFF TDR Transmit Data Register 0 32 write-only TMR SAI Transmit Mask Register 0x60 32 read-write 0 0xFFFFFFFF TWM Transmit Word Mask 0 2 read-write 0 Word N is enabled. #00 1 Word N is masked. The transmit data pins are tri-stated when masked. #01 RCSR SAI Receive Control Register 0x80 32 read-write 0 0xFFFFFFFF FWDE FIFO Warning DMA Enable 1 1 read-write 0 Disables the DMA request. #0 1 Enables the DMA request. #1 FWIE FIFO Warning Interrupt Enable 9 1 read-write 0 Disables the interrupt. #0 1 Enables the interrupt. #1 FEIE FIFO Error Interrupt Enable 10 1 read-write 0 Disables the interrupt. #0 1 Enables the interrupt. #1 SEIE Sync Error Interrupt Enable 11 1 read-write 0 Disables interrupt. #0 1 Enables interrupt. #1 WSIE Word Start Interrupt Enable 12 1 read-write 0 Disables interrupt. #0 1 Enables interrupt. #1 FWF FIFO Warning Flag 17 1 read-only 0 No enabled receive FIFO is full. #0 1 Enabled receive FIFO is full. #1 FEF FIFO Error Flag 18 1 read-write 0 Receive overflow not detected. #0 1 Receive overflow detected. #1 SEF Sync Error Flag 19 1 read-write 0 Sync error not detected. #0 1 Frame sync error detected. #1 WSF Word Start Flag 20 1 read-write 0 Start of word not detected. #0 1 Start of word detected. #1 SR Software Reset 24 1 read-write 0 No effect. #0 1 Software reset. #1 FR FIFO Reset 25 1 write-only 0 No effect. #0 1 FIFO reset. #1 BCE Bit Clock Enable 28 1 read-write 0 Receive bit clock is disabled. #0 1 Receive bit clock is enabled. #1 DBGE Debug Enable 29 1 read-write 0 Receiver is disabled in Debug mode, after completing the current frame. #0 1 Receiver is enabled in Debug mode. #1 STOPE Stop Enable 30 1 read-write 0 Receiver disabled in Stop mode. #0 1 Receiver enabled in Stop mode. #1 RE Receiver Enable 31 1 read-write 0 Receiver is disabled. #0 1 Receiver is enabled, or receiver has been disabled and has not yet reached end of frame. #1 RCR2 SAI Receive Configuration 2 Register 0x88 32 read-write 0 0xFFFFFFFF DIV Bit Clock Divide 0 8 read-write BCD Bit Clock Direction 24 1 read-write 0 Bit clock is generated externally in Slave mode. #0 1 Bit clock is generated internally in Master mode. #1 BCP Bit Clock Polarity 25 1 read-write 0 Bit Clock is active high with drive outputs on rising edge and sample inputs on falling edge. #0 1 Bit Clock is active low with drive outputs on falling edge and sample inputs on rising edge. #1 MSEL MCLK Select 26 2 read-write 00 Bus Clock selected. #00 01 Master Clock (MCLK) 1 option selected. #01 10 Master Clock (MCLK) 2 option selected. #10 11 Master Clock (MCLK) 3 option selected. #11 BCI Bit Clock Input 28 1 read-write 0 No effect. #0 1 Internal logic is clocked as if bit clock was externally generated. #1 BCS Bit Clock Swap 29 1 read-write 0 Use the normal bit clock source. #0 1 Swap the bit clock source. #1 SYNC Synchronous Mode 30 2 read-write 00 Asynchronous mode. #00 01 Synchronous with transmitter. #01 10 Synchronous with another SAI receiver. #10 11 Synchronous with another SAI transmitter. #11 RCR3 SAI Receive Configuration 3 Register 0x8C 32 read-write 0 0xFFFFFFFF WDFL Word Flag Configuration 0 1 read-write RCE Receive Channel Enable 16 1 read-write 0 Receive data channel N is disabled. #0 1 Receive data channel N is enabled. #1 RCR4 SAI Receive Configuration 4 Register 0x90 32 read-write 0 0xFFFFFFFF FSD Frame Sync Direction 0 1 read-write 0 Frame Sync is generated externally in Slave mode. #0 1 Frame Sync is generated internally in Master mode. #1 FSP Frame Sync Polarity 1 1 read-write 0 Frame sync is active high. #0 1 Frame sync is active low. #1 FSE Frame Sync Early 3 1 read-write 0 Frame sync asserts with the first bit of the frame. #0 1 Frame sync asserts one bit before the first bit of the frame. #1 MF MSB First 4 1 read-write 0 LSB is received first. #0 1 MSB is received first. #1 SYWD Sync Width 8 5 read-write FRSZ Frame Size 16 1 read-write RCR5 SAI Receive Configuration 5 Register 0x94 32 read-write 0 0xFFFFFFFF FBT First Bit Shifted 8 5 read-write W0W Word 0 Width 16 5 read-write WNW Word N Width 24 5 read-write RDR SAI Receive Data Register 0xA0 32 read-only 0 0xFFFFFFFF RDR Receive Data Register 0 32 read-only RMR SAI Receive Mask Register 0xE0 32 read-write 0 0xFFFFFFFF RWM Receive Word Mask 0 2 read-write 0 Word N is enabled. #00 1 Word N is masked. #01 MCR SAI MCLK Control Register 0x100 32 read-write 0 0xFFFFFFFF MICS MCLK Input Clock Select 24 2 read-write 00 MCLK divider input clock 0 selected. #00 01 MCLK divider input clock 1 selected. #01 10 MCLK divider input clock 2 selected. #10 11 MCLK divider input clock 3 selected. #11 MOE MCLK Output Enable 30 1 read-write 0 MCLK signal pin is configured as an input that bypasses the MCLK divider. #0 1 MCLK signal pin is configured as an output from the MCLK divider and the MCLK divider is enabled. #1 DUF Divider Update Flag 31 1 read-only 0 MCLK divider ratio is not being updated currently. #0 1 MCLK divider ratio is updating on-the-fly. Further updates to the MCLK divider ratio are blocked while this flag remains set. #1 MDR SAI MCLK Divide Register 0x104 32 read-write 0 0xFFFFFFFF DIVIDE MCLK Divide 0 12 read-write FRACT MCLK Fraction 12 8 read-write PIT Periodic Interrupt Timer PIT_ 0x40037000 0 0x120 registers PIT 22 MCR PIT Module Control Register 0 32 read-write 0x6 0xFFFFFFFF FRZ Freeze 0 1 read-write 0 Timers continue to run in Debug mode. #0 1 Timers are stopped in Debug mode. #1 MDIS Module Disable - (PIT section) 1 1 read-write 0 Clock for standard PIT timers is enabled. #0 1 Clock for standard PIT timers is disabled. #1 LTMR64H PIT Upper Lifetime Timer Register 0xE0 32 read-only 0 0xFFFFFFFF LTH Life Timer value 0 32 read-only LTMR64L PIT Lower Lifetime Timer Register 0xE4 32 read-only 0 0xFFFFFFFF LTL Life Timer value 0 32 read-only 2 0x10 0,1 LDVAL%s Timer Load Value Register 0x100 32 read-write 0 0xFFFFFFFF TSV Timer Start Value 0 32 read-write 2 0x10 0,1 CVAL%s Current Timer Value Register 0x104 32 read-only 0 0xFFFFFFFF TVL Current Timer Value 0 32 read-only 2 0x10 0,1 TCTRL%s Timer Control Register 0x108 32 read-write 0 0xFFFFFFFF TEN Timer Enable 0 1 read-write 0 Timer n is disabled. #0 1 Timer n is enabled. #1 TIE Timer Interrupt Enable 1 1 read-write 0 Interrupt requests from Timer n are disabled. #0 1 Interrupt will be requested whenever TIF is set. #1 CHN Chain Mode 2 1 read-write 0 Timer is not chained. #0 1 Timer is chained to previous timer. For example, for Channel 2, if this field is set, Timer 2 is chained to Timer 1. #1 2 0x10 0,1 TFLG%s Timer Flag Register 0x10C 32 read-write 0 0xFFFFFFFF TIF Timer Interrupt Flag 0 1 read-write 0 Timeout has not yet occurred. #0 1 Timeout has occurred. #1 TPM0 Timer/PWM Module TPM TPM0_ 0x40038000 0 0x88 registers TPM0 17 SC Status and Control 0 32 read-write 0 0xFFFFFFFF PS Prescale Factor Selection 0 3 read-write 000 Divide by 1 #000 001 Divide by 2 #001 010 Divide by 4 #010 011 Divide by 8 #011 100 Divide by 16 #100 101 Divide by 32 #101 110 Divide by 64 #110 111 Divide by 128 #111 CMOD Clock Mode Selection 3 2 read-write 00 TPM counter is disabled #00 01 TPM counter increments on every TPM counter clock #01 10 TPM counter increments on rising edge of TPM_EXTCLK synchronized to the TPM counter clock #10 CPWMS Center-Aligned PWM Select 5 1 read-write 0 TPM counter operates in up counting mode. #0 1 TPM counter operates in up-down counting mode. #1 TOIE Timer Overflow Interrupt Enable 6 1 read-write 0 Disable TOF interrupts. Use software polling or DMA request. #0 1 Enable TOF interrupts. An interrupt is generated when TOF equals one. #1 TOF Timer Overflow Flag 7 1 read-write 0 TPM counter has not overflowed. #0 1 TPM counter has overflowed. #1 DMA DMA Enable 8 1 read-write 0 Disables DMA transfers. #0 1 Enables DMA transfers. #1 CNT Counter 0x4 32 read-write 0 0xFFFFFFFF COUNT Counter value 0 16 read-write MOD Modulo 0x8 32 read-write 0xFFFF 0xFFFFFFFF MOD Modulo value 0 16 read-write 6 0x8 0,1,2,3,4,5 C%sSC Channel (n) Status and Control 0xC 32 read-write 0 0xFFFFFFFF DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. #0 1 Enable channel interrupts. #1 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 6 0x8 0,1,2,3,4,5 C%sV Channel (n) Value 0x10 32 read-write 0 0xFFFFFFFF VAL Channel Value 0 16 read-write STATUS Capture and Compare Status 0x50 32 read-write 0 0xFFFFFFFF CH0F Channel 0 Flag 0 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH1F Channel 1 Flag 1 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH2F Channel 2 Flag 2 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH3F Channel 3 Flag 3 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH4F Channel 4 Flag 4 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH5F Channel 5 Flag 5 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 TOF Timer Overflow Flag 8 1 read-write 0 TPM counter has not overflowed. #0 1 TPM counter has overflowed. #1 CONF Configuration 0x84 32 read-write 0 0xFFFFFFFF DOZEEN Doze Enable 5 1 read-write 0 Internal TPM counter continues in Doze mode. #0 1 Internal TPM counter is paused and does not increment during Doze mode. Trigger inputs and input capture events are also ignored. #1 DBGMODE Debug Mode 6 2 read-write 00 TPM counter is paused and does not increment during debug mode. Trigger inputs and input capture events are also ignored. #00 11 TPM counter continues in debug mode. #11 GTBEEN Global time base enable 9 1 read-write 0 All channels use the internally generated TPM counter as their timebase #0 1 All channels use an externally generated global timebase as their timebase #1 CSOT Counter Start on Trigger 16 1 read-write 0 TPM counter starts to increment immediately, once it is enabled. #0 1 TPM counter only starts to increment when it a rising edge on the selected input trigger is detected, after it has been enabled or after it has stopped due to overflow. #1 CSOO Counter Stop On Overflow 17 1 read-write 0 TPM counter continues incrementing or decrementing after overflow #0 1 TPM counter stops incrementing or decrementing after overflow. #1 CROT Counter Reload On Trigger 18 1 read-write 0 Counter is not reloaded due to a rising edge on the selected input trigger #0 1 Counter is reloaded when a rising edge is detected on the selected input trigger #1 TRGSEL Trigger Select 24 4 read-write TPM1 Timer/PWM Module TPM TPM1_ 0x40039000 0 0x88 registers TPM1 18 SC Status and Control 0 32 read-write 0 0xFFFFFFFF PS Prescale Factor Selection 0 3 read-write 000 Divide by 1 #000 001 Divide by 2 #001 010 Divide by 4 #010 011 Divide by 8 #011 100 Divide by 16 #100 101 Divide by 32 #101 110 Divide by 64 #110 111 Divide by 128 #111 CMOD Clock Mode Selection 3 2 read-write 00 TPM counter is disabled #00 01 TPM counter increments on every TPM counter clock #01 10 TPM counter increments on rising edge of TPM_EXTCLK synchronized to the TPM counter clock #10 CPWMS Center-Aligned PWM Select 5 1 read-write 0 TPM counter operates in up counting mode. #0 1 TPM counter operates in up-down counting mode. #1 TOIE Timer Overflow Interrupt Enable 6 1 read-write 0 Disable TOF interrupts. Use software polling or DMA request. #0 1 Enable TOF interrupts. An interrupt is generated when TOF equals one. #1 TOF Timer Overflow Flag 7 1 read-write 0 TPM counter has not overflowed. #0 1 TPM counter has overflowed. #1 DMA DMA Enable 8 1 read-write 0 Disables DMA transfers. #0 1 Enables DMA transfers. #1 CNT Counter 0x4 32 read-write 0 0xFFFFFFFF COUNT Counter value 0 16 read-write MOD Modulo 0x8 32 read-write 0xFFFF 0xFFFFFFFF MOD Modulo value 0 16 read-write 2 0x8 0,1 C%sSC Channel (n) Status and Control 0xC 32 read-write 0 0xFFFFFFFF DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. #0 1 Enable channel interrupts. #1 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 2 0x8 0,1 C%sV Channel (n) Value 0x10 32 read-write 0 0xFFFFFFFF VAL Channel Value 0 16 read-write STATUS Capture and Compare Status 0x50 32 read-write 0 0xFFFFFFFF CH0F Channel 0 Flag 0 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH1F Channel 1 Flag 1 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH2F Channel 2 Flag 2 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH3F Channel 3 Flag 3 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH4F Channel 4 Flag 4 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH5F Channel 5 Flag 5 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 TOF Timer Overflow Flag 8 1 read-write 0 TPM counter has not overflowed. #0 1 TPM counter has overflowed. #1 CONF Configuration 0x84 32 read-write 0 0xFFFFFFFF DOZEEN Doze Enable 5 1 read-write 0 Internal TPM counter continues in Doze mode. #0 1 Internal TPM counter is paused and does not increment during Doze mode. Trigger inputs and input capture events are also ignored. #1 DBGMODE Debug Mode 6 2 read-write 00 TPM counter is paused and does not increment during debug mode. Trigger inputs and input capture events are also ignored. #00 11 TPM counter continues in debug mode. #11 GTBEEN Global time base enable 9 1 read-write 0 All channels use the internally generated TPM counter as their timebase #0 1 All channels use an externally generated global timebase as their timebase #1 CSOT Counter Start on Trigger 16 1 read-write 0 TPM counter starts to increment immediately, once it is enabled. #0 1 TPM counter only starts to increment when it a rising edge on the selected input trigger is detected, after it has been enabled or after it has stopped due to overflow. #1 CSOO Counter Stop On Overflow 17 1 read-write 0 TPM counter continues incrementing or decrementing after overflow #0 1 TPM counter stops incrementing or decrementing after overflow. #1 CROT Counter Reload On Trigger 18 1 read-write 0 Counter is not reloaded due to a rising edge on the selected input trigger #0 1 Counter is reloaded when a rising edge is detected on the selected input trigger #1 TRGSEL Trigger Select 24 4 read-write TPM2 Timer/PWM Module TPM TPM2_ 0x4003A000 0 0x88 registers TPM2 19 SC Status and Control 0 32 read-write 0 0xFFFFFFFF PS Prescale Factor Selection 0 3 read-write 000 Divide by 1 #000 001 Divide by 2 #001 010 Divide by 4 #010 011 Divide by 8 #011 100 Divide by 16 #100 101 Divide by 32 #101 110 Divide by 64 #110 111 Divide by 128 #111 CMOD Clock Mode Selection 3 2 read-write 00 TPM counter is disabled #00 01 TPM counter increments on every TPM counter clock #01 10 TPM counter increments on rising edge of TPM_EXTCLK synchronized to the TPM counter clock #10 CPWMS Center-Aligned PWM Select 5 1 read-write 0 TPM counter operates in up counting mode. #0 1 TPM counter operates in up-down counting mode. #1 TOIE Timer Overflow Interrupt Enable 6 1 read-write 0 Disable TOF interrupts. Use software polling or DMA request. #0 1 Enable TOF interrupts. An interrupt is generated when TOF equals one. #1 TOF Timer Overflow Flag 7 1 read-write 0 TPM counter has not overflowed. #0 1 TPM counter has overflowed. #1 DMA DMA Enable 8 1 read-write 0 Disables DMA transfers. #0 1 Enables DMA transfers. #1 CNT Counter 0x4 32 read-write 0 0xFFFFFFFF COUNT Counter value 0 16 read-write MOD Modulo 0x8 32 read-write 0xFFFF 0xFFFFFFFF MOD Modulo value 0 16 read-write 2 0x8 0,1 C%sSC Channel (n) Status and Control 0xC 32 read-write 0 0xFFFFFFFF DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. #0 1 Enable channel interrupts. #1 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 2 0x8 0,1 C%sV Channel (n) Value 0x10 32 read-write 0 0xFFFFFFFF VAL Channel Value 0 16 read-write STATUS Capture and Compare Status 0x50 32 read-write 0 0xFFFFFFFF CH0F Channel 0 Flag 0 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH1F Channel 1 Flag 1 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH2F Channel 2 Flag 2 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH3F Channel 3 Flag 3 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH4F Channel 4 Flag 4 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH5F Channel 5 Flag 5 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 TOF Timer Overflow Flag 8 1 read-write 0 TPM counter has not overflowed. #0 1 TPM counter has overflowed. #1 CONF Configuration 0x84 32 read-write 0 0xFFFFFFFF DOZEEN Doze Enable 5 1 read-write 0 Internal TPM counter continues in Doze mode. #0 1 Internal TPM counter is paused and does not increment during Doze mode. Trigger inputs and input capture events are also ignored. #1 DBGMODE Debug Mode 6 2 read-write 00 TPM counter is paused and does not increment during debug mode. Trigger inputs and input capture events are also ignored. #00 11 TPM counter continues in debug mode. #11 GTBEEN Global time base enable 9 1 read-write 0 All channels use the internally generated TPM counter as their timebase #0 1 All channels use an externally generated global timebase as their timebase #1 CSOT Counter Start on Trigger 16 1 read-write 0 TPM counter starts to increment immediately, once it is enabled. #0 1 TPM counter only starts to increment when it a rising edge on the selected input trigger is detected, after it has been enabled or after it has stopped due to overflow. #1 CSOO Counter Stop On Overflow 17 1 read-write 0 TPM counter continues incrementing or decrementing after overflow #0 1 TPM counter stops incrementing or decrementing after overflow. #1 CROT Counter Reload On Trigger 18 1 read-write 0 Counter is not reloaded due to a rising edge on the selected input trigger #0 1 Counter is reloaded when a rising edge is detected on the selected input trigger #1 TRGSEL Trigger Select 24 4 read-write ADC0 Analog-to-Digital Converter ADC0_ 0x4003B000 0 0x70 registers ADC0 15 2 0x4 A,B SC1%s ADC Status and Control Registers 1 0 32 read-write 0x1F 0xFFFFFFFF ADCH Input channel select 0 5 read-write 00000 When DIFF=0, DADP0 is selected as input; when DIFF=1, DAD0 is selected as input. #00000 00001 When DIFF=0, DADP1 is selected as input; when DIFF=1, DAD1 is selected as input. #00001 00010 When DIFF=0, DADP2 is selected as input; when DIFF=1, DAD2 is selected as input. #00010 00011 When DIFF=0, DADP3 is selected as input; when DIFF=1, DAD3 is selected as input. #00011 00100 When DIFF=0, AD4 is selected as input; when DIFF=1, it is reserved. #00100 00101 When DIFF=0, AD5 is selected as input; when DIFF=1, it is reserved. #00101 00110 When DIFF=0, AD6 is selected as input; when DIFF=1, it is reserved. #00110 00111 When DIFF=0, AD7 is selected as input; when DIFF=1, it is reserved. #00111 01000 When DIFF=0, AD8 is selected as input; when DIFF=1, it is reserved. #01000 01001 When DIFF=0, AD9 is selected as input; when DIFF=1, it is reserved. #01001 01010 When DIFF=0, AD10 is selected as input; when DIFF=1, it is reserved. #01010 01011 When DIFF=0, AD11 is selected as input; when DIFF=1, it is reserved. #01011 01100 When DIFF=0, AD12 is selected as input; when DIFF=1, it is reserved. #01100 01101 When DIFF=0, AD13 is selected as input; when DIFF=1, it is reserved. #01101 01110 When DIFF=0, AD14 is selected as input; when DIFF=1, it is reserved. #01110 01111 When DIFF=0, AD15 is selected as input; when DIFF=1, it is reserved. #01111 10000 When DIFF=0, AD16 is selected as input; when DIFF=1, it is reserved. #10000 10001 When DIFF=0, AD17 is selected as input; when DIFF=1, it is reserved. #10001 10010 When DIFF=0, AD18 is selected as input; when DIFF=1, it is reserved. #10010 10011 When DIFF=0, AD19 is selected as input; when DIFF=1, it is reserved. #10011 10100 When DIFF=0, AD20 is selected as input; when DIFF=1, it is reserved. #10100 10101 When DIFF=0, AD21 is selected as input; when DIFF=1, it is reserved. #10101 10110 When DIFF=0, AD22 is selected as input; when DIFF=1, it is reserved. #10110 10111 When DIFF=0, AD23 is selected as input; when DIFF=1, it is reserved. #10111 11010 When DIFF=0, Temp Sensor (single-ended) is selected as input; when DIFF=1, Temp Sensor (differential) is selected as input. #11010 11011 When DIFF=0, Bandgap (single-ended) is selected as input; when DIFF=1, Bandgap (differential) is selected as input. #11011 11101 When DIFF=0,VREFSH is selected as input; when DIFF=1, -VREFSH (differential) is selected as input. Voltage reference selected is determined by SC2[REFSEL]. #11101 11110 When DIFF=0,VREFSL is selected as input; when DIFF=1, it is reserved. Voltage reference selected is determined by SC2[REFSEL]. #11110 11111 Module is disabled. #11111 DIFF Differential Mode Enable 5 1 read-write 0 Single-ended conversions and input channels are selected. #0 1 Differential conversions and input channels are selected. #1 AIEN Interrupt Enable 6 1 read-write 0 Conversion complete interrupt is disabled. #0 1 Conversion complete interrupt is enabled. #1 COCO Conversion Complete Flag 7 1 read-only 0 Conversion is not completed. #0 1 Conversion is completed. #1 CFG1 ADC Configuration Register 1 0x8 32 read-write 0 0xFFFFFFFF ADICLK Input Clock Select 0 2 read-write 00 Bus clock #00 01 Alternate clock 2 (ALTCLK2) #01 10 Alternate clock (ALTCLK) #10 11 Asynchronous clock (ADACK) #11 MODE Conversion mode selection 2 2 read-write 00 When DIFF=0:It is single-ended 8-bit conversion; when DIFF=1, it is differential 9-bit conversion with 2's complement output. #00 01 When DIFF=0:It is single-ended 12-bit conversion ; when DIFF=1, it is differential 13-bit conversion with 2's complement output. #01 10 When DIFF=0:It is single-ended 10-bit conversion. ; when DIFF=1, it is differential 11-bit conversion with 2's complement output #10 11 When DIFF=0:It is single-ended 16-bit conversion..; when DIFF=1, it is differential 16-bit conversion with 2's complement output #11 ADLSMP Sample Time Configuration 4 1 read-write 0 Short sample time. #0 1 Long sample time. #1 ADIV Clock Divide Select 5 2 read-write 00 The divide ratio is 1 and the clock rate is input clock. #00 01 The divide ratio is 2 and the clock rate is (input clock)/2. #01 10 The divide ratio is 4 and the clock rate is (input clock)/4. #10 11 The divide ratio is 8 and the clock rate is (input clock)/8. #11 ADLPC Low-Power Configuration 7 1 read-write 0 Normal power configuration. #0 1 Low-power configuration. The power is reduced at the expense of maximum clock speed. #1 CFG2 ADC Configuration Register 2 0xC 32 read-write 0 0xFFFFFFFF ADLSTS Long Sample Time Select 0 2 read-write 00 Default longest sample time; 20 extra ADCK cycles; 24 ADCK cycles total. #00 01 12 extra ADCK cycles; 16 ADCK cycles total sample time. #01 10 6 extra ADCK cycles; 10 ADCK cycles total sample time. #10 11 2 extra ADCK cycles; 6 ADCK cycles total sample time. #11 ADHSC High-Speed Configuration 2 1 read-write 0 Normal conversion sequence selected. #0 1 High-speed conversion sequence selected with 2 additional ADCK cycles to total conversion time. #1 ADACKEN Asynchronous Clock Output Enable 3 1 read-write 0 Asynchronous clock output disabled; Asynchronous clock is enabled only if selected by ADICLK and a conversion is active. #0 1 Asynchronous clock and clock output is enabled regardless of the state of the ADC. #1 MUXSEL ADC Mux Select 4 1 read-write 0 ADxxa channels are selected. #0 1 ADxxb channels are selected. #1 2 0x4 A,B R%s ADC Data Result Register 0x10 32 read-only 0 0xFFFFFFFF D Data result 0 16 read-only 2 0x4 1,2 CV%s Compare Value Registers 0x18 32 read-write 0 0xFFFFFFFF CV Compare Value. 