Freescale Semiconductor, Inc. Freescale Kinetis_E MKE14Z7 1.6 MKE14Z7 Freescale Microcontroller Redistribution and use in source and binary forms, with or without modification,\nare permitted provided that the following conditions are met:\n o Redistributions of source code must retain the above copyright notice, this list\n of conditions and the following disclaimer.\n o Redistributions in binary form must reproduce the above copyright notice, this\n list of conditions and the following disclaimer in the documentation and/or\n other materials provided with the distribution.\n o Neither the name of Freescale Semiconductor, Inc. nor the names of its\n contributors may be used to endorse or promote products derived from this\n software without specific prior written permission.\n THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND\n ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED\n WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE\n DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR\n ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES\n (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;\n LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON\n ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT\n (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS\n SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. CM0PLUS r0p0 little false false true 2 false 8 32 FTFE_FlashConfig Flash configuration field NV_ 0x400 0 0x10 registers BACKKEY3 Backdoor Comparison Key 3. 0 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only BACKKEY2 Backdoor Comparison Key 2. 0x1 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only BACKKEY1 Backdoor Comparison Key 1. 0x2 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only BACKKEY0 Backdoor Comparison Key 0. 0x3 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only BACKKEY7 Backdoor Comparison Key 7. 0x4 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only BACKKEY6 Backdoor Comparison Key 6. 0x5 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only BACKKEY5 Backdoor Comparison Key 5. 0x6 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only BACKKEY4 Backdoor Comparison Key 4. 0x7 8 read-only 0xFF 0xFF KEY Backdoor Comparison Key. 0 8 read-only FPROT3 Non-volatile P-Flash Protection 1 - Low Register 0x8 8 read-only 0xFF 0xFF PROT P-Flash Region Protect 0 8 read-only FPROT2 Non-volatile P-Flash Protection 1 - High Register 0x9 8 read-only 0xFF 0xFF PROT P-Flash Region Protect 0 8 read-only FPROT1 Non-volatile P-Flash Protection 0 - Low Register 0xA 8 read-only 0xFF 0xFF PROT P-Flash Region Protect 0 8 read-only FPROT0 Non-volatile P-Flash Protection 0 - High Register 0xB 8 read-only 0xFF 0xFF PROT P-Flash Region Protect 0 8 read-only FSEC Non-volatile Flash Security Register 0xC 8 read-only 0xFF 0xFF SEC Flash Security 0 2 read-only 10 MCU security status is unsecure #10 11 MCU security status is secure #11 FSLACC Freescale Failure Analysis Access Code 2 2 read-only 10 Freescale factory access denied #10 11 Freescale factory access granted #11 MEEN no description available 4 2 read-only 10 Mass erase is disabled #10 11 Mass erase is enabled #11 KEYEN Backdoor Key Security Enable 6 2 read-only 10 Backdoor key access enabled #10 11 Backdoor key access disabled #11 FOPT Non-volatile Flash Option Register 0xD 8 read-only 0x7D 0xFF LPBOOT no description available 0 1 read-only 00 Low-power boot #0 01 Normal boot #1 BOOTPIN_OPT no description available 1 1 read-only 00 Force Boot from ROM if BOOTCFG0 asserted, where BOOTCFG0 is the boot config function which is muxed with NMI pin #0 01 Boot source configured by FOPT (BOOTSRC_SEL) bits #1 NMI_DIS no description available 2 1 read-only 00 NMI interrupts are always blocked #0 01 NMI_b pin/interrupts reset default to enabled #1 FAST_INIT no description available 5 1 read-only 00 Slower initialization #0 01 Fast Initialization #1 BOOTSRC_SEL Boot source selection 6 2 read-only 00 Boot from Flash #00 10 Boot from ROM #10 11 Boot from ROM #11 FEPROT Non-volatile EERAM Protection Register 0xE 8 read-only 0xFF 0xFF EPROT no description available 0 8 read-only FDPROT Non-volatile D-Flash Protection Register 0xF 8 read-only 0xFF 0xFF DPROT D-Flash Region Protect 0 8 read-only AIPS AIPS-Lite Bridge AIPS_ 0x40000000 0 0x84 registers MPRA Master Privilege Register A 0 32 read-write 0 0xFFFFFFFF MPL2 Master 2 Privilege Level 20 1 read-write 0 Accesses from this master are forced to user-mode. #0 1 Accesses from this master are not forced to user-mode. #1 MTW2 Master 2 Trusted For Writes 21 1 read-write 0 This master is not trusted for write accesses. #0 1 This master is trusted for write accesses. #1 MTR2 Master 2 Trusted For Read 22 1 read-write 0 This master is not trusted for read accesses. #0 1 This master is trusted for read accesses. #1 MPL0 Master 0 Privilege Level 28 1 read-write 0 Accesses from this master are forced to user-mode. #0 1 Accesses from this master are not forced to user-mode. #1 MTW0 Master 0 Trusted For Writes 29 1 read-write 0 This master is not trusted for write accesses. #0 1 This master is trusted for write accesses. #1 MTR0 Master 0 Trusted For Read 30 1 read-write 0 This master is not trusted for read accesses. #0 1 This master is trusted for read accesses. #1 4 0x4 A,B,C,D PACR%s Peripheral Access Control Register 0x20 32 read-write 0 0xFFFFFFFF TP7 Trusted Protect 0 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP7 Write Protect 1 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP7 Supervisor Protect 2 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP6 Trusted Protect 4 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP6 Write Protect 5 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP6 Supervisor Protect 6 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP5 Trusted Protect 8 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP5 Write Protect 9 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP5 Supervisor Protect 10 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP4 Trusted Protect 12 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP4 Write Protect 13 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP4 Supervisor Protect 14 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP3 Trusted Protect 16 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP3 Write Protect 17 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP3 Supervisor Protect 18 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP2 Trusted Protect 20 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP2 Write Protect 21 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP2 Supervisor Protect 22 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP1 Trusted Protect 24 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP1 Write Protect 25 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP1 Supervisor Protect 26 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP0 Trusted Protect 28 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP0 Write Protect 29 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP0 Supervisor Protect 30 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 16 0x4 A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P OPACR%s Off-Platform Peripheral Access Control Register 0x40 32 read-write 0 0xFFFFFFFF TP7 Trusted Protect 0 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP7 Write Protect 1 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP7 Supervisor Protect 2 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP6 Trusted Protect 4 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP6 Write Protect 5 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP6 Supervisor Protect 6 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP5 Trusted Protect 8 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP5 Write Protect 9 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP5 Supervisor Protect 10 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP4 Trusted Protect 12 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP4 Write Protect 13 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP4 Supervisor Protect 14 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP3 Trusted Protect 16 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP3 Write Protect 17 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP3 Supervisor Protect 18 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP2 Trusted Protect 20 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP2 Write Protect 21 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP2 Supervisor Protect 22 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP1 Trusted Protect 24 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP1 Write Protect 25 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP1 Supervisor Protect 26 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP0 Trusted Protect 28 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP0 Write Protect 29 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP0 Supervisor Protect 30 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 PACRU Peripheral Access Control Register 0x80 32 read-write 0 0xFFFFFFFF TP1 Trusted Protect 24 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP1 Write Protect 25 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP1 Supervisor Protect 26 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 TP0 Trusted Protect 28 1 read-write 0 Accesses from an untrusted master are allowed. #0 1 Accesses from an untrusted master are not allowed. #1 WP0 Write Protect 29 1 read-write 0 This peripheral allows write accesses. #0 1 This peripheral is write protected. #1 SP0 Supervisor Protect 30 1 read-write 0 This peripheral does not require supervisor privilege level for accesses. #0 1 This peripheral requires supervisor privilege level for accesses. #1 DMA Enhanced direct memory access controller DMA_ 0x40008000 0 0x1100 registers DMA0_04 0 DMA0_15 1 DMA0_26 2 DMA0_37 3 DMA_Error 4 CR Control Register 0 32 read-write 0 0xFFFFFFFF EDBG Enable Debug 1 1 read-write 0 When in debug mode, the DMA continues to operate. #0 1 When in debug mode, the DMA stalls the start of a new channel. Executing channels are allowed to complete. Channel execution resumes when the system exits debug mode or the EDBG bit is cleared. #1 ERCA Enable Round Robin Channel Arbitration 2 1 read-write 0 Fixed priority arbitration is used for channel selection . #0 1 Round robin arbitration is used for channel selection . #1 HOE Halt On Error 4 1 read-write 0 Normal operation #0 1 Any error causes the HALT bit to set. Subsequently, all service requests are ignored until the HALT bit is cleared. #1 HALT Halt DMA Operations 5 1 read-write 0 Normal operation #0 1 Stall the start of any new channels. Executing channels are allowed to complete. Channel execution resumes when this bit is cleared. #1 CLM Continuous Link Mode 6 1 read-write 0 A minor loop channel link made to itself goes through channel arbitration before being activated again. #0 1 A minor loop channel link made to itself does not go through channel arbitration before being activated again. Upon minor loop completion, the channel activates again if that channel has a minor loop channel link enabled and the link channel is itself. This effectively applies the minor loop offsets and restarts the next minor loop. #1 EMLM Enable Minor Loop Mapping 7 1 read-write 0 Disabled. TCDn.word2 is defined as a 32-bit NBYTES field. #0 1 Enabled. TCDn.word2 is redefined to include individual enable fields, an offset field, and the NBYTES field. The individual enable fields allow the minor loop offset to be applied to the source address, the destination address, or both. The NBYTES field is reduced when either offset is enabled. #1 ECX Error Cancel Transfer 16 1 read-write 0 Normal operation #0 1 Cancel the remaining data transfer in the same fashion as the CX bit. Stop the executing channel and force the minor loop to finish. The cancel takes effect after the last write of the current read/write sequence. The ECX bit clears itself after the cancel is honored. In addition to cancelling the transfer, ECX treats the cancel as an error condition, thus updating the Error Status register (DMAx_ES) and generating an optional error interrupt. #1 CX Cancel Transfer 17 1 read-write 0 Normal operation #0 1 Cancel the remaining data transfer. Stop the executing channel and force the minor loop to finish. The cancel takes effect after the last write of the current read/write sequence. The CX bit clears itself after the cancel has been honored. This cancel retires the channel normally as if the minor loop was completed. #1 ACTIVE DMA Active Status 31 1 read-only 0 eDMA is idle. #0 1 eDMA is executing a channel. #1 ES Error Status Register 0x4 32 read-only 0 0xFFFFFFFF DBE Destination Bus Error 0 1 read-only 0 No destination bus error #0 1 The last recorded error was a bus error on a destination write #1 SBE Source Bus Error 1 1 read-only 0 No source bus error #0 1 The last recorded error was a bus error on a source read #1 SGE Scatter/Gather Configuration Error 2 1 read-only 0 No scatter/gather configuration error #0 1 The last recorded error was a configuration error detected in the TCDn_DLASTSGA field. This field is checked at the beginning of a scatter/gather operation after major loop completion if TCDn_CSR[ESG] is enabled. TCDn_DLASTSGA is not on a 32 byte boundary. #1 NCE NBYTES/CITER Configuration Error 3 1 read-only 0 No NBYTES/CITER configuration error #0 1 The last recorded error was a configuration error detected in the TCDn_NBYTES or TCDn_CITER fields. TCDn_NBYTES is not a multiple of TCDn_ATTR[SSIZE] and TCDn_ATTR[DSIZE], or TCDn_CITER[CITER] is equal to zero, or TCDn_CITER[ELINK] is not equal to TCDn_BITER[ELINK] #1 DOE Destination Offset Error 4 1 read-only 0 No destination offset configuration error #0 1 The last recorded error was a configuration error detected in the TCDn_DOFF field. TCDn_DOFF is inconsistent with TCDn_ATTR[DSIZE]. #1 DAE Destination Address Error 5 1 read-only 0 No destination address configuration error #0 1 The last recorded error was a configuration error detected in the TCDn_DADDR field. TCDn_DADDR is inconsistent with TCDn_ATTR[DSIZE]. #1 SOE Source Offset Error 6 1 read-only 0 No source offset configuration error #0 1 The last recorded error was a configuration error detected in the TCDn_SOFF field. TCDn_SOFF is inconsistent with TCDn_ATTR[SSIZE]. #1 SAE Source Address Error 7 1 read-only 0 No source address configuration error. #0 1 The last recorded error was a configuration error detected in the TCDn_SADDR field. TCDn_SADDR is inconsistent with TCDn_ATTR[SSIZE]. #1 ERRCHN Error Channel Number or Canceled Channel Number 8 3 read-only CPE Channel Priority Error 14 1 read-only 0 No channel priority error #0 1 The last recorded error was a configuration error in the channel priorities . Channel priorities are not unique. #1 ECX Transfer Canceled 16 1 read-only 0 No canceled transfers #0 1 The last recorded entry was a canceled transfer by the error cancel transfer input #1 VLD Logical OR of all ERR status bits 31 1 read-only 0 No ERR bits are set. #0 1 At least one ERR bit is set indicating a valid error exists that has not been cleared. #1 ERQ Enable Request Register 0xC 32 read-write 0 0xFFFFFFFF ERQ0 Enable DMA Request 0 0 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ1 Enable DMA Request 1 1 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ2 Enable DMA Request 2 2 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ3 Enable DMA Request 3 3 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ4 Enable DMA Request 4 4 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ5 Enable DMA Request 5 5 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ6 Enable DMA Request 6 6 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ7 Enable DMA Request 7 7 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 EEI Enable Error Interrupt Register 0x14 32 read-write 0 0xFFFFFFFF EEI0 Enable Error Interrupt 0 0 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI1 Enable Error Interrupt 1 1 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI2 Enable Error Interrupt 2 2 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI3 Enable Error Interrupt 3 3 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI4 Enable Error Interrupt 4 4 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI5 Enable Error Interrupt 5 5 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI6 Enable Error Interrupt 6 6 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI7 Enable Error Interrupt 7 7 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 CEEI Clear Enable Error Interrupt Register 0x18 8 write-only 0 0xFF CEEI Clear Enable Error Interrupt 0 3 write-only CAEE Clear All Enable Error Interrupts 6 1 write-only 0 Clear only the EEI bit specified in the CEEI field #0 1 Clear all bits in EEI #1 NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 SEEI Set Enable Error Interrupt Register 0x19 8 write-only 0 0xFF SEEI Set Enable Error Interrupt 0 3 write-only SAEE Sets All Enable Error Interrupts 6 1 write-only 0 Set only the EEI bit specified in the SEEI field. #0 1 Sets all bits in EEI #1 NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 CERQ Clear Enable Request Register 0x1A 8 write-only 0 0xFF CERQ Clear Enable Request 0 3 write-only CAER Clear All Enable Requests 6 1 write-only 0 Clear only the ERQ bit specified in the CERQ field #0 1 Clear all bits in ERQ #1 NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 SERQ Set Enable Request Register 0x1B 8 write-only 0 0xFF SERQ Set Enable Request 0 3 write-only SAER Set All Enable Requests 6 1 write-only 0 Set only the ERQ bit specified in the SERQ field #0 1 Set all bits in ERQ #1 NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 CDNE Clear DONE Status Bit Register 0x1C 8 write-only 0 0xFF CDNE Clear DONE Bit 0 3 write-only CADN Clears All DONE Bits 6 1 write-only 0 Clears only the TCDn_CSR[DONE] bit specified in the CDNE field #0 1 Clears all bits in TCDn_CSR[DONE] #1 NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 SSRT Set START Bit Register 0x1D 8 write-only 0 0xFF SSRT Set START Bit 0 3 write-only SAST Set All START Bits (activates all channels) 6 1 write-only 0 Set only the TCDn_CSR[START] bit specified in the SSRT field #0 1 Set all bits in TCDn_CSR[START] #1 NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 CERR Clear Error Register 0x1E 8 write-only 0 0xFF CERR Clear Error Indicator 0 3 write-only CAEI Clear All Error Indicators 6 1 write-only 0 Clear only the ERR bit specified in the CERR field #0 1 Clear all bits in ERR #1 NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 CINT Clear Interrupt Request Register 0x1F 8 write-only 0 0xFF CINT Clear Interrupt Request 0 3 write-only CAIR Clear All Interrupt Requests 6 1 write-only 0 Clear only the INT bit specified in the CINT field #0 1 Clear all bits in INT #1 NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 INT Interrupt Request Register 0x24 32 read-write 0 0xFFFFFFFF INT0 Interrupt Request 0 0 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT1 Interrupt Request 1 1 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT2 Interrupt Request 2 2 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT3 Interrupt Request 3 3 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT4 Interrupt Request 4 4 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT5 Interrupt Request 5 5 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT6 Interrupt Request 6 6 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT7 Interrupt Request 7 7 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 ERR Error Register 0x2C 32 read-write 0 0xFFFFFFFF ERR0 Error In Channel 0 0 1 read-write 0 An error in this channel has not occurred #0 1 An error in this channel has occurred #1 ERR1 Error In Channel 1 1 1 read-write 0 An error in this channel has not occurred #0 1 An error in this channel has occurred #1 ERR2 Error In Channel 2 2 1 read-write 0 An error in this channel has not occurred #0 1 An error in this channel has occurred #1 ERR3 Error In Channel 3 3 1 read-write 0 An error in this channel has not occurred #0 1 An error in this channel has occurred #1 ERR4 Error In Channel 4 4 1 read-write 0 An error in this channel has not occurred #0 1 An error in this channel has occurred #1 ERR5 Error In Channel 5 5 1 read-write 0 An error in this channel has not occurred #0 1 An error in this channel has occurred #1 ERR6 Error In Channel 6 6 1 read-write 0 An error in this channel has not occurred #0 1 An error in this channel has occurred #1 ERR7 Error In Channel 7 7 1 read-write 0 An error in this channel has not occurred #0 1 An error in this channel has occurred #1 HRS Hardware Request Status Register 0x34 32 read-only 0 0xFFFFFFFF HRS0 Hardware Request Status Channel 0 0 1 read-only 0 A hardware service request for channel 0 is not present #0 1 A hardware service request for channel 0 is present #1 HRS1 Hardware Request Status Channel 1 1 1 read-only 0 A hardware service request for channel 1 is not present #0 1 A hardware service request for channel 1 is present #1 HRS2 Hardware Request Status Channel 2 2 1 read-only 0 A hardware service request for channel 2 is not present #0 1 A hardware service request for channel 2 is present #1 HRS3 Hardware Request Status Channel 3 3 1 read-only 0 A hardware service request for channel 3 is not present #0 1 A hardware service request for channel 3 is present #1 HRS4 Hardware Request Status Channel 4 4 1 read-only 0 A hardware service request for channel 4 is not present #0 1 A hardware service request for channel 4 is present #1 HRS5 Hardware Request Status Channel 5 5 1 read-only 0 A hardware service request for channel 5 is not present #0 1 A hardware service request for channel 5 is present #1 HRS6 Hardware Request Status Channel 6 6 1 read-only 0 A hardware service request for channel 6 is not present #0 1 A hardware service request for channel 6 is present #1 HRS7 Hardware Request Status Channel 7 7 1 read-only 0 A hardware service request for channel 7 is not present #0 1 A hardware service request for channel 7 is present #1 EARS Enable Asynchronous Request in Stop Register 0x44 32 read-write 0 0xFFFFFFFF EDREQ_0 Enable asynchronous DMA request in stop mode for channel 0. 0 1 read-write 0 Disable asynchronous DMA request for channel 0. #0 1 Enable asynchronous DMA request for channel 0. #1 EDREQ_1 Enable asynchronous DMA request in stop mode for channel 1. 1 1 read-write 0 Disable asynchronous DMA request for channel 1 #0 1 Enable asynchronous DMA request for channel 1. #1 EDREQ_2 Enable asynchronous DMA request in stop mode for channel 2. 2 1 read-write 0 Disable asynchronous DMA request for channel 2. #0 1 Enable asynchronous DMA request for channel 2. #1 EDREQ_3 Enable asynchronous DMA request in stop mode for channel 3. 3 1 read-write 0 Disable asynchronous DMA request for channel 3. #0 1 Enable asynchronous DMA request for channel 3. #1 EDREQ_4 Enable asynchronous DMA request in stop mode for channel 4 4 1 read-write 0 Disable asynchronous DMA request for channel 4. #0 1 Enable asynchronous DMA request for channel 4. #1 EDREQ_5 Enable asynchronous DMA request in stop mode for channel 5 5 1 read-write 0 Disable asynchronous DMA request for channel 5. #0 1 Enable asynchronous DMA request for channel 5. #1 EDREQ_6 Enable asynchronous DMA request in stop mode for channel 6 6 1 read-write 0 Disable asynchronous DMA request for channel 6. #0 1 Enable asynchronous DMA request for channel 6. #1 EDREQ_7 Enable asynchronous DMA request in stop mode for channel 7 7 1 read-write 0 Disable asynchronous DMA request for channel 7. #0 1 Enable asynchronous DMA request for channel 7. #1 8 0x1 3,2,1,0,7,6,5,4 DCHPRI%s Channel n Priority Register 0x100 8 read-write 0 0xFF CHPRI Channel n Arbitration Priority 0 3 read-write DPA Disable Preempt Ability. 6 1 read-write 0 Channel n can suspend a lower priority channel. #0 1 Channel n cannot suspend any channel, regardless of channel priority. #1 ECP Enable Channel Preemption. 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request. #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel. #1 8 0x20 0,1,2,3,4,5,6,7 TCD%s_SADDR TCD Source Address 0x1000 32 read-write 0 0 SADDR Source Address 0 32 read-write 8 0x20 0,1,2,3,4,5,6,7 TCD%s_SOFF TCD Signed Source Address Offset 0x1004 16 read-write 0 0 SOFF Source address signed offset 0 16 read-write 8 0x20 0,1,2,3,4,5,6,7 TCD%s_ATTR TCD Transfer Attributes 0x1006 16 read-write 0 0 DSIZE Destination data transfer size 0 3 read-write DMOD Destination Address Modulo 3 5 read-write SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 SMOD Source Address Modulo 11 5 read-write 0 Source address modulo feature is disabled #00000 8 0x20 0,1,2,3,4,5,6,7 TCD%s_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Mapping Disabled) DMA 0x1008 32 read-write 0 0 NBYTES Minor Byte Transfer Count 0 32 read-write 8 0x20 0,1,2,3,4,5,6,7 TCD%s_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Mapping Enabled and Offset Disabled) DMA 0x1008 32 read-write 0 0 NBYTES Minor Byte Transfer Count 0 30 read-write DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 8 0x20 0,1,2,3,4,5,6,7 TCD%s_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop Mapping and Offset Enabled) DMA 0x1008 32 read-write 0 0 NBYTES Minor Byte Transfer Count 0 10 read-write MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 8 0x20 0,1,2,3,4,5,6,7 TCD%s_SLAST TCD Last Source Address Adjustment 0x100C 32 read-write 0 0 SLAST Last Source Address Adjustment 0 32 read-write 8 0x20 0,1,2,3,4,5,6,7 TCD%s_DADDR TCD Destination Address 0x1010 32 read-write 0 0 DADDR Destination Address 0 32 read-write 8 0x20 0,1,2,3,4,5,6,7 TCD%s_DOFF TCD Signed Destination Address Offset 0x1014 16 read-write 0 0 DOFF Destination Address Signed Offset 0 16 read-write 8 0x20 0,1,2,3,4,5,6,7 TCD%s_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x1016 16 read-write 0 0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 8 0x20 0,1,2,3,4,5,6,7 TCD%s_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x1016 16 read-write 0 0 CITER Current Major Iteration Count 0 9 read-write LINKCH Minor Loop Link Channel Number 9 3 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 8 0x20 0,1,2,3,4,5,6,7 TCD%s_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0x1018 32 read-write 0 0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write 8 0x20 0,1,2,3,4,5,6,7 TCD%s_CSR TCD Control and Status 0x101C 16 read-write 0 0 START Channel Start 0 1 read-write 0 The channel is not explicitly started. #0 1 The channel is explicitly started via a software initiated service request. #1 INTMAJOR Enable an interrupt when major iteration count completes. 1 1 read-write 0 The end-of-major loop interrupt is disabled. #0 1 The end-of-major loop interrupt is enabled. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled. #0 1 The half-point interrupt is enabled. #1 DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected. #0 1 The channel's ERQ bit is cleared when the major loop is complete. #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled. #0 1 The channel-to-channel linking is enabled. #1 ACTIVE Channel Active 6 1 read-only DONE Channel Done 7 1 read-write MAJORLINKCH Major Loop Link Channel Number 8 3 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls. #00 10 eDMA engine stalls for 4 cycles after each R/W. #10 11 eDMA engine stalls for 8 cycles after each R/W. #11 8 0x20 0,1,2,3,4,5,6,7 TCD%s_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x101E 16 read-write 0 0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 8 0x20 0,1,2,3,4,5,6,7 TCD%s_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x101E 16 read-write 0 0 BITER Starting major iteration count 0 9 read-write LINKCH Link Channel Number 9 3 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 FTFE Flash Memory Interface FTFE_ 0x40020000 0 0x30 registers FTFE 5 FSTAT Flash Status Register 0 8 read-write 0 0xFF MGSTAT0 Memory Controller Command Completion Status Flag 0 1 read-only FPVIOL Flash Protection Violation Flag 4 1 read-write 0 No protection violation detected #0 1 Protection violation detected #1 ACCERR Flash Access Error Flag 5 1 read-write 0 No access error detected #0 1 Access error detected #1 RDCOLERR FTFE Read Collision Error Flag 6 1 read-write 0 No collision error detected #0 1 Collision error detected #1 CCIF Command Complete Interrupt Flag 7 1 read-write 0 FTFE command or EEPROM file system operation in progress #0 1 FTFE command or EEPROM file system operation has completed #1 FCNFG Flash Configuration Register 0x1 8 read-write 0 0xFF EEERDY This flag indicates if the EEPROM backup data has been copied to the FlexRAM and is therefore available for read access 0 1 read-only 0 FlexRAM is not available for EEPROM operation #0 1 FlexRAM is available for EEPROM operations where: reads from the FlexRAM return data previously written to the FlexRAM in EEPROM mode and writes launch an EEPROM operation to store the written data in the FlexRAM and EEPROM backup #1 RAMRDY RAM Ready 1 1 read-only 0 FlexRAM is not available for traditional RAM access #0 1 FlexRAM is available as traditional RAM only; writes to the FlexRAM do not trigger EEPROM operations #1 PFLSH FTFE configuration 2 1 read-only 0 FTFE configuration supports one program flash blocks and one FlexNVM block #0 ERSSUSP Erase Suspend 4 1 read-write 0 No suspend requested #0 1 Suspend the current Erase Flash Sector command execution #1 ERSAREQ Erase All Request 5 1 read-only 0 No request or request complete #0 1 Request to: run the Erase All Blocks command, verify the erased state, program the security byte in the Flash Configuration Field to the unsecure state, and release MCU security by setting the FSEC[SEC] field to the unsecure state #1 RDCOLLIE Read Collision Error Interrupt Enable 6 1 read-write 0 Read collision error interrupt disabled #0 1 Read collision error interrupt enabled. An interrupt request is generated whenever an FTFE read collision error is detected (see the description of FSTAT[RDCOLERR]). #1 CCIE Command Complete Interrupt Enable 7 1 read-write 0 Command complete interrupt disabled #0 1 Command complete interrupt enabled. An interrupt request is generated whenever the FSTAT[CCIF] flag is set. #1 FSEC Flash Security Register 0x2 8 read-only 0 0 SEC Flash Security 0 2 read-only 00 MCU security status is secure #00 01 MCU security status is secure #01 10 MCU security status is unsecure (The standard shipping condition of the FTFE is unsecure.) #10 11 MCU security status is secure #11 FSLACC Freescale Failure Analysis Access Code 2 2 read-only 00 Freescale factory access granted #00 01 Freescale factory access denied #01 10 Freescale factory access denied #10 11 Freescale factory access granted #11 MEEN Mass Erase Enable Bits 4 2 read-only 00 Mass erase is enabled #00 01 Mass erase is enabled #01 10 Mass erase is disabled #10 11 Mass erase is enabled #11 KEYEN Backdoor Key Security Enable 6 2 read-only 00 Backdoor key access disabled #00 01 Backdoor key access disabled (preferred KEYEN state to disable backdoor key access) #01 10 Backdoor key access enabled #10 11 Backdoor key access disabled #11 FOPT Flash Option Register 0x3 8 read-only 0 0 OPT Nonvolatile Option 0 8 read-only 12 0x1 3,2,1,0,7,6,5,4,B,A,9,8 FCCOB%s Flash Common Command Object Registers 0x4 8 read-write 0 0xFF CCOBn The FCCOB register provides a command code and relevant parameters to the memory controller 0 8 read-write 4 0x1 3,2,1,0 FPROT%s Program Flash Protection Registers 0x10 8 read-write 0 0 PROT Program Flash Region Protect 0 8 read-write 0 Program flash region is protected. #0 1 Program flash region is not protected #1 FEPROT EEPROM Protection Register 0x16 8 read-write 0 0 EPROT EEPROM Region Protect 0 8 read-write 0 EEPROM region is protected #0 1 EEPROM region is not protected #1 FDPROT Data Flash Protection Register 0x17 8 read-write 0 0 DPROT Data Flash Region Protect 0 8 read-write 0 Data Flash region is protected #0 1 Data Flash region is not protected #1 8 0x1 H3,H2,H1,H0,L3,L2,L1,L0 XACC%s Execute-only Access Registers 0x18 8 read-only 0 0 XA Execute-only access control 0 8 read-only 0 Associated segment is accessible in execute mode only (as an instruction fetch) #0 1 Associated segment is accessible as data or in execute mode #1 8 0x1 H3,H2,H1,H0,L3,L2,L1,L0 SACC%s Supervisor-only Access Registers 0x20 8 read-only 0 0 SA Supervisor-only access control 0 8 read-only 0 Associated segment is accessible in supervisor mode only #0 1 Associated segment is accessible in user or supervisor mode #1 FACSS Flash Access Segment Size Register 0x28 8 read-only 0 0 SGSIZE Segment Size 0 8 read-only FACSN Flash Access Segment Number Register 0x2B 8 read-only 0 0 NUMSG Number of Segments Indicator 0 8 read-only 110000 Program flash memory is divided into 48 segments (768 Kbytes, 1.5 Mbytes) #110000 1000000 Program flash memory is divided into 64 segments (512 Kbytes, 1 Mbyte, 2 Mbytes) #1000000 FERSTAT Flash Error Status Register 0x2E 8 read-write 0 0xFF DFDIF Double Bit Fault Detect Interrupt Flag 1 1 read-write 0 Double bit fault not detected during a valid flash read access from the platform flash controller #0 1 Double bit fault detected (or FERCNFG[FDFD] is set) during a valid flash read access from the platform flash controller #1 FERCNFG Flash Error Configuration Register 0x2F 8 read-write 0 0xFF DFDIE Double Bit Fault Detect Interrupt Enable 1 1 read-write 0 Double bit fault detect interrupt disabled #0 1 Double bit fault detect interrupt enabled. An interrupt request is generated whenever the FERSTAT[DFDIF] flag is set. #1 FDFD Force Double Bit Fault Detect 5 1 read-write 0 FERSTAT[DFDIF] sets only if a double bit fault is detected during read access from the platform flash controller #0 1 FERSTAT[DFDIF] sets during any valid flash read access from the platform flash controller. An interrupt request is generated if the DFDIE bit is set. #1 DMAMUX DMA channel multiplexor DMAMUX_ 0x40021000 0 0x8 registers 8 0x1 0,1,2,3,4,5,6,7 CHCFG%s Channel Configuration register 0 8 read-write 0 0xFF SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 LPUART0_Rx_Signal #10 3 LPUART0_Tx_Signal #11 4 LPUART1_Rx_Signal #100 5 LPUART1_Tx_Signal #101 6 LPUART2_Rx_Signal #110 7 LPUART2_Tx_Signal #111 10 FlexIO_Channel0_Signal #1010 11 FlexIO_Channel1_Signal #1011 12 FlexIO_Channel2_Signal #1100 13 FlexIO_Channel3_Signal #1101 14 LPSPI0_Rx_Signal #1110 15 LPSPI0_Tx_Signal #1111 16 LPSPI1_Rx_Signal #10000 17 LPSPI1_Tx_Signal #10001 18 LPI2C0_Rx_Signal #10010 19 LPI2C0_Tx_Signal #10011 20 FTM0_Channel0_Signal #10100 21 FTM0_Channel1_Signal #10101 22 FTM0_Channel2_Signal #10110 23 FTM0_Channel3_Signal #10111 24 FTM0_Channel4_Signal #11000 25 FTM0_Channel5_Signal #11001 26 FTM0_Channel6_Signal #11010 27 FTM0_Channel7_Signal #11011 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 30 FTM2_Channel0_Signal #11110 31 FTM2_Channel1_Signal #11111 32 LPI2C1_Rx_Signal #100000 33 LPI2C1_Tx_Signal #100001 40 ADC0_Signal #101000 41 ADC1_Signal #101001 43 CMP0_Signal #101011 44 CMP1_Signal #101100 46 PDB0_Signal #101110 49 PortA_Signal #110001 50 PortB_Signal #110010 51 PortC_Signal #110011 52 PortD_Signal #110100 53 PortE_Signal #110101 57 FTM1_Channel2_Signal #111001 58 FTM2_Channel2_Signal #111010 59 LPTMR0_Signal #111011 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 ADC0 Analog-to-Digital Converter ADC ADC0_ 0x4003B000 0 0xEC registers ADC0 15 2 0x4 A,B SC1%s ADC Status and Control Registers 1 0 32 read-write 0x1F 0xFFFFFFFF ADCH Input channel select 0 5 read-write 00000 AD0 is selected as input. #00000 00001 AD1 is selected as input. #00001 00010 AD2 is selected as input. #00010 00011 AD3 is selected as input. #00011 00100 AD4 is selected as input. #00100 00101 AD5 is selected as input. #00101 00110 AD6 is selected as input. #00110 00111 AD7 is selected as input. #00111 01000 AD8 is selected as input. #01000 01001 AD9 is selected as input. #01001 01010 AD10 is selected as input. #01010 01011 AD11 is selected as input. #01011 01100 AD12 is selected as input. #01100 01101 AD13 is selected as input. #01101 01110 AD14 is selected as input. #01110 01111 AD15 is selected as input. #01111 10010 AD18 is selected as input. #10010 10011 AD19 is selected as input. #10011 10101 AD21 is selected as input. #10101 10110 AD22 is selected as input. #10110 10111 AD23 is selected as input. #10111 11000 ATX Sense #11000 11001 ATX Force #11001 11010 Temp Sensor #11010 11011 Band Gap #11011 11100 AD28 is selected as input. #11100 11101 VREFSH is selected as input. Voltage reference selected is determined by SC2[REFSEL]. #11101 11110 VREFSL is selected as input. Voltage reference selected is determined by SC2[REFSEL]. #11110 11111 Module is disabled.. #11111 AIEN Interrupt Enable 6 1 read-write 0 Conversion complete interrupt is disabled. #0 1 Conversion complete interrupt is enabled. #1 COCO Conversion Complete Flag 7 1 read-only 0 Conversion is not completed. #0 1 Conversion is completed. #1 CFG1 ADC Configuration Register 1 0x40 32 read-write 0 0xFFFFFFFF ADICLK Input Clock Select 0 2 read-write 00 Alternate clock 1 (ADC_ALTCLK1) #00 01 Alternate clock 2 (ADC_ALTCLK2) #01 10 Alternate clock 3 (ADC_ALTCLK3) #10 11 Alternate clock 4 (ADC_ALTCLK4) #11 MODE Conversion mode selection 2 2 read-write 00 8-bit conversion. #00 01 12-bit conversion. #01 10 10-bit conversion. #10 ADIV Clock Divide Select 5 2 read-write 00 The divide ratio is 1 and the clock rate is input clock. #00 01 The divide ratio is 2 and the clock rate is (input clock)/2. #01 10 The divide ratio is 4 and the clock rate is (input clock)/4. #10 11 The divide ratio is 8 and the clock rate is (input clock)/8. #11 CFG2 ADC Configuration Register 2 0x44 32 read-write 0xC 0xFFFFFFFF SMPLTS Sample Time Select 0 8 read-write 2 0x4 A,B R%s ADC Data Result Register 0x48 32 read-only 0 0xFFFFFFFF D Data result 0 12 read-only 2 0x4 1,2 CV%s Compare Value Registers 0x88 32 read-write 0 0xFFFFFFFF CV Compare Value. 0 12 read-write SC2 Status and Control Register 2 0x90 32 read-write 0 0xFFFFFFFF REFSEL Voltage Reference Selection 0 2 read-write 00 Default voltage reference pin pair, that is, external pins VREFH and VREFL #00 01 Alternate reference pair, that is, VALTH and VALTL . This pair may be additional external pins or internal sources depending on the MCU configuration. See the chip configuration information for details specific to this MCU #01 DMAEN DMA Enable 2 1 read-write 0 DMA is disabled. #0 1 DMA is enabled and will assert the ADC DMA request during an ADC conversion complete event noted when any of the SC1n[COCO] flags is asserted. #1 ACREN Compare Function Range Enable 3 1 read-write 0 Range function disabled. Only CV1 is compared. #0 1 Range function enabled. Both CV1 and CV2 are compared. #1 ACFGT Compare Function Greater Than Enable 4 1 read-write 0 Configures less than threshold, outside range not inclusive and inside range not inclusive; functionality based on the values placed in CV1 and CV2. #0 1 Configures greater than or equal to threshold, outside and inside ranges inclusive; functionality based on the values placed in CV1 and CV2. #1 ACFE Compare Function Enable 5 1 read-write 0 Compare function disabled. #0 1 Compare function enabled. #1 ADTRG Conversion Trigger Select 6 1 read-write 0 Software trigger selected. #0 1 Hardware trigger selected. #1 ADACT Conversion Active 7 1 read-only 0 Conversion not in progress. #0 1 Conversion in progress. #1 SC3 Status and Control Register 3 0x94 32 read-write 0 0xFFFFFFFF AVGS Hardware Average Select 0 2 read-write 00 4 samples averaged. #00 01 8 samples averaged. #01 10 16 samples averaged. #10 11 32 samples averaged. #11 AVGE Hardware Average Enable 2 1 read-write 0 Hardware average function disabled. #0 1 Hardware average function enabled. #1 ADCO Continuous Conversion Enable 3 1 read-write 0 One conversion or one set of conversions if the hardware average function is enabled, that is, AVGE=1, after initiating a conversion. #0 1 Continuous conversions or sets of conversions if the hardware average function is enabled, that is, AVGE=1, after initiating a conversion. #1 CAL Calibration 7 1 read-write BASE_OFS BASE Offset Register 0x98 32 read-write 0x40 0xFFFFFFFF BA_OFS Base Offset Error Correction Value 0 8 read-write OFS ADC Offset Correction Register 0x9C 32 read-write 0 0xFFFFFFFF OFS Offset Error Correction Value 0 16 read-write USR_OFS USER Offset Correction Register 0xA0 32 read-write 0 0xFFFFFFFF USR_OFS USER Offset Error Correction Value 0 8 read-write XOFS ADC X Offset Correction Register 0xA4 32 read-write 0x30 0xFFFFFFFF OFS Offset Error Correction Value 0 6 read-write YOFS ADC Y Offset Correction Register 0xA8 32 read-write 0x37 0xFFFFFFFF YOFS Y Offset Error Correction Value 0 8 read-write G ADC Gain Register 0xAC 32 read-write 0x2F0 0xFFFFFFFF G Gain 0 11 read-write UG ADC User Gain Register 0xB0 32 read-write 0x4 0xFFFFFFFF UG User Gain 0 10 read-write CLPS ADC General Calibration Value Register 0xB4 32 read-write 0x2E 0xFFFFFFFF CLPS Calibration Value 0 7 read-write CLP3 ADC Plus-Side General Calibration Value Register 0xB8 32 read-write 0x180 0xFFFFFFFF CLP3 Calibration Value 0 10 read-write CLP2 ADC Plus-Side General Calibration Value Register 0xBC 32 