0 16 read-write SC2 Status and Control Register 2 0x20 32 read-write 0 0xFFFFFFFF REFSEL Voltage Reference Selection 0 2 read-write 00 Default voltage reference pin pair, that is, external pins VREFH and VREFL #00 01 Alternate reference pair, that is, VALTH and VALTL . This pair may be additional external pins or internal sources depending on the MCU configuration. See the chip configuration information for details specific to this MCU #01 DMAEN DMA Enable 2 1 read-write 0 DMA is disabled. #0 1 DMA is enabled and will assert the ADC DMA request during an ADC conversion complete event noted when any of the SC1n[COCO] flags is asserted. #1 ACREN Compare Function Range Enable 3 1 read-write 0 Range function disabled. Only CV1 is compared. #0 1 Range function enabled. Both CV1 and CV2 are compared. #1 ACFGT Compare Function Greater Than Enable 4 1 read-write 0 Configures less than threshold, outside range not inclusive and inside range not inclusive; functionality based on the values placed in CV1 and CV2. #0 1 Configures greater than or equal to threshold, outside and inside ranges inclusive; functionality based on the values placed in CV1 and CV2. #1 ACFE Compare Function Enable 5 1 read-write 0 Compare function disabled. #0 1 Compare function enabled. #1 ADTRG Conversion Trigger Select 6 1 read-write 0 Software trigger selected. #0 1 Hardware trigger selected. #1 ADACT Conversion Active 7 1 read-only 0 Conversion not in progress. #0 1 Conversion in progress. #1 SC3 Status and Control Register 3 0x24 32 read-write 0 0xFFFFFFFF AVGS Hardware Average Select 0 2 read-write 00 4 samples averaged. #00 01 8 samples averaged. #01 10 16 samples averaged. #10 11 32 samples averaged. #11 AVGE Hardware Average Enable 2 1 read-write 0 Hardware average function disabled. #0 1 Hardware average function enabled. #1 ADCO Continuous Conversion Enable 3 1 read-write 0 One conversion or one set of conversions if the hardware average function is enabled, that is, AVGE=1, after initiating a conversion. #0 1 Continuous conversions or sets of conversions if the hardware average function is enabled, that is, AVGE=1, after initiating a conversion. #1 CALF Calibration Failed Flag 6 1 read-write 0 Calibration completed normally. #0 1 Calibration failed. ADC accuracy specifications are not guaranteed. #1 CAL Calibration 7 1 read-write OFS ADC Offset Correction Register 0x28 32 read-write 0x4 0xFFFFFFFF OFS Offset Error Correction Value 0 16 read-write PG ADC Plus-Side Gain Register 0x2C 32 read-write 0x8200 0xFFFFFFFF PG Plus-Side Gain 0 16 read-write MG ADC Minus-Side Gain Register 0x30 32 read-write 0x8200 0xFFFFFFFF MG Minus-Side Gain 0 16 read-write CLPD ADC Plus-Side General Calibration Value Register 0x34 32 read-write 0xA 0xFFFFFFFF CLPD Calibration Value 0 6 read-write CLPS ADC Plus-Side General Calibration Value Register 0x38 32 read-write 0x20 0xFFFFFFFF CLPS Calibration Value 0 6 read-write CLP4 ADC Plus-Side General Calibration Value Register 0x3C 32 read-write 0x200 0xFFFFFFFF CLP4 Calibration Value 0 10 read-write CLP3 ADC Plus-Side General Calibration Value Register 0x40 32 read-write 0x100 0xFFFFFFFF CLP3 Calibration Value 0 9 read-write CLP2 ADC Plus-Side General Calibration Value Register 0x44 32 read-write 0x80 0xFFFFFFFF CLP2 Calibration Value 0 8 read-write CLP1 ADC Plus-Side General Calibration Value Register 0x48 32 read-write 0x40 0xFFFFFFFF CLP1 Calibration Value 0 7 read-write CLP0 ADC Plus-Side General Calibration Value Register 0x4C 32 read-write 0x20 0xFFFFFFFF CLP0 Calibration Value 0 6 read-write CLMD ADC Minus-Side General Calibration Value Register 0x54 32 read-write 0xA 0xFFFFFFFF CLMD Calibration Value 0 6 read-write CLMS ADC Minus-Side General Calibration Value Register 0x58 32 read-write 0x20 0xFFFFFFFF CLMS Calibration Value 0 6 read-write CLM4 ADC Minus-Side General Calibration Value Register 0x5C 32 read-write 0x200 0xFFFFFFFF CLM4 Calibration Value 0 10 read-write CLM3 ADC Minus-Side General Calibration Value Register 0x60 32 read-write 0x100 0xFFFFFFFF CLM3 Calibration Value 0 9 read-write CLM2 ADC Minus-Side General Calibration Value Register 0x64 32 read-write 0x80 0xFFFFFFFF CLM2 Calibration Value 0 8 read-write CLM1 ADC Minus-Side General Calibration Value Register 0x68 32 read-write 0x40 0xFFFFFFFF CLM1 Calibration Value 0 7 read-write CLM0 ADC Minus-Side General Calibration Value Register 0x6C 32 read-write 0x20 0xFFFFFFFF CLM0 Calibration Value 0 6 read-write RTC Secure Real Time Clock RTC_ 0x4003D000 0 0x20 registers RTC 20 RTC_Seconds 21 TSR RTC Time Seconds Register 0 32 read-write 0 0xFFFFFFFF TSR Time Seconds Register 0 32 read-write TPR RTC Time Prescaler Register 0x4 32 read-write 0 0xFFFFFFFF TPR Time Prescaler Register 0 16 read-write TAR RTC Time Alarm Register 0x8 32 read-write 0 0xFFFFFFFF TAR Time Alarm Register 0 32 read-write TCR RTC Time Compensation Register 0xC 32 read-write 0 0xFFFFFFFF TCR Time Compensation Register 0 8 read-write 10000000 Time Prescaler Register overflows every 32896 clock cycles. #10000000 11111111 Time Prescaler Register overflows every 32769 clock cycles. #11111111 0 Time Prescaler Register overflows every 32768 clock cycles. #0 1 Time Prescaler Register overflows every 32767 clock cycles. #1 1111111 Time Prescaler Register overflows every 32641 clock cycles. #1111111 CIR Compensation Interval Register 8 8 read-write TCV Time Compensation Value 16 8 read-only CIC Compensation Interval Counter 24 8 read-only CR RTC Control Register 0x10 32 read-write 0 0xFFFFFFFF SWR Software Reset 0 1 read-write 0 No effect. #0 1 Resets all RTC registers except for the SWR bit . The SWR bit is cleared by POR and by software explicitly clearing it. #1 WPE Wakeup Pin Enable 1 1 read-write 0 Wakeup pin is disabled. #0 1 Wakeup pin is enabled and wakeup pin asserts if the RTC interrupt asserts or the wakeup pin is turned on. #1 SUP Supervisor Access 2 1 read-write 0 Non-supervisor mode write accesses are not supported and generate a bus error. #0 1 Non-supervisor mode write accesses are supported. #1 UM Update Mode 3 1 read-write 0 Registers cannot be written when locked. #0 1 Registers can be written when locked under limited conditions. #1 WPS Wakeup Pin Select 4 1 read-write 0 Wakeup pin asserts (active low, open drain) if the RTC interrupt asserts or the wakeup pin is turned on. #0 1 Wakeup pin instead outputs the RTC 32kHz clock, provided the wakeup pin is turned on and the 32kHz clock is output to other peripherals. #1 OSCE Oscillator Enable 8 1 read-write 0 32.768 kHz oscillator is disabled. #0 1 32.768 kHz oscillator is enabled. After setting this bit, wait the oscillator startup time before enabling the time counter to allow the 32.768 kHz clock time to stabilize. #1 CLKO Clock Output 9 1 read-write 0 The 32 kHz clock is output to other peripherals. #0 1 The 32 kHz clock is not output to other peripherals. #1 SC16P Oscillator 16pF Load Configure 10 1 read-write 0 Disable the load. #0 1 Enable the additional load. #1 SC8P Oscillator 8pF Load Configure 11 1 read-write 0 Disable the load. #0 1 Enable the additional load. #1 SC4P Oscillator 4pF Load Configure 12 1 read-write 0 Disable the load. #0 1 Enable the additional load. #1 SC2P Oscillator 2pF Load Configure 13 1 read-write 0 Disable the load. #0 1 Enable the additional load. #1 SR RTC Status Register 0x14 32 read-write 0x1 0xFFFFFFFF TIF Time Invalid Flag 0 1 read-only 0 Time is valid. #0 1 Time is invalid and time counter is read as zero. #1 TOF Time Overflow Flag 1 1 read-only 0 Time overflow has not occurred. #0 1 Time overflow has occurred and time counter is read as zero. #1 TAF Time Alarm Flag 2 1 read-only 0 Time alarm has not occurred. #0 1 Time alarm has occurred. #1 TCE Time Counter Enable 4 1 read-write 0 Time counter is disabled. #0 1 Time counter is enabled. #1 LR RTC Lock Register 0x18 32 read-write 0xFF 0xFFFFFFFF TCL Time Compensation Lock 3 1 read-write 0 Time Compensation Register is locked and writes are ignored. #0 1 Time Compensation Register is not locked and writes complete as normal. #1 CRL Control Register Lock 4 1 read-write 0 Control Register is locked and writes are ignored. #0 1 Control Register is not locked and writes complete as normal. #1 SRL Status Register Lock 5 1 read-write 0 Status Register is locked and writes are ignored. #0 1 Status Register is not locked and writes complete as normal. #1 LRL Lock Register Lock 6 1 read-write 0 Lock Register is locked and writes are ignored. #0 1 Lock Register is not locked and writes complete as normal. #1 IER RTC Interrupt Enable Register 0x1C 32 read-write 0x7 0xFFFFFFFF TIIE Time Invalid Interrupt Enable 0 1 read-write 0 Time invalid flag does not generate an interrupt. #0 1 Time invalid flag does generate an interrupt. #1 TOIE Time Overflow Interrupt Enable 1 1 read-write 0 Time overflow flag does not generate an interrupt. #0 1 Time overflow flag does generate an interrupt. #1 TAIE Time Alarm Interrupt Enable 2 1 read-write 0 Time alarm flag does not generate an interrupt. #0 1 Time alarm flag does generate an interrupt. #1 TSIE Time Seconds Interrupt Enable 4 1 read-write 0 Seconds interrupt is disabled. #0 1 Seconds interrupt is enabled. #1 WPON Wakeup Pin On 7 1 read-write 0 No effect. #0 1 If the wakeup pin is enabled, then the wakeup pin will assert. #1 DAC0 12-Bit Digital-to-Analog Converter DAC0_ 0x4003F000 0 0x24 registers DAC0 25 2 0x2 0,1 DAT%sL DAC Data Low Register 0 8 read-write 0 0xFF DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write 2 0x2 0,1 DAT%sH DAC Data High Register 0x1 8 read-write 0 0xFF DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write SR DAC Status Register 0x20 8 read-write 0x2 0xFF DACBFRPBF DAC Buffer Read Pointer Bottom Position Flag 0 1 read-write 0 The DAC buffer read pointer is not equal to C2[DACBFUP]. #0 1 The DAC buffer read pointer is equal to C2[DACBFUP]. #1 DACBFRPTF DAC Buffer Read Pointer Top Position Flag 1 1 read-write 0 The DAC buffer read pointer is not zero. #0 1 The DAC buffer read pointer is zero. #1 C0 DAC Control Register 0x21 8 read-write 0 0xFF DACBBIEN DAC Buffer Read Pointer Bottom Flag Interrupt Enable 0 1 read-write 0 The DAC buffer read pointer bottom flag interrupt is disabled. #0 1 The DAC buffer read pointer bottom flag interrupt is enabled. #1 DACBTIEN DAC Buffer Read Pointer Top Flag Interrupt Enable 1 1 read-write 0 The DAC buffer read pointer top flag interrupt is disabled. #0 1 The DAC buffer read pointer top flag interrupt is enabled. #1 LPEN DAC Low Power Control 3 1 read-write 0 High-Power mode #0 1 Low-Power mode #1 DACSWTRG DAC Software Trigger 4 1 write-only 0 The DAC soft trigger is not valid. #0 1 The DAC soft trigger is valid. #1 DACTRGSEL DAC Trigger Select 5 1 read-write 0 The DAC hardware trigger is selected. #0 1 The DAC software trigger is selected. #1 DACRFS DAC Reference Select 6 1 read-write 0 The DAC selects DACREF_1 as the reference voltage. #0 1 The DAC selects DACREF_2 as the reference voltage. #1 DACEN DAC Enable 7 1 read-write 0 The DAC system is disabled. #0 1 The DAC system is enabled. #1 C1 DAC Control Register 1 0x22 8 read-write 0 0xFF DACBFEN DAC Buffer Enable 0 1 read-write 0 Buffer read pointer is disabled. The converted data is always the first word of the buffer. #0 1 Buffer read pointer is enabled. The converted data is the word that the read pointer points to. It means converted data can be from any word of the buffer. #1 DACBFMD DAC Buffer Work Mode Select 2 1 read-write 0 Normal mode #0 1 One-Time Scan mode #1 DMAEN DMA Enable Select 7 1 read-write 0 DMA is disabled. #0 1 DMA is enabled. When DMA is enabled, the DMA request will be generated by original interrupts. The interrupts will not be presented on this module at the same time. #1 C2 DAC Control Register 2 0x23 8 read-write 0x1 0xFF DACBFUP DAC Buffer Upper Limit 0 1 read-write DACBFRP DAC Buffer Read Pointer 4 1 read-write LPTMR0 Low Power Timer LPTMR0_ 0x40040000 0 0x10 registers LPTMR0 28 CSR Low Power Timer Control Status Register 0 32 read-write 0 0xFFFFFFFF TEN Timer Enable 0 1 read-write 0 LPTMR is disabled and internal logic is reset. #0 1 LPTMR is enabled. #1 TMS Timer Mode Select 1 1 read-write 0 Time Counter mode. #0 1 Pulse Counter mode. #1 TFC Timer Free-Running Counter 2 1 read-write 0 CNR is reset whenever TCF is set. #0 1 CNR is reset on overflow. #1 TPP Timer Pin Polarity 3 1 read-write 0 Pulse Counter input source is active-high, and the CNR will increment on the rising-edge. #0 1 Pulse Counter input source is active-low, and the CNR will increment on the falling-edge. #1 TPS Timer Pin Select 4 2 read-write 00 Pulse counter input 0 is selected. #00 01 Pulse counter input 1 is selected. #01 10 Pulse counter input 2 is selected. #10 11 Pulse counter input 3 is selected. #11 TIE Timer Interrupt Enable 6 1 read-write 0 Timer interrupt disabled. #0 1 Timer interrupt enabled. #1 TCF Timer Compare Flag 7 1 read-write 0 The value of CNR is not equal to CMR and increments. #0 1 The value of CNR is equal to CMR and increments. #1 PSR Low Power Timer Prescale Register 0x4 32 read-write 0 0xFFFFFFFF PCS Prescaler Clock Select 0 2 read-write 00 Prescaler/glitch filter clock 0 selected. #00 01 Prescaler/glitch filter clock 1 selected. #01 10 Prescaler/glitch filter clock 2 selected. #10 11 Prescaler/glitch filter clock 3 selected. #11 PBYP Prescaler Bypass 2 1 read-write 0 Prescaler/glitch filter is enabled. #0 1 Prescaler/glitch filter is bypassed. #1 PRESCALE Prescale Value 3 4 read-write 0000 Prescaler divides the prescaler clock by 2; glitch filter does not support this configuration. #0000 0001 Prescaler divides the prescaler clock by 4; glitch filter recognizes change on input pin after 2 rising clock edges. #0001 0010 Prescaler divides the prescaler clock by 8; glitch filter recognizes change on input pin after 4 rising clock edges. #0010 0011 Prescaler divides the prescaler clock by 16; glitch filter recognizes change on input pin after 8 rising clock edges. #0011 0100 Prescaler divides the prescaler clock by 32; glitch filter recognizes change on input pin after 16 rising clock edges. #0100 0101 Prescaler divides the prescaler clock by 64; glitch filter recognizes change on input pin after 32 rising clock edges. #0101 0110 Prescaler divides the prescaler clock by 128; glitch filter recognizes change on input pin after 64 rising clock edges. #0110 0111 Prescaler divides the prescaler clock by 256; glitch filter recognizes change on input pin after 128 rising clock edges. #0111 1000 Prescaler divides the prescaler clock by 512; glitch filter recognizes change on input pin after 256 rising clock edges. #1000 1001 Prescaler divides the prescaler clock by 1024; glitch filter recognizes change on input pin after 512 rising clock edges. #1001 1010 Prescaler divides the prescaler clock by 2048; glitch filter recognizes change on input pin after 1024 rising clock edges. #1010 1011 Prescaler divides the prescaler clock by 4096; glitch filter recognizes change on input pin after 2048 rising clock edges. #1011 1100 Prescaler divides the prescaler clock by 8192; glitch filter recognizes change on input pin after 4096 rising clock edges. #1100 1101 Prescaler divides the prescaler clock by 16,384; glitch filter recognizes change on input pin after 8192 rising clock edges. #1101 1110 Prescaler divides the prescaler clock by 32,768; glitch filter recognizes change on input pin after 16,384 rising clock edges. #1110 1111 Prescaler divides the prescaler clock by 65,536; glitch filter recognizes change on input pin after 32,768 rising clock edges. #1111 CMR Low Power Timer Compare Register 0x8 32 read-write 0 0xFFFFFFFF COMPARE Compare Value 0 16 read-write CNR Low Power Timer Counter Register 0xC 32 read-write 0 0xFFFFFFFF COUNTER Counter Value 0 16 read-write TSI0 Touch sense input TSI0_ 0x40045000 0 0xC registers TSI0 26 GENCS TSI General Control and Status Register 0 32 read-write 0 0xFFFFFFFF CURSW CURSW 1 1 read-write 0 The current source pair are not swapped. #0 1 The current source pair are swapped. #1 EOSF End of Scan Flag 2 1 read-write 0 Scan not complete. #0 1 Scan complete. #1 SCNIP Scan In Progress Status 3 1 read-only 0 No scan in progress. #0 1 Scan in progress. #1 STM Scan Trigger Mode 4 1 read-write 0 Software trigger scan. #0 1 Hardware trigger scan. #1 STPE TSI STOP Enable 5 1 read-write 0 TSI is disabled when MCU goes into low power mode. #0 1 Allows TSI to continue running in all low power modes. #1 TSIIEN Touch Sensing Input Interrupt Enable 6 1 read-write 0 TSI interrupt is disabled. #0 1 TSI interrupt is enabled. #1 TSIEN Touch Sensing Input Module Enable 7 1 read-write 0 TSI module disabled. #0 1 TSI module enabled. #1 NSCN NSCN 8 5 read-write 00000 Once per electrode #00000 00001 Twice per electrode #00001 00010 3 times per electrode #00010 00011 4 times per electrode #00011 00100 5 times per electrode #00100 00101 6 times per electrode #00101 00110 7 times per electrode #00110 00111 8 times per electrode #00111 01000 9 times per electrode #01000 01001 10 times per electrode #01001 01010 11 times per electrode #01010 01011 12 times per electrode #01011 01100 13 times per electrode #01100 01101 14 times per electrode #01101 01110 15 times per electrode #01110 01111 16 times per electrode #01111 10000 17 times per electrode #10000 10001 18 times per electrode #10001 10010 19 times per electrode #10010 10011 20 times per electrode #10011 10100 21 times per electrode #10100 10101 22 times per electrode #10101 10110 23 times per electrode #10110 10111 24 times per electrode #10111 11000 25 times per electrode #11000 11001 26 times per electrode #11001 11010 27 times per electrode #11010 11011 28 times per electrode #11011 11100 29 times per electrode #11100 11101 30 times per electrode #11101 11110 31 times per electrode #11110 11111 32 times per electrode #11111 PS PS 13 3 read-write 000 Electrode Oscillator Frequency divided by 1 #000 001 Electrode Oscillator Frequency divided by 2 #001 010 Electrode Oscillator Frequency divided by 4 #010 011 Electrode Oscillator Frequency divided by 8 #011 100 Electrode Oscillator Frequency divided by 16 #100 101 Electrode Oscillator Frequency divided by 32 #101 110 Electrode Oscillator Frequency divided by 64 #110 111 Electrode Oscillator Frequency divided by 128 #111 EXTCHRG EXTCHRG 16 3 read-write 000 500 nA. #000 001 1 uA. #001 010 2 uA. #010 011 4 uA. #011 100 8 uA. #100 101 16 uA. #101 110 32 uA. #110 111 64 uA. #111 DVOLT DVOLT 19 2 read-write 00 DV = 1.03 V; VP = 1.33 V; Vm = 0.30 V. #00 01 DV = 0.73 V; VP = 1.18 V; Vm = 0.45 V. #01 10 DV = 0.43 V; VP = 1.03 V; Vm = 0.60 V. #10 11 DV = 0.29 V; VP = 0.95 V; Vm = 0.67 V. #11 REFCHRG REFCHRG 21 3 read-write 000 500 nA. #000 001 1 uA. #001 010 2 uA. #010 011 4 uA. #011 100 8 uA. #100 101 16 uA. #101 110 32 uA. #110 111 64 uA. #111 MODE TSI analog modes setup and status bits. 24 4 read-write 0000 Set TSI in capacitive sensing(non-noise detection) mode. #0000 0100 Set TSI analog to work in single threshold noise detection mode and the frequency limitation circuit is disabled. #0100 1000 Set TSI analog to work in single threshold noise detection mode and the frequency limitation circuit is enabled to work in higher frequencies operations. #1000 1100 Set TSI analog to work in automatic noise detection mode. #1100 ESOR End-of-scan or Out-of-Range Interrupt Selection 28 1 read-write 0 Out-of-range interrupt is allowed. #0 1 End-of-scan interrupt is allowed. #1 OUTRGF Out of Range Flag. 31 1 read-write DATA TSI DATA Register 0x4 32 read-write 0 0xFFFFFFFF TSICNT TSI Conversion Counter Value 0 16 read-only SWTS Software Trigger Start 22 1 write-only 0 No effect. #0 1 Start a scan to determine which channel is specified by TSI_DATA[TSICH]. #1 DMAEN DMA Transfer Enabled 23 1 read-write 0 Interrupt is selected when the interrupt enable bit is set and the corresponding TSI events assert. #0 1 DMA transfer request is selected when the interrupt enable bit is set and the corresponding TSI events assert. #1 TSICH TSICH 28 4 read-write 0000 Channel 0. #0000 0001 Channel 1. #0001 0010 Channel 2. #0010 0011 Channel 3. #0011 0100 Channel 4. #0100 0101 Channel 5. #0101 0110 Channel 6. #0110 0111 Channel 7. #0111 1000 Channel 8. #1000 1001 Channel 9. #1001 1010 Channel 10. #1010 1011 Channel 11. #1011 1100 Channel 12. #1100 1101 Channel 13. #1101 1110 Channel 14. #1110 1111 Channel 15. #1111 TSHD TSI Threshold Register 0x8 32 read-write 0 0xFFFFFFFF THRESL TSI Wakeup Channel Low-threshold 0 16 read-write THRESH TSI Wakeup Channel High-threshold 16 16 read-write SIM System Integration Module SIM_ 0x40047000 0 0x1108 registers SOPT1 System Options Register 1 0 32 read-write 0x80000000 0xFFFFFFFF OSC32KSEL 32K Oscillator Clock Select 18 2 read-write 00 System oscillator (OSC32KCLK) #00 10 RTC_CLKIN #10 11 LPO 1kHz #11 SOPT1CFG SOPT1 Configuration Register 0x4 32 read-write 0 0xFFFFFFFF SOPT2 System Options Register 2 0x1004 32 read-write 0 0xFFFFFFFF RTCCLKOUTSEL RTC Clock Out Select 4 1 read-write 0 RTC 1 Hz clock is output on the RTC_CLKOUT pin. #0 1 OSCERCLK clock is output on the RTC_CLKOUT pin. #1 CLKOUTSEL CLKOUT select 5 3 read-write 010 Bus clock #010 011 LPO clock (1 kHz) #011 100 MCGIRCLK #100 110 OSCERCLK #110 PLLFLLSEL PLL/FLL clock select 16 1 read-write 0 MCGFLLCLK clock #0 1 MCGPLLCLK clock with fixed divide by 2 #1 TPMSRC TPM Clock Source Select 24 2 read-write 00 Clock disabled #00 01 MCGFLLCLK clock , or MCGPLLCLK/2 #01 10 OSCERCLK clock #10 11 MCGIRCLK clock #11 UART0SRC UART0 Clock Source Select 26 2 read-write 00 Clock disabled #00 01 MCGFLLCLK clock , or MCGPLLCLK/2 #01 10 OSCERCLK clock #10 11 MCGIRCLK clock #11 SOPT4 System Options Register 4 0x100C 32 read-write 0 0xFFFFFFFF TPM1CH0SRC TPM1 channel 0 input capture source select 18 2 read-write 00 TPM1_CH0 signal #00 01 CMP0 output #01 TPM2CH0SRC TPM2 Channel 0 Input Capture Source Select 20 1 read-write 0 TPM2_CH0 signal #0 1 CMP0 output #1 TPM0CLKSEL TPM0 External Clock Pin Select 24 1 read-write 0 TPM0 external clock driven by TPM_CLKIN0 pin. #0 1 TPM0 external clock driven by TPM_CLKIN1 pin. #1 TPM1CLKSEL TPM1 External Clock Pin Select 25 1 read-write 0 TPM1 external clock driven by TPM_CLKIN0 pin. #0 1 TPM1 external clock driven by TPM_CLKIN1 pin. #1 TPM2CLKSEL TPM2 External Clock Pin Select 26 1 read-write 0 TPM2 external clock driven by TPM_CLKIN0 pin. #0 1 TPM2 external clock driven by TPM_CLKIN1 pin. #1 SOPT5 System Options Register 5 0x1010 32 read-write 0 0xFFFFFFFF UART0TXSRC UART0 Transmit Data Source Select 0 2 read-write 00 UART0_TX pin #00 01 UART0_TX pin modulated with TPM1 channel 0 output #01 10 UART0_TX pin modulated with TPM2 channel 0 output #10 UART0RXSRC UART0 Receive Data Source Select 2 1 read-write 0 UART_RX pin #0 1 CMP0 output #1 UART1TXSRC UART1 Transmit Data Source Select 4 2 read-write 00 UART1_TX pin #00 01 UART1_TX pin modulated with TPM1 channel 0 output #01 10 UART1_TX pin modulated with TPM2 channel 0 output #10 UART1RXSRC UART1 Receive Data Source Select 6 1 read-write 0 UART1_RX pin #0 1 CMP0 output #1 UART0ODE UART0 Open Drain Enable 16 1 read-write 0 Open drain is disabled on UART0. #0 1 Open drain is enabled on UART0. #1 UART1ODE UART1 Open Drain Enable 17 1 read-write 0 Open drain is disabled on UART1. #0 1 Open drain is enabled on UART1 #1 UART2ODE UART2 Open Drain Enable 18 1 read-write 0 Open drain is disabled on UART2 #0 1 Open drain is enabled on UART2 #1 SOPT7 System Options Register 7 0x1018 32 read-write 0 0xFFFFFFFF ADC0TRGSEL ADC0 Trigger Select 0 4 read-write 0000 External trigger pin input (EXTRG_IN) #0000 0001 CMP0 output #0001 0100 PIT trigger 0 #0100 0101 PIT trigger 1 #0101 1000 TPM0 overflow #1000 1001 TPM1 overflow #1001 1010 TPM2 overflow #1010 1100 RTC alarm #1100 1101 RTC seconds #1101 1110 LPTMR0 trigger #1110 ADC0PRETRGSEL ADC0 Pretrigger Select 4 1 read-write 0 Pre-trigger A #0 1 Pre-trigger B #1 ADC0ALTTRGEN ADC0 Alternate Trigger Enable 7 1 read-write 0 TPM1 channel 0 (A) and channel 1 (B) triggers selected for ADC0. #0 1 Alternate trigger selected for ADC0. #1 SDID System Device Identification Register 0x1024 32 read-only 0x100500 0xFFFFFFFF PINID Pincount Identification 0 4 read-only 0000 16-pin #0000 0001 24-pin #0001 0010 32-pin #0010 0011 36-pin #0011 0100 48-pin #0100 0101 64-pin #0101 0110 80-pin #0110 1000 100-pin #1000 1011 Custom pinout (WLCSP) #1011 DIEID Device Die Number 7 5 read-only REVID Device Revision Number 12 4 read-only SRAMSIZE System SRAM Size 16 4 read-only 0000 0.5 KB #0000 0001 1 KB #0001 0010 2 KB #0010 0011 4 KB #0011 0100 8 KB #0100 0101 16 KB #0101 0110 32 KB #0110 0111 64 KB #0111 SERIESID Kinetis Series ID 20 4 read-only 0001 KL family #0001 SUBFAMID Kinetis Sub-Family ID 24 4 read-only 0010 KLx2 Subfamily #0010 0011 KLx3 Subfamily #0011 0100 KLx4 Subfamily #0100 0101 KLx5 Subfamily #0101 0110 KLx6 Subfamily #0110 0111 KLx7 Subfamily #0111 FAMID Kinetis family ID 28 4 read-only 0000 KL0x Family (low end) #0000 0001 KL1x Family (basic) #0001 0010 KL2x Family (USB) #0010 0011 KL3x Family (Segment LCD) #0011 0100 KL4x Family (USB and Segment LCD) #0100 SCGC4 System Clock Gating Control Register 4 0x1034 32 read-write 0xF0000030 0xFFFFFFFF I2C0 I2C0 Clock Gate Control 6 1 read-write 0 Clock disabled #0 1 Clock enabled #1 I2C1 I2C1 Clock Gate Control 7 1 read-write 0 Clock disabled #0 1 Clock enabled #1 UART0 UART0 Clock Gate Control 10 1 read-write 0 Clock disabled #0 1 Clock enabled #1 UART1 UART1 Clock Gate Control 11 1 read-write 0 Clock disabled #0 1 Clock enabled #1 UART2 UART2 Clock Gate Control 12 1 read-write 0 Clock disabled #0 1 Clock enabled #1 CMP Comparator Clock Gate Control 19 1 read-write 0 Clock disabled #0 1 Clock enabled #1 SPI0 SPI0 Clock Gate Control 22 1 read-write 0 Clock disabled #0 1 Clock enabled #1 SPI1 SPI1 Clock Gate Control 23 1 read-write 0 Clock disabled #0 1 Clock enabled #1 SCGC5 System Clock Gating Control Register 5 0x1038 32 read-write 0x182 0xFFFFFFFF LPTMR Low Power Timer Access Control 0 1 read-write 0 Access disabled #0 1 Access enabled #1 TSI TSI Access Control 5 1 read-write 0 Access disabled #0 1 Access enabled #1 PORTA Port A Clock Gate Control 9 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PORTB Port B Clock Gate Control 10 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PORTC Port C Clock Gate Control 11 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PORTD Port D Clock Gate Control 12 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PORTE Port E Clock Gate Control 13 1 read-write 0 Clock disabled #0 1 Clock enabled #1 SLCD Segment LCD Clock Gate Control 19 1 read-write 0 Clock disabled #0 1 Clock enabled #1 SCGC6 System Clock Gating Control Register 6 0x103C 32 read-write 0x1 0xFFFFFFFF FTF Flash Memory Clock Gate Control 0 1 read-write 0 Clock disabled #0 1 Clock enabled #1 DMAMUX DMA Mux Clock Gate Control 1 1 read-write 0 Clock disabled #0 1 Clock enabled #1 I2S I2S Clock Gate Control 15 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PIT PIT Clock Gate Control 23 1 read-write 0 Clock disabled #0 1 Clock enabled #1 TPM0 TPM0 Clock Gate Control 24 1 read-write 0 Clock disabled #0 1 Clock enabled #1 TPM1 TPM1 Clock Gate Control 25 1 read-write 0 Clock disabled #0 1 Clock enabled #1 TPM2 TPM2 Clock Gate Control 26 1 read-write 0 Clock disabled #0 1 Clock enabled #1 ADC0 ADC0 Clock Gate Control 27 1 read-write 0 Clock disabled #0 1 Clock enabled #1 RTC RTC Access Control 29 1 read-write 0 Access and interrupts disabled #0 1 Access and interrupts enabled #1 DAC0 DAC0 Clock Gate Control 31 1 read-write 0 Clock disabled #0 1 Clock enabled #1 SCGC7 System Clock Gating Control Register 7 0x1040 32 read-write 0x100 0xFFFFFFFF DMA DMA Clock Gate Control 8 1 read-write 0 Clock disabled #0 1 Clock enabled #1 CLKDIV1 System Clock Divider Register 1 0x1044 32 read-write 0x10000 0xFFFFFFFF OUTDIV4 Clock 4 Output Divider value 16 3 read-write 000 Divide-by-1. #000 001 Divide-by-2. #001 010 Divide-by-3. #010 011 Divide-by-4. #011 100 Divide-by-5. #100 101 Divide-by-6. #101 110 Divide-by-7. #110 111 Divide-by-8. #111 OUTDIV1 Clock 1 Output Divider value 28 4 read-write 0000 Divide-by-1. #0000 0001 Divide-by-2. #0001 0010 Divide-by-3. #0010 0011 Divide-by-4. #0011 0100 Divide-by-5. #0100 0101 Divide-by-6. #0101 0110 Divide-by-7. #0110 0111 Divide-by-8. #0111 1000 Divide-by-9. #1000 1001 Divide-by-10. #1001 1010 Divide-by-11. #1010 1011 Divide-by-12. #1011 1100 Divide-by-13. #1100 1101 Divide-by-14. #1101 1110 Divide-by-15. #1110 1111 Divide-by-16. #1111 FCFG1 Flash Configuration Register 1 0x104C 32 read-write 0xF000000 0xFFFFFFFF FLASHDIS Flash Disable 0 1 read-write 0 Flash is enabled. #0 1 Flash is disabled. #1 FLASHDOZE Flash Doze 1 1 read-write 0 Flash remains enabled during Doze mode. #0 1 Flash is disabled for the duration of Doze mode. #1 PFSIZE Program Flash Size 24 4 read-only 0000 8 KB of program flash memory, 0.25 KB protection region #0000 0001 16 KB of program flash memory, 0.5 KB protection