read-write 0xB8 0xFFFFFFFF CLP2 Calibration Value 0 10 read-write CLP1 ADC Plus-Side General Calibration Value Register 0xC0 32 read-write 0x5C 0xFFFFFFFF CLP1 Calibration Value 0 9 read-write CLP0 ADC Plus-Side General Calibration Value Register 0xC4 32 read-write 0x2E 0xFFFFFFFF CLP0 Calibration Value 0 8 read-write CLPX ADC Plus-Side General Calibration Value Register 0xC8 32 read-write 0 0xFFFFFFFF CLPX Calibration Value 0 7 read-write CLPXEN CLPX compare bit 7 1 read-write CLP9 ADC Plus-Side General Calibration Value Register 0xCC 32 read-write 0 0xFFFFFFFF CLP9 Calibration Value 0 7 read-write CLP9EN CLP9 compare bit 7 1 read-write CLPS_OFS ADC General Calibration Value Register 0xD0 32 read-write 0 0xFFFFFFFF CLPS_OFS CLPS Offset 0 4 read-write CLP3_OFS ADC Plus-Side General Calibration Value Register 0xD4 32 read-write 0 0xFFFFFFFF CLP3_OFS CLP3 Offset 0 4 read-write CLP2_OFS ADC Plus-Side General Calibration Value Register 0xD8 32 read-write 0 0xFFFFFFFF CLP2_OFS CLP2 Offset 0 4 read-write CLP1_OFS ADC Plus-Side General Calibration Value Register 0xDC 32 read-write 0 0xFFFFFFFF CLP1_OFS CLP1 Offset 0 4 read-write CLP0_OFS ADC Plus-Side General Calibration Value Register 0xE0 32 read-write 0 0xFFFFFFFF CLP0_OFS CLP0 Offset 0 4 read-write CLPX_OFS ADC Plus-Side General Calibration Value Register 0xE4 32 read-write 0x440 0xFFFFFFFF CLPX_OFS CLPX Offset 0 12 read-write CLP9_OFS ADC Plus-Side General Calibration Value Register 0xE8 32 read-write 0x240 0xFFFFFFFF CLP9_OFS CLP9 Offset 0 12 read-write ADC1 Analog-to-Digital Converter ADC ADC1_ 0x40027000 0 0xEC registers ADC1 30 2 0x4 A,B SC1%s ADC Status and Control Registers 1 0 32 read-write 0x1F 0xFFFFFFFF ADCH Input channel select 0 5 read-write 00000 AD0 is selected as input. #00000 00001 AD1 is selected as input. #00001 00010 AD2 is selected as input. #00010 00011 AD3 is selected as input. #00011 00100 AD4 is selected as input. #00100 00101 AD5 is selected as input. #00101 00110 AD6 is selected as input. #00110 00111 AD7 is selected as input. #00111 01000 AD8 is selected as input. #01000 01001 AD9 is selected as input. #01001 01010 AD10 is selected as input. #01010 01011 AD11 is selected as input. #01011 01100 AD12 is selected as input. #01100 01101 AD13 is selected as input. #01101 01110 AD14 is selected as input. #01110 01111 AD15 is selected as input. #01111 10010 AD18 is selected as input. #10010 10011 AD19 is selected as input. #10011 10101 AD21 is selected as input. #10101 10110 AD22 is selected as input. #10110 10111 AD23 is selected as input. #10111 11000 ATX Sense #11000 11001 ATX Force #11001 11010 Temp Sensor #11010 11011 Band Gap #11011 11100 AD28 is selected as input. #11100 11101 VREFSH is selected as input. Voltage reference selected is determined by SC2[REFSEL]. #11101 11110 VREFSL is selected as input. Voltage reference selected is determined by SC2[REFSEL]. #11110 11111 Module is disabled.. #11111 AIEN Interrupt Enable 6 1 read-write 0 Conversion complete interrupt is disabled. #0 1 Conversion complete interrupt is enabled. #1 COCO Conversion Complete Flag 7 1 read-only 0 Conversion is not completed. #0 1 Conversion is completed. #1 CFG1 ADC Configuration Register 1 0x40 32 read-write 0 0xFFFFFFFF ADICLK Input Clock Select 0 2 read-write 00 Alternate clock 1 (ADC_ALTCLK1) #00 01 Alternate clock 2 (ADC_ALTCLK2) #01 10 Alternate clock 3 (ADC_ALTCLK3) #10 11 Alternate clock 4 (ADC_ALTCLK4) #11 MODE Conversion mode selection 2 2 read-write 00 8-bit conversion. #00 01 12-bit conversion. #01 10 10-bit conversion. #10 ADIV Clock Divide Select 5 2 read-write 00 The divide ratio is 1 and the clock rate is input clock. #00 01 The divide ratio is 2 and the clock rate is (input clock)/2. #01 10 The divide ratio is 4 and the clock rate is (input clock)/4. #10 11 The divide ratio is 8 and the clock rate is (input clock)/8. #11 CFG2 ADC Configuration Register 2 0x44 32 read-write 0xC 0xFFFFFFFF SMPLTS Sample Time Select 0 8 read-write 2 0x4 A,B R%s ADC Data Result Register 0x48 32 read-only 0 0xFFFFFFFF D Data result 0 12 read-only 2 0x4 1,2 CV%s Compare Value Registers 0x88 32 read-write 0 0xFFFFFFFF CV Compare Value. 0 12 read-write SC2 Status and Control Register 2 0x90 32 read-write 0 0xFFFFFFFF REFSEL Voltage Reference Selection 0 2 read-write 00 Default voltage reference pin pair, that is, external pins VREFH and VREFL #00 01 Alternate reference pair, that is, VALTH and VALTL . This pair may be additional external pins or internal sources depending on the MCU configuration. See the chip configuration information for details specific to this MCU #01 DMAEN DMA Enable 2 1 read-write 0 DMA is disabled. #0 1 DMA is enabled and will assert the ADC DMA request during an ADC conversion complete event noted when any of the SC1n[COCO] flags is asserted. #1 ACREN Compare Function Range Enable 3 1 read-write 0 Range function disabled. Only CV1 is compared. #0 1 Range function enabled. Both CV1 and CV2 are compared. #1 ACFGT Compare Function Greater Than Enable 4 1 read-write 0 Configures less than threshold, outside range not inclusive and inside range not inclusive; functionality based on the values placed in CV1 and CV2. #0 1 Configures greater than or equal to threshold, outside and inside ranges inclusive; functionality based on the values placed in CV1 and CV2. #1 ACFE Compare Function Enable 5 1 read-write 0 Compare function disabled. #0 1 Compare function enabled. #1 ADTRG Conversion Trigger Select 6 1 read-write 0 Software trigger selected. #0 1 Hardware trigger selected. #1 ADACT Conversion Active 7 1 read-only 0 Conversion not in progress. #0 1 Conversion in progress. #1 SC3 Status and Control Register 3 0x94 32 read-write 0 0xFFFFFFFF AVGS Hardware Average Select 0 2 read-write 00 4 samples averaged. #00 01 8 samples averaged. #01 10 16 samples averaged. #10 11 32 samples averaged. #11 AVGE Hardware Average Enable 2 1 read-write 0 Hardware average function disabled. #0 1 Hardware average function enabled. #1 ADCO Continuous Conversion Enable 3 1 read-write 0 One conversion or one set of conversions if the hardware average function is enabled, that is, AVGE=1, after initiating a conversion. #0 1 Continuous conversions or sets of conversions if the hardware average function is enabled, that is, AVGE=1, after initiating a conversion. #1 CAL Calibration 7 1 read-write BASE_OFS BASE Offset Register 0x98 32 read-write 0x40 0xFFFFFFFF BA_OFS Base Offset Error Correction Value 0 8 read-write OFS ADC Offset Correction Register 0x9C 32 read-write 0 0xFFFFFFFF OFS Offset Error Correction Value 0 16 read-write USR_OFS USER Offset Correction Register 0xA0 32 read-write 0 0xFFFFFFFF USR_OFS USER Offset Error Correction Value 0 8 read-write XOFS ADC X Offset Correction Register 0xA4 32 read-write 0x30 0xFFFFFFFF OFS Offset Error Correction Value 0 6 read-write YOFS ADC Y Offset Correction Register 0xA8 32 read-write 0x37 0xFFFFFFFF YOFS Y Offset Error Correction Value 0 8 read-write G ADC Gain Register 0xAC 32 read-write 0x2F0 0xFFFFFFFF G Gain 0 11 read-write UG ADC User Gain Register 0xB0 32 read-write 0x4 0xFFFFFFFF UG User Gain 0 10 read-write CLPS ADC General Calibration Value Register 0xB4 32 read-write 0x2E 0xFFFFFFFF CLPS Calibration Value 0 7 read-write CLP3 ADC Plus-Side General Calibration Value Register 0xB8 32 read-write 0x180 0xFFFFFFFF CLP3 Calibration Value 0 10 read-write CLP2 ADC Plus-Side General Calibration Value Register 0xBC 32 read-write 0xB8 0xFFFFFFFF CLP2 Calibration Value 0 10 read-write CLP1 ADC Plus-Side General Calibration Value Register 0xC0 32 read-write 0x5C 0xFFFFFFFF CLP1 Calibration Value 0 9 read-write CLP0 ADC Plus-Side General Calibration Value Register 0xC4 32 read-write 0x2E 0xFFFFFFFF CLP0 Calibration Value 0 8 read-write CLPX ADC Plus-Side General Calibration Value Register 0xC8 32 read-write 0 0xFFFFFFFF CLPX Calibration Value 0 7 read-write CLPXEN CLPX compare bit 7 1 read-write CLP9 ADC Plus-Side General Calibration Value Register 0xCC 32 read-write 0 0xFFFFFFFF CLP9 Calibration Value 0 7 read-write CLP9EN CLP9 compare bit 7 1 read-write CLPS_OFS ADC General Calibration Value Register 0xD0 32 read-write 0 0xFFFFFFFF CLPS_OFS CLPS Offset 0 4 read-write CLP3_OFS ADC Plus-Side General Calibration Value Register 0xD4 32 read-write 0 0xFFFFFFFF CLP3_OFS CLP3 Offset 0 4 read-write CLP2_OFS ADC Plus-Side General Calibration Value Register 0xD8 32 read-write 0 0xFFFFFFFF CLP2_OFS CLP2 Offset 0 4 read-write CLP1_OFS ADC Plus-Side General Calibration Value Register 0xDC 32 read-write 0 0xFFFFFFFF CLP1_OFS CLP1 Offset 0 4 read-write CLP0_OFS ADC Plus-Side General Calibration Value Register 0xE0 32 read-write 0 0xFFFFFFFF CLP0_OFS CLP0 Offset 0 4 read-write CLPX_OFS ADC Plus-Side General Calibration Value Register 0xE4 32 read-write 0x440 0xFFFFFFFF CLPX_OFS CLPX Offset 0 12 read-write CLP9_OFS ADC Plus-Side General Calibration Value Register 0xE8 32 read-write 0x240 0xFFFFFFFF CLP9_OFS CLP9 Offset 0 12 read-write LPSPI0 The LPSPI Memory Map/Register Definition can be found here. LPSPI LPSPI0_ 0x4002C000 0 0x78 registers LPSPI0 10 VERID Version ID Register 0 32 read-only 0x1000004 0xFFFFFFFF FEATURE Module Identification Number 0 16 read-only 100 Standard feature set supporting 32-bit shift register. #100 MINOR Minor Version Number 16 8 read-only MAJOR Major Version Number 24 8 read-only PARAM Parameter Register 0x4 32 read-only 0x202 0xFFFFFFFF TXFIFO Transmit FIFO Size 0 8 read-only RXFIFO Receive FIFO Size 8 8 read-only CR Control Register 0x10 32 read-write 0 0xFFFFFFFF MEN Module Enable 0 1 read-write 0 Module is disabled. #0 1 Module is enabled. #1 RST Software Reset 1 1 read-write 0 Master logic is not reset. #0 1 Master logic is reset. #1 DOZEN Doze mode enable 2 1 read-write 0 Module is enabled in Doze mode. #0 1 Module is disabled in Doze mode. #1 DBGEN Debug Enable 3 1 read-write 0 Module is disabled in debug mode. #0 1 Module is enabled in debug mode. #1 RTF Reset Transmit FIFO 8 1 write-only 0 No effect. #0 1 Transmit FIFO is reset. #1 RRF Reset Receive FIFO 9 1 write-only 0 No effect. #0 1 Receive FIFO is reset. #1 SR Status Register 0x14 32 read-write 0x1 0xFFFFFFFF TDF Transmit Data Flag 0 1 read-only 0 Transmit data not requested. #0 1 Transmit data is requested. #1 RDF Receive Data Flag 1 1 read-only 0 Receive Data is not ready. #0 1 Receive data is ready. #1 WCF Word Complete Flag 8 1 read-write 0 Transfer word not completed. #0 1 Transfer word completed. #1 FCF Frame Complete Flag 9 1 read-write 0 Frame transfer has not completed. #0 1 Frame transfer has completed. #1 TCF Transfer Complete Flag 10 1 read-write 0 All transfers have not completed. #0 1 All transfers have completed. #1 TEF Transmit Error Flag 11 1 read-write 0 Transmit FIFO underrun has not occurred. #0 1 Transmit FIFO underrun has occurred #1 REF Receive Error Flag 12 1 read-write 0 Receive FIFO has not overflowed. #0 1 Receive FIFO has overflowed. #1 DMF Data Match Flag 13 1 read-write 0 Have not received matching data. #0 1 Have received matching data. #1 MBF Module Busy Flag 24 1 read-only 0 LPSPI is idle. #0 1 LPSPI is busy. #1 IER Interrupt Enable Register 0x18 32 read-write 0 0xFFFFFFFF TDIE Transmit Data Interrupt Enable 0 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled #1 RDIE Receive Data Interrupt Enable 1 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 WCIE Word Complete Interrupt Enable 8 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 FCIE Frame Complete Interrupt Enable 9 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 TCIE Transfer Complete Interrupt Enable 10 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 TEIE Transmit Error Interrupt Enable 11 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 REIE Receive Error Interrupt Enable 12 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 DMIE Data Match Interrupt Enable 13 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 DER DMA Enable Register 0x1C 32 read-write 0 0xFFFFFFFF TDDE Transmit Data DMA Enable 0 1 read-write 0 DMA request disabled. #0 1 DMA request enabled #1 RDDE Receive Data DMA Enable 1 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 CFGR0 Configuration Register 0 0x20 32 read-write 0 0xFFFFFFFF HREN Host Request Enable 0 1 read-write 0 Host request is disabled. #0 1 Host request is enabled. #1 HRPOL Host Request Polarity 1 1 read-write 0 Active low. #0 1 Active high. #1 HRSEL Host Request Select 2 1 read-write 0 Host request input is pin LPSPI_HREQ. #0 1 Host request input is input trigger. #1 CIRFIFO Circular FIFO Enable 8 1 read-write 0 Circular FIFO is disabled. #0 1 Circular FIFO is enabled. #1 RDMO Receive Data Match Only 9 1 read-write 0 Received data is stored in the receive FIFO as normal. #0 1 Received data is discarded unless the DMF is set. #1 CFGR1 Configuration Register 1 0x24 32 read-write 0 0xFFFFFFFF MASTER Master Mode 0 1 read-write 0 Slave mode. #0 1 Master mode. #1 SAMPLE Sample Point 1 1 read-write 0 Input data sampled on SCK edge. #0 1 Input data sampled on delayed SCK edge. #1 AUTOPCS Automatic PCS 2 1 read-write 0 Automatic PCS generation disabled. #0 1 Automatic PCS generation enabled. #1 NOSTALL No Stall 3 1 read-write 0 Transfers will stall when transmit FIFO is empty or receive FIFO is full. #0 1 Transfers will not stall, allowing transmit FIFO underrun or receive FIFO overrun to occur. #1 PCSPOL Peripheral Chip Select Polarity 8 4 read-write 0 The PCSx is active low. #0000 1 The PCSx is active high. #0001 MATCFG Match Configuration 16 3 read-write 000 Match disabled. #000 010 Match enabled (1st data word equals MATCH0 OR MATCH1). #010 011 Match enabled (any data word equals MATCH0 OR MATCH1). #011 100 Match enabled (1st data word equals MATCH0 AND 2nd data word equals MATCH1). #100 101 Match enabled (any data word equals MATCH0 AND next data word equals MATCH1) #101 110 Match enabled (1st data word AND MATCH1 equals MATCH0 AND MATCH1) #110 111 Match enabled (any data word AND MATCH1 equals MATCH0 AND MATCH1). #111 PINCFG Pin Configuration 24 2 read-write 00 SIN is used for input data and SOUT for output data. #00 01 SIN is used for both input and output data. #01 10 SOUT is used for both input and output data. #10 11 SOUT is used for input data and SIN for output data. #11 OUTCFG Output Config 26 1 read-write 0 Output data retains last value when chip select is negated. #0 1 Output data is tristated when chip select is negated. #1 PCSCFG Peripheral Chip Select Configuration 27 1 read-write 0 PCS[3:2] are enabled. #0 1 PCS[3:2] are disabled. #1 DMR0 Data Match Register 0 0x30 32 read-write 0 0xFFFFFFFF MATCH0 Match 0 Value 0 32 read-write DMR1 Data Match Register 1 0x34 32 read-write 0 0xFFFFFFFF MATCH1 Match 1 Value 0 32 read-write CCR Clock Configuration Register 0x40 32 read-write 0 0xFFFFFFFF SCKDIV SCK Divider 0 8 read-write DBT Delay Between Transfers 8 8 read-write PCSSCK PCS to SCK Delay 16 8 read-write SCKPCS SCK to PCS Delay 24 8 read-write FCR FIFO Control Register 0x58 32 read-write 0 0xFFFFFFFF TXWATER Transmit FIFO Watermark 0 8 read-write RXWATER Receive FIFO Watermark 16 8 read-write FSR FIFO Status Register 0x5C 32 read-only 0 0xFFFFFFFF TXCOUNT Transmit FIFO Count 0 8 read-only RXCOUNT Receive FIFO Count 16 8 read-only TCR Transmit Command Register 0x60 32 read-write 0x1F 0xFFFFFFFF FRAMESZ Frame Size 0 12 read-write WIDTH Transfer Width 16 2 read-write 00 Single bit transfer. #00 01 Two bit transfer. #01 10 Four bit transfer. #10 TXMSK Transmit Data Mask 18 1 read-write 00 Normal transfer. #0 01 Mask transmit data. #1 RXMSK Receive Data Mask 19 1 read-write 0 Normal transfer. #0 1 Receive data is masked. #1 CONTC Continuing Command 20 1 read-write 0 Command word for start of new transfer. #0 1 Command word for continuing transfer. #1 CONT Continuous Transfer 21 1 read-write 0 Continuous transfer disabled. #0 1 Continuous transfer enabled. #1 BYSW Byte Swap 22 1 read-write 0 Byte swap disabled. #0 1 Byte swap enabled. #1 LSBF LSB First 23 1 read-write 0 Data is transferred MSB first. #0 1 Data is transferred LSB first. #1 PCS Peripheral Chip Select 24 2 read-write 00 Transfer using LPSPI_PCS[0] #00 01 Transfer using LPSPI_PCS[1] #01 10 Transfer using LPSPI_PCS[2] #10 11 Transfer using LPSPI_PCS[3] #11 PRESCALE Prescaler Value 27 3 read-write 000 Divide by 1. #000 001 Divide by 2. #001 010 Divide by 4. #010 011 Divide by 8. #011 100 Divide by 16. #100 101 Divide by 32. #101 110 Divide by 64. #110 111 Divide by 128. #111 CPHA Clock Phase 30 1 read-write 0 Data is captured on the leading edge of SCK and changed on the following edge. #0 1 Data is changed on the leading edge of SCK and captured on the following edge. #1 CPOL Clock Polarity 31 1 read-write 0 The inactive state value of SCK is low. #0 1 The inactive state value of SCK is high. #1 TDR Transmit Data Register 0x64 32 write-only 0 0xFFFFFFFF DATA Transmit Data 0 32 write-only RSR Receive Status Register 0x70 32 read-only 0x2 0xFFFFFFFF SOF Start Of Frame 0 1 read-only 0 Subsequent data word received after LPSPI_PCS assertion. #0 1 First data word received after LPSPI_PCS assertion. #1 RXEMPTY RX FIFO Empty 1 1 read-only 0 RX FIFO is not empty. #0 1 RX FIFO is empty. #1 RDR Receive Data Register 0x74 32 read-only 0 0xFFFFFFFF DATA Receive Data 0 32 read-only LPSPI1 The LPSPI Memory Map/Register Definition can be found here. LPSPI LPSPI1_ 0x4002D000 0 0x78 registers LPSPI1 11 VERID Version ID Register 0 32 read-only 0x1000004 0xFFFFFFFF FEATURE Module Identification Number 0 16 read-only 100 Standard feature set supporting 32-bit shift register. #100 MINOR Minor Version Number 16 8 read-only MAJOR Major Version Number 24 8 read-only PARAM Parameter Register 0x4 32 read-only 0x202 0xFFFFFFFF TXFIFO Transmit FIFO Size 0 8 read-only RXFIFO Receive FIFO Size 8 8 read-only CR Control Register 0x10 32 read-write 0 0xFFFFFFFF MEN Module Enable 0 1 read-write 0 Module is disabled. #0 1 Module is enabled. #1 RST Software Reset 1 1 read-write 0 Master logic is not reset. #0 1 Master logic is reset. #1 DOZEN Doze mode enable 2 1 read-write 0 Module is enabled in Doze mode. #0 1 Module is disabled in Doze mode. #1 DBGEN Debug Enable 3 1 read-write 0 Module is disabled in debug mode. #0 1 Module is enabled in debug mode. #1 RTF Reset Transmit FIFO 8 1 write-only 0 No effect. #0 1 Transmit FIFO is reset. #1 RRF Reset Receive FIFO 9 1 write-only 0 No effect. #0 1 Receive FIFO is reset. #1 SR Status Register 0x14 32 read-write 0x1 0xFFFFFFFF TDF Transmit Data Flag 0 1 read-only 0 Transmit data not requested. #0 1 Transmit data is requested. #1 RDF Receive Data Flag 1 1 read-only 0 Receive Data is not ready. #0 1 Receive data is ready. #1 WCF Word Complete Flag 8 1 read-write 0 Transfer word not completed. #0 1 Transfer word completed. #1 FCF Frame Complete Flag 9 1 read-write 0 Frame transfer has not completed. #0 1 Frame transfer has completed. #1 TCF Transfer Complete Flag 10 1 read-write 0 All transfers have not completed. #0 1 All transfers have completed. #1 TEF Transmit Error Flag 11 1 read-write 0 Transmit FIFO underrun has not occurred. #0 1 Transmit FIFO underrun has occurred #1 REF Receive Error Flag 12 1 read-write 0 Receive FIFO has not overflowed. #0 1 Receive FIFO has overflowed. #1 DMF Data Match Flag 13 1 read-write 0 Have not received matching data. #0 1 Have received matching data. #1 MBF Module Busy Flag 24 1 read-only 0 LPSPI is idle. #0 1 LPSPI is busy. #1 IER Interrupt Enable Register 0x18 32 read-write 0 0xFFFFFFFF TDIE Transmit Data Interrupt Enable 0 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled #1 RDIE Receive Data Interrupt Enable 1 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 WCIE Word Complete Interrupt Enable 8 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 FCIE Frame Complete Interrupt Enable 9 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 TCIE Transfer Complete Interrupt Enable 10 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 TEIE Transmit Error Interrupt Enable 11 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 REIE Receive Error Interrupt Enable 12 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 DMIE Data Match Interrupt Enable 13 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 DER DMA Enable Register 0x1C 32 read-write 0 0xFFFFFFFF TDDE Transmit Data DMA Enable 0 1 read-write 0 DMA request disabled. #0 1 DMA request enabled #1 RDDE Receive Data DMA Enable 1 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 CFGR0 Configuration Register 0 0x20 32 read-write 0 0xFFFFFFFF HREN Host Request Enable 0 1 read-write 0 Host request is disabled. #0 1 Host request is enabled. #1 HRPOL Host Request Polarity 1 1 read-write 0 Active low. #0 1 Active high. #1 HRSEL Host Request Select 2 1 read-write 0 Host request input is pin LPSPI_HREQ. #0 1 Host request input is input trigger. #1 CIRFIFO Circular FIFO Enable 8 1 read-write 0 Circular FIFO is disabled. #0 1 Circular FIFO is enabled. #1 RDMO Receive Data Match Only 9 1 read-write 0 Received data is stored in the receive FIFO as normal. #0 1 Received data is discarded unless the DMF is set. #1 CFGR1 Configuration Register 1 0x24 32 read-write 0 0xFFFFFFFF MASTER Master Mode 0 1 read-write 0 Slave mode. #0 1 Master mode. #1 SAMPLE Sample Point 1 1 read-write 0 Input data sampled on SCK edge. #0 1 Input data sampled on delayed SCK edge. #1 AUTOPCS Automatic PCS 2 1 read-write 0 Automatic PCS generation disabled. #0 1 Automatic PCS generation enabled. #1 NOSTALL No Stall 3 1 read-write 0 Transfers will stall when transmit FIFO is empty or receive FIFO is full. #0 1 Transfers will not stall, allowing transmit FIFO underrun or receive FIFO overrun to occur. #1 PCSPOL Peripheral Chip Select Polarity 8 4 read-write 0 The PCSx is active low. #0000 1 The PCSx is active high. #0001 MATCFG Match Configuration 16 3 read-write 000 Match disabled. #000 010 Match enabled (1st data word equals MATCH0 OR MATCH1). #010 011 Match enabled (any data word equals MATCH0 OR MATCH1). #011 100 Match enabled (1st data word equals MATCH0 AND 2nd data word equals MATCH1). #100 101 Match enabled (any data word equals MATCH0 AND next data word equals MATCH1) #101 110 Match enabled (1st data word AND MATCH1 equals MATCH0 AND MATCH1) #110 111 Match enabled (any data word AND MATCH1 equals MATCH0 AND MATCH1). #111 PINCFG Pin Configuration 24 2 read-write 00 SIN is used for input data and SOUT for output data. #00 01 SIN is used for both input and output data. #01 10 SOUT is used for both input and output data. #10 11 SOUT is used for input data and SIN for output data. #11 OUTCFG Output Config 26 1 read-write 0 Output data retains last value when chip select is negated. #0 1 Output data is tristated when chip select is negated. #1 PCSCFG Peripheral Chip Select Configuration 27 1 read-write 0 PCS[3:2] are enabled. #0 1 PCS[3:2] are disabled. #1 DMR0 Data Match Register 0 0x30 32 read-write 0 0xFFFFFFFF MATCH0 Match 0 Value 0 32 read-write DMR1 Data Match Register 1 0x34 32 read-write 0 0xFFFFFFFF MATCH1 Match 1 Value 0 32 read-write CCR Clock Configuration Register 0x40 32 read-write 0 0xFFFFFFFF SCKDIV SCK Divider 0 8 read-write DBT Delay Between Transfers 8 8 read-write PCSSCK PCS to SCK Delay 16 8 read-write SCKPCS SCK to PCS Delay 24 8 read-write FCR FIFO Control Register 0x58 32 read-write 0 0xFFFFFFFF TXWATER Transmit FIFO Watermark 0 8 read-write RXWATER Receive FIFO Watermark 16 8 read-write FSR FIFO Status Register 0x5C 32 read-only 0 0xFFFFFFFF TXCOUNT Transmit FIFO Count 0 8 read-only RXCOUNT Receive FIFO Count 16 8 read-only TCR Transmit Command Register 0x60 32 read-write 0x1F 0xFFFFFFFF FRAMESZ Frame Size 0 12 read-write WIDTH Transfer Width 16 2 read-write 00 Single bit transfer. #00 01 Two bit transfer. #01 10 Four bit transfer. #10 TXMSK Transmit Data Mask 18 1 read-write 00 Normal transfer. #0 01 Mask transmit data. #1 RXMSK Receive Data Mask 19 1 read-write 0 Normal transfer. #0 1 Receive data is masked. #1 CONTC Continuing Command 20 1 read-write 0 Command word for start of new transfer. #0 1 Command word for continuing transfer. #1 CONT Continuous Transfer 21 1 read-write 0 Continuous transfer disabled. #0 1 Continuous transfer enabled. #1 BYSW Byte Swap 22 1 read-write 0 Byte swap disabled. #0 1 Byte swap enabled. #1 LSBF LSB First 23 1 read-write 0 Data is transferred MSB first. #0 1 Data is transferred LSB first. #1 PCS Peripheral Chip Select 24 2 read-write 00 Transfer using LPSPI_PCS[0] #00 01 Transfer using LPSPI_PCS[1] #01 10 Transfer using LPSPI_PCS[2] #10 11 Transfer using LPSPI_PCS[3] #11 PRESCALE Prescaler Value 27 3 read-write 000 Divide by 1. #000 001 Divide by 2. #001 010 Divide by 4. #010 011 Divide by 8. #011 100 Divide by 16. #100 101 Divide by 32. #101 110 Divide by 64. #110 111 Divide by 128. #111 CPHA Clock Phase 30 1 read-write 0 Data is captured on the leading edge of SCK and changed on the following edge. #0 1 Data is changed on the leading edge of SCK and captured on the following edge. #1 CPOL Clock Polarity 31 1 read-write 0 The inactive state value of SCK is low. #0 1 The inactive state value of SCK is high. #1 TDR Transmit Data Register 0x64 32 write-only 0 0xFFFFFFFF DATA Transmit Data 0 32 write-only RSR Receive Status Register 0x70 32 read-only 0x2 0xFFFFFFFF SOF Start Of Frame 0 1 read-only 0 Subsequent data word received after LPSPI_PCS assertion. #0 1 First data word received after LPSPI_PCS assertion. #1 RXEMPTY RX FIFO Empty 1 1 read-only 0 RX FIFO is not empty. #0 1 RX FIFO is empty. #1 RDR Receive Data Register 0x74 32 read-only 0 0xFFFFFFFF DATA Receive Data 0 32 read-only CRC Cyclic Redundancy Check CRC_ 0x40032000 0 0xC registers DATA CRC Data register CRC 0 32 read-write 0xFFFFFFFF 0xFFFFFFFF LL CRC Low Lower Byte 0 8 read-write LU CRC Low Upper Byte 8 8 read-write HL CRC High Lower Byte 16 8 read-write HU CRC High Upper Byte 24 8 read-write DATAL CRC_DATAL register. CRC 0 16 read-write 0xFFFF 0xFFFF DATAL DATAL stores the lower 16 bits of the 16/32 bit CRC 0 16 read-write DATALL CRC_DATALL register. CRC 0 8 read-write 0xFF 0xFF DATALL CRCLL stores the first 8 bits of the 32 bit DATA 0 8 read-write DATALU CRC_DATALU register. 0x1 8 read-write 0xFF 0xFF DATALU DATALL stores the second 8 bits of the 32 bit CRC 0 8 read-write DATAH CRC_DATAH register. CRC 0x2 16 read-write 0xFFFF 0xFFFF DATAH DATAH stores the high 16 bits of the 16/32 bit CRC 0 16 read-write DATAHL CRC_DATAHL register. CRC 0x2 8 read-write 0xFF 0xFF DATAHL DATAHL stores the third 8 bits of the 32 bit CRC 0 8 read-write DATAHU CRC_DATAHU register. 0x3 8 read-write 0xFF 0xFF DATAHU DATAHU stores the fourth 8 bits of the 32 bit CRC 0 8 read-write GPOLY CRC Polynomial register CRC 0x4 32 read-write 0x1021 0xFFFFFFFF LOW Low Polynominal Half-word 0 16 read-write HIGH High Polynominal Half-word 16 16 read-write GPOLYL CRC_GPOLYL register. CRC 0x4 16 read-write 0xFFFF 0xFFFF GPOLYL POLYL stores the lower 16 bits of the 16/32 bit CRC polynomial value 0 16 read-write GPOLYLL CRC_GPOLYLL register. CRC 0x4 8 read-write 0xFF 0xFF GPOLYLL POLYLL stores the first 8 bits of the 32 bit CRC 0 8 read-write GPOLYLU CRC_GPOLYLU register. 0x5 8 read-write 0xFF 0xFF GPOLYLU POLYLL stores the second 8 bits of the 32 bit CRC 0 8 read-write GPOLYH CRC_GPOLYH register. CRC 0x6 16 read-write 0xFFFF 0xFFFF GPOLYH POLYH stores the high 16 bits of the 16/32 bit CRC polynomial value 0 16 read-write GPOLYHL CRC_GPOLYHL register. CRC 0x6 8 read-write 0xFF 0xFF GPOLYHL POLYHL stores the third 8 bits of the 32 bit CRC 0 8 read-write GPOLYHU CRC_GPOLYHU register. 0x7 8 read-write 0xFF 0xFF GPOLYHU POLYHU stores the fourth 8 bits of the 32 bit CRC 0 8 read-write CTRL CRC Control register 0x8 32 read-write 0 0xFFFFFFFF TCRC Width of CRC protocol. 