region #0001 0011 32 KB of program flash memory, 1 KB protection region #0011 0101 64 KB of program flash memory, 2 KB protection region #0101 0111 128 KB of program flash memory, 4 KB protection region #0111 1001 256 KB of program flash memory, 8 KB protection region #1001 1111 128 KB of program flash memory, 4 KB protection region 256 KB of program flash memory, 8 KB protection region #1111 FCFG2 Flash Configuration Register 2 0x1050 32 read-only 0x7FFF0000 0xFFFFFFFF MAXADDR1 This field concatenated with leading zeros plus the value of the MAXADDR1 field indicates the first invalid address of the second program flash block (flash block 1) 16 7 read-only MAXADDR0 Max Address lock 24 7 read-only UIDMH Unique Identification Register Mid-High 0x1058 32 read-only 0 0xFFFFFFFF UID Unique Identification 0 16 read-only UIDML Unique Identification Register Mid Low 0x105C 32 read-only 0 0xFFFFFFFF UID Unique Identification 0 32 read-only UIDL Unique Identification Register Low 0x1060 32 read-only 0 0xFFFFFFFF UID Unique Identification 0 32 read-only COPC COP Control Register 0x1100 32 read-write 0xC 0xFFFFFFFF COPW COP Windowed Mode 0 1 read-write 0 Normal mode #0 1 Windowed mode #1 COPCLKS COP Clock Select 1 1 read-write 0 Internal 1 kHz clock is source to COP. #0 1 Bus clock is source to COP. #1 COPT COP Watchdog Timeout 2 2 read-write 00 COP disabled #00 01 COP timeout after 25 LPO cycles or 213 bus clock cycles #01 10 COP timeout after 28 LPO cycles or 216 bus clock cycles #10 11 COP timeout after 210 LPO cycles or 218 bus clock cycles #11 SRVCOP Service COP 0x1104 32 write-only 0 0xFFFFFFFF SRVCOP Service COP Register 0 8 write-only PORTA Pin Control and Interrupts PORT PORTA_ 0x40049000 0 0xA4 registers PORTA 30 PCR0 Pin Control Register n 0 32 read-write 0x706 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR1 Pin Control Register n 0x4 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR2 Pin Control Register n 0x8 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR3 Pin Control Register n 0xC 32 read-write 0x703 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR4 Pin Control Register n 0x10 32 read-write 0x707 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR5 Pin Control Register n 0x14 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR6 Pin Control Register n 0x18 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR7 Pin Control Register n 0x1C 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR8 Pin Control Register n 0x20 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR9 Pin Control Register n 0x24 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR10 Pin Control Register n 0x28 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR11 Pin Control Register n 0x2C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR12 Pin Control Register n 0x30 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR13 Pin Control Register n 0x34 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR14 Pin Control Register n 0x38 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR15 Pin Control Register n 0x3C 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR16 Pin Control Register n 0x40 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR17 Pin Control Register n 0x44 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR18 Pin Control Register n 0x48 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR19 Pin Control Register n 0x4C 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR20 Pin Control Register n 0x50 32 read-write 0x717 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR21 Pin Control Register n 0x54 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR22 Pin Control Register n 0x58 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR23 Pin Control Register n 0x5C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR24 Pin Control Register n 0x60 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR25 Pin Control Register n 0x64 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR26 Pin Control Register n 0x68 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR27 Pin Control Register n 0x6C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR28 Pin Control Register n 0x70 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR29 Pin Control Register n 0x74 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR30 Pin Control Register n 0x78 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR31 Pin Control Register n 0x7C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCHR Global Pin Control High Register 0x84 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write 0 0xFFFFFFFF ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PORTB Pin Control and Interrupts PORT PORTB_ 0x4004A000 0 0xA4 registers PCR0 Pin Control Register n 0 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR1 Pin Control Register n 0x4 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR2 Pin Control Register n 0x8 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR3 Pin Control Register n 0xC 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR4 Pin Control Register n 0x10 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR5 Pin Control Register n 0x14 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR6 Pin Control Register n 0x18 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR7 Pin Control Register n 0x1C 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR8 Pin Control Register n 0x20 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR9 Pin Control Register n 0x24 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR10 Pin Control Register n 0x28 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR11 Pin Control Register n 0x2C 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR12 Pin Control Register n 0x30 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR13 Pin Control Register n 0x34 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR14 Pin Control Register n 0x38 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR15 Pin Control Register n 0x3C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR16 Pin Control Register n 0x40 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR17 Pin Control Register n 0x44 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR18 Pin Control Register n 0x48 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR19 Pin Control Register n 0x4C 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR20 Pin Control Register n 0x50 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR21 Pin Control Register n 0x54 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR22 Pin Control Register n 0x58 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR23 Pin Control Register n 0x5C 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR24 Pin Control Register n 0x60 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR25 Pin Control Register n 0x64 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR26 Pin Control Register n 0x68 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR27 Pin Control Register n 0x6C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR28 Pin Control Register n 0x70 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR29 Pin Control Register n 0x74 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR30 Pin Control Register n 0x78 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR31 Pin Control Register n 0x7C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCHR Global Pin Control High Register 0x84 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write 0 0xFFFFFFFF ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PORTC Pin Control and Interrupts PORT PORTC_ 0x4004B000 0 0xA4 registers PORTC_PORTD 31 PCR0 Pin Control Register n 0 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR1 Pin Control Register n 0x4 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR2 Pin Control Register n 0x8 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR3 Pin Control Register n 0xC 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR4 Pin Control Register n 0x10 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR5 Pin Control Register n 0x14 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR6 Pin Control Register n 0x18 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR7 Pin Control Register n 0x1C 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR8 Pin Control Register n 0x20 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR9 Pin Control Register n 0x24 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR10 Pin Control Register n 0x28 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR11 Pin Control Register n 0x2C 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR12 Pin Control Register n 0x30 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR13 Pin Control Register n 0x34 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR14 Pin Control Register n 0x38 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR15 Pin Control Register n 0x3C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR16 Pin Control Register n 0x40 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR17 Pin Control Register n 0x44 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR18 Pin Control Register n 0x48 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR19 Pin Control Register n 0x4C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR20 Pin Control Register n 0x50 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR21 Pin Control Register n 0x54 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR22 Pin Control Register n 0x58 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR23 Pin Control Register n 0x5C 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR24 Pin Control Register n 0x60 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR25 Pin Control Register n 0x64 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR26 Pin Control Register n 0x68 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR27 Pin Control Register n 0x6C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR28 Pin Control Register n 0x70 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR29 Pin Control Register n 0x74 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR30 Pin Control Register n 0x78 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR31 Pin Control Register n 0x7C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCHR Global Pin Control High Register 0x84 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write 0 0xFFFFFFFF ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PORTD Pin Control and Interrupts PORT PORTD_ 0x4004C000 0 0xA4 registers PORTC_PORTD 31 PCR0 Pin Control Register n 0 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR1 Pin Control Register n 0x4 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR2 Pin Control Register n 0x8 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR3 Pin Control Register n 0xC 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR4 Pin Control Register n 0x10 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR5 Pin Control Register n 0x14 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR6 Pin Control Register n 0x18 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR7 Pin Control Register n 0x1C 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR8 Pin Control Register n 0x20 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR9 Pin Control Register n 0x24 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR10 Pin Control Register n 0x28 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR11 Pin Control Register n 0x2C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR12 Pin Control Register n 0x30 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR13 Pin Control Register n 0x34 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR14 Pin Control Register n 0x38 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR15 Pin Control Register n 0x3C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR16 Pin Control Register n 0x40 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR17 Pin Control Register n 0x44 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR18 Pin Control Register n 0x48 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR19 Pin Control Register n 0x4C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR20 Pin Control Register n 0x50 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR21 Pin Control Register n 0x54 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR22 Pin Control Register n 0x58 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR23 Pin Control Register n 0x5C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR24 Pin Control Register n 0x60 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR25 Pin Control Register n 0x64 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR26 Pin Control Register n 0x68 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR27 Pin Control Register n 0x6C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR28 Pin Control Register n 0x70 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR29 Pin Control Register n 0x74 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR30 Pin Control Register n 0x78 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR31 Pin Control Register n 0x7C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCHR Global Pin Control High Register 0x84 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write 0 0xFFFFFFFF ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PORTE Pin Control and Interrupts PORT PORTE_ 0x4004D000 0 0xA4 registers PCR0 Pin Control Register n 0 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR1 Pin Control Register n 0x4 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR2 Pin Control Register n 0x8 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR3 Pin Control Register n 0xC 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR4 Pin Control Register n 0x10 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR5 Pin Control Register n 0x14 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR6 Pin Control Register n 0x18 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR7 Pin Control Register n 0x1C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR8 Pin Control Register n 0x20 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR9 Pin Control Register n 0x24 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR10 Pin Control Register n 0x28 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR11 Pin Control Register n 0x2C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR12 Pin Control Register n 0x30 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR13 Pin Control Register n 0x34 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR14 Pin Control Register n 0x38 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR15 Pin Control Register n 0x3C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR16 Pin Control Register n 0x40 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR17 Pin Control Register n 0x44 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR18 Pin Control Register n 0x48 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR19 Pin Control Register n 0x4C 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR20 Pin Control Register n 0x50 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR21 Pin Control Register n 0x54 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR22 Pin Control Register n 0x58 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR23 Pin Control Register n 0x5C 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR24 Pin Control Register n 0x60 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR25 Pin Control Register n 0x64 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR26 Pin Control Register n 0x68 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR27 Pin Control Register n 0x6C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR28 Pin Control Register n 0x70 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR29 Pin Control Register n 0x74 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR30 Pin Control Register n 0x78 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR31 Pin Control Register n 0x7C 32 read-write 0x5 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCHR Global Pin Control High Register 0x84 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write 0 0xFFFFFFFF ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LCD Segment Liquid Crystal Display LCD_ 0x40053000 0 0x60 registers LCD 29 GCR LCD General Control Register 0 32 read-write 0x8300003 0xFFFFFFFF DUTY LCD duty select 0 3 read-write 000 Use 1 BP (1/1 duty cycle). #000 001 Use 2 BP (1/2 duty cycle). #001 010 Use 3 BP (1/3 duty cycle). #010 011 Use 4 BP (1/4 duty cycle). (Default) #011 111 Use 8 BP (1/8 duty cycle). #111 LCLK LCD Clock Prescaler 3 3 read-write SOURCE LCD Clock Source Select 6 1 read-write 0 Selects the default clock as the LCD clock source. #0 1 Selects output of the alternate clock source selection (see ALTSOURCE) as the LCD clock source. #1 LCDEN LCD Driver Enable 7 1 read-write 0 All front plane and back plane pins are disabled. The LCD controller system is also disabled, and all LCD waveform generation clocks are stopped. V LL3 is connected to V DD internally. All LCD pins, LCD_Pn, enabled using the LCD Pin Enable register, output a low value. #0 1 LCD controller driver system is enabled, and front plane and back plane waveforms are generated. All LCD pins, LCD_Pn, enabled if PAD_SAFE is clearusing the LCD Pin Enable register, output an LCD driver waveform. The back plane pins output an LCD driver back plane waveform based on the settings of DUTY[2:0]. Charge pump or resistor bias is enabled. #1 LCDSTP LCD Stop 8 1 read-write 0 Allows the LCD driver, charge pump, resistor bias network, and voltage regulator to continue running during Stop mode. #0 1 Disables the LCD driver, charge pump, resistor bias network, and voltage regulator when MCU enters Stop mode. #1 LCDDOZE LCD Doze enable 9 1 read-write 0 Allows the LCD driver, charge pump, resistor bias network, and voltage regulator to continue running during Doze mode. #0 1 Disables the LCD driver, charge pump, resistor bias network, and voltage regulator when MCU enters Doze mode. #1 FFR Fast Frame Rate Select 10 1 read-write 0 Standard Frame Rate LCD Frame Freq: 23.3 (min) 73.1 (max) #0 1 Fast Frame Rate (Standard Frame Rate x2) LCD Frame Freq: 46.6 (min) 146.2 (max) #1 ALTSOURCE Selects the alternate clock source 11 1 read-write 0 Select Alternate Clock Source 1 (default) #0 1 Select Alternate Clock Source 2 #1 ALTDIV LCD AlternateClock Divider 12 2 read-write 0 Divide factor = 1 (No divide) #00 1 Divide factor = 8 #01 10 Divide factor = 64 #10 11 Divide factor = 512 #11 FDCIEN LCD Fault Detection Complete Interrupt Enable 14 1 read-write 0 No interrupt request is generated by this event. #0 1 When a fault is detected and FDCF bit is set, this event causes an interrupt request. #1 PADSAFE Pad Safe State Enable 15 1 read-write 0 LCD frontplane and backplane functions enabled according to other LCD control bits #0 1 LCD frontplane and backplane functions disabled #1 VSUPPLY Voltage Supply Control 17 1 read-write 0 Drive VLL3 internally from VDD #0 1 Drive VLL3 externally from VDD or drive VLL internally from vIREG #1 LADJ Load Adjust 20 2 read-write CPSEL Charge Pump or Resistor Bias Select 23 1 read-write 0 LCD charge pump is disabled. Resistor network selected. (The internal 1/3-bias is forced.) #0 1 LCD charge pump is selected. Resistor network disabled. (The internal 1/3-bias is forced.) #1 RVTRIM Regulated Voltage Trim 24 4 read-write RVEN Regulated Voltage Enable 31 1 read-write 0 Regulated voltage disabled. #0 1 Regulated voltage enabled. #1 AR LCD Auxiliary Register 0x4 32 read-write 0 0xFFFFFFFF BRATE Blink-rate configuration 0 3 read-write BMODE Blink mode 3 1 read-write 0 Display blank during the blink period. #0 1 Display alternate display during blink period (Ignored if duty is 5 or greater). #1 BLANK Blank display mode 5 1 read-write 0 Normal or alternate display mode. #0 1 Blank display mode. #1 ALT Alternate display mode 6 1 read-write 0 Normal display mode. #0 1 Alternate display mode. #1 BLINK Blink command 7 1 read-write 0 Disables blinking. #0 1 Starts blinking at blinking frequency specified by LCD blink rate calculation. #1 FDCR LCD Fault Detect Control Register 0x8 32 read-write 0 0xFFFFFFFF FDPINID Fault Detect Pin ID 0 6 read-write 0 Fault detection for LCD_P0 pin. #0 1 Fault detection for LCD_P1 pin. #1 111111 Fault detection for LCD_P63 pin. #111111 FDBPEN Fault Detect Back Plane Enable 6 1 read-write 0 Type of the selected pin under fault detect test is front plane. #0 1 Type of the selected pin under fault detect test is back plane. #1 FDEN Fault Detect Enable 7 1 read-write 0 Disable fault detection. #0 1 Enable fault detection. #1 FDSWW Fault Detect Sample Window Width 9 3 read-write 0 Sample window width is 4 sample clock cycles. #000 1 Sample window width is 8 sample clock cycles. #001 10 Sample window width is 16 sample clock cycles. #010 11 Sample window width is 32 sample clock cycles. #011 100 Sample window width is 64 sample clock cycles. #100 101 Sample window width is 128 sample clock cycles. #101 110 Sample window width is 256 sample clock cycles. #110 111 Sample window width is 512 sample clock cycles. #111 FDPRS Fault Detect Clock Prescaler 12 3 read-write 0 1/1 bus clock. #000 1 1/2 bus clock. #001 10 1/4 bus clock. #010 11 1/8 bus clock. #011 100 1/16 bus clock. #100 101 1/32 bus clock. #101 110 1/64 bus clock. #110 111 1/128 bus clock. #111 FDSR LCD Fault Detect Status Register 0xC 32 read-write 0 0xFFFFFFFF FDCNT Fault Detect Counter 0 8 read-only 0 No "one" samples. #0 1 1 "one" samples. #1 10 2 "one" samples. #10 11111110 254 "one" samples. #11111110 11111111 255 or more "one" samples. The FDCNT can overflow. Therefore, FDSWW and FDPRS must be reconfigured for proper sampling. #11111111 FDCF Fault Detection Complete Flag 15 1 read-write 0 Fault detection is not completed. #0 1 Fault detection is completed. #1 2 0x4 L,H PEN%s LCD Pin Enable register 0x10 32 read-write 0 0xFFFFFFFF PEN LCD Pin Enable 0 32 read-write 0 LCD operation disabled on LCD_Pn. #0 1 LCD operation enabled on LCD_Pn. #1 2 0x4 L,H BPEN%s LCD Back Plane Enable register 0x18 32 read-write 0 0xFFFFFFFF BPEN Back Plane Enable 0 32 read-write 0 Front plane operation enabled on LCD_Pn. #0 1 Back plane operation enabled on LCD_Pn. #1 WF3TO0 LCD Waveform register LCD 0x20 32 read-write 0 0xFFFFFFFF WF0 Controls segments or phases connected to LCD_P0 as described above for WF3. 0 8 read-write WF1 Controls segments or phases connected to LCD_P1 as described above for WF3. 8 8 read-write WF2 Controls segments or phases connected to LCD_P2 as described above for WF3. 16 8 read-write WF3 Segment-on front plane operation - Each bit turns on or off the segments associated with LCD_P3 in the following pattern: HGFEDCBA (most significant bit controls segment H and least significant bit controls segment A) 24 8 read-write WF0 LCD Waveform Register 0. LCD 0x20 8 read-write 0 0 BPALCD0 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD0 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD0 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD0 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD0 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD0 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD0 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD0 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF1 LCD Waveform Register 1. 0x21 8 read-write 0 0 BPALCD1 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD1 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD1 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD1 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD1 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD1 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD1 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD1 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF2 LCD Waveform Register 2. 0x22 8 read-write 0 0 BPALCD2 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD2 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD2 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD2 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD2 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD2 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD2 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD2 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF3 LCD Waveform Register 3. 0x23 8 read-write 0 0 BPALCD3 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD3 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD3 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD3 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD3 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD3 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD3 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD3 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF7TO4 LCD Waveform register LCD 0x24 32 read-write 0 0xFFFFFFFF WF4 Controls segments or phases connected to LCD_P4 as described above for WF3TO0[WF3]. 0 8 read-write WF5 Controls segments or phases connected to LCD_P5 as described above for WF3TO0[WF3]. 8 8 read-write WF6 Controls segments or phases connected to LCD_P6 as described above for WF3TO0[WF3]. 16 8 read-write WF7 Controls segments or phases connected to LCD_P7 as described above for WF3TO0[WF3]. 24 8 read-write WF4 LCD Waveform Register 4. LCD 0x24 8 read-write 0 0 BPALCD4 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD4 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD4 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD4 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD4 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD4 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD4 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD4 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF5 LCD Waveform Register 5. 0x25 8 read-write 0 0 BPALCD5 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD5 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD5 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD5 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD5 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD5 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD5 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD5 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF6 LCD Waveform Register 6. 0x26 8 read-write 0 0 BPALCD6 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD6 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD6 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD6 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD6 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD6 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD6 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD6 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF7 LCD Waveform Register 7. 0x27 8 read-write 0 0 BPALCD7 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD7 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD7 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD7 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD7 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD7 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD7 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD7 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF11TO8 LCD Waveform register LCD 0x28 32 read-write 0 0xFFFFFFFF WF8 Controls segments or phases connected to LCD_P8 as described above for WF3TO0[WF3]. 0 8 read-write WF9 Controls segments or phases connected to LCD_P9 as described above for WF3TO0[WF3]. 8 8 read-write WF10 Controls segments or phases connected to LCD_P10 as described above for WF3TO0[WF3]. 16 8 read-write WF11 Controls segments or phases connected to LCD_P11 as described above for WF3TO0[WF3]. 24 8 read-write WF8 LCD Waveform Register 8. LCD 0x28 8 read-write 0 0 BPALCD8 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD8 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD8 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD8 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD8 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD8 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD8 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD8 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF9 LCD Waveform Register 9. 0x29 8 read-write 0 0 BPALCD9 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD9 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD9 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD9 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD9 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD9 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD9 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD9 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF10 LCD Waveform Register 10. 0x2A 8 read-write 0 0 BPALCD10 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD10 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD10 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD10 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD10 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD10 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD10 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD10 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF11 LCD Waveform Register 11. 0x2B 8 read-write 0 0 BPALCD11 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD11 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD11 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD11 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD11 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD11 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD11 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD11 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF15TO12 LCD Waveform register LCD 0x2C 32 read-write 0 0xFFFFFFFF WF12 Controls segments or phases connected to LCD_P12 as described above for WF3TO0[WF3]. 0 8 read-write WF13 Controls segments or phases connected to LCD_P13 as described above for WF3TO0[WF3]. 8 8 read-write WF14 Controls segments or phases connected to LCD_P14 as described above for WF3TO0[WF3]. 16 8 read-write WF15 Controls segments or phases connected to LCD_P15 as described above for WF3TO0[WF3]. 24 8 read-write WF12 LCD Waveform Register 12. LCD 0x2C 8 read-write 0 0 BPALCD12 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD12 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD12 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD12 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD12 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD12 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD12 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD12 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF13 LCD Waveform Register 13. 0x2D 8 read-write 0 0 BPALCD13 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD13 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD13 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD13 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD13 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD13 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD13 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD13 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF14 LCD Waveform Register 14. 0x2E 8 read-write 0 0 BPALCD14 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD14 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD14 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD14 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD14 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD14 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD14 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD14 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF15 LCD Waveform Register 15. 0x2F 8 read-write 0 0 BPALCD15 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD15 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD15 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD15 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD15 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD15 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD15 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD15 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF19TO16 LCD Waveform register LCD 0x30 32 read-write 0 0xFFFFFFFF WF16 Controls segments or phases connected to LCD_P16 as described above for WF3TO0[WF3]. 0 8 read-write WF17 Controls segments or phases connected to LCD_P17 as described above for WF3TO0[WF3]. 8 8 read-write WF18 Controls segments or phases connected to LCD_P18 as described above for WF3TO0[WF3]. 16 8 read-write WF19 Controls segments or phases connected to LCD_P19 as described above for WF3TO0[WF3]. 24 8 read-write WF16 LCD Waveform Register 16. LCD 0x30 8 read-write 0 0 BPALCD16 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD16 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD16 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD16 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD16 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD16 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD16 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD16 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF17 LCD Waveform Register 17. 0x31 8 read-write 0 0 BPALCD17 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD17 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD17 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD17 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD17 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD17 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD17 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD17 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF18 LCD Waveform Register 18. 0x32 8 read-write 0 0 BPALCD18 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD18 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD18 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD18 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD18 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD18 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD18 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD18 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF19 LCD Waveform Register 19. 0x33 8 read-write 0 0 BPALCD19 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD19 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD19 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD19 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD19 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD19 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD19 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD19 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF23TO20 LCD Waveform register LCD 0x34 32 read-write 0 0xFFFFFFFF WF20 Controls segments or phases connected to LCD_P20 as described above for WF3TO0[WF3]. 0 8 read-write WF21 Controls segments or phases connected to LCD_P21 as described above for WF3TO0[WF3]. 8 8 read-write WF22 Controls segments or phases connected to LCD_P22 as described above for WF3TO0[WF3]. 16 8 read-write WF23 Controls segments or phases connected to LCD_P23 as described above for WF3TO0[WF3]. 24 8 read-write WF20 LCD Waveform Register 20. LCD 0x34 8 read-write 0 0 BPALCD20 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD20 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD20 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD20 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD20 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD20 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD20 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD20 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF21 LCD Waveform Register 21. 0x35 8 read-write 0 0 BPALCD21 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD21 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD21 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD21 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD21 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD21 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD21 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD21 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF22 LCD Waveform Register 22. 0x36 8 read-write 0 0 BPALCD22 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD22 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD22 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD22 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD22 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD22 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD22 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD22 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF23 LCD Waveform Register 23. 0x37 8 read-write 0 0 BPALCD23 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD23 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD23 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD23 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD23 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD23 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD23 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD23 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF27TO24 LCD Waveform register LCD 0x38 32 read-write 0 0xFFFFFFFF WF24 Controls segments or phases connected to LCD_P24 as described above for WF3TO0[WF3]. 0 8 read-write WF25 Controls segments or phases connected to LCD_P25 as described above for WF3TO0[WF3]. 8 8 read-write WF26 Controls segments or phases connected to LCD_P26 as described above for WF3TO0[WF3]. 16 8 read-write WF27 Controls segments or phases connected to LCD_P27 as described above for WF3TO0[WF3]. 24 8 read-write WF24 LCD Waveform Register 24. LCD 0x38 8 read-write 0 0 BPALCD24 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD24 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD24 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD24 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD24 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD24 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD24 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD24 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF25 LCD Waveform Register 25. 0x39 8 read-write 0 0 BPALCD25 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD25 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD25 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD25 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD25 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD25 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD25 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD25 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF26 LCD Waveform Register 26. 0x3A 8 read-write 0 0 BPALCD26 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD26 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD26 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD26 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD26 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD26 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD26 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD26 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF27 LCD Waveform Register 27. 0x3B 8 read-write 0 0 BPALCD27 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD27 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD27 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD27 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD27 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD27 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD27 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD27 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF31TO28 LCD Waveform register LCD 0x3C 32 read-write 0 0xFFFFFFFF WF28 Controls segments or phases connected to LCD_P28 as described above for WF3TO0[WF3]. 0 8 read-write WF29 Controls segments or phases connected to LCD_P29 as described above for WF3TO0[WF3]. 8 8 read-write WF30 Controls segments or phases connected to LCD_P30 as described above for WF3TO0[WF3]. 16 8 read-write WF31 Controls segments or phases connected to LCD_P31 as described above for WF3TO0[WF3]. 24 8 read-write WF28 LCD Waveform Register 28. LCD 0x3C 8 read-write 0 0 BPALCD28 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD28 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD28 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD28 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD28 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD28 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD28 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD28 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF29 LCD Waveform Register 29. 0x3D 8 read-write 0 0 BPALCD29 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD29 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD29 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD29 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD29 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD29 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD29 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD29 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF30 LCD Waveform Register 30. 0x3E 8 read-write 0 0 BPALCD30 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD30 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD30 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD30 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD30 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD30 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD30 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD30 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF31 LCD Waveform Register 31. 0x3F 8 read-write 0 0 BPALCD31 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD31 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD31 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD31 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD31 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD31 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD31 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD31 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF35TO32 LCD Waveform register LCD 0x40 32 read-write 0 0xFFFFFFFF WF32 Controls segments or phases connected to LCD_P32 as described above for WF3TO0[WF3]. 0 8 read-write WF33 Controls segments or phases connected to LCD_P33 as described above for WF3TO0[WF3]. 8 8 read-write WF34 Controls segments or phases connected to LCD_P34 as described above for WF3TO0[WF3]. 16 8 read-write WF35 Controls segments or phases connected to LCD_P35 as described above for WF3TO0[WF3]. 24 8 read-write WF32 LCD Waveform Register 32. LCD 0x40 8 read-write 0 0 BPALCD32 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD32 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD32 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD32 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD32 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD32 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD32 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD32 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF33 LCD Waveform Register 33. 0x41 8 read-write 0 0 BPALCD33 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD33 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD33 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD33 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD33 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD33 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD33 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD33 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF34 LCD Waveform Register 34. 0x42 8 read-write 0 0 BPALCD34 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD34 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD34 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD34 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD34 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD34 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD34 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD34 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF35 LCD Waveform Register 35. 0x43 8 read-write 0 0 BPALCD35 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD35 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD35 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD35 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD35 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD35 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD35 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD35 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF39TO36 LCD Waveform register LCD 0x44 32 read-write 0 0xFFFFFFFF WF36 Controls segments or phases connected to LCD_P36 as described above for WF3TO0[WF3]. 0 8 read-write WF37 Controls segments or phases connected to LCD_P37 as described above for WF3TO0[WF3]. 8 8 read-write WF38 Controls segments or phases connected to LCD_P38 as described above for WF3TO0[WF3]. 16 8 read-write WF39 Controls segments or phases connected to LCD_P39 as described above for WF3TO0[WF3]. 24 8 read-write WF36 LCD Waveform Register 36. LCD 0x44 8 read-write 0 0 BPALCD36 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD36 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD36 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD36 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD36 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD36 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD36 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD36 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF37 LCD Waveform Register 37. 0x45 8 read-write 0 0 BPALCD37 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD37 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD37 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD37 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD37 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD37 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD37 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD37 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF38 LCD Waveform Register 38. 0x46 8 read-write 0 0 BPALCD38 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD38 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD38 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD38 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD38 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD38 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD38 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD38 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF39 LCD Waveform Register 39. 0x47 8 read-write 0 0 BPALCD39 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD39 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD39 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD39 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD39 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD39 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD39 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD39 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF43TO40 LCD Waveform register LCD 0x48 32 read-write 0 0xFFFFFFFF WF40 Controls segments or phases connected to LCD_P40 as described above for WF3TO0[WF3]. 0 8 read-write WF41 Controls segments or phases connected to LCD_P41 as described above for WF3TO0[WF3]. 8 8 read-write WF42 Controls segments or phases connected to LCD_P42 as described above for WF3TO0[WF3]. 16 8 read-write WF43 Controls segments or phases connected to LCD_P43 as described above for WF3TO0[WF3]. 24 8 read-write WF40 LCD Waveform Register 40. LCD 0x48 8 read-write 0 0 BPALCD40 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD40 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD40 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD40 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD40 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD40 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD40 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD40 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF41 LCD Waveform Register 41. 0x49 8 read-write 0 0 BPALCD41 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD41 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD41 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD41 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD41 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD41 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD41 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD41 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF42 LCD Waveform Register 42. 0x4A 8 read-write 0 0 BPALCD42 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD42 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD42 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD42 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD42 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD42 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD42 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD42 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF43 LCD Waveform Register 43. 0x4B 8 read-write 0 0 BPALCD43 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD43 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD43 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD43 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD43 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD43 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD43 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD43 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF47TO44 LCD Waveform register LCD 0x4C 32 read-write 0 0xFFFFFFFF WF44 Controls segments or phases connected to LCD_P44 as described above for WF3TO0[WF3]. 0 8 read-write WF45 Controls segments or phases connected to LCD_P45 as described above for WF3TO0[WF3]. 8 8 read-write WF46 Controls segments or phases connected to LCD_P46 as described above for WF3TO0[WF3]. 16 8 read-write WF47 Controls segments or phases connected to LCD_P47 as described above for WF3TO0[WF3]. 24 8 read-write WF44 LCD Waveform Register 44. LCD 0x4C 8 read-write 0 0 BPALCD44 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD44 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD44 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD44 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD44 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD44 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD44 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD44 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF45 LCD Waveform Register 45. 0x4D 8 read-write 0 0 BPALCD45 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD45 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD45 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD45 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD45 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD45 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD45 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD45 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF46 LCD Waveform Register 46. 