24 1 read-write 0 16-bit CRC protocol. #0 1 32-bit CRC protocol. #1 WAS Write CRC Data Register As Seed 25 1 read-write 0 Writes to the CRC data register are data values. #0 1 Writes to the CRC data register are seed values. #1 FXOR Complement Read Of CRC Data Register 26 1 read-write 0 No XOR on reading. #0 1 Invert or complement the read value of the CRC Data register. #1 TOTR Type Of Transpose For Read 28 2 read-write 00 No transposition. #00 01 Bits in bytes are transposed; bytes are not transposed. #01 10 Both bits in bytes and bytes are transposed. #10 11 Only bytes are transposed; no bits in a byte are transposed. #11 TOT Type Of Transpose For Writes 30 2 read-write 00 No transposition. #00 01 Bits in bytes are transposed; bytes are not transposed. #01 10 Both bits in bytes and bytes are transposed. #10 11 Only bytes are transposed; no bits in a byte are transposed. #11 CTRLHU CRC_CTRLHU register. 0xB 8 read-write 0 0xFF TCRC no description available 0 1 read-write 0 16-bit CRC protocol. #0 1 32-bit CRC protocol. #1 WAS no description available 1 1 read-write 0 Writes to CRC data register are data values. #0 1 Writes to CRC data reguster are seed values. #1 FXOR no description available 2 1 read-write 0 No XOR on reading. #0 1 Invert or complement the read value of CRC data register. #1 TOTR no description available 4 2 read-write 00 No Transposition. #00 01 Bits in bytes are transposed, bytes are not transposed. #01 10 Both bits in bytes and bytes are transposed. #10 11 Only bytes are transposed; no bits in a byte are transposed. #11 TOT no description available 6 2 read-write 00 No Transposition. #00 01 Bits in bytes are transposed, bytes are not transposed. #01 10 Both bits in bytes and bytes are transposed. #10 11 Only bytes are transposed; no bits in a byte are transposed. #11 PDB0 Programmable Delay Block PDB0_ 0x40036000 0 0x19C registers PDB0 25 SC Status and Control register 0 32 read-write 0 0xFFFFFFFF LDOK Load OK 0 1 read-write CONT Continuous Mode Enable 1 1 read-write 0 PDB operation in One-Shot mode #0 1 PDB operation in Continuous mode #1 MULT Multiplication Factor Select for Prescaler 2 2 read-write 00 Multiplication factor is 1. #00 01 Multiplication factor is 10. #01 10 Multiplication factor is 20. #10 11 Multiplication factor is 40. #11 PDBIE PDB Interrupt Enable 5 1 read-write 0 PDB interrupt disabled. #0 1 PDB interrupt enabled. #1 PDBIF PDB Interrupt Flag 6 1 read-write PDBEN PDB Enable 7 1 read-write 0 PDB disabled. Counter is off. #0 1 PDB enabled. #1 TRGSEL Trigger Input Source Select 8 4 read-write 0000 Trigger-In 0 is selected. #0000 0001 Trigger-In 1 is selected. #0001 0010 Trigger-In 2 is selected. #0010 0011 Trigger-In 3 is selected. #0011 0100 Trigger-In 4 is selected. #0100 0101 Trigger-In 5 is selected. #0101 0110 Trigger-In 6 is selected. #0110 0111 Trigger-In 7 is selected. #0111 1000 Trigger-In 8 is selected. #1000 1001 Trigger-In 9 is selected. #1001 1010 Trigger-In 10 is selected. #1010 1011 Trigger-In 11 is selected. #1011 1100 Trigger-In 12 is selected. #1100 1101 Trigger-In 13 is selected. #1101 1110 Trigger-In 14 is selected. #1110 1111 Software trigger is selected. #1111 PRESCALER Prescaler Divider Select 12 3 read-write 000 Counting uses the peripheral clock divided by multiplication factor selected by MULT. #000 001 Counting uses the peripheral clock divided by twice of the multiplication factor selected by MULT. #001 010 Counting uses the peripheral clock divided by four times of the multiplication factor selected by MULT. #010 011 Counting uses the peripheral clock divided by eight times of the multiplication factor selected by MULT. #011 100 Counting uses the peripheral clock divided by 16 times of the multiplication factor selected by MULT. #100 101 Counting uses the peripheral clock divided by 32 times of the multiplication factor selected by MULT. #101 110 Counting uses the peripheral clock divided by 64 times of the multiplication factor selected by MULT. #110 111 Counting uses the peripheral clock divided by 128 times of the multiplication factor selected by MULT. #111 DMAEN DMA Enable 15 1 read-write 0 DMA disabled. #0 1 DMA enabled. #1 SWTRIG Software Trigger 16 1 write-only PDBEIE PDB Sequence Error Interrupt Enable 17 1 read-write 0 PDB sequence error interrupt disabled. #0 1 PDB sequence error interrupt enabled. #1 LDMOD Load Mode Select 18 2 read-write 00 The internal registers are loaded with the values from their buffers immediately after 1 is written to LDOK. #00 01 The internal registers are loaded with the values from their buffers when the PDB counter reaches the MOD register value after 1 is written to LDOK. #01 10 The internal registers are loaded with the values from their buffers when a trigger input event is detected after 1 is written to LDOK. #10 11 The internal registers are loaded with the values from their buffers when either the PDB counter reaches the MOD register value or a trigger input event is detected, after 1 is written to LDOK. #11 MOD Modulus register 0x4 32 read-write 0xFFFF 0xFFFFFFFF MOD PDB Modulus 0 16 read-write CNT Counter register 0x8 32 read-only 0 0xFFFFFFFF CNT PDB Counter 0 16 read-only IDLY Interrupt Delay register 0xC 32 read-write 0xFFFF 0xFFFFFFFF IDLY PDB Interrupt Delay 0 16 read-write 2 0x28 0,1 CH%sC1 Channel n Control register 1 0x10 32 read-write 0 0xFFFFFFFF EN PDB Channel Pre-Trigger Enable 0 8 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 TOS PDB Channel Pre-Trigger Output Select 8 8 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 BB PDB Channel Pre-Trigger Back-to-Back Operation Enable 16 8 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 2 0x28 0,1 CH%sS Channel n Status register 0x14 32 read-write 0 0xFFFFFFFF ERR PDB Channel Sequence Error Flags 0 8 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 CF PDB Channel Flags 16 8 read-write 2 0x28 0,1 CH%sDLY0 Channel n Delay 0 register 0x18 32 read-write 0 0xFFFFFFFF DLY PDB Channel Delay 0 16 read-write 2 0x28 0,1 CH%sDLY1 Channel n Delay 1 register 0x1C 32 read-write 0 0xFFFFFFFF DLY PDB Channel Delay 0 16 read-write POEN Pulse-Out n Enable register 0x190 32 read-write 0 0xFFFFFFFF POEN PDB Pulse-Out Enable 0 8 read-write 0 PDB Pulse-Out disabled #0 1 PDB Pulse-Out enabled #1 2 0x4 0,1 PO%sDLY Pulse-Out n Delay register 0x194 32 read-write 0 0xFFFFFFFF DLY2 PDB Pulse-Out Delay 2 0 16 read-write DLY1 PDB Pulse-Out Delay 1 16 16 read-write LPIT0 Low Power Periodic Interrupt Timer (LPIT) LPIT0_ 0x40037000 0 0x5C registers LPIT0 22 VERID Version ID Register 0 32 read-only 0x1000000 0xFFFFFFFF FEATURE Feature Number 0 16 read-only MINOR Minor Version Number 16 8 read-only MAJOR Major Version Number 24 8 read-only PARAM Parameter Register 0x4 32 read-only 0x404 0xFFFFFFFF CHANNEL Number of Timer Channels 0 8 read-only EXT_TRIG Number of External Trigger Inputs 8 8 read-only MCR Module Control Register 0x8 32 read-write 0 0xFFFFFFFF M_CEN Module Clock Enable 0 1 read-write 0 Protocol clock to timers is disabled #0 1 Protocol clock to timers is enabled #1 SW_RST Software Reset Bit 1 1 read-write 0 Timer channels and registers are not reset #0 1 Timer channels and registers are reset #1 DOZE_EN DOZE Mode Enable Bit 2 1 read-write 0 Timer channels are stopped in DOZE mode #0 1 Timer channels continue to run in DOZE mode #1 DBG_EN Debug Enable Bit 3 1 read-write 0 Timer channels are stopped in Debug mode #0 1 Timer channels continue to run in Debug mode #1 MSR Module Status Register 0xC 32 read-write 0 0xFFFFFFFF TIF0 Channel 0 Timer Interrupt Flag 0 1 read-write 0 Timer has not timed out #0 1 Timeout has occurred #1 TIF1 Channel 1 Timer Interrupt Flag 1 1 read-write 0 Timer has not timed out #0 1 Timeout has occurred #1 TIF2 Channel 2 Timer Interrupt Flag 2 1 read-write 0 Timer has not timed out #0 1 Timeout has occurred #1 TIF3 Channel 3 Timer Interrupt Flag 3 1 read-write 0 Timer has not timed out #0 1 Timeout has occurred #1 MIER Module Interrupt Enable Register 0x10 32 read-write 0 0xFFFFFFFF TIE0 Channel 0 Timer Interrupt Enable 0 1 read-write 0 Interrupt generation is disabled #0 1 Interrupt generation is enabled #1 TIE1 Channel 1 Timer Interrupt Enable 1 1 read-write 0 Interrupt generation is disabled #0 1 Interrupt generation is enabled #1 TIE2 Channel 2 Timer Interrupt Enable 2 1 read-write 0 Interrupt generation is disabled #0 1 Interrupt generation is enabled #1 TIE3 Channel 3 Timer Interrupt Enable 3 1 read-write 0 Interrupt generation is disabled #0 1 Interrupt generation is enabled #1 SETTEN Set Timer Enable Register 0x14 32 read-write 0 0xFFFFFFFF SET_T_EN_0 Set Timer 0 Enable 0 1 read-write 0 No effect #0 1 Enables the Timer Channel 0 #1 SET_T_EN_1 Set Timer 1 Enable 1 1 read-write 0 No Effect #0 1 Enables the Timer Channel 1 #1 SET_T_EN_2 Set Timer 2 Enable 2 1 read-write 0 No Effect #0 1 Enables the Timer Channel 2 #1 SET_T_EN_3 Set Timer 3 Enable 3 1 read-write 0 No effect #0 1 Enables the Timer Channel 3 #1 CLRTEN Clear Timer Enable Register 0x18 32 read-write 0 0xFFFFFFFF CLR_T_EN_0 Clear Timer 0 Enable 0 1 write-only 0 No action #0 1 Clear T_EN bit for Timer Channel 0 #1 CLR_T_EN_1 Clear Timer 1 Enable 1 1 write-only 0 No Action #0 1 Clear T_EN bit for Timer Channel 1 #1 CLR_T_EN_2 Clear Timer 2 Enable 2 1 write-only 0 No Action #0 1 Clear T_EN bit for Timer Channel 2 #1 CLR_T_EN_3 Clear Timer 3 Enable 3 1 write-only 0 No Action #0 1 Clear T_EN bit for Timer Channel 3 #1 4 0x10 0,1,2,3 TVAL%s Timer Value Register 0x20 32 read-write 0 0xFFFFFFFF TMR_VAL Timer Value 0 32 read-write 0 Invalid load value in compare modes #0 4 0x10 0,1,2,3 CVAL%s Current Timer Value 0x24 32 read-only 0xFFFFFFFF 0xFFFFFFFF TMR_CUR_VAL Current Timer Value 0 32 read-only 4 0x10 0,1,2,3 TCTRL%s Timer Control Register 0x28 32 read-write 0 0xFFFFFFFF T_EN Timer Enable 0 1 read-write 0 Timer Channel is disabled #0 1 Timer Channel is enabled #1 CHAIN Chain Channel 1 1 read-write 0 Channel Chaining is disabled. Channel Timer runs independently. #0 1 Channel Chaining is enabled. Timer decrements on previous channel's timeout #1 MODE Timer Operation Mode 2 2 read-write 00 32-bit Periodic Counter #00 01 Dual 16-bit Periodic Counter #01 10 32-bit Trigger Accumulator #10 11 32-bit Trigger Input Capture #11 TSOT Timer Start On Trigger 16 1 read-write 0 Timer starts to decrement immediately based on restart condition (controlled by TSOI bit) #0 1 Timer starts to decrement when rising edge on selected trigger is detected #1 TSOI Timer Stop On Interrupt 17 1 read-write 0 Timer does not stop after timeout #0 1 Timer will stop after timeout and will restart after rising edge on the T_EN bit is detected (i.e. timer channel is disabled and then enabled) #1 TROT Timer Reload On Trigger 18 1 read-write 0 Timer will not reload on selected trigger #0 1 Timer will reload on selected trigger #1 TRG_SRC Trigger Source 23 1 read-write 0 Trigger source selected in external #0 1 Trigger source selected is the internal trigger #1 TRG_SEL Trigger Select 24 4 read-write 0 Timer channel 0 trigger source is selected #0000 1 Timer channel 1 trigger source is selected #0001 10 Timer channel 2 trigger source is selected #0010 FTM0 FlexTimer Module FTM FTM0_ 0x40038000 0 0x224 registers FTM0 17 SC Status And Control 0 32 read-write 0 0xFFFFFFFF PS Prescale Factor Selection 0 3 read-write 000 Divide by 1 #000 001 Divide by 2 #001 010 Divide by 4 #010 011 Divide by 8 #011 100 Divide by 16 #100 101 Divide by 32 #101 110 Divide by 64 #110 111 Divide by 128 #111 CLKS Clock Source Selection 3 2 read-write 00 No clock selected. This in effect disables the FTM counter. #00 01 System clock #01 10 Fixed frequency clock #10 11 External clock #11 CPWMS Center-Aligned PWM Select 5 1 read-write 0 FTM counter operates in Up Counting mode. #0 1 FTM counter operates in Up-Down Counting mode. #1 RIE Reload Interrupt Enable 6 1 read-write 0 Reload interrupt is disabled. #0 1 Reload interrupt is enabled. #1 RF Reload Flag 7 1 read-only 0 FTM counter did not reach a reload point. #0 1 FTM counter reached a reload point. #1 TOIE Timer Overflow Interrupt Enable 8 1 read-write 0 Disable TOF interrupts. Use software polling. #0 1 Enable TOF interrupts. An interrupt is generated when TOF equals one. #1 TOF Timer Overflow Flag 9 1 read-only 0 FTM counter has not overflowed. #0 1 FTM counter has overflowed. #1 PWMEN0 Channel 0 PWM enable bit 16 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN1 Channel 1 PWM enable bit 17 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN2 Channel 2 PWM enable bit 18 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN3 Channel 3 PWM enable bit 19 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN4 Channel 4 PWM enable bit 20 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN5 Channel 5 PWM enable bit 21 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN6 Channel 6 PWM enable bit 22 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN7 Channel 7 PWM enable bit 23 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 CNT Counter 0x4 32 read-write 0 0xFFFFFFFF COUNT Counter Value 0 16 read-write MOD Modulo 0x8 32 read-write 0 0xFFFFFFFF MOD Modulo Value 0 16 read-write 8 0x8 0,1,2,3,4,5,6,7 C%sSC Channel (n) Status And Control 0xC 32 read-write 0 0xFFFFFFFF DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 ELSA Channel (n) Edge or Level Select 2 1 read-write ELSB Channel (n) Edge or Level Select 3 1 read-write MSA Channel (n) Mode Select 4 1 read-write MSB Channel (n) Mode Select 5 1 read-write CHIE Channel (n) Interrupt Enable 6 1 read-write 0 Disable channel (n) interrupt. Use software polling. #0 1 Enable channel (n) interrupt. #1 CHF Channel (n) Flag 7 1 read-only 0 No channel (n) event has occurred. #0 1 A channel (n) event has occurred. #1 TRIGMODE Trigger mode control 8 