0x4E 8 read-write 0 0 BPALCD46 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD46 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD46 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD46 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD46 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD46 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD46 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD46 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF47 LCD Waveform Register 47. 0x4F 8 read-write 0 0 BPALCD47 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD47 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD47 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD47 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD47 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD47 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD47 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD47 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF51TO48 LCD Waveform register LCD 0x50 32 read-write 0 0xFFFFFFFF WF48 Controls segments or phases connected to LCD_P48 as described above for WF3TO0[WF3]. 0 8 read-write WF49 Controls segments or phases connected to LCD_P49 as described above for WF3TO0[WF3]. 8 8 read-write WF50 Controls segments or phases connected to LCD_P50 as described above for WF3TO0[WF3]. 16 8 read-write WF51 Controls segments or phases connected to LCD_P51 as described above for WF3TO0[WF3]. 24 8 read-write WF48 LCD Waveform Register 48. LCD 0x50 8 read-write 0 0 BPALCD48 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD48 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD48 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD48 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD48 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD48 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD48 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD48 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF49 LCD Waveform Register 49. 0x51 8 read-write 0 0 BPALCD49 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD49 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD49 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD49 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD49 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD49 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD49 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD49 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF50 LCD Waveform Register 50. 0x52 8 read-write 0 0 BPALCD50 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD50 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD50 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD50 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD50 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD50 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD50 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD50 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF51 LCD Waveform Register 51. 0x53 8 read-write 0 0 BPALCD51 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD51 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD51 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD51 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD51 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD51 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD51 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD51 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF55TO52 LCD Waveform register LCD 0x54 32 read-write 0 0xFFFFFFFF WF52 Controls segments or phases connected to LCD_P52 as described above for WF3TO0[WF3]. 0 8 read-write WF53 Controls segments or phases connected to LCD_P53 as described above for WF3TO0[WF3]. 8 8 read-write WF54 Controls segments or phases connected to LCD_P54 as described above for WF3TO0[WF3]. 16 8 read-write WF55 Controls segments or phases connected to LCD_P55 as described above for WF3TO0[WF3]. 24 8 read-write WF52 LCD Waveform Register 52. LCD 0x54 8 read-write 0 0 BPALCD52 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD52 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD52 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD52 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD52 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD52 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD52 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD52 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF53 LCD Waveform Register 53. 0x55 8 read-write 0 0 BPALCD53 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD53 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD53 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD53 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD53 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD53 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD53 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD53 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF54 LCD Waveform Register 54. 0x56 8 read-write 0 0 BPALCD54 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD54 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD54 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD54 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD54 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD54 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD54 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD54 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF55 LCD Waveform Register 55. 0x57 8 read-write 0 0 BPALCD55 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD55 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD55 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD55 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD55 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD55 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD55 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD55 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF59TO56 LCD Waveform register LCD 0x58 32 read-write 0 0xFFFFFFFF WF56 Controls segments or phases connected to LCD_P56 as described above for WF3TO0[WF3]. 0 8 read-write WF57 Controls segments or phases connected to LCD_P57 as described above for WF3TO0[WF3]. 8 8 read-write WF58 Controls segments or phases connected to LCD_P58 as described above for WF3TO0[WF3]. 16 8 read-write WF59 Controls segments or phases connected to LCD_P59 as described above for WF3TO0[WF3]. 24 8 read-write WF56 LCD Waveform Register 56. LCD 0x58 8 read-write 0 0 BPALCD56 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD56 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD56 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD56 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD56 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD56 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD56 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD56 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF57 LCD Waveform Register 57. 0x59 8 read-write 0 0 BPALCD57 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD57 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD57 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD57 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD57 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD57 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD57 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD57 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF58 LCD Waveform Register 58. 0x5A 8 read-write 0 0 BPALCD58 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD58 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD58 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD58 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD58 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD58 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD58 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD58 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF59 LCD Waveform Register 59. 0x5B 8 read-write 0 0 BPALCD59 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD59 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD59 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD59 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD59 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD59 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD59 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD59 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF63TO60 LCD Waveform register LCD 0x5C 32 read-write 0 0xFFFFFFFF WF60 Controls segments or phases connected to LCD_P60 as described above for WF3TO0[WF3]. 0 8 read-write WF61 Controls segments or phases connected to LCD_P61 as described above for WF3TO0[WF3]. 8 8 read-write WF62 Controls segments or phases connected to LCD_P62 as described above for WF3TO0[WF3]. 16 8 read-write WF63 Controls segments or phases connected to LCD_P63 as described above for WF3TO0[WF3]. 24 8 read-write WF60 LCD Waveform Register 60. LCD 0x5C 8 read-write 0 0 BPALCD60 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD60 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD60 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD60 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD60 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD60 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD60 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD60 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF61 LCD Waveform Register 61. 0x5D 8 read-write 0 0 BPALCD61 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD61 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD61 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD61 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD61 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD61 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD61 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD61 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF62 LCD Waveform Register 62. 0x5E 8 read-write 0 0 BPALCD62 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD62 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD62 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD62 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD62 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD62 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD62 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD62 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 WF63 LCD Waveform Register 63. 0x5F 8 read-write 0 0 BPALCD63 no description available 0 1 read-write 0 LCD segment off or LCD backplane inactive for phase A #0 1 LCD segment on or LCD backplane active for phase A #1 BPBLCD63 no description available 1 1 read-write 0 LCD segment off or LCD backplane inactive for phase B #0 1 LCD segment on or LCD backplane active for phase B #1 BPCLCD63 no description available 2 1 read-write 0 LCD segment off or LCD backplane inactive for phase C #0 1 LCD segment on or LCD backplane active for phase C #1 BPDLCD63 no description available 3 1 read-write 0 LCD segment off or LCD backplane inactive for phase D #0 1 LCD segment on or LCD backplane active for phase D #1 BPELCD63 no description available 4 1 read-write 0 LCD segment off or LCD backplane inactive for phase E #0 1 LCD segment on or LCD backplane active for phase E #1 BPFLCD63 no description available 5 1 read-write 0 LCD segment off or LCD backplane inactive for phase F #0 1 LCD segment on or LCD backplane active for phase F #1 BPGLCD63 no description available 6 1 read-write 0 LCD segment off or LCD backplane inactive for phase G #0 1 LCD segment on or LCD backplane active for phase G #1 BPHLCD63 no description available 7 1 read-write 0 LCD segment off or LCD backplane inactive for phase H #0 1 LCD segment on or LCD backplane active for phase H #1 MCG Multipurpose Clock Generator module MCG_ 0x40064000 0 0x10 registers MCG 27 C1 MCG Control 1 Register 0 8 read-write 0x4 0xFF IREFSTEN Internal Reference Stop Enable 0 1 read-write 0 Internal reference clock is disabled in Stop mode. #0 1 Internal reference clock is enabled in Stop mode if IRCLKEN is set or if MCG is in FEI, FBI, or BLPI modes before entering Stop mode. #1 IRCLKEN Internal Reference Clock Enable 1 1 read-write 0 MCGIRCLK inactive. #0 1 MCGIRCLK active. #1 IREFS Internal Reference Select 2 1 read-write 0 External reference clock is selected. #0 1 The slow internal reference clock is selected. #1 FRDIV FLL External Reference Divider 3 3 read-write 000 If RANGE 0 = 0 or OSCSEL=1 , Divide Factor is 1; for all other RANGE 0 values, Divide Factor is 32. #000 001 If RANGE 0 = 0 or OSCSEL=1 , Divide Factor is 2; for all other RANGE 0 values, Divide Factor is 64. #001 010 If RANGE 0 = 0 or OSCSEL=1 , Divide Factor is 4; for all other RANGE 0 values, Divide Factor is 128. #010 011 If RANGE 0 = 0 or OSCSEL=1 , Divide Factor is 8; for all other RANGE 0 values, Divide Factor is 256. #011 100 If RANGE 0 = 0 or OSCSEL=1 , Divide Factor is 16; for all other RANGE 0 values, Divide Factor is 512. #100 101 If RANGE 0 = 0 or OSCSEL=1 , Divide Factor is 32; for all other RANGE 0 values, Divide Factor is 1024. #101 110 If RANGE 0 = 0 or OSCSEL=1 , Divide Factor is 64; for all other RANGE 0 values, Divide Factor is 1280 . #110 111 If RANGE 0 = 0 or OSCSEL=1 , Divide Factor is 128; for all other RANGE 0 values, Divide Factor is 1536 . #111 CLKS Clock Source Select 6 2 read-write 00 Encoding 0 - Output of FLL or PLL is selected (depends on PLLS control bit). #00 01 Encoding 1 - Internal reference clock is selected. #01 10 Encoding 2 - External reference clock is selected. #10 11 Encoding 3 - Reserved. #11 C2 MCG Control 2 Register 0x1 8 read-write 0xC0 0xFF IRCS Internal Reference Clock Select 0 1 read-write 0 Slow internal reference clock selected. #0 1 Fast internal reference clock selected. #1 LP Low Power Select 1 1 read-write 0 FLL or PLL is not disabled in bypass modes. #0 1 FLL or PLL is disabled in bypass modes (lower power) #1 EREFS0 External Reference Select 2 1 read-write 0 External reference clock requested. #0 1 Oscillator requested. #1 HGO0 High Gain Oscillator Select 3 1 read-write 0 Configure crystal oscillator for low-power operation. #0 1 Configure crystal oscillator for high-gain operation. #1 RANGE0 Frequency Range Select 4 2 read-write 00 Encoding 0 - Low frequency range selected for the crystal oscillator . #00 01 Encoding 1 - High frequency range selected for the crystal oscillator . #01 1X Encoding 2 - Very high frequency range selected for the crystal oscillator . #1x FCFTRIM Fast Internal Reference Clock Fine Trim 6 1 read-write LOCRE0 Loss of Clock Reset Enable 7 1 read-write 0 Interrupt request is generated on a loss of OSC0 external reference clock. #0 1 Generate a reset request on a loss of OSC0 external reference clock. #1 C3 MCG Control 3 Register 0x2 8 read-write 0 0 SCTRIM Slow Internal Reference Clock Trim Setting 0 8 read-write C4 MCG Control 4 Register 0x3 8 read-write 0 0xE0 SCFTRIM Slow Internal Reference Clock Fine Trim 0 1 read-write FCTRIM Fast Internal Reference Clock Trim Setting 1 4 read-write DRST_DRS DCO Range Select 5 2 read-write 00 Encoding 0 - Low range (reset default). #00 01 Encoding 1 - Mid range. #01 10 Encoding 2 - Mid-high range. #10 11 Encoding 3 - High range. #11 DMX32 DCO Maximum Frequency with 32.768 kHz Reference 7 1 read-write 0 DCO has a default range of 25%. #0 1 DCO is fine-tuned for maximum frequency with 32.768 kHz reference. #1 C5 MCG Control 5 Register 0x4 8 read-write 0 0xFF PRDIV0 PLL External Reference Divider 0 5 read-write 0 Divide Factor is 1 #00000 1 Divide Factor is 2 #00001 2 Divide Factor is 3 #00010 3 Divide Factor is 4 #00011 4 Divide Factor is 5 #00100 5 Divide Factor is 6 #00101 6 Divide Factor is 7 #00110 7 Divide Factor is 8 #00111 8 Divide Factor is 9 #01000 9 Divide Factor is 10 #01001 10 Divide Factor is 11 #01010 11 Divide Factor is 12 #01011 12 Divide Factor is 13 #01100 13 Divide Factor is 14 #01101 14 Divide Factor is 15 #01110 15 Divide Factor is 16 #01111 16 Divide Factor is 17 #10000 17 Divide Factor is 18 #10001 18 Divide Factor is 19 #10010 19 Divide Factor is 20 #10011 20 Divide Factor is 21 #10100 21 Divide Factor is 22 #10101 22 Divide Factor is 23 #10110 23 Divide Factor is 24 #10111 24 Divide Factor is 25 #11000 25 Divide Factor is 26 #11001 26 Divide Factor is 27 #11010 27 Divide Factor is 28 #11011 28 Divide Factor is 29 #11100 29 Divide Factor is 30 #11101 30 Divide Factor is 31 #11110 31 Divide Factor is 32 #11111 PLLSTEN0 PLL Stop Enable 5 1 read-write 0 MCGPLLCLK is disabled in any of the Stop modes. #0 1 MCGPLLCLK is enabled if system is in Normal Stop mode. #1 PLLCLKEN0 PLL Clock Enable 6 1 read-write 0 MCGPLLCLK is inactive. #0 1 MCGPLLCLK is active. #1 C6 MCG Control 6 Register 0x5 8 read-write 0 0xFF VDIV0 VCO 0 Divider 0 5 read-write 0 Multiply Factor is 24 #00000 1 Multiply Factor is 25 #00001 2 Multiply Factor is 26 #00010 3 Multiply Factor is 27 #00011 4 Multiply Factor is 28 #00100 5 Multiply Factor is 29 #00101 6 Multiply Factor is 30 #00110 7 Multiply Factor is 31 #00111 8 Multiply Factor is 32 #01000 9 Multiply Factor is 33 #01001 10 Multiply Factor is 34 #01010 11 Multiply Factor is 35 #01011 12 Multiply Factor is 36 #01100 13 Multiply Factor is 37 #01101 14 Multiply Factor is 38 #01110 15 Multiply Factor is 39 #01111 16 Multiply Factor is 40 #10000 17 Multiply Factor is 41 #10001 18 Multiply Factor is 42 #10010 19 Multiply Factor is 43 #10011 20 Multiply Factor is 44 #10100 21 Multiply Factor is 45 #10101 22 Multiply Factor is 46 #10110 23 Multiply Factor is 47 #10111 24 Multiply Factor is 48 #11000 25 Multiply Factor is 49 #11001 26 Multiply Factor is 50 #11010 27 Multiply Factor is 51 #11011 28 Multiply Factor is 52 #11100 29 Multiply Factor is 53 #11101 30 Multiply Factor is 54 #11110 31 Multiply Factor is 55 #11111 CME0 Clock Monitor Enable 5 1 read-write 0 External clock monitor is disabled for OSC0. #0 1 External clock monitor is enabled for OSC0. #1 PLLS PLL Select 6 1 read-write 0 FLL is selected. #0 1 PLL is selected (PRDIV 0 need to be programmed to the correct divider to generate a PLL reference clock in the range of 2-4 MHz prior to setting the PLLS bit). #1 LOLIE0 Loss of Lock Interrrupt Enable 7 1 read-write 0 No interrupt request is generated on loss of lock. #0 1 Generate an interrupt request on loss of lock. #1 S MCG Status Register 0x6 8 read-write 0x10 0xFF IRCST Internal Reference Clock Status 0 1 read-only 0 Source of internal reference clock is the slow clock (32 kHz IRC). #0 1 Source of internal reference clock is the fast clock (4 MHz IRC). #1 OSCINIT0 OSC Initialization 1 1 read-only CLKST Clock Mode Status 2 2 read-only 00 Encoding 0 - Output of the FLL is selected (reset default). #00 01 Encoding 1 - Internal reference clock is selected. #01 10 Encoding 2 - External reference clock is selected. #10 11 Encoding 3 - Output of the PLL is selected. #11 IREFST Internal Reference Status 4 1 read-only 0 Source of FLL reference clock is the external reference clock. #0 1 Source of FLL reference clock is the internal reference clock. #1 PLLST PLL Select Status 5 1 read-only 0 Source of PLLS clock is FLL clock. #0 1 Source of PLLS clock is PLL output clock. #1 LOCK0 Lock Status 6 1 read-only 0 PLL is currently unlocked. #0 1 PLL is currently locked. #1 LOLS0 Loss of Lock Status 7 1 read-write 0 PLL has not lost lock since LOLS 0 was last cleared. #0 1 PLL has lost lock since LOLS 0 was last cleared. #1 SC MCG Status and Control Register 0x8 8 read-write 0x2 0xFF LOCS0 OSC0 Loss of Clock Status 0 1 read-write 0 Loss of OSC0 has not occurred. #0 1 Loss of OSC0 has occurred. #1 FCRDIV Fast Clock Internal Reference Divider 1 3 read-write 000 Divide Factor is 1 #000 001 Divide Factor is 2. #001 010 Divide Factor is 4. #010 011 Divide Factor is 8. #011 100 Divide Factor is 16 #100 101 Divide Factor is 32 #101 110 Divide Factor is 64 #110 111 Divide Factor is 128. #111 FLTPRSRV FLL Filter Preserve Enable 4 1 read-write 0 FLL filter and FLL frequency will reset on changes to currect clock mode. #0 1 Fll filter and FLL frequency retain their previous values during new clock mode change. #1 ATMF Automatic Trim Machine Fail Flag 5 1 read-write 0 Automatic Trim Machine completed normally. #0 1 Automatic Trim Machine failed. #1 ATMS Automatic Trim Machine Select 6 1 read-write 0 32 kHz Internal Reference Clock selected. #0 1 4 MHz Internal Reference Clock selected. #1 ATME Automatic Trim Machine Enable 7 1 read-write 0 Auto Trim Machine disabled. #0 1 Auto Trim Machine enabled. #1 ATCVH MCG Auto Trim Compare Value High Register 0xA 8 read-write 0 0xFF ATCVH ATM Compare Value High 0 8 read-write ATCVL MCG Auto Trim Compare Value Low Register 0xB 8 read-write 0 0xFF ATCVL ATM Compare Value Low 0 8 read-write C7 MCG Control 7 Register 0xC 8 read-write 0 0xFF OSCSEL MCG OSC Clock Select 0 1 read-write 0 Selects System Oscillator (OSCCLK). #0 1 Selects 32 kHz RTC Oscillator. #1 C8 MCG Control 8 Register 0xD 8 read-write 0x80 0xFF LOLRE PLL Loss of Lock Reset Enable 6 1 read-write 0 Interrupt request is generated on a PLL loss of lock indication. The PLL loss of lock interrupt enable bit must also be set to generate the interrupt request. #0 1 Generate a reset request on a PLL loss of lock indication. #1 C9 MCG Control 9 Register 0xE 8 read-only 0 0xFF C10 MCG Control 10 Register 0xF 8 read-only 0 0xFF OSC0 Oscillator OSC0_ 0x40065000 0 0x1 registers CR OSC Control Register 0 8 read-write 0 0xFF SC16P Oscillator 16 pF Capacitor Load Configure 0 1 read-write 0 Disable the selection. #0 1 Add 16 pF capacitor to the oscillator load. #1 SC8P Oscillator 8 pF Capacitor Load Configure 1 1 read-write 0 Disable the selection. #0 1 Add 8 pF capacitor to the oscillator load. #1 SC4P Oscillator 4 pF Capacitor Load Configure 2 1 read-write 0 Disable the selection. #0 1 Add 4 pF capacitor to the oscillator load. #1 SC2P Oscillator 2 pF Capacitor Load Configure 3 1 read-write 0 Disable the selection. #0 1 Add 2 pF capacitor to the oscillator load. #1 EREFSTEN External Reference Stop Enable 5 1 read-write 0 External reference clock is disabled in Stop mode. #0 1 External reference clock stays enabled in Stop mode if ERCLKEN is set before entering Stop mode. #1 ERCLKEN External Reference Enable 7 1 read-write 0 External reference clock is inactive. #0 1 External reference clock is enabled. #1 I2C0 Inter-Integrated Circuit I2C I2C0_ 0x40066000 0 0xC registers I2C0 8 A1 I2C Address Register 1 0 8 read-write 0 0xFF AD Address 1 7 read-write F I2C Frequency Divider register 0x1 8 read-write 0 0xFF ICR ClockRate 0 6 read-write MULT Multiplier Factor 6 2 read-write 00 mul = 1 #00 01 mul = 2 #01 10 mul = 4 #10 C1 I2C Control Register 1 0x2 8 read-write 0 0xFF DMAEN DMA Enable 0 1 read-write 0 All DMA signalling disabled. #0 1 DMA transfer is enabled. While SMB[FACK] = 0, the following conditions trigger the DMA request: a data byte is received, and either address or data is transmitted. (ACK/NACK is automatic) the first byte received matches the A1 register or is a general call address. If any address matching occurs, S[IAAS] and S[TCF] are set. If the direction of transfer is known from master to slave, then it is not required to check S[SRW]. With this assumption, DMA can also be used in this case. In other cases, if the master reads data from the slave, then it is required to rewrite the C1 register operation. With this assumption, DMA cannot be used. When FACK = 1, an address or a data byte is transmitted. #1 WUEN Wakeup Enable 1 1 read-write 0 Normal operation. No interrupt generated when address matching in low power mode. #0 1 Enables the wakeup function in low power mode. #1 RSTA Repeat START 2 1 write-only TXAK Transmit Acknowledge Enable 3 1 read-write 0 An acknowledge signal is sent to the bus on the following receiving byte (if FACK is cleared) or the current receiving byte (if FACK is set). #0 1 No acknowledge signal is sent to the bus on the following receiving data byte (if FACK is cleared) or the current receiving data byte (if FACK is set). #1 TX Transmit Mode Select 4 1 read-write 0 Receive #0 1 Transmit #1 MST Master Mode Select 5 1 read-write 0 Slave mode #0 1 Master mode #1 IICIE I2C Interrupt Enable 6 1 read-write 0 Disabled #0 1 Enabled #1 IICEN I2C Enable 7 1 read-write 0 Disabled #0 1 Enabled #1 S I2C Status register 0x3 8 read-write 0x80 0xFF RXAK Receive Acknowledge 0 1 read-only 0 Acknowledge signal was received after the completion of one byte of data transmission on the bus #0 1 No acknowledge signal detected #1 IICIF Interrupt Flag 1 1 read-write 0 No interrupt pending #0 1 Interrupt pending #1 SRW Slave Read/Write 2 1 read-only 0 Slave receive, master writing to slave #0 1 Slave transmit, master reading from slave #1 RAM Range Address Match 3 1 read-write 0 Not addressed #0 1 Addressed as a slave #1 ARBL Arbitration Lost 4 1 read-write 0 Standard bus operation. #0 1 Loss of arbitration. #1 BUSY Bus Busy 5 1 read-only 0 Bus is idle #0 1 Bus is busy #1 IAAS Addressed As A Slave 6 1 read-write 0 Not addressed #0 1 Addressed as a slave #1 TCF Transfer Complete Flag 7 1 read-only 0 Transfer in progress #0 1 Transfer complete #1 D I2C Data I/O register 0x4 8 read-write 0 0xFF DATA Data 0 8 read-write C2 I2C Control Register 2 0x5 8 read-write 0 0xFF AD Slave Address 0 3 read-write RMEN Range Address Matching Enable 3 1 read-write 0 Range mode disabled. No address match occurs for an address within the range of values of the A1 and RA registers. #0 1 Range mode enabled. Address matching occurs when a slave receives an address within the range of values of the A1 and RA registers. #1 SBRC Slave Baud Rate Control 4 1 read-write 0 The slave baud rate follows the master baud rate and clock stretching may occur #0 1 Slave baud rate is independent of the master baud rate #1 HDRS High Drive Select 5 1 read-write 0 Normal drive mode #0 1 High drive mode #1 ADEXT Address Extension 6 1 read-write 0 7-bit address scheme #0 1 10-bit address scheme #1 GCAEN General Call Address Enable 7 1 