1 read-write 0 Channel outputs will generate the normal PWM outputs without generating a pulse. #0 1 If a match in the channel occurs, a trigger generation on channel output will happen. The trigger pulse width has one FTM clock cycle. #1 CHIS Channel (n) Input State 9 1 read-only 0 The channel (n) input is zero. #0 1 The channel (n) input is one. #1 8 0x8 0,1,2,3,4,5,6,7 C%sV Channel (n) Value 0x10 32 read-write 0 0xFFFFFFFF VAL Channel Value 0 16 read-write CNTIN Counter Initial Value 0x4C 32 read-write 0 0xFFFFFFFF INIT Initial Value Of The FTM Counter 0 16 read-write STATUS Capture And Compare Status 0x50 32 read-write 0 0xFFFFFFFF CH0F Channel 0 Flag 0 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH1F Channel 1 Flag 1 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH2F Channel 2 Flag 2 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH3F Channel 3 Flag 3 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH4F Channel 4 Flag 4 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH5F Channel 5 Flag 5 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH6F Channel 6 Flag 6 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH7F Channel 7 Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 MODE Features Mode Selection 0x54 32 read-write 0x4 0xFFFFFFFF FTMEN FTM Enable 0 1 read-write 0 TPM compatibility. Free running counter and synchronization compatible with TPM. #0 1 Free running counter and synchronization are different from TPM behavior. #1 INIT Initialize The Channels Output 1 1 read-write WPDIS Write Protection Disable 2 1 read-write 0 Write protection is enabled. #0 1 Write protection is disabled. #1 PWMSYNC PWM Synchronization Mode 3 1 read-write 0 No restrictions. Software and hardware triggers can be used by MOD, CnV, OUTMASK, and FTM counter synchronization. #0 1 Software trigger can only be used by MOD and CnV synchronization, and hardware triggers can only be used by OUTMASK and FTM counter synchronization. #1 CAPTEST Capture Test Mode Enable 4 1 read-write 0 Capture test mode is disabled. #0 1 Capture test mode is enabled. #1 FAULTM Fault Control Mode 5 2 read-write 00 Fault control is disabled for all channels. #00 01 Fault control is enabled for even channels only (channels 0, 2, 4, and 6), and the selected mode is the manual fault clearing. #01 10 Fault control is enabled for all channels, and the selected mode is the manual fault clearing. #10 11 Fault control is enabled for all channels, and the selected mode is the automatic fault clearing. #11 FAULTIE Fault Interrupt Enable 7 1 read-write 0 Fault control interrupt is disabled. #0 1 Fault control interrupt is enabled. #1 SYNC Synchronization 0x58 32 read-write 0 0xFFFFFFFF CNTMIN Minimum Loading Point Enable 0 1 read-write 0 The minimum loading point is disabled. #0 1 The minimum loading point is enabled. #1 CNTMAX Maximum Loading Point Enable 1 1 read-write 0 The maximum loading point is disabled. #0 1 The maximum loading point is enabled. #1 REINIT FTM Counter Reinitialization By Synchronization (FTM counter synchronization) 2 1 read-write 0 FTM counter continues to count normally. #0 1 FTM counter is updated with its initial value when the selected trigger is detected. #1 SYNCHOM Output Mask Synchronization 3 1 read-write 0 OUTMASK register is updated with the value of its buffer in all rising edges of the system clock. #0 1 OUTMASK register is updated with the value of its buffer only by the PWM synchronization. #1 TRIG0 PWM Synchronization Hardware Trigger 0 4 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 TRIG1 PWM Synchronization Hardware Trigger 1 5 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 TRIG2 PWM Synchronization Hardware Trigger 2 6 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 SWSYNC PWM Synchronization Software Trigger 7 1 read-write 0 Software trigger is not selected. #0 1 Software trigger is selected. #1 OUTINIT Initial State For Channels Output 0x5C 32 read-write 0 0xFFFFFFFF CH0OI Channel 0 Output Initialization Value 0 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH1OI Channel 1 Output Initialization Value 1 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH2OI Channel 2 Output Initialization Value 2 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH3OI Channel 3 Output Initialization Value 3 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH4OI Channel 4 Output Initialization Value 4 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH5OI Channel 5 Output Initialization Value 5 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH6OI Channel 6 Output Initialization Value 6 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH7OI Channel 7 Output Initialization Value 7 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 OUTMASK Output Mask 0x60 32 read-write 0 0xFFFFFFFF CH0OM Channel 0 Output Mask 0 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH1OM Channel 1 Output Mask 1 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH2OM Channel 2 Output Mask 2 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH3OM Channel 3 Output Mask 3 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH4OM Channel 4 Output Mask 4 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH5OM Channel 5 Output Mask 5 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH6OM Channel 6 Output Mask 6 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH7OM Channel 7 Output Mask 7 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 COMBINE Function For Linked Channels 0x64 32 read-write 0 0xFFFFFFFF COMBINE0 Combine Channels For n = 0 0 1 read-write COMP0 Complement Of Channel (n) For n = 0 1 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAPEN0 Dual Edge Capture Mode Enable For n = 0 2 1 read-write DECAP0 Dual Edge Capture Mode Captures For n = 0 3 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DTEN0 Deadtime Enable For n = 0 4 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 SYNCEN0 Synchronization Enable For n = 0 5 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 FAULTEN0 Fault Control Enable For n = 0 6 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 COMBINE1 Combine Channels For n = 2 8 1 read-write COMP1 Complement Of Channel (n) For n = 2 9 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAPEN1 Dual Edge Capture Mode Enable For n = 2 10 1 read-write DECAP1 Dual Edge Capture Mode Captures For n = 2 11 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DTEN1 Deadtime Enable For n = 2 12 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 SYNCEN1 Synchronization Enable For n = 2 13 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 FAULTEN1 Fault Control Enable For n = 2 14 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 COMBINE2 Combine Channels For n = 4 16 1 read-write COMP2 Complement Of Channel (n) For n = 4 17 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAPEN2 Dual Edge Capture Mode Enable For n = 4 18 1 read-write DECAP2 Dual Edge Capture Mode Captures For n = 4 19 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DTEN2 Deadtime Enable For n = 4 20 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 SYNCEN2 Synchronization Enable For n = 4 21 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 FAULTEN2 Fault Control Enable For n = 4 22 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 COMBINE3 Combine Channels For n = 6 24 1 read-write COMP3 Complement Of Channel (n) for n = 6 25 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAPEN3 Dual Edge Capture Mode Enable For n = 6 26 1 read-write DECAP3 Dual Edge Capture Mode Captures For n = 6 27 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DTEN3 Deadtime Enable For n = 6 28 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 SYNCEN3 Synchronization Enable For n = 6 29 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 FAULTEN3 Fault Control Enable For n = 6 30 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 DEADTIME Deadtime Insertion Control 0x68 32 read-write 0 0xFFFFFFFF DTVAL Deadtime Value 0 6 read-write DTPS Deadtime Prescaler Value 6 2 read-write 0x Divide the system clock by 1. #0x 10 Divide the system clock by 4. #10 11 Divide the system clock by 16. #11 EXTTRIG FTM External Trigger 0x6C 32 read-write 0 0xFFFFFFFF CH2TRIG Channel 2 Trigger Enable 0 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH3TRIG Channel 3 Trigger Enable 1 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH4TRIG Channel 4 Trigger Enable 2 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH5TRIG Channel 5 Trigger Enable 3 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH0TRIG Channel 0 Trigger Enable 4 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH1TRIG Channel 1 Trigger Enable 5 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 INITTRIGEN Initialization Trigger Enable 6 1 read-write 0 The generation of initialization trigger is disabled. #0 1 The generation of initialization trigger is enabled. #1 TRIGF Channel Trigger Flag 7 1 read-only 0 No channel trigger was generated. #0 1 A channel trigger was generated. #1 CH6TRIG Channel 6 Trigger Enable 8 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH7TRIG Channel 7 Trigger Enable 9 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 POL Channels Polarity 0x70 32 read-write 0 0xFFFFFFFF POL0 Channel 0 Polarity 0 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL1 Channel 1 Polarity 1 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL2 Channel 2 Polarity 2 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL3 Channel 3 Polarity 3 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL4 Channel 4 Polarity 4 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL5 Channel 5 Polarity 5 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL6 Channel 6 Polarity 6 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL7 Channel 7 Polarity 7 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 FMS Fault Mode Status 0x74 32 read-write 0 0xFFFFFFFF FAULTF0 Fault Detection Flag 0 0 1 read-only 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF1 Fault Detection Flag 1 1 1 read-only 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF2 Fault Detection Flag 2 2 1 read-only 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF3 Fault Detection Flag 3 3 1 read-only 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTIN Fault Inputs 5 1 read-only 0 The logic OR of the enabled fault inputs is 0. #0 1 The logic OR of the enabled fault inputs is 1. #1 WPEN Write Protection Enable 6 1 read-write 0 Write protection is disabled. Write protected bits can be written. #0 1 Write protection is enabled. Write protected bits cannot be written. #1 FAULTF Fault Detection Flag 7 1 read-only 0 No fault condition was detected. #0 1 A fault condition was detected. #1 FILTER Input Capture Filter Control 0x78 32 read-write 0 0xFFFFFFFF CH0FVAL Channel 0 Input Filter 0 4 read-write CH1FVAL Channel 1 Input Filter 4 4 read-write CH2FVAL Channel 2 Input Filter 8 4 read-write CH3FVAL Channel 3 Input Filter 12 4 read-write FLTCTRL Fault Control 0x7C 32 read-write 0 0xFFFFFFFF FAULT0EN Fault Input 0 Enable 0 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT1EN Fault Input 1 Enable 1 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT2EN Fault Input 2 Enable 2 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT3EN Fault Input 3 Enable 3 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FFLTR0EN Fault Input 0 Filter Enable 4 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR1EN Fault Input 1 Filter Enable 5 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR2EN Fault Input 2 Filter Enable 6 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR3EN Fault Input 3 Filter Enable 7 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFVAL Fault Input Filter 8 4 read-write FSTATE Fault output state 15 1 read-write 0 FTM outputs will be placed into safe values when fault events in ongoing (defined by POL bits). #0 1 FTM outputs will be tri-stated when fault event is ongoing #1 QDCTRL Quadrature Decoder Control And Status 0x80 32 read-write 0 0xFFFFFFFF QUADEN Quadrature Decoder Mode Enable 0 1 read-write 0 Quadrature Decoder mode is disabled. #0 1 Quadrature Decoder mode is enabled. #1 TOFDIR Timer Overflow Direction In Quadrature Decoder Mode 1 1 read-only 0 TOF bit was set on the bottom of counting. There was an FTM counter decrement and FTM counter changes from its minimum value (CNTIN register) to its maximum value (MOD register). #0 1 TOF bit was set on the top of counting. There was an FTM counter increment and FTM counter changes from its maximum value (MOD register) to its minimum value (CNTIN register). #1 QUADIR FTM Counter Direction In Quadrature Decoder Mode 2 1 read-only 0 Counting direction is decreasing (FTM counter decrement). #0 1 Counting direction is increasing (FTM counter increment). #1 QUADMODE Quadrature Decoder Mode 3 1 read-write 0 Phase A and phase B encoding mode. #0 1 Count and direction encoding mode. #1 PHBPOL Phase B Input Polarity 4 1 read-write 0 Normal polarity. Phase B input signal is not inverted before identifying the rising and falling edges of this signal. #0 1 Inverted polarity. Phase B input signal is inverted before identifying the rising and falling edges of this signal. #1 PHAPOL Phase A Input Polarity 5 1 read-write 0 Normal polarity. Phase A input signal is not inverted before identifying the rising and falling edges of this signal. #0 1 Inverted polarity. Phase A input signal is inverted before identifying the rising and falling edges of this signal. #1 PHBFLTREN Phase B Input Filter Enable 6 1 read-write 0 Phase B input filter is disabled. #0 1 Phase B input filter is enabled. #1 PHAFLTREN Phase A Input Filter Enable 7 1 read-write 0 Phase A input filter is disabled. #0 1 Phase A input filter is enabled. #1 CONF