read-write 0 Disabled #0 1 Enabled #1 FLT I2C Programmable Input Glitch Filter register 0x6 8 read-write 0 0xFF FLT I2C Programmable Filter Factor 0 4 read-write 0 No filter/bypass #0000 STARTF I2C Bus Start Detect Flag 4 1 read-write 0 No start happens on I2C bus #0 1 Start detected on I2C bus #1 SSIE I2C Bus Stop or Start Interrupt Enable 5 1 read-write 0 Stop or start detection interrupt is disabled #0 1 Stop or start detection interrupt is enabled #1 STOPF I2C Bus Stop Detect Flag 6 1 read-write 0 No stop happens on I2C bus #0 1 Stop detected on I2C bus #1 SHEN Stop Hold Enable 7 1 read-write 0 Stop holdoff is disabled. The MCU's entry to stop mode is not gated. #0 1 Stop holdoff is enabled. #1 RA I2C Range Address register 0x7 8 read-write 0 0xFF RAD Range Slave Address 1 7 read-write SMB I2C SMBus Control and Status register 0x8 8 read-write 0 0xFF SHTF2IE SHTF2 Interrupt Enable 0 1 read-write 0 SHTF2 interrupt is disabled #0 1 SHTF2 interrupt is enabled #1 SHTF2 SCL High Timeout Flag 2 1 1 read-write 0 No SCL high and SDA low timeout occurs #0 1 SCL high and SDA low timeout occurs #1 SHTF1 SCL High Timeout Flag 1 2 1 read-only 0 No SCL high and SDA high timeout occurs #0 1 SCL high and SDA high timeout occurs #1 SLTF SCL Low Timeout Flag 3 1 read-write 0 No low timeout occurs #0 1 Low timeout occurs #1 TCKSEL Timeout Counter Clock Select 4 1 read-write 0 Timeout counter counts at the frequency of the I2C module clock / 64 #0 1 Timeout counter counts at the frequency of the I2C module clock #1 SIICAEN Second I2C Address Enable 5 1 read-write 0 I2C address register 2 matching is disabled #0 1 I2C address register 2 matching is enabled #1 ALERTEN SMBus Alert Response Address Enable 6 1 read-write 0 SMBus alert response address matching is disabled #0 1 SMBus alert response address matching is enabled #1 FACK Fast NACK/ACK Enable 7 1 read-write 0 An ACK or NACK is sent on the following receiving data byte #0 1 Writing 0 to TXAK after receiving a data byte generates an ACK. Writing 1 to TXAK after receiving a data byte generates a NACK. #1 A2 I2C Address Register 2 0x9 8 read-write 0xC2 0xFF SAD SMBus Address 1 7 read-write SLTH I2C SCL Low Timeout Register High 0xA 8 read-write 0 0xFF SSLT Most significant byte of SCL low timeout value that determines the timeout period of SCL low. 0 8 read-write SLTL I2C SCL Low Timeout Register Low 0xB 8 read-write 0 0xFF SSLT Least significant byte of SCL low timeout value that determines the timeout period of SCL low. 0 8 read-write I2C1 Inter-Integrated Circuit I2C I2C1_ 0x40067000 0 0xC registers I2C1 9 A1 I2C Address Register 1 0 8 read-write 0 0xFF AD Address 1 7 read-write F I2C Frequency Divider register 0x1 8 read-write 0 0xFF ICR ClockRate 0 6 read-write MULT Multiplier Factor 6 2 read-write 00 mul = 1 #00 01 mul = 2 #01 10 mul = 4 #10 C1 I2C Control Register 1 0x2 8 read-write 0 0xFF DMAEN DMA Enable 0 1 read-write 0 All DMA signalling disabled. #0 1 DMA transfer is enabled. While SMB[FACK] = 0, the following conditions trigger the DMA request: a data byte is received, and either address or data is transmitted. (ACK/NACK is automatic) the first byte received matches the A1 register or is a general call address. If any address matching occurs, S[IAAS] and S[TCF] are set. If the direction of transfer is known from master to slave, then it is not required to check S[SRW]. With this assumption, DMA can also be used in this case. In other cases, if the master reads data from the slave, then it is required to rewrite the C1 register operation. With this assumption, DMA cannot be used. When FACK = 1, an address or a data byte is transmitted. #1 WUEN Wakeup Enable 1 1 read-write 0 Normal operation. No interrupt generated when address matching in low power mode. #0 1 Enables the wakeup function in low power mode. #1 RSTA Repeat START 2 1 write-only TXAK Transmit Acknowledge Enable 3 1 read-write 0 An acknowledge signal is sent to the bus on the following receiving byte (if FACK is cleared) or the current receiving byte (if FACK is set). #0 1 No acknowledge signal is sent to the bus on the following receiving data byte (if FACK is cleared) or the current receiving data byte (if FACK is set). #1 TX Transmit Mode Select 4 1 read-write 0 Receive #0 1 Transmit #1 MST Master Mode Select 5 1 read-write 0 Slave mode #0 1 Master mode #1 IICIE I2C Interrupt Enable 6 1 read-write 0 Disabled #0 1 Enabled #1 IICEN I2C Enable 7 1 read-write 0 Disabled #0 1 Enabled #1 S I2C Status register 0x3 8 read-write 0x80 0xFF RXAK Receive Acknowledge 0 1 read-only 0 Acknowledge signal was received after the completion of one byte of data transmission on the bus #0 1 No acknowledge signal detected #1 IICIF Interrupt Flag 1 1 read-write 0 No interrupt pending #0 1 Interrupt pending #1 SRW Slave Read/Write 2 1 read-only 0 Slave receive, master writing to slave #0 1 Slave transmit, master reading from slave #1 RAM Range Address Match 3 1 read-write 0 Not addressed #0 1 Addressed as a slave #1 ARBL Arbitration Lost 4 1 read-write 0 Standard bus operation. #0 1 Loss of arbitration. #1 BUSY Bus Busy 5 1 read-only 0 Bus is idle #0 1 Bus is busy #1 IAAS Addressed As A Slave 6 1 read-write 0 Not addressed #0 1 Addressed as a slave #1 TCF Transfer Complete Flag 7 1 read-only 0 Transfer in progress #0 1 Transfer complete #1 D I2C Data I/O register 0x4 8 read-write 0 0xFF DATA Data 0 8 read-write C2 I2C Control Register 2 0x5 8 read-write 0 0xFF AD Slave Address 0 3 read-write RMEN Range Address Matching Enable 3 1 read-write 0 Range mode disabled. No address match occurs for an address within the range of values of the A1 and RA registers. #0 1 Range mode enabled. Address matching occurs when a slave receives an address within the range of values of the A1 and RA registers. #1 SBRC Slave Baud Rate Control 4 1 read-write 0 The slave baud rate follows the master baud rate and clock stretching may occur #0 1 Slave baud rate is independent of the master baud rate #1 HDRS High Drive Select 5 1 read-write 0 Normal drive mode #0 1 High drive mode #1 ADEXT Address Extension 6 1 read-write 0 7-bit address scheme #0 1 10-bit address scheme #1 GCAEN General Call Address Enable 7 1 read-write 0 Disabled #0 1 Enabled #1 FLT I2C Programmable Input Glitch Filter register 0x6 8 read-write 0 0xFF FLT I2C Programmable Filter Factor 0 4 read-write 0 No filter/bypass #0000 STARTF I2C Bus Start Detect Flag 4 1 read-write 0 No start happens on I2C bus #0 1 Start detected on I2C bus #1 SSIE I2C Bus Stop or Start Interrupt Enable 5 1 read-write 0 Stop or start detection interrupt is disabled #0 1 Stop or start detection interrupt is enabled #1 STOPF I2C Bus Stop Detect Flag 6 1 read-write 0 No stop happens on I2C bus #0 1 Stop detected on I2C bus #1 SHEN Stop Hold Enable 7 1 read-write 0 Stop holdoff is disabled. The MCU's entry to stop mode is not gated. #0 1 Stop holdoff is enabled. #1 RA I2C Range Address register 0x7 8 read-write 0 0xFF RAD Range Slave Address 1 7 read-write SMB I2C SMBus Control and Status register 0x8 8 read-write 0 0xFF SHTF2IE SHTF2 Interrupt Enable 0 1 read-write 0 SHTF2 interrupt is disabled #0 1 SHTF2 interrupt is enabled #1 SHTF2 SCL High Timeout Flag 2 1 1 read-write 0 No SCL high and SDA low timeout occurs #0 1 SCL high and SDA low timeout occurs #1 SHTF1 SCL High Timeout Flag 1 2 1 read-only 0 No SCL high and SDA high timeout occurs #0 1 SCL high and SDA high timeout occurs #1 SLTF SCL Low Timeout Flag 3 1 read-write 0 No low timeout occurs #0 1 Low timeout occurs #1 TCKSEL Timeout Counter Clock Select 4 1 read-write 0 Timeout counter counts at the frequency of the I2C module clock / 64 #0 1 Timeout counter counts at the frequency of the I2C module clock #1 SIICAEN Second I2C Address Enable 5 1 read-write 0 I2C address register 2 matching is disabled #0 1 I2C address register 2 matching is enabled #1 ALERTEN SMBus Alert Response Address Enable 6 1 read-write 0 SMBus alert response address matching is disabled #0 1 SMBus alert response address matching is enabled #1 FACK Fast NACK/ACK Enable 7 1 read-write 0 An ACK or NACK is sent on the following receiving data byte #0 1 Writing 0 to TXAK after receiving a data byte generates an ACK. Writing 1 to TXAK after receiving a data byte generates a NACK. #1 A2 I2C Address Register 2 0x9 8 read-write 0xC2 0xFF SAD SMBus Address 1 7 read-write SLTH I2C SCL Low Timeout Register High 0xA 8 read-write 0 0xFF SSLT Most significant byte of SCL low timeout value that determines the timeout period of SCL low. 0 8 read-write SLTL I2C SCL Low Timeout Register Low 0xB 8 read-write 0 0xFF SSLT Least significant byte of SCL low timeout value that determines the timeout period of SCL low. 0 8 read-write UART0 Universal Asynchronous Receiver/Transmitter UART0_ 0x4006A000 0 0xC registers UART0 12 BDH UART Baud Rate Register High 0 8 read-write 0 0xFF SBR Baud Rate Modulo Divisor. 0 5 read-write SBNS Stop Bit Number Select 5 1 read-write 0 One stop bit. #0 1 Two stop bit. #1 RXEDGIE RX Input Active Edge Interrupt Enable (for RXEDGIF) 6 1 read-write 0 Hardware interrupts from UART_S2[RXEDGIF] disabled (use polling). #0 1 Hardware interrupt requested when UART_S2[RXEDGIF] flag is 1. #1 LBKDIE LIN Break Detect Interrupt Enable (for LBKDIF) 7 1 read-write 0 Hardware interrupts from UART_S2[LBKDIF] disabled (use polling). #0 1 Hardware interrupt requested when UART_S2[LBKDIF] flag is 1. #1 BDL UART Baud Rate Register Low 0x1 8 read-write 0x4 0xFF SBR Baud Rate Modulo Divisor 0 8 read-write C1 UART Control Register 1 0x2 8 read-write 0 0xFF PT Parity Type 0 1 read-write 0 Even parity. #0 1 Odd parity. #1 PE Parity Enable 1 1 read-write 0 No hardware parity generation or checking. #0 1 Parity enabled. #1 ILT Idle Line Type Select 2 1 read-write 0 Idle character bit count starts after start bit. #0 1 Idle character bit count starts after stop bit. #1 WAKE Receiver Wakeup Method Select 3 1 read-write 0 Idle-line wakeup. #0 1 Address-mark wakeup. #1 M 9-Bit or 8-Bit Mode Select 4 1 read-write 0 Receiver and transmitter use 8-bit data characters. #0 1 Receiver and transmitter use 9-bit data characters. #1 RSRC Receiver Source Select 5 1 read-write 0 Provided LOOPS is set, RSRC is cleared, selects internal loop back mode and the UART does not use the UART_RX pins. #0 1 Single-wire UART mode where the UART_TX pin is connected to the transmitter output and receiver input. #1 DOZEEN Doze Enable 6 1 read-write 0 UART is enabled in Wait mode. #0 1 UART is disabled in Wait mode. #1 LOOPS Loop Mode Select 7 1 read-write 0 Normal operation - UART_RX and UART_TX use separate pins. #0 1 Loop mode or single-wire mode where transmitter outputs are internally connected to receiver input. (See RSRC bit.) UART_RX pin is not used by UART. #1 C2 UART Control Register 2 0x3 8 read-write 0 0xFF SBK Send Break 0 1 read-write 0 Normal transmitter operation. #0 1 Queue break character(s) to be sent. #1 RWU Receiver Wakeup Control 1 1 read-write 0 Normal UART receiver operation. #0 1 UART receiver in standby waiting for wakeup condition. #1 RE Receiver Enable 2 1 read-write 0 Receiver disabled. #0 1 Receiver enabled. #1 TE Transmitter Enable 3 1 read-write 0 Transmitter disabled. #0 1 Transmitter enabled. #1 ILIE Idle Line Interrupt Enable for IDLE 4 1 read-write 0 Hardware interrupts from IDLE disabled; use polling. #0 1 Hardware interrupt requested when IDLE flag is 1. #1 RIE Receiver Interrupt Enable for RDRF 5 1 read-write 0 Hardware interrupts from RDRF disabled; use polling. #0 1 Hardware interrupt requested when RDRF flag is 1. #1 TCIE Transmission Complete Interrupt Enable for TC 6 1 read-write 0 Hardware interrupts from TC disabled; use polling. #0 1 Hardware interrupt requested when TC flag is 1. #1 TIE Transmit Interrupt Enable for TDRE 7 1 read-write 0 Hardware interrupts from TDRE disabled; use polling. #0 1 Hardware interrupt requested when TDRE flag is 1. #1 S1 UART Status Register 1 0x4 8 read-write 0xC0 0xFF PF Parity Error Flag 0 1 read-write 0 No parity error. #0 1 Parity error. #1 FE Framing Error Flag 1 1 read-write 0 No framing error detected. This does not guarantee the framing is correct. #0 1 Framing error. #1 NF Noise Flag 2 1 read-write 0 No noise detected. #0 1 Noise detected in the received character in UART_D. #1 OR Receiver Overrun Flag 3 1 read-write 0 No overrun. #0 1 Receive overrun (new UART data lost). #1 IDLE Idle Line Flag 4 1 read-write 0 No idle line detected. #0 1 Idle line was detected. #1 RDRF Receive Data Register Full Flag 5 1 read-only 0 Receive data buffer empty. #0 1 Receive data buffer full. #1 TC Transmission Complete Flag 6 1 read-only 0 Transmitter active (sending data, a preamble, or a break). #0 1 Transmitter idle (transmission activity complete). #1 TDRE Transmit Data Register Empty Flag 7 1 read-only 0 Transmit data buffer full. #0 1 Transmit data buffer empty. #1 S2 UART Status Register 2 0x5 8 read-write 0 0xFF RAF Receiver Active Flag 0 1 read-only 0 UART receiver idle waiting for a start bit. #0 1 UART receiver active ( UART_RXD input not idle). #1 LBKDE LIN Break Detection Enable 1 1 read-write 0 Break character is detected at length 10 bit times (if M = 0, SBNS = 0) or 11 (if M = 1, SBNS = 0 or M = 0, SBNS = 1) or 12 (if M = 1, SBNS = 1 or M10 = 1, SNBS = 0) or 13 (if M10 = 1, SNBS = 1). #0 1 Break character is detected at length of 11 bit times (if M = 0, SBNS = 0) or 12 (if M = 1, SBNS = 0 or M = 0, SBNS = 1) or 14 (if M = 1, SBNS = 1 or M10 = 1, SNBS = 0) or 15 (if M10 = 1, SNBS = 1). #1 BRK13 Break Character Generation Length 2 1 read-write 0 Break character is transmitted with length of 10 bit times (if M = 0, SBNS = 0) or 11 (if M = 1, SBNS = 0 or M = 0, SBNS = 1) or 12 (if M = 1, SBNS = 1 or M10 = 1, SNBS = 0) or 13 (if M10 = 1, SNBS = 1). #0 1 Break character is transmitted with length of 13 bit times (if M = 0, SBNS = 0) or 14 (if M = 1, SBNS = 0 or M = 0, SBNS = 1) or 15 (if M = 1, SBNS = 1 or M10 = 1, SNBS = 0) or 16 (if M10 = 1, SNBS = 1). #1 RWUID Receive Wake Up Idle Detect 3 1 read-write 0 During receive standby state (RWU = 1), the IDLE bit does not get set upon detection of an idle character. #0 1 During receive standby state (RWU = 1), the IDLE bit gets set upon detection of an idle character. #1 RXINV Receive Data Inversion 4 1 read-write 0 Receive data not inverted. #0 1 Receive data inverted. #1 MSBF MSB First 5 1 read-write 0 LSB (bit0) is the first bit that is transmitted following the start bit. Further, the first bit received after the start bit is identified as bit0. #0 1 MSB (bit9, bit8, bit7 or bit6) is the first bit that is transmitted following the start bit depending on the setting of C1[M], C1[PE] and C4[M10]. Further, the first bit received after the start bit is identified as bit9, bit8, bit7 or bit6 depending on the setting of C1[M] and C1[PE]. #1 RXEDGIF UART_RX Pin Active Edge Interrupt Flag 6 1 read-write 0 No active edge on the receive pin has occurred. #0 1 An active edge on the receive pin has occurred. #1 LBKDIF LIN Break Detect Interrupt Flag 7 1 read-write 0 No LIN break character has been detected. #0 1 LIN break character has been detected. #1 C3 UART Control Register 3 0x6 8 read-write 0 0xFF PEIE Parity Error Interrupt Enable 0 1 read-write 0 PF interrupts disabled; use polling). #0 1 Hardware interrupt requested when PF is set. #1 FEIE Framing Error Interrupt Enable 1 1 read-write 0 FE interrupts disabled; use polling. #0 1 Hardware interrupt requested when FE is set. #1 NEIE Noise Error Interrupt Enable 2 1 read-write 0 NF interrupts disabled; use polling. #0 1 Hardware interrupt requested when NF is set. #1 ORIE Overrun Interrupt Enable 3 1 read-write 0 OR interrupts disabled; use polling. #0 1 Hardware interrupt requested when OR is set. #1 TXINV Transmit Data Inversion 4 1 read-write 0 Transmit data not inverted. #0 1 Transmit data inverted. #1 TXDIR UART_TX Pin Direction in Single-Wire Mode 5 1 read-write 0 UART_TXD pin is an input in single-wire mode. #0 1 UART_TXD pin is an output in single-wire mode. #1 R9T8 Receive Bit 9 / Transmit Bit 8 6 1 read-write R8T9 Receive Bit 8 / Transmit Bit 9 7 1 read-write D UART Data Register 0x7 8 read-write 0 0xFF R0T0 Read receive data buffer 0 or write transmit data buffer 0. 0 1 read-write R1T1 Read receive data buffer 1 or write transmit data buffer 1. 1 1 read-write R2T2 Read receive data buffer 2 or write transmit data buffer 2. 2 1 read-write R3T3 Read receive data buffer 3 or write transmit data buffer 3. 3 1 read-write R4T4 Read receive data buffer 4 or write transmit data buffer 4. 4 1 read-write R5T5 Read receive data buffer 5 or write transmit data buffer 5. 5 1 read-write R6T6 Read receive data buffer 6 or write transmit data buffer 6. 6 1 read-write R7T7 Read receive data buffer 7 or write transmit data buffer 7. 7 1 read-write MA1 UART Match Address Registers 1 0x8 8 read-write 0 0xFF MA Match Address 0 8 read-write MA2 UART Match Address Registers 2 0x9 8 read-write 0 0xFF MA Match Address 0 8 read-write C4 UART Control Register 4 0xA 8 read-write 0xF 0xFF OSR Over Sampling Ratio 0 5 read-write M10 10-bit Mode select 5 1 read-write 0 Receiver and transmitter use 8-bit or 9-bit data characters. #0 1 Receiver and transmitter use 10-bit data characters. #1 MAEN2 Match Address Mode Enable 2 6 1 read-write 0 All data received is transferred to the data buffer if MAEN1 is cleared. #0 1 All data received with the most significant bit cleared, is discarded. All data received with the most significant bit set, is compared with contents of MA2 register. If no match occurs, the data is discarded. If match occurs, data is transferred to the data buffer. #1 MAEN1 Match Address Mode Enable 1 7 1 read-write 0 All data received is transferred to the data buffer if MAEN2 is cleared. #0 1 All data received with the most significant bit cleared, is discarded. All data received with the most significant bit set, is compared with contents of MA1 register. If no match occurs, the data is discarded. If match occurs, data is transferred to the data buffer. #1 C5 UART Control Register 5 0xB 8 read-write 0 0xFF RESYNCDIS Resynchronization Disable 0 1 read-write 0 Resynchronization during received data word is supported #0 1 Resynchronization during received data word is disabled #1 BOTHEDGE Both Edge Sampling 1 1 read-write 0 Receiver samples input data using the rising edge of the baud rate clock. #0 1 Receiver samples input data using the rising and falling edge of the baud rate clock. #1 RDMAE Receiver Full DMA Enable 5 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 TDMAE Transmitter DMA Enable 7 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 UART1 Universal Asynchronous Receiver/Transmitter (UART) UART UART1_ 0x4006B000 0 0x9 registers UART1 13 BDH UART Baud Rate Register: High 0 8 read-write 0 0xFF SBR Baud Rate Modulo Divisor. 0 5 read-write SBNS Stop Bit Number Select 5 1 read-write 0 One stop bit. #0 1 Two stop bit. #1 RXEDGIE RxD Input Active Edge Interrupt Enable (for RXEDGIF) 6 1 read-write 0 Hardware interrupts from UART_S2[RXEDGIF] disabled (use polling). #0 1 Hardware interrupt requested when UART_S2[RXEDGIF] flag is 1. #1 LBKDIE LIN Break Detect Interrupt Enable (for LBKDIF) 7 1 read-write 0 Hardware interrupts from UART_S2[LBKDIF] disabled (use polling). #0 1 Hardware interrupt requested when UART_S2[LBKDIF] flag is 1. #1 BDL UART Baud Rate Register: Low 0x1 8 read-write 0x4 0xFF SBR Baud Rate Modulo Divisor 0 8 read-write C1 UART Control Register 1 0x2 8 read-write 0 0xFF PT Parity Type 0 1 read-write 0 Even parity. #0 1 Odd parity. #1 PE Parity Enable 1 1 read-write 0 No hardware parity generation or checking. #0 1 Parity enabled. #1 ILT Idle Line Type Select 2 1 read-write 0 Idle character bit count starts after start bit. #0 1 Idle character bit count starts after stop bit. #1 WAKE Receiver Wakeup Method Select 3 1 read-write 0 Idle-line wake-up. #0 1 Address-mark wake-up. #1 M 9-Bit or 8-Bit Mode Select 4 1 read-write 0 Normal - start + 8 data bits (lsb first) + stop. #0 1 Receiver and transmitter use 9-bit data characters start + 8 data bits (lsb first) + 9th data bit + stop. #1 RSRC Receiver Source Select 5 1 read-write 0 Provided LOOPS is set, RSRC is cleared, selects internal loop back mode and the UART does not use the RxD pins. #0 1 Single-wire UART mode where the TxD pin is connected to the transmitter output and receiver input. #1 UARTSWAI UART Stops in Wait Mode 6 1 read-write 0 UART clocks continue to run in Wait mode so the UART can be the source of an interrupt that wakes up the CPU. #0 1 UART clocks freeze while CPU is in Wait mode. #1 LOOPS Loop Mode Select 7 1 read-write 0 Normal operation - RxD and TxD use separate pins. #0 1 Loop mode or single-wire mode where transmitter outputs are internally connected to receiver input. (See RSRC bit.) RxD pin is not used by UART. #1 C2 UART Control Register 2 0x3 8 read-write 0 0xFF SBK Send Break 0 1 read-write 0 Normal transmitter operation. #0 1 Queue break character(s) to be sent. #1 RWU Receiver Wakeup Control 1 1 read-write 0 Normal UART receiver operation. #0 1 UART receiver in standby waiting for wake-up condition. #1 RE Receiver Enable 2 1 read-write 0 Receiver off. #0 1 Receiver on. #1 TE Transmitter Enable 3 1 read-write 0 Transmitter off. #0 1 Transmitter on. #1 ILIE Idle Line Interrupt Enable for IDLE 4 1 read-write 0 Hardware interrupts from S1[IDLE] disabled; use polling. #0 1 Hardware interrupt requested when S1[IDLE] flag is 1. #1 RIE Receiver Interrupt Enable for RDRF 5 1 read-write 0 Hardware interrupts from S1[RDRF] disabled; use polling. #0 1 Hardware interrupt requested when S1[RDRF] flag is 1. #1 TCIE Transmission Complete Interrupt Enable for TC 6 1 read-write 0 Hardware interrupts from TC disabled; use polling. #0 1 Hardware interrupt requested when TC flag is 1. #1 TIE Transmit Interrupt Enable for TDRE 7 1 read-write 0 Hardware interrupts from TDRE disabled; use polling. #0 1 Hardware interrupt requested when TDRE flag is 1. #1 S1 UART Status Register 1 0x4 8 read-only 0xC0 0xFF PF Parity Error Flag 0 1 read-only 0 No parity error. #0 1 Parity error. #1 FE Framing Error Flag 1 1 read-only 0 No framing error detected. This does not guarantee the framing is correct. #0 1 Framing error. #1 NF Noise Flag 2 1 read-only 0 No noise detected. #0 1 Noise detected in the received character in UART_D. #1 OR Receiver Overrun Flag 3 1 read-only 0 No overrun. #0 1 Receive overrun (new UART data lost). #1 IDLE Idle Line Flag 4 1 read-only 0 No idle line detected. #0 1 Idle line was detected. #1 RDRF Receive Data Register Full Flag 5 1 read-only 0 Receive data register empty. #0 1 Receive data register full. #1 TC Transmission Complete Flag 6 1 read-only 0 Transmitter active (sending data, a preamble, or a break). #0 1 Transmitter idle (transmission activity complete). #1 TDRE Transmit Data Register Empty Flag 7 1 read-only 0 Transmit data register (buffer) full. #0 1 Transmit data register (buffer) empty. #1 S2 UART Status Register 2 0x5 8 read-write 0 0xFF RAF Receiver Active Flag 0 1 read-only 0 UART receiver idle waiting for a start bit. #0 1 UART receiver active (RxD input not idle). #1 LBKDE LIN Break Detection Enable 1 1 read-write 0 Break detection is disabled. #0 1 Break detection is enabled (Break character is detected at length 11 bit times (if C1[M] = 0, BDH[SBNS] = 0) or 12 (if C1[M] = 1, BDH[SBNS] = 0 or C1[M] = 0, BDH[SBNS] = 1) or 13 (if C1[M] = 1, BDH[SBNS] = 1)). #1 BRK13 Break Character Generation Length 2 1 read-write 0 Break character is transmitted with length of 10 bit times (if M = 0, SBNS = 0) or 11 (if M = 1, SBNS = 0 or M = 0, SBNS = 1) or 12 (if M = 1, SBNS = 1). #0 1 Break character is transmitted with length of 13 bit times (if M = 0, SBNS = 0) or 14 (if M = 1, SBNS = 0 or M = 0, SBNS = 1) or 15 (if M = 1, SBNS = 1). #1 RWUID Receive Wake Up Idle Detect 3 1 read-write 0 During receive standby state (RWU = 1), S1[IDLE] does not get set upon detection of an idle character. #0 1 During receive standby state (RWU = 1), S1[IDLE] gets set upon detection of an idle character. #1 RXINV Receive Data Inversion 4 1 read-write 0 Receive data not inverted. #0 1 Receive data inverted. #1 RXEDGIF RxD Pin Active Edge Interrupt Flag 6 1 read-write 0 No active edge on the receive pin has occurred. #0 1 An active edge on the receive pin has occurred. #1 LBKDIF LIN Break Detect Interrupt Flag 7 1 read-write 0 No LIN break character has been detected. #0 1 LIN break character has been detected. #1 C3 UART Control Register 3 0x6 8 read-write 0 0xFF PEIE Parity Error Interrupt Enable 0 1 read-write 0 PF interrupts disabled; use polling). #0 1 Hardware interrupt requested when PF is set. #1 FEIE Framing Error Interrupt Enable 1 1 read-write 0 FE interrupts disabled; use polling). #0 1 Hardware interrupt requested when FE is set. #1 NEIE Noise Error Interrupt Enable 2 1 read-write 0 NF interrupts disabled; use polling). #0 1 Hardware interrupt requested when NF is set. #1 ORIE Overrun Interrupt Enable 3 1 read-write 0 OR interrupts disabled; use polling. #0 1 Hardware interrupt requested when OR is set. #1 TXINV Transmit Data Inversion 4 1 read-write 0 Transmit data not inverted. #0 1 Transmit data inverted. #1 TXDIR TxD Pin Direction in Single-Wire Mode 5 1 read-write 0 TxD pin is an input in single-wire mode. #0 1 TxD pin is an output in single-wire mode. #1 T8 Ninth Data Bit for Transmitter 6 1 read-write R8 Ninth Data Bit for Receiver 7 1 read-only D UART Data Register 0x7 8 read-write 0 0xFF R0T0 Read receive data buffer 0 or write transmit data buffer 0. 0 1 read-write R1T1 Read receive data buffer 1 or write transmit data buffer 1. 1 1 read-write R2T2 Read receive data buffer 2 or write transmit data buffer 2. 2 1 read-write R3T3 Read receive data buffer 3 or write transmit data buffer 3. 3 1 read-write R4T4 Read receive data buffer 4 or write transmit data buffer 4. 4 1 read-write R5T5 Read receive data buffer 5 or write transmit data buffer 5. 5 1 read-write R6T6 Read receive data buffer 6 or write transmit data buffer 6. 6 1 read-write R7T7 Read receive data buffer 7 or write transmit data buffer 7. 7 1 read-write C4 UART Control Register 4 0x8 8 read-write 0 0xFF RDMAS Receiver Full DMA Select 5 1 read-write 0 If RIE is set and the RDRF flag is set, the RDRF interrupt request signal is asserted to request interrupt service. #0 1 If RIE is set and the RDRF flag is set, the RDRF DMA request signal is asserted to request a DMA transfer. #1 TDMAS Transmitter DMA Select 7 1 read-write 0 If TIE is set and the TDRE flag is set, the TDRE interrupt request signal is asserted to request interrupt service. #0 1 If TIE is set and the TDRE flag is set, the TDRE DMA request signal is asserted to request a DMA transfer. #1 UART2 Universal Asynchronous Receiver/Transmitter (UART) UART UART2_ 0x4006C000 0 0x9 registers UART2 14 BDH UART Baud Rate Register: High 0 8 read-write 0 0xFF SBR Baud Rate Modulo Divisor. 0 5 read-write SBNS Stop Bit Number Select 5 1 read-write 0 One stop bit. #0 1 Two stop bit. #1 RXEDGIE RxD Input Active Edge Interrupt Enable (for RXEDGIF) 6 1 read-write 0 Hardware interrupts from UART_S2[RXEDGIF] disabled (use polling). #0 1 Hardware interrupt requested when UART_S2[RXEDGIF] flag is 1. #1 LBKDIE LIN Break Detect Interrupt Enable (for LBKDIF) 7 1 read-write 0 Hardware interrupts from UART_S2[LBKDIF] disabled (use polling). #0 1 Hardware interrupt requested when UART_S2[LBKDIF] flag is 1. #1 BDL UART Baud Rate Register: Low 0x1 8 read-write 0x4 0xFF SBR Baud Rate Modulo Divisor 0 8 read-write C1 UART Control Register 1 0x2 8 read-write 0 0xFF PT Parity Type 0 1 read-write 0 Even parity. #0 1 Odd parity. #1 PE Parity Enable 1 1 read-write 0 No hardware parity generation or checking. #0 1 Parity enabled. #1 ILT Idle Line Type Select 2 1 read-write 0 Idle character bit count starts after start bit. #0 1 Idle character bit count starts after stop bit. #1 WAKE Receiver Wakeup Method Select 3 1 read-write 0 Idle-line wake-up. #0 1 Address-mark wake-up. #1 M 9-Bit or 8-Bit Mode Select 4 1 read-write 0 Normal - start + 8 data bits (lsb first) + stop. #0 1 Receiver and transmitter use 9-bit data characters start + 8 data bits (lsb first) + 9th data bit + stop. #1 RSRC Receiver Source Select 5 1 read-write 0 Provided LOOPS is set, RSRC is cleared, selects internal loop back mode and the UART does not use the RxD pins. #0 1 Single-wire UART mode where the TxD pin is connected to the transmitter output and receiver input. #1 UARTSWAI UART Stops in Wait Mode 6 1 read-write 0 UART clocks continue to run in Wait mode so the UART can be the source of an interrupt that wakes up the CPU. #0 1 UART clocks freeze while CPU is in Wait mode. #1 LOOPS Loop Mode Select 7 1 read-write 0 Normal operation - RxD and TxD use separate pins. #0 1 Loop mode or single-wire mode where transmitter outputs are internally connected to receiver input. (See RSRC bit.) RxD pin is not used by UART. #1 C2 UART Control Register 2 0x3 8 read-write 0 0xFF SBK Send Break 0 1 read-write 0 Normal transmitter operation. #0 1 Queue break character(s) to be sent. #1 RWU Receiver Wakeup Control 1 1 read-write 0 Normal UART receiver operation. #0 1 UART receiver in standby waiting for wake-up condition. #1 RE Receiver Enable 2 1 read-write 0 Receiver off. #0 1 Receiver on. #1 TE Transmitter Enable 3 1 read-write 0 Transmitter off. #0 1 Transmitter on. #1 ILIE Idle Line Interrupt Enable for IDLE 4 1 read-write 0 Hardware interrupts from S1[IDLE] disabled; use polling. #0 1 Hardware interrupt requested when S1[IDLE] flag is 1. #1 RIE Receiver Interrupt Enable for RDRF 5 1 read-write 0 Hardware interrupts from S1[RDRF] disabled; use polling. #0 1 Hardware interrupt requested when S1[RDRF] flag is 1. #1 TCIE Transmission Complete Interrupt Enable for TC 6 1 read-write 0 Hardware interrupts from TC disabled; use polling. #0 1 Hardware interrupt requested when TC flag is 1. #1 TIE Transmit Interrupt Enable for TDRE 7 1 read-write 0 Hardware interrupts from TDRE disabled; use polling. #0 1 Hardware interrupt requested when TDRE flag is 1. #1 S1 UART Status Register 1 0x4 8 read-only 0xC0 0xFF PF Parity Error Flag 0 1 read-only 0 No parity error. #0 1 Parity error. #1 FE Framing Error Flag 1 1 read-only 0 No framing error detected. This does not guarantee the framing is correct. #0 1 Framing error. #1 NF Noise Flag 2 1 read-only 0 No noise detected. #0 1 Noise detected in the received character in UART_D. #1 OR Receiver Overrun Flag 3 1 read-only 0 No overrun. #0 1 Receive overrun (new UART data lost). #1 IDLE Idle Line Flag 4 1 read-only 0 No idle line detected. #0 1 Idle line was detected. #1 RDRF Receive Data Register Full Flag 5 1 read-only 0 Receive data register empty. #0 1 Receive data register full. #1 TC Transmission Complete Flag 6 1 read-only 0 Transmitter active (sending data, a preamble, or a break). #0 1 Transmitter idle (transmission activity complete). #1 TDRE Transmit Data Register Empty Flag 7 1 read-only 0 Transmit data register (buffer) full. #0 1 Transmit data register (buffer) empty. #1 S2 UART Status Register 2 0x5 8 read-write 0 0xFF RAF Receiver Active Flag 0 1 read-only 0 UART receiver idle waiting for a start bit. #0 1 UART receiver active (RxD input not idle). #1 LBKDE LIN Break Detection Enable 1 1 read-write 0 Break detection is disabled. #0 1 Break detection is enabled (Break character is detected at length 11 bit times (if C1[M] = 0, BDH[SBNS] = 0) or 12 (if C1[M] = 1, BDH[SBNS] = 0 or C1[M] = 0, BDH[SBNS] = 1) or 13 (if C1[M] = 1, BDH[SBNS] = 1)). #1 BRK13 Break Character Generation Length 2 1 read-write 0 Break character is transmitted with length of 10 bit times (if M = 0, SBNS = 0) or 11 (if M = 1, SBNS = 0 or M = 0, SBNS = 1) or 12 (if M = 1, SBNS = 1). #0 1 Break character is transmitted with length of 13 bit times (if M = 0, SBNS = 0) or 14 (if M = 1, SBNS = 0 or M = 0, SBNS = 1) or 15 (if M = 1, SBNS = 1). #1 RWUID Receive Wake Up Idle Detect 3 1 read-write 0 During receive standby state (RWU = 1), S1[IDLE] does not get set upon detection of an idle character. #0 1 During receive standby state (RWU = 1), S1[IDLE] gets set upon detection of an idle character. #1 RXINV Receive Data Inversion 4 1 read-write 0 Receive data not inverted. #0 1 Receive data inverted. #1 RXEDGIF RxD Pin Active Edge Interrupt Flag 6 1 read-write 0 No active edge on the receive pin has occurred. #0 1 An active edge on the receive pin has occurred. #1 LBKDIF LIN Break Detect Interrupt Flag 7 1 read-write 0 No LIN break character has been detected. #0 1 LIN break character has been detected. #1 C3 UART Control Register 3 0x6 8 read-write 0 0xFF PEIE Parity Error Interrupt Enable 0 1 read-write 0 PF interrupts disabled; use polling). #0 1 Hardware interrupt requested when PF is set. #1 FEIE Framing Error Interrupt Enable 1 1 read-write 0 FE interrupts disabled; use polling). #0 1 Hardware interrupt requested when FE is set. #1 NEIE Noise Error Interrupt Enable 2 1 read-write 0 NF interrupts disabled; use polling). #0 1 Hardware interrupt requested when NF is set. #1 ORIE Overrun Interrupt Enable 3 1 read-write 0 OR interrupts disabled; use polling. #0 1 Hardware interrupt requested when OR is set. #1 TXINV Transmit Data Inversion 4 1 read-write 0 Transmit data not inverted. #0 1 Transmit data inverted. #1 TXDIR TxD Pin Direction in Single-Wire Mode 5 1 read-write 0 TxD pin is an input in single-wire mode. #0 1 TxD pin is an output in single-wire mode. #1 T8 Ninth Data Bit for Transmitter 6 1 read-write R8 Ninth Data Bit for Receiver 7 1 read-only D UART Data Register 0x7 8 read-write 0 0xFF R0T0 Read receive data buffer 0 or write transmit data buffer 0. 0 1 read-write R1T1 Read receive data buffer 1 or write transmit data buffer 1. 1 1 read-write R2T2 Read receive data buffer 2 or write transmit data buffer 2. 2 1 read-write R3T3 Read receive data buffer 3 or write transmit data buffer 3. 3 1 read-write R4T4 Read receive data buffer 4 or write transmit data buffer 4. 4 1 read-write R5T5 Read receive data buffer 5 or write transmit data buffer 5. 5 1 read-write R6T6 Read receive data buffer 6 or write transmit data buffer 6. 6 1 read-write R7T7 Read receive data buffer 7 or write transmit data buffer 7. 7 1 read-write C4 UART Control Register 4 0x8 8 read-write 0 0xFF RDMAS Receiver Full DMA Select 5 1 read-write 0 If RIE is set and the RDRF flag is set, the RDRF interrupt request signal is asserted to request interrupt service. #0 1 If RIE is set and the RDRF flag is set, the RDRF DMA request signal is asserted to request a DMA transfer. #1 TDMAS Transmitter DMA Select 7 1 read-write 0 If TIE is set and the TDRE flag is set, the TDRE interrupt request signal is asserted to request interrupt service. #0 1 If TIE is set and the TDRE flag is set, the TDRE DMA request signal is asserted to request a DMA transfer. #1 CMP0 High-Speed Comparator (CMP), Voltage Reference (VREF) Digital-to-Analog Converter (DAC), and Analog Mux (ANMUX) CMP0_ 0x40073000 0 0x6 registers CMP0 16 CR0 CMP Control Register 0 0 8 read-write 0 0xFF HYSTCTR Comparator hard block hysteresis control 0 2 read-write 00 Level 0 #00 01 Level 1 #01 10 Level 2 #10 11 Level 3 #11 FILTER_CNT Filter Sample Count 4 3 read-write 000 Filter is disabled. If SE = 1, then COUT is a logic 0. This is not a legal state, and is not recommended. If SE = 0, COUT = COUTA. #000 001 One sample must agree. The comparator output is simply sampled. #001 010 2 consecutive samples must agree. #010 011 3 consecutive samples must agree. #011 100 4 consecutive samples must agree. #100 101 5 consecutive samples must agree. #101 110 6 consecutive samples must agree. #110 111 7 consecutive samples must agree. #111 CR1 CMP Control Register 1 0x1 8 read-write 0 0xFF EN Comparator Module Enable 0 1 read-write 0 Analog Comparator is disabled. #0 1 Analog Comparator is enabled. #1 OPE Comparator Output Pin Enable 1 1 read-write 0 CMPO is not available on the associated CMPO output pin. If the comparator does not own the pin, this field has no effect. #0 1 CMPO is available on the associated CMPO output pin. The comparator output (CMPO) is driven out on the associated CMPO output pin if the comparator owns the pin. If the comparator does not own the field, this bit has no effect. #1 COS Comparator Output Select 2 1 read-write 0 Set the filtered comparator output (CMPO) to equal COUT. #0 1 Set the unfiltered comparator output (CMPO) to equal COUTA. #1 INV Comparator INVERT 3 1 read-write 0 Does not invert the comparator output. #0 1 Inverts the comparator output. #1 PMODE Power Mode Select 4 1 read-write 0 Low-Speed (LS) Comparison mode selected. In this mode, CMP has slower output propagation delay and lower current consumption. #0 1 High-Speed (HS) Comparison mode selected. In this mode, CMP has faster output propagation delay and higher current consumption. #1 TRIGM Trigger Mode Enable 5 1 read-write 0 Trigger mode is disabled. #0 1 Trigger mode is enabled. #1 WE Windowing Enable 6 1 read-write 0 Windowing mode is not selected. #0 1 Windowing mode is selected. #1 SE Sample Enable 7 1 read-write 0 Sampling mode is not selected. #0 1 Sampling mode is selected. #1 FPR CMP Filter Period Register 0x2 8 read-write 0 0xFF FILT_PER Filter Sample Period 0 8 read-write SCR CMP Status and Control Register 0x3 8 read-write 0 0xFF COUT Analog Comparator Output 0 1 read-only CFF Analog Comparator Flag Falling 1 1 read-write 0 Falling-edge on COUT has not been detected. #0 1 Falling-edge on COUT has occurred. #1 CFR Analog Comparator Flag Rising 2 1 read-write 0 Rising-edge on COUT has not been detected. #0 1 Rising-edge on COUT has occurred. #1 IEF Comparator Interrupt Enable Falling 3 1 read-write 0 Interrupt is disabled. #0 1 Interrupt is enabled. #1 IER Comparator Interrupt Enable Rising 4 1 read-write 0 Interrupt is disabled. #0 1 Interrupt is enabled. #1 DMAEN DMA Enable Control 6 1 read-write 0 DMA is disabled. #0 1 DMA is enabled. #1 DACCR DAC Control Register 0x4 8 read-write 0 0xFF VOSEL DAC Output Voltage Select 0 6 read-write VRSEL Supply Voltage Reference Source Select 6 1 read-write 0 V is selected as resistor ladder network supply reference V. in1 in #0 1 V is selected as resistor ladder network supply reference V. in2 in #1 DACEN DAC Enable 7 1 read-write 0 DAC is disabled. #0 1 DAC is enabled. #1 MUXCR MUX Control Register 0x5 8 read-write 0 0xFF MSEL Minus Input Mux Control 0 3 read-write 000 IN0 #000 001 IN1 #001 010 IN2 #010 011 IN3 #011 100 IN4 #100 101 IN5 #101 110 IN6 #110 111 IN7 #111 PSEL Plus Input Mux Control 3 3 read-write 000 IN0 #000 001 IN1 #001 010 IN2 #010 011 IN3 #011 100 IN4 #100 101 IN5 #101 110 IN6 #110 111 IN7 #111 PSTM Pass Through Mode Enable 7 1 read-write 0 Pass Through Mode is disabled. #0 1 Pass Through Mode is enabled. #1 SPI0 Serial Peripheral Interface SPI SPI0_ 0x40076000 0 0x8 registers SPI0 10 S SPI Status Register 0 8 read-write 0x20 0xFF MODF Master Mode Fault Flag 4 1 read-only 0 No mode fault error #0 1 Mode fault error detected #1 SPTEF SPI Transmit Buffer Empty Flag (when FIFO is not supported or not enabled) or SPI transmit FIFO empty flag (when FIFO is supported and enabled) 5 1 read-only 0 SPI transmit buffer not empty (when FIFOMODE is not present or is 0) or SPI FIFO not empty (when FIFOMODE is 1) #0 1 SPI transmit buffer empty (when FIFOMODE is not present or is 0) or SPI FIFO empty (when FIFOMODE is 1) #1 SPMF SPI Match Flag 6 1 read-write 0 Value in the receive data buffer does not match the value in the MH:ML registers #0 1 Value in the receive data buffer matches the value in the MH:ML registers #1 SPRF SPI Read Buffer Full Flag (when FIFO is not supported or not enabled) or SPI read FIFO FULL flag (when FIFO is supported and enabled) 7 1 read-only 0 No data available in the receive data buffer (when FIFOMODE is not present or is 0) or Read FIFO is not full (when FIFOMODE is 1) #0 1 Data available in the receive data buffer (when FIFOMODE is not present or is 0) or Read FIFO is full (when FIFOMODE is 1) #1 BR SPI Baud Rate Register 0x1 8 read-write 0 0xFF SPR SPI Baud Rate Divisor 0 4 read-write 0000 Baud rate divisor is 2. #0000 0001 Baud rate divisor is 4. #0001 0010 Baud rate divisor is 8. #0010 0011 Baud rate divisor is 16. #0011 0100 Baud rate divisor is 32. #0100 0101 Baud rate divisor is 64. #0101 0110 Baud rate divisor is 128. #0110 0111 Baud rate divisor is 256. #0111 1000 Baud rate divisor is 512. #1000 SPPR SPI Baud Rate Prescale Divisor 4 3 read-write 000 Baud rate prescaler divisor is 1. #000 001 Baud rate prescaler divisor is 2. #001 010 Baud rate prescaler divisor is 3. #010 011 Baud rate prescaler divisor is 4. #011 100 Baud rate prescaler divisor is 5. #100 101 Baud rate prescaler divisor is 6. #101 110 Baud rate prescaler divisor is 7. #110 111 Baud rate prescaler divisor is 8. #111 C2 SPI Control Register 2 0x2 8 read-write 0 0xFF SPC0 SPI Pin Control 0 0 1 read-write 0 SPI uses separate pins for data input and data output (pin mode is normal). In master mode of operation: MISO is master in and MOSI is master out. In slave mode of operation: MISO is slave out and MOSI is slave in. #0 1 SPI configured for single-wire bidirectional operation (pin mode is bidirectional). In master mode of operation: MISO is not used by SPI; MOSI is master in when BIDIROE is 0 or master I/O when BIDIROE is 1. In slave mode of operation: MISO is slave in when BIDIROE is 0 or slave I/O when BIDIROE is 1; MOSI is not used by SPI. #1 SPISWAI SPI Stop in Wait Mode 1 1 read-write 0 SPI clocks continue to operate in Wait mode. #0 1 SPI clocks stop when the MCU enters Wait mode. #1 RXDMAE Receive DMA enable 2 1 read-write 0 DMA request for receive is disabled and interrupt from SPRF is allowed #0 1 DMA request for receive is enabled and interrupt from SPRF is disabled #1 BIDIROE Bidirectional Mode Output Enable 3 1 read-write 0 Output driver disabled so SPI data I/O pin acts as an input #0 1 SPI I/O pin enabled as an output #1 MODFEN Master Mode-Fault Function Enable 4 1 read-write 0 Mode fault function disabled, master SS pin reverts to general-purpose I/O not controlled by SPI #0 1 Mode fault function enabled, master SS pin acts as the mode fault input or the slave select output #1 TXDMAE Transmit DMA enable 5 1 read-write 0 DMA request for transmit is disabled and interrupt from SPTEF is allowed #0 1 DMA request for transmit is enabled and interrupt from SPTEF is disabled #1 SPIMODE SPI 8-bit or 16-bit mode 6 1 read-write 0 8-bit SPI shift register, match register, and buffers #0 1 16-bit SPI shift register, match register, and buffers #1 SPMIE SPI Match Interrupt Enable 7 1 read-write 0 Interrupts from SPMF inhibited (use polling) #0 1 When SPMF is 1, requests a hardware interrupt #1 C1 SPI Control Register 1 0x3 8 read-write 0x4 0xFF LSBFE LSB First (shifter direction) 0 1 read-write 0 SPI serial data transfers start with the most significant bit. #0 1 SPI serial data transfers start with the least significant bit. #1 SSOE Slave Select Output Enable 1 1 read-write 0 When C2[MODFEN] is 0: In master mode, SS pin function is general-purpose I/O (not SPI). In slave mode, SS pin function is slave select input. When C2[MODFEN] is 1: In master mode, SS pin function is SS input for mode fault. In slave mode, SS pin function is slave select input. #0 1 When C2[MODFEN] is 0: In master mode, SS pin function is general-purpose I/O (not SPI). In slave mode, SS pin function is slave select input. When C2[MODFEN] is 1: In master mode, SS pin function is automatic SS output. In slave mode: SS pin function is slave select input. #1 CPHA Clock Phase 2 1 read-write 0 First edge on SPSCK occurs at the middle of the first cycle of a data transfer. #0 1 First edge on SPSCK occurs at the start of the first cycle of a data transfer. #1 CPOL Clock Polarity 3 1 read-write 0 Active-high SPI clock (idles low) #0 1 Active-low SPI clock (idles high) #1 MSTR Master/Slave Mode Select 4 1 read-write 0 SPI module configured as a slave SPI device #0 1 SPI module configured as a master SPI device #1 SPTIE SPI Transmit Interrupt Enable 5 1 read-write 0 Interrupts from SPTEF inhibited (use polling) #0 1 When SPTEF is 1, hardware interrupt requested #1 SPE SPI System Enable 6 1 read-write 0 SPI system inactive #0 1 SPI system enabled #1 SPIE SPI Interrupt Enable: for SPRF and MODF (when FIFO is not supported or not enabled) or for read FIFO (when FIFO is supported and enabled) 7 1 read-write 0 Interrupts from SPRF and MODF are inhibited-use polling (when FIFOMODE is not present or is 0) or Read FIFO Full Interrupts are disabled (when FIFOMODE is 1) #0 1 Request a hardware interrupt when SPRF or MODF is 1 (when FIFOMODE is not present or is 0) or Read FIFO Full Interrupts are enabled (when FIFOMODE is 1) #1 ML SPI Match Register low 0x4 8 read-write 0 0xFF Bits Hardware compare value (low byte) 0 8 read-write MH SPI match register high 0x5 8 read-write 0 0xFF Bits Hardware compare value (high byte) 0 8 read-write DL SPI Data Register low 0x6 8 read-write 0 0xFF Bits Data (low byte) 0 8 read-write DH SPI data register high 0x7 8 read-write 0 0xFF Bits Data (high byte) 0 8 read-write SPI1 Serial Peripheral Interface SPI SPI1_ 0x40077000 0 0xC registers SPI1 11 S SPI Status Register 0 8 read-write 0x20 0xFF RFIFOEF SPI read FIFO empty flag 0 1 read-only 0 Read FIFO has data. Reads of the DH:DL registers in 16-bit mode or the DL register in 8-bit mode will empty the read FIFO. #0 1 Read FIFO is empty. #1 TXFULLF Transmit FIFO full flag 1 1 read-only 0 Transmit FIFO has less than 8 bytes #0 1 Transmit FIFO has 8 bytes of data #1 TNEAREF Transmit FIFO nearly empty flag 2 1 read-only 0 Transmit FIFO has more than 16 bits (when C3[TNEAREF_MARK] is 0) or more than 32 bits (when C3[TNEAREF_MARK] is 1) remaining to transmit #0 1 Transmit FIFO has an amount of data equal to or less than 16 bits (when C3[TNEAREF_MARK] is 0) or 32 bits (when C3[TNEAREF_MARK] is 1) remaining to transmit #1 RNFULLF Receive FIFO nearly full flag 3 1 read-only 0 Receive FIFO has received less than 48 bits (when C3[RNFULLF_MARK] is 0) or less than 32 bits (when C3[RNFULLF_MARK] is 1) #0 1 Receive FIFO has received data of an amount equal to or greater than 48 bits (when C3[RNFULLF_MARK] is 0) or 32 bits (when C3[RNFULLF_MARK] is 1) #1 MODF Master Mode Fault Flag 4 1 read-only 0 No mode fault error #0 1 Mode fault error detected #1 SPTEF SPI Transmit Buffer Empty Flag (when FIFO is not supported or not enabled) or SPI transmit FIFO empty flag (when FIFO is supported and enabled) 5 1 read-only 0 SPI transmit buffer not empty (when FIFOMODE is not present or is 0) or SPI FIFO not empty (when FIFOMODE is 1) #0 1 SPI transmit buffer empty (when FIFOMODE is not present or is 0) or SPI FIFO empty (when FIFOMODE is 1) #1 SPMF SPI Match Flag 6 1 read-write 0 Value in the receive data buffer does not match the value in the MH:ML registers #0 1 Value in the receive data buffer matches the value in the MH:ML registers #1 SPRF SPI Read Buffer Full Flag (when FIFO is not supported or not enabled) or SPI read FIFO FULL flag (when FIFO is supported and enabled) 7 1 read-only 0 No data available in the receive data buffer (when FIFOMODE is not present or is 0) or Read FIFO is not full (when FIFOMODE is 1) #0 1 Data available in the receive data buffer (when FIFOMODE is not present or is 0) or Read FIFO is full (when FIFOMODE is 1) #1 BR SPI Baud Rate Register 0x1 8 read-write 0 0xFF SPR SPI Baud Rate Divisor 0 4 read-write 0000 Baud rate divisor is 2. #0000 0001 Baud rate divisor is 4. #0001 0010 Baud rate divisor is 8. #0010 0011 Baud rate divisor is 16. #0011 0100 Baud rate divisor is 32. #0100 0101 Baud rate divisor is 64. #0101 0110 Baud rate divisor is 128. #0110 0111 Baud rate divisor is 256. #0111 1000 Baud rate divisor is 512. #1000 SPPR SPI Baud Rate Prescale Divisor 4 3 read-write 000 Baud rate prescaler divisor is 1. #000 001 Baud rate prescaler divisor is 2. #001 010 Baud rate prescaler divisor is 3. #010 011 Baud rate prescaler divisor is 4. #011 100 Baud rate prescaler divisor is 5. #100 101 Baud rate prescaler divisor is 6. #101 110 Baud rate prescaler divisor is 7. #110 111 Baud rate prescaler divisor is 8. #111 C2 SPI Control Register 2 0x2 8 read-write 0 0xFF SPC0 SPI Pin Control 0 0 1 read-write 0 SPI uses separate pins for data input and data output (pin mode is normal). In master mode of operation: MISO is master in and MOSI is master out. In slave mode of operation: MISO is slave out and MOSI is slave in. #0 1 SPI configured for single-wire bidirectional operation (pin mode is bidirectional). In master mode of operation: MISO is not used by SPI; MOSI is master in when BIDIROE is 0 or master I/O when BIDIROE is 1. In slave mode of operation: MISO is slave in when BIDIROE is 0 or slave I/O when BIDIROE is 1; MOSI is not used by SPI. #1 SPISWAI SPI Stop in Wait Mode 1 1 read-write 0 SPI clocks continue to operate in Wait mode. #0 1 SPI clocks stop when the MCU enters Wait mode. #1 RXDMAE Receive DMA enable 2 1 read-write 0 DMA request for receive is disabled and interrupt from SPRF is allowed #0 1 DMA request for receive is enabled and interrupt from SPRF is disabled #1 BIDIROE Bidirectional Mode Output Enable 3 1 read-write 0 Output driver disabled so SPI data I/O pin acts as an input #0 1 SPI I/O pin enabled as an output #1 MODFEN Master Mode-Fault Function Enable 4 1 read-write 0 Mode fault function disabled, master SS pin reverts to general-purpose I/O not controlled by SPI #0 1 Mode fault function enabled, master SS pin acts as the mode fault input or the slave select output #1 TXDMAE Transmit DMA enable 5 1 read-write 0 DMA request for transmit is disabled and interrupt from SPTEF is allowed #0 1 DMA request for transmit is enabled and interrupt from SPTEF is disabled #1 SPIMODE SPI 8-bit or 16-bit mode 6 1 read-write 0 8-bit SPI shift register, match register, and buffers #0 1 16-bit SPI shift register, match register, and buffers #1 SPMIE SPI Match Interrupt Enable 7 1 read-write 0 Interrupts from SPMF inhibited (use polling) #0 1 When SPMF is 1, requests a hardware interrupt #1 C1 SPI Control Register 1 0x3 8 read-write 0x4 0xFF LSBFE LSB First (shifter direction) 0 1 read-write 0 SPI serial data transfers start with the most significant bit. #0 1 SPI serial data transfers start with the least significant bit. #1 SSOE Slave Select Output Enable 1 1 read-write 0 When C2[MODFEN] is 0: In master mode, SS pin function is general-purpose I/O (not SPI). In slave mode, SS pin function is slave select input. When C2[MODFEN] is 1: In master mode, SS pin function is SS input for mode fault. In slave mode, SS pin function is slave select input. #0 1 When C2[MODFEN] is 0: In master mode, SS pin function is general-purpose I/O (not SPI). In slave mode, SS pin function is slave select input. When C2[MODFEN] is 1: In master mode, SS pin function is automatic SS output. In slave mode: SS pin function is slave select input. #1 CPHA Clock Phase 2 1 read-write 0 First edge on SPSCK occurs at the middle of the first cycle of a data transfer. #0 1 First edge on SPSCK occurs at the start of the first cycle of a data transfer. #1 CPOL Clock Polarity 3 1 read-write 0 Active-high SPI clock (idles low) #0 1 Active-low SPI clock (idles high) #1 MSTR Master/Slave Mode Select 4 1 read-write 0 SPI module configured as a slave SPI device #0 1 SPI module configured as a master SPI device #1 SPTIE SPI Transmit Interrupt Enable 5 1 read-write 0 Interrupts from SPTEF inhibited (use polling) #0 1 When SPTEF is 1, hardware interrupt requested #1 SPE SPI System Enable 6 1 read-write 0 SPI system inactive #0 1 SPI system enabled #1 SPIE SPI Interrupt Enable: for SPRF and MODF (when FIFO is not supported or not enabled) or for read FIFO (when FIFO is supported and enabled) 7 1 read-write 0 Interrupts from SPRF and MODF are inhibited-use polling (when FIFOMODE is not present or is 0) or Read FIFO Full Interrupts are disabled (when FIFOMODE is 1) #0 1 Request a hardware interrupt when SPRF or MODF is 1 (when FIFOMODE is not present or is 0) or Read FIFO Full Interrupts are enabled (when FIFOMODE is 1) #1 ML SPI Match Register low 0x4 8 read-write 0 0xFF Bits Hardware compare value (low byte) 0 8 read-write MH SPI match register high 0x5 8 read-write 0 0xFF Bits Hardware compare value (high byte) 0 8 read-write DL SPI Data Register low 0x6 8 read-write 0 0xFF Bits Data (low byte) 0 8 read-write DH SPI data register high 0x7 8 read-write 0 0xFF Bits Data (high byte) 0 8 read-write CI SPI clear interrupt register 0xA 8 read-write 0 0xFF SPRFCI Receive FIFO full flag clear interrupt 0 1 write-only SPTEFCI Transmit FIFO empty flag clear interrupt 1 1 write-only RNFULLFCI Receive FIFO nearly full flag clear interrupt 2 1 write-only TNEAREFCI Transmit FIFO nearly empty flag clear interrupt 3 1 write-only RXFOF Receive FIFO overflow flag 4 1 read-only 0 Receive FIFO overflow condition has not occurred #0 1 Receive FIFO overflow condition occurred #1 TXFOF Transmit FIFO overflow flag 5 1 read-only 0 Transmit FIFO overflow condition has not occurred #0 1 Transmit FIFO overflow condition occurred #1 RXFERR Receive FIFO error flag 6 1 read-only 0 No receive FIFO error occurred #0 1 A receive FIFO error occurred #1 TXFERR Transmit FIFO error flag 7 1 read-only 0 No transmit FIFO error occurred #0 1 A transmit FIFO error occurred #1 C3 SPI control register 3 0xB 8 read-write 0 0xFF FIFOMODE FIFO mode enable 0 1 read-write 0 Buffer mode disabled #0 1 Data available in the receive data buffer #1 RNFULLIEN Receive FIFO nearly full interrupt enable 1 1 read-write 0 No interrupt upon RNFULLF being set #0 1 Enable interrupts upon RNFULLF being set #1 TNEARIEN Transmit FIFO nearly empty interrupt enable 2 1 read-write 0 No interrupt upon TNEAREF being set #0 1 Enable interrupts upon TNEAREF being set #1 INTCLR Interrupt clearing mechanism select 3 1 read-write 0 These interrupts are cleared when the corresponding flags are cleared depending on the state of the FIFOs #0 1 These interrupts are cleared by writing the corresponding bits in the CI register #1 RNFULLF_MARK Receive FIFO nearly full watermark 4 1 read-write 0 RNFULLF is set when the receive FIFO has 48 bits or more #0 1 RNFULLF is set when the receive FIFO has 32 bits or more #1 TNEAREF_MARK Transmit FIFO nearly empty watermark 5 1 read-write 0 TNEAREF is set when the transmit FIFO has 16 bits or less #0 1 TNEAREF is set when the transmit FIFO has 32 bits or less #1 LLWU Low leakage wakeup unit LLWU_ 0x4007C000 0 0xA registers LLWU 7 PE1 LLWU Pin Enable 1 register 0 8 read-write 0 0xFF WUPE0 Wakeup Pin Enable For LLWU_P0 0 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE1 Wakeup Pin Enable For LLWU_P1 2 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE2 Wakeup Pin Enable For LLWU_P2 4 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE3 Wakeup Pin Enable For LLWU_P3 6 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 PE2 LLWU Pin Enable 2 register 0x1 8 read-write 0 0xFF WUPE4 Wakeup Pin Enable For LLWU_P4 0 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE5 Wakeup Pin Enable For LLWU_P5 2 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE6 Wakeup Pin Enable For LLWU_P6 4 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE7 Wakeup Pin Enable For LLWU_P7 6 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 PE3 LLWU Pin Enable 3 register 0x2 8 read-write 0 0xFF WUPE8 Wakeup Pin Enable For LLWU_P8 0 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE9 Wakeup Pin Enable For LLWU_P9 2 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE10 Wakeup Pin Enable For LLWU_P10 4 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE11 Wakeup Pin Enable For LLWU_P11 6 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 PE4 LLWU Pin Enable 4 register 0x3 8 read-write 0 0xFF WUPE12 Wakeup Pin Enable For LLWU_P12 0 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE13 Wakeup Pin Enable For LLWU_P13 2 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE14 Wakeup Pin Enable For LLWU_P14 4 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE15 Wakeup Pin Enable For LLWU_P15 6 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 ME LLWU Module Enable register 0x4 8 read-write 0 0xFF WUME0 Wakeup Module Enable For Module 0 0 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 WUME1 Wakeup Module Enable for Module 1 1 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 WUME2 Wakeup Module Enable For Module 2 2 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 WUME3 Wakeup Module Enable For Module 3 3 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 WUME4 Wakeup Module Enable For Module 4 4 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 WUME5 Wakeup Module Enable For Module 5 5 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 WUME6 Wakeup Module Enable For Module 6 6 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 WUME7 Wakeup Module Enable For Module 7 7 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 F1 LLWU Flag 1 register 0x5 8 read-write 0 0xFF WUF0 Wakeup Flag For LLWU_P0 0 1 read-write 0 LLWU_P0 input was not a wakeup source #0 1 LLWU_P0 input was a wakeup source #1 WUF1 Wakeup Flag For LLWU_P1 1 1 read-write 0 LLWU_P1 input was not a wakeup source #0 1 LLWU_P1 input was a wakeup source #1 WUF2 Wakeup Flag For LLWU_P2 2 1 read-write 0 LLWU_P2 input was not a wakeup source #0 1 LLWU_P2 input was a wakeup source #1 WUF3 Wakeup Flag For LLWU_P3 3 1 read-write 0 LLWU_P3 input was not a wake-up source #0 1 LLWU_P3 input was a wake-up source #1 WUF4 Wakeup Flag For LLWU_P4 4 1 read-write 0 LLWU_P4 input was not a wakeup source #0 1 LLWU_P4 input was a wakeup source #1 WUF5 Wakeup Flag For LLWU_P5 5 1 read-write 0 LLWU_P5 input was not a wakeup source #0 1 LLWU_P5 input was a wakeup source #1 WUF6 Wakeup Flag For LLWU_P6 6 1 read-write 0 LLWU_P6 input was not a wakeup source #0 1 LLWU_P6 input was a wakeup source #1 WUF7 Wakeup Flag For LLWU_P7 7 1 read-write 0 LLWU_P7 input was not a wakeup source #0 1 LLWU_P7 input was a wakeup source #1 F2 LLWU Flag 2 register 0x6 8 read-write 0 0xFF WUF8 Wakeup Flag For LLWU_P8 0 1 read-write 0 LLWU_P8 input was not a wakeup source #0 1 LLWU_P8 input was a wakeup source #1 WUF9 Wakeup Flag For LLWU_P9 1 1 read-write 0 LLWU_P9 input was not a wakeup source #0 1 LLWU_P9 input was a wakeup source #1 WUF10 Wakeup Flag For LLWU_P10 2 1 read-write 0 LLWU_P10 input was not a wakeup source #0 1 LLWU_P10 input was a wakeup source #1 WUF11 Wakeup Flag For LLWU_P11 3 1 read-write 0 LLWU_P11 input was not a wakeup source #0 1 LLWU_P11 input was a wakeup source #1 WUF12 Wakeup Flag For LLWU_P12 4 1 read-write 0 LLWU_P12 input was not a wakeup source #0 1 LLWU_P12 input was a wakeup source #1 WUF13 Wakeup Flag For LLWU_P13 5 1 read-write 0 LLWU_P13 input was not a wakeup source #0 1 LLWU_P13 input was a wakeup source #1 WUF14 Wakeup Flag For LLWU_P14 6 1 read-write 0 LLWU_P14 input was not a wakeup source #0 1 LLWU_P14 input was a wakeup source #1 WUF15 Wakeup Flag For LLWU_P15 7 1 read-write 0 LLWU_P15 input was not a wakeup source #0 1 LLWU_P15 input was a wakeup source #1 F3 LLWU Flag 3 register 0x7 8 read-only 0 0xFF MWUF0 Wakeup flag For module 0 0 1 read-only 0 Module 0 input was not a wakeup source #0 1 Module 0 input was a wakeup source #1 MWUF1 Wakeup flag For module 1 1 1 read-only 0 Module 1 input was not a wakeup source #0 1 Module 1 input was a wakeup source #1 MWUF2 Wakeup flag For module 2 2 1 read-only 0 Module 2 input was not a wakeup source #0 1 Module 2 input was a wakeup source #1 MWUF3 Wakeup flag For module 3 3 1 read-only 0 Module 3 input was not a wakeup source #0 1 Module 3 input was a wakeup source #1 MWUF4 Wakeup flag For module 4 4 1 read-only 0 Module 4 input was not a wakeup source #0 1 Module 4 input was a wakeup source #1 MWUF5 Wakeup flag For module 5 5 1 read-only 0 Module 5 input was not a wakeup source #0 1 Module 5 input was a wakeup source #1 MWUF6 Wakeup flag For module 6 6 1 read-only 0 Module 6 input was not a wakeup source #0 1 Module 6 input was a wakeup source #1 MWUF7 Wakeup flag For module 7 7 1 read-only 0 Module 7 input was not a wakeup source #0 1 Module 7 input was a wakeup source #1 FILT1 LLWU Pin Filter 1 register 0x8 8 read-write 0 0xFF FILTSEL Filter Pin Select 0 4 read-write 0000 Select LLWU_P0 for filter #0000 1111 Select LLWU_P15 for filter #1111 FILTE Digital Filter On External Pin 5 2 read-write 00 Filter disabled #00 01 Filter posedge detect enabled #01 10 Filter negedge detect enabled #10 11 Filter any edge detect enabled #11 FILTF Filter Detect Flag 7 1 read-write 0 Pin Filter 1 was not a wakeup source #0 1 Pin Filter 1 was a wakeup source #1 FILT2 LLWU Pin Filter 2 register 0x9 8 read-write 0 0xFF FILTSEL Filter Pin Select 0 4 read-write 0000 Select LLWU_P0 for filter #0000 1111 Select LLWU_P15 for filter #1111 FILTE Digital Filter On External Pin 5 2 read-write 00 Filter disabled #00 01 Filter posedge detect enabled #01 10 Filter negedge detect enabled #10 11 Filter any edge detect enabled #11 FILTF Filter Detect Flag 7 1 read-write 0 Pin Filter 2 was not a wakeup source #0 1 Pin Filter 2 was a wakeup source #1 PMC Power Management Controller PMC_ 0x4007D000 0 0x3 registers LVD_LVW 6 LVDSC1 Low Voltage Detect Status And Control 1 register 0 8 read-write 0x10 0xFF LVDV Low-Voltage Detect Voltage Select 0 2 read-write 00 Low trip point selected (V LVD = V LVDL ) #00 01 High trip point selected (V LVD = V LVDH ) #01 LVDRE Low-Voltage Detect Reset Enable 4 1 read-write 0 LVDF does not generate hardware resets #0 1 Force an MCU reset when LVDF = 1 #1 LVDIE Low-Voltage Detect Interrupt Enable 5 1 read-write 0 Hardware interrupt disabled (use polling) #0 1 Request a hardware interrupt when LVDF = 1 #1 LVDACK Low-Voltage Detect Acknowledge 6 1 write-only LVDF Low-Voltage Detect Flag 7 1 read-only 0 Low-voltage event not detected #0 1 Low-voltage event detected #1 LVDSC2 Low Voltage Detect Status And Control 2 register 0x1 8 read-write 0 0xFF LVWV Low-Voltage Warning Voltage Select 0 2 read-write 00 Low trip point selected (VLVW = VLVW1) #00 01 Mid 1 trip point selected (VLVW = VLVW2) #01 10 Mid 2 trip point selected (VLVW = VLVW3) #10 11 High trip point selected (VLVW = VLVW4) #11 LVWIE Low-Voltage Warning Interrupt Enable 5 1 read-write 0 Hardware interrupt disabled (use polling) #0 1 Request a hardware interrupt when LVWF = 1 #1 LVWACK Low-Voltage Warning Acknowledge 6 1 write-only LVWF Low-Voltage Warning Flag 7 1 read-only 0 Low-voltage warning event not detected #0 1 Low-voltage warning event detected #1 REGSC Regulator Status And Control register 0x2 8 read-write 0x4 0xFF BGBE Bandgap Buffer Enable 0 1 read-write 0 Bandgap buffer not enabled #0 1 Bandgap buffer enabled #1 REGONS Regulator In Run Regulation Status 2 1 read-only 0 Regulator is in stop regulation or in transition to/from it #0 1 Regulator is in run regulation #1 ACKISO Acknowledge Isolation 3 1 read-write 0 Peripherals and I/O pads are in normal run state. #0 1 Certain peripherals and I/O pads are in an isolated and latched state. #1 BGEN Bandgap Enable In VLPx Operation 4 1 read-write 0 Bandgap voltage reference is disabled in VLPx , LLS , and VLLSx modes. #0 1 Bandgap voltage reference is enabled in VLPx , LLS , and VLLSx modes. #1 SMC System Mode Controller SMC_ 0x4007E000 0 0x4 registers PMPROT Power Mode Protection register 0 8 read-write 0 0xFF AVLLS Allow Very-Low-Leakage Stop Mode 1 1 read-write 0 Any VLLSx mode is not allowed #0 1 Any VLLSx mode is allowed #1 ALLS Allow Low-Leakage Stop Mode 3 1 read-write 0 LLS is not allowed #0 1 LLS is allowed #1 AVLP Allow Very-Low-Power Modes 5 1 read-write 0 VLPR, VLPW, and VLPS are not allowed. #0 1 VLPR, VLPW, and VLPS are allowed. #1 PMCTRL Power Mode Control register 0x1 8 read-write 0 0xFF STOPM Stop Mode Control 0 3 read-write 000 Normal Stop (STOP) #000 010 Very-Low-Power Stop (VLPS) #010 011 Low-Leakage Stop (LLS) #011 100 Very-Low-Leakage Stop (VLLSx) #100 110 Reseved #110 STOPA Stop Aborted 3 1 read-only 0 The previous stop mode entry was successsful. #0 1 The previous stop mode entry was aborted. #1 RUNM Run Mode Control 5 2 read-write 00 Normal Run mode (RUN) #00 10 Very-Low-Power Run mode (VLPR) #10 STOPCTRL Stop Control Register 0x2 8 read-write 0x3 0xFF VLLSM VLLS Mode Control 0 3 read-write 000 VLLS0 #000 001 VLLS1 #001 011 VLLS3 #011 PORPO POR Power Option 5 1 read-write 0 POR detect circuit is enabled in VLLS0 #0 1 POR detect circuit is disabled in VLLS0 #1 PSTOPO Partial Stop Option 6 2 read-write 00 STOP - Normal Stop mode #00 01 PSTOP1 - Partial Stop with both system and bus clocks disabled #01 10 PSTOP2 - Partial Stop with system clock disabled and bus clock enabled #10 PMSTAT Power Mode Status register 0x3 8 read-only 0x1 0xFF PMSTAT When debug is enabled, the PMSTAT will not update to STOP or VLPS When a PSTOP mode is enabled, the PMSTAT will not update to STOP or VLPS 0 7 read-only RCM Reset Control Module RCM_ 0x4007F000 0 0x6 registers SRS0 System Reset Status Register 0 0 8 read-only 0x82 0xFF WAKEUP Low Leakage Wakeup Reset 0 1 read-only 0 Reset not caused by LLWU module wakeup source #0 1 Reset caused by LLWU module wakeup source #1 LVD Low-Voltage Detect Reset 1 1 read-only 0 Reset not caused by LVD trip or POR #0 1 Reset caused by LVD trip or POR #1 LOC Loss-of-Clock Reset 2 1 read-only 0 Reset not caused by a loss of external clock. #0 1 Reset caused by a loss of external clock. #1 LOL Loss-of-Lock Reset 3 1 read-only 0 Reset not caused by a loss of lock in the PLL #0 1 Reset caused by a loss of lock in the PLL #1 WDOG Watchdog 5 1 read-only 0 Reset not caused by watchdog timeout #0 1 Reset caused by watchdog timeout #1 PIN External Reset Pin 6 1 read-only 0 Reset not caused by external reset pin #0 1 Reset caused by external reset pin #1 POR Power-On Reset 7 1 read-only 0 Reset not caused by POR #0 1 Reset caused by POR #1 SRS1 System Reset Status Register 1 0x1 8 read-only 0 0xFF LOCKUP Core Lockup 1 1 read-only 0 Reset not caused by core LOCKUP event #0 1 Reset caused by core LOCKUP event #1 SW Software 2 1 read-only 0 Reset not caused by software setting of SYSRESETREQ bit #0 1 Reset caused by software setting of SYSRESETREQ bit #1 MDM_AP MDM-AP System Reset Request 3 1 read-only 0 Reset not caused by host debugger system setting of the System Reset Request bit #0 1 Reset caused by host debugger system setting of the System Reset Request bit #1 SACKERR Stop Mode Acknowledge Error Reset 5 1 read-only 0 Reset not caused by peripheral failure to acknowledge attempt to enter stop mode #0 1 Reset caused by peripheral failure to acknowledge attempt to enter stop mode #1 RPFC Reset Pin Filter Control register 0x4 8 read-write 0 0xFF RSTFLTSRW Reset Pin Filter Select in Run and Wait Modes 0 2 read-write 00 All filtering disabled #00 01 Bus clock filter enabled for normal operation #01 10 LPO clock filter enabled for normal operation #10 RSTFLTSS Reset Pin Filter Select in Stop Mode 2 1 read-write 0 All filtering disabled #0 1 LPO clock filter enabled #1 RPFW Reset Pin Filter Width register 0x5 8 read-write 0 0xFF RSTFLTSEL Reset Pin Filter Bus Clock Select 0 5 read-write 00000 Bus clock filter count is 1 #00000 00001 Bus clock filter count is 2 #00001 00010 Bus clock filter count is 3 #00010 00011 Bus clock filter count is 4 #00011 00100 Bus clock filter count is 5 #00100 00101 Bus clock filter count is 6 #00101 00110 Bus clock filter count is 7 #00110 00111 Bus clock filter count is 8 #00111 01000 Bus clock filter count is 9 #01000 01001 Bus clock filter count is 10 #01001 01010 Bus clock filter count is 11 #01010 01011 Bus clock filter count is 12 #01011 01100 Bus clock filter count is 13 #01100 01101 Bus clock filter count is 14 #01101 01110 Bus clock filter count is 15 #01110 01111 Bus clock filter count is 16 #01111 10000 Bus clock filter count is 17 #10000 10001 Bus clock filter count is 18 #10001 10010 Bus clock filter count is 19 #10010 10011 Bus clock filter count is 20 #10011 10100 Bus clock filter count is 21 #10100 10101 Bus clock filter count is 22 #10101 10110 Bus clock filter count is 23 #10110 10111 Bus clock filter count is 24 #10111 11000 Bus clock filter count is 25 #11000 11001 Bus clock filter count is 26 #11001 11010 Bus clock filter count is 27 #11010 11011 Bus clock filter count is 28 #11011 11100 Bus clock filter count is 29 #11100 11101 Bus clock filter count is 30 #11101 11110 Bus clock filter count is 31 #11110 11111 Bus clock filter count is 32 #11111 GPIOA General Purpose Input/Output GPIO GPIOA_ 0x400FF000 0 0x18 registers PORTA 30 PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 GPIOB General Purpose Input/Output GPIO GPIOB_ 0x400FF040 0 0x18 registers PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 GPIOC General Purpose Input/Output GPIO GPIOC_ 0x400FF080 0 0x18 registers PORTC_PORTD 31 PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 GPIOD General Purpose Input/Output GPIO GPIOD_ 0x400FF0C0 0 0x18 registers PORTC_PORTD 31 PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 GPIOE General Purpose Input/Output GPIO GPIOE_ 0x400FF100 0 0x18 registers PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 MTB Micro Trace Buffer MTB_ 0xF0000000 0 0x1000 registers POSITION MTB Position Register 0 32 read-write 0 0x3 WRAP This field is set to 1 automatically when the POINTER value wraps as determined by the MTB_MASTER[MASK] field in the MASTER Trace Control Register 2 1 read-write POINTER Trace Packet Address Pointer[28:0] 3 29 read-write MASTER MTB Master Register 0x4 32 read-write 0x80 0xFFFFFFE0 MASK Mask 0 5 read-write TSTARTEN Trace Start Input Enable 5 1 read-write TSTOPEN Trace Stop Input Enable 6 1 read-write SFRWPRIV Special Function Register Write Privilege 7 1 read-write RAMPRIV RAM Privilege 8 1 read-write HALTREQ Halt Request 9 1 read-write EN Main Trace Enable 31 1 read-write FLOW MTB Flow Register 0x8 32 read-write 0 0x4 AUTOSTOP If this field is 1 and WATERMARK is equal to MTB_POSITION[POINTER], then MTB_MASTER[EN] is automatically set to 0 0 1 read-write AUTOHALT If this field is 1 and WATERMARK is equal to MTB_POSITION[POINTER], then MTB_MASTER[HALTREQ] is automatically set to 1 1 1 read-write WATERMARK WATERMARK[28:0] 3 29 read-write BASE MTB Base Register 0xC 32 read-only 0 0 BASEADDR This value is defined with a hardwired signal and the expression: 0x2000_0000 - (RAM_Size/4) 0 32 read-only MODECTRL Integration Mode Control Register 0xF00 32 read-only 0 0xFFFFFFFF MODECTRL Hardwired to 0x0000_0000 0 32 read-only TAGSET Claim TAG Set Register 0xFA0 32 read-only 0 0xFFFFFFFF TAGSET Hardwired to 0x0000_0000 0 32 read-only TAGCLEAR Claim TAG Clear Register 0xFA4 32 read-only 0 0xFFFFFFFF TAGCLEAR Hardwired to 0x0000_0000 0 32 read-only LOCKACCESS Lock Access Register 0xFB0 32 read-only 0 0xFFFFFFFF LOCKACCESS Hardwired to 0x0000_0000 0 32 read-only LOCKSTAT Lock Status Register 0xFB4 32 read-only 0 0xFFFFFFFF LOCKSTAT Hardwired to 0x0000_0000 0 32 read-only AUTHSTAT Authentication Status Register 0xFB8 32 read-only 0 0xFFFFFFFF BIT0 Connected to DBGEN. 0 1 read-only BIT1 Hardwired to 1. 1 1 read-only BIT2 Connected to NIDEN or DBGEN signal. 2 1 read-only BIT3 Hardwired to 1. 3 1 read-only DEVICEARCH Device Architecture Register 0xFBC 32 read-only 0x47700A31 0xFFFFFFFF DEVICEARCH Hardwired to 0x4770_0A31. 0 32 read-only DEVICECFG Device Configuration Register 0xFC8 32 read-only 0 0xFFFFFFFF DEVICECFG Hardwired to 0x0000_0000. 0 32 read-only DEVICETYPID Device Type Identifier Register 0xFCC 32 read-only 0x31 0xFFFFFFFF DEVICETYPID Hardwired to 0x0000_0031. 0 32 read-only 8 0x4 4,5,6,7,0,1,2,3 PERIPHID%s Peripheral ID Register 0xFD0 32 read-only 0 0 PERIPHID Peripheral ID4 is hardwired to 0x0000_0004; ID0 to 0x0000_0032; ID1 to 0x0000_00B9; ID2 to 0x0000_000B; and all the others to 0x0000_0000 0 32 read-only 4 0x4 0,1,2,3 COMPID%s Component ID Register 0xFF0 32 read-only 0 0 COMPID Component ID 0 32 read-only MTBDWT MTB data watchpoint and trace MTBDWT_ 0xF0001000 0 0x1000 registers CTRL MTB DWT Control Register 0 32 read-only 0x2F000000 0xFFFFFFFF DWTCFGCTRL DWT configuration controls 0 28 read-only NUMCMP Number of comparators 28 4 read-only 2 0x10 0,1 COMP%s MTB_DWT Comparator Register 0x20 32 read-write 0 0xFFFFFFFF COMP Reference value for comparison 0 32 read-write 2 0x10 0,1 MASK%s MTB_DWT Comparator Mask Register 0x24 32 read-write 0 0xFFFFFFFF MASK MASK 0 5 read-write FCT0 MTB_DWT Comparator Function Register 0 0x28 32 read-write 0 0xFFFFFFFF FUNCTION Function 0 4 read-write 0000 Disabled. #0000 0100 Instruction fetch. #0100 0101 Data operand read. #0101 0110 Data operand write. #0110 0111 Data operand (read + write). #0111 DATAVMATCH Data Value Match 8 1 read-write 0 Perform address comparison. #0 1 Perform data value comparison. #1 DATAVSIZE Data Value Size 10 2 read-write 00 Byte. #00 01 Halfword. #01 10 Word. #10 11 Reserved. Any attempts to use this value results in UNPREDICTABLE behavior. #11 DATAVADDR0 Data Value Address 0 12 4 read-write MATCHED Comparator match 24 1 read-only 0 No match. #0 1 Match occurred. #1 FCT1 MTB_DWT Comparator Function Register 1 0x38 32 read-write 0 0xFFFFFFFF FUNCTION Function 0 4 read-write 0000 Disabled. #0000 0100 Instruction fetch. #0100 0101 Data operand read. #0101 0110 Data operand write. #0110 0111 Data operand (read + write). #0111 MATCHED Comparator match 24 1 read-only 0 No match. #0 1 Match occurred. #1 TBCTRL MTB_DWT Trace Buffer Control Register 0x200 32 read-write 0x20000000 0xFFFFFFFF ACOMP0 Action based on Comparator 0 match 0 1 read-write 0 Trigger TSTOP based on the assertion of MTBDWT_FCT0[MATCHED]. #0 1 Trigger TSTART based on the assertion of MTBDWT_FCT0[MATCHED]. #1 ACOMP1 Action based on Comparator 1 match 1 1 read-write 0 Trigger TSTOP based on the assertion of MTBDWT_FCT1[MATCHED]. #0 1 Trigger TSTART based on the assertion of MTBDWT_FCT1[MATCHED]. #1 NUMCOMP Number of Comparators 28 4 read-only DEVICECFG Device Configuration Register 0xFC8 32 read-only 0 0xFFFFFFFF DEVICECFG Hardwired to 0x0000_0000. 0 32 read-only DEVICETYPID Device Type Identifier Register 0xFCC 32 read-only 0x4 0xFFFFFFFF DEVICETYPID Hardwired to 0x0000_0004. 0 32 read-only 8 0x4 4,5,6,7,0,1,2,3 PERIPHID%s Peripheral ID Register 0xFD0 32 read-only 0 0 PERIPHID Peripheral ID1 is hardwired to 0x0000_00E0; ID2 to 0x0000_0008; and all the others to 0x0000_0000. 0 32 read-only 4 0x4 0,1,2,3 COMPID%s Component ID Register 0xFF0 32 read-only 0 0 COMPID Component ID 0 32 read-only ROM System ROM ROM_ 0xF0002000 0 0x1000 registers 3 0x4 0,1,2 ENTRY%s Entry 0 32 read-only 0 0 ENTRY ENTRY 0 32 read-only TABLEMARK End of Table Marker Register 0xC 32 read-only 0 0xFFFFFFFF MARK Hardwired to 0x0000_0000 0 32 read-only SYSACCESS System Access Register 0xFCC 32 read-only 0x1 0xFFFFFFFF SYSACCESS Hardwired to 0x0000_0001 0 32 read-only 8 0x4 4,5,6,7,0,1,2,3 PERIPHID%s Peripheral ID Register 0xFD0 32 read-only 0 0 PERIPHID Peripheral ID1 is hardwired to 0x0000_00E0; ID2 to 0x0000_0008; and all the others to 0x0000_0000. 0 32 read-only 4 0x4 0,1,2,3 COMPID%s Component ID Register 0xFF0 32 read-only 0 0 COMPID Component ID 0 32 read-only MCM Core Platform Miscellaneous Control Module MCM_ 0xF0003000 0x8 0x3C registers PLASC Crossbar Switch (AXBS) Slave Configuration 0x8 16 read-only 0x7 0xFFFF ASC Each bit in the ASC field indicates whether there is a corresponding connection to the crossbar switch's slave input port. 0 8 read-only 0 A bus slave connection to AXBS input port n is absent. #0 1 A bus slave connection to AXBS input port n is present. #1 PLAMC Crossbar Switch (AXBS) Master Configuration 0xA 16 read-only 0xD 0xFFFF AMC Each bit in the AMC field indicates whether there is a corresponding connection to the AXBS master input port. 0 8 read-only 0 A bus master connection to AXBS input port n is absent #0 1 A bus master connection to AXBS input port n is present #1 PLACR Platform Control Register 0xC 32 read-write 0 0xFFFFFFFF ARB Arbitration select 9 1 read-write 0 Fixed-priority arbitration for the crossbar masters #0 1 Round-robin arbitration for the crossbar masters #1 CFCC Clear Flash Controller Cache 10 1 write-only DFCDA Disable Flash Controller Data Caching 11 1 read-write 0 Enable flash controller data caching #0 1 Disable flash controller data caching. #1 DFCIC Disable Flash Controller Instruction Caching 12 1 read-write 0 Enable flash controller instruction caching. #0 1 Disable flash controller instruction caching. #1 DFCC Disable Flash Controller Cache 13 1 read-write 0 Enable flash controller cache. #0 1 Disable flash controller cache. #1 EFDS Enable Flash Data Speculation 14 1 read-write 0 Disable flash data speculation. #0 1 Enable flash data speculation. #1 DFCS Disable Flash Controller Speculation 15 1 read-write 0 Enable flash controller speculation. #0 1 Disable flash controller speculation. #1 ESFC Enable Stalling Flash Controller 16 1 read-write 0 Disable stalling flash controller when flash is busy. #0 1 Enable stalling flash controller when flash is busy. #1 CPO Compute Operation Control Register 0x40 32 read-write 0 0xFFFFFFFF CPOREQ Compute Operation Request 0 1 read-write 0 Request is cleared. #0 1 Request Compute Operation. #1 CPOACK Compute Operation Acknowledge 1 1 read-only 0 Compute operation entry has not completed or compute operation exit has completed. #0 1 Compute operation entry has completed or compute operation exit has not completed. #1 CPOWOI Compute Operation Wake-up on Interrupt 2 1 read-write 0 No effect. #0 1 When set, the CPOREQ is cleared on any interrupt or exception vector fetch. #1 FGPIOA General Purpose Input/Output FGPIO FGPIOA_ 0xF8000000 0 0x18 registers PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 FGPIOB General Purpose Input/Output FGPIO FGPIOB_ 0xF8000040 0 0x18 registers PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 FGPIOC General Purpose Input/Output FGPIO FGPIOC_ 0xF8000080 0 0x18 registers PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 FGPIOD General Purpose Input/Output FGPIO FGPIOD_ 0xF80000C0 0 0x18 registers PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 FGPIOE General Purpose Input/Output FGPIO FGPIOE_ 0xF8000100 0 0x18 registers PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1