Configuration 0x84 32 read-write 0 0xFFFFFFFF LDFQ Load Frequency 0 5 read-write BDMMODE Debug Mode 6 2 read-write GTBEEN Global Time Base Enable 9 1 read-write 0 Use of an external global time base is disabled. #0 1 Use of an external global time base is enabled. #1 GTBEOUT Global Time Base Output 10 1 read-write 0 A global time base signal generation is disabled. #0 1 A global time base signal generation is enabled. #1 ITRIGR Initialization trigger on Reload Point 11 1 read-write 0 Initialization trigger is generated on counter wrap events. #0 1 Initialization trigger is generated when a reload point is reached. #1 FLTPOL FTM Fault Input Polarity 0x88 32 read-write 0 0xFFFFFFFF FLT0POL Fault Input 0 Polarity 0 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT1POL Fault Input 1 Polarity 1 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT2POL Fault Input 2 Polarity 2 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT3POL Fault Input 3 Polarity 3 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 SYNCONF Synchronization Configuration 0x8C 32 read-write 0 0xFFFFFFFF HWTRIGMODE Hardware Trigger Mode 0 1 read-write 0 FTM clears the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2. #0 1 FTM does not clear the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2. #1 CNTINC CNTIN Register Synchronization 2 1 read-write 0 CNTIN register is updated with its buffer value at all rising edges of system clock. #0 1 CNTIN register is updated with its buffer value by the PWM synchronization. #1 INVC INVCTRL Register Synchronization 4 1 read-write 0 INVCTRL register is updated with its buffer value at all rising edges of system clock. #0 1 INVCTRL register is updated with its buffer value by the PWM synchronization. #1 SWOC SWOCTRL Register Synchronization 5 1 read-write 0 SWOCTRL register is updated with its buffer value at all rising edges of system clock. #0 1 SWOCTRL register is updated with its buffer value by the PWM synchronization. #1 SYNCMODE Synchronization Mode 7 1 read-write 0 Legacy PWM synchronization is selected. #0 1 Enhanced PWM synchronization is selected. #1 SWRSTCNT FTM counter synchronization is activated by the software trigger. 8 1 read-write 0 The software trigger does not activate the FTM counter synchronization. #0 1 The software trigger activates the FTM counter synchronization. #1 SWWRBUF MOD, HCR, CNTIN, and CV registers synchronization is activated by the software trigger. 9 1 read-write 0 The software trigger does not activate MOD, HCR, CNTIN, and CV registers synchronization. #0 1 The software trigger activates MOD, HCR, CNTIN, and CV registers synchronization. #1 SWOM Output mask synchronization is activated by the software trigger. 10 1 read-write 0 The software trigger does not activate the OUTMASK register synchronization. #0 1 The software trigger activates the OUTMASK register synchronization. #1 SWINVC Inverting control synchronization is activated by the software trigger. 11 1 read-write 0 The software trigger does not activate the INVCTRL register synchronization. #0 1 The software trigger activates the INVCTRL register synchronization. #1 SWSOC Software output control synchronization is activated by the software trigger. 12 1 read-write 0 The software trigger does not activate the SWOCTRL register synchronization. #0 1 The software trigger activates the SWOCTRL register synchronization. #1 HWRSTCNT FTM counter synchronization is activated by a hardware trigger. 16 1 read-write 0 A hardware trigger does not activate the FTM counter synchronization. #0 1 A hardware trigger activates the FTM counter synchronization. #1 HWWRBUF MOD, HCR, CNTIN, and CV registers synchronization is activated by a hardware trigger. 17 1 read-write 0 A hardware trigger does not activate MOD, HCR, CNTIN, and CV registers synchronization. #0 1 A hardware trigger activates MOD, HCR, CNTIN, and CV registers synchronization. #1 HWOM Output mask synchronization is activated by a hardware trigger. 18 1 read-write 0 A hardware trigger does not activate the OUTMASK register synchronization. #0 1 A hardware trigger activates the OUTMASK register synchronization. #1 HWINVC Inverting control synchronization is activated by a hardware trigger. 19 1 read-write 0 A hardware trigger does not activate the INVCTRL register synchronization. #0 1 A hardware trigger activates the INVCTRL register synchronization. #1 HWSOC Software output control synchronization is activated by a hardware trigger. 20 1 read-write 0 A hardware trigger does not activate the SWOCTRL register synchronization. #0 1 A hardware trigger activates the SWOCTRL register synchronization. #1 INVCTRL FTM Inverting Control 0x90 32 read-write 0 0xFFFFFFFF INV0EN Pair Channels 0 Inverting Enable 0 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV1EN Pair Channels 1 Inverting Enable 1 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV2EN Pair Channels 2 Inverting Enable 2 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV3EN Pair Channels 3 Inverting Enable 3 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 SWOCTRL FTM Software Output Control 0x94 32 read-write 0 0xFFFFFFFF CH0OC Channel 0 Software Output Control Enable 0 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH1OC Channel 1 Software Output Control Enable 1 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH2OC Channel 2 Software Output Control Enable 2 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH3OC Channel 3 Software Output Control Enable 3 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH4OC Channel 4 Software Output Control Enable 4 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH5OC Channel 5 Software Output Control Enable 5 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH6OC Channel 6 Software Output Control Enable 6 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH7OC Channel 7 Software Output Control Enable 7 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH0OCV Channel 0 Software Output Control Value 8 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH1OCV Channel 1 Software Output Control Value 9 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH2OCV Channel 2 Software Output Control Value 10 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH3OCV Channel 3 Software Output Control Value 11 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH4OCV Channel 4 Software Output Control Value 12 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH5OCV Channel 5 Software Output Control Value 13 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH6OCV Channel 6 Software Output Control Value 14 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH7OCV Channel 7 Software Output Control Value 15 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 PWMLOAD FTM PWM Load 0x98 32 read-write 0 0xFFFFFFFF CH0SEL Channel 0 Select 0 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH1SEL Channel 1 Select 1 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH2SEL Channel 2 Select 2 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH3SEL Channel 3 Select 3 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH4SEL Channel 4 Select 4 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH5SEL Channel 5 Select 5 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH6SEL Channel 6 Select 6 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH7SEL Channel 7 Select 7 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 HCSEL Half Cycle Select 8 1 read-write 0 Half cycle reload is disabled and it is not considered as a reload opportunity. #0 1 Half cycle reload is enabled and it is considered as a reload opportunity. #1 LDOK Load Enable 9 1 read-write 0 Loading updated values is disabled. #0 1 Loading updated values is enabled. #1 GLEN Global Load Enable 10 1 read-write 0 Global Load Ok disabled. #0 1 Global Load OK enabled. A pulse event on the module global load input sets the LDOK bit. #1 GLDOK Global Load OK 11 1 write-only 0 No action. #0 1 LDOK bit is set. #1 HCR Half Cycle Register 0x9C 32 read-write 0 0xFFFFFFFF HCVAL Half Cycle Value 0 16 read-write MOD_MIRROR Modulo 0x200 32 read-write 0 0xFFFFFFFF FRACMOD Fractional Value for MOD register 11 5 read-write MOD Modulo Value 16 16 read-write 8 0x4 0,1,2,3,4,5,6,7 C%sV_MIRROR Channel (n) Value 0x204 32 read-write 0 0xFFFFFFFF FRACVAL Fractional Value for VAL register 11 5 read-write VAL Channel Value 16 16 read-write FTM1 FlexTimer Module FTM FTM1_ 0x40039000 0 0x224 registers FTM1 18 SC Status And Control 0 32 read-write 0 0xFFFFFFFF PS Prescale Factor Selection 0 3 read-write 000 Divide by 1 #000 001 Divide by 2 #001 010 Divide by 4 #010 011 Divide by 8 #011 100 Divide by 16 #100 101 Divide by 32 #101 110 Divide by 64 #110 111 Divide by 128 #111 CLKS Clock Source Selection 3 2 read-write 00 No clock selected. This in effect disables the FTM counter. #00 01 System clock #01 10 Fixed frequency clock #10 11 External clock #11 CPWMS Center-Aligned PWM Select 5 1 read-write 0 FTM counter operates in Up Counting mode. #0 1 FTM counter operates in Up-Down Counting mode. #1 RIE Reload Interrupt Enable 6 1 read-write 0 Reload interrupt is disabled. #0 1 Reload interrupt is enabled. #1 RF Reload Flag 7 1 read-only 0 FTM counter did not reach a reload point. #0 1 FTM counter reached a reload point. #1 TOIE Timer Overflow Interrupt Enable 8 1 read-write 0 Disable TOF interrupts. Use software polling. #0 1 Enable TOF interrupts. An interrupt is generated when TOF equals one. #1 TOF Timer Overflow Flag 9 1 read-only 0 FTM counter has not overflowed. #0 1 FTM counter has overflowed. #1 PWMEN0 Channel 0 PWM enable bit 16 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN1 Channel 1 PWM enable bit 17 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN2 Channel 2 PWM enable bit 18 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN3 Channel 3 PWM enable bit 19 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN4 Channel 4 PWM enable bit 20 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN5 Channel 5 PWM enable bit 21 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN6 Channel 6 PWM enable bit 22 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN7 Channel 7 PWM enable bit 23 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 CNT Counter 0x4 32 read-write 0 0xFFFFFFFF COUNT Counter Value 0 16 read-write MOD Modulo 0x8 32 read-write 0 0xFFFFFFFF MOD Modulo Value 0 16 read-write 4 0x8 0,1,2,3 C%sSC Channel (n) Status And Control 0xC 32 read-write 0 0xFFFFFFFF DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 ELSA Channel (n) Edge or Level Select 2 1 read-write ELSB Channel (n) Edge or Level Select 3 1 read-write MSA Channel (n) Mode Select 4 1 read-write MSB Channel (n) Mode Select 5 1 read-write CHIE Channel (n) Interrupt Enable 6 1 read-write 0 Disable channel (n) interrupt. Use software polling. #0 1 Enable channel (n) interrupt. #1 CHF Channel (n) Flag 7 1 read-only 0 No channel (n) event has occurred. #0 1 A channel (n) event has occurred. #1 TRIGMODE Trigger mode control 8 1 read-write 0 Channel outputs will generate the normal PWM outputs without generating a pulse. #0 1 If a match in the channel occurs, a trigger generation on channel output will happen. The trigger pulse width has one FTM clock cycle. #1 CHIS Channel (n) Input State 9 1 read-only 0 The channel (n) input is zero. #0 1 The channel (n) input is one. #1 4 0x8 0,1,2,3 C%sV Channel (n) Value 0x10 32 read-write 0 0xFFFFFFFF VAL Channel Value 0 16 read-write CNTIN Counter Initial Value 0x4C 32 read-write 0 0xFFFFFFFF INIT Initial Value Of The FTM Counter 0 16 read-write STATUS Capture And Compare Status 0x50 32 read-write 0 0xFFFFFFFF CH0F Channel 0 Flag 0 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH1F Channel 1 Flag 1 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH2F Channel 2 Flag 2 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH3F Channel 3 Flag 3 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH4F Channel 4 Flag 4 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH5F Channel 5 Flag 5 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH6F Channel 6 Flag 6 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH7F Channel 7 Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 MODE Features Mode Selection 0x54 32 read-write 0x4 0xFFFFFFFF FTMEN FTM Enable 0 1 read-write 0 TPM compatibility. Free running counter and synchronization compatible with TPM. #0 1 Free running counter and synchronization are different from TPM behavior. #1 INIT Initialize The Channels Output 1 1 read-write WPDIS Write Protection Disable 2 1 read-write 0 Write protection is enabled. #0 1 Write protection is disabled. #1 PWMSYNC PWM Synchronization Mode 3 1 read-write 0 No restrictions. Software and hardware triggers can be used by MOD, CnV, OUTMASK, and FTM counter synchronization. #0 1 Software trigger can only be used by MOD and CnV synchronization, and hardware triggers can only be used by OUTMASK and FTM counter synchronization. #1 CAPTEST Capture Test Mode Enable 4 1 read-write 0 Capture test mode is disabled. #0 1 Capture test mode is enabled. #1 FAULTM Fault Control Mode 5 2 read-write 00 Fault control is disabled for all channels. #00 01 Fault control is enabled for even channels only (channels 0, 2, 4, and 6), and the selected mode is the manual fault clearing. #01 10 Fault control is enabled for all channels, and the selected mode is the manual fault clearing. #10 11 Fault control is enabled for all channels, and the selected mode is the automatic fault clearing. #11 FAULTIE Fault Interrupt Enable 7 1 read-write 0 Fault control interrupt is disabled. #0 1 Fault control interrupt is enabled. #1 SYNC Synchronization 0x58 32 read-write 0 0xFFFFFFFF CNTMIN Minimum Loading Point Enable 0 1 read-write 0 The minimum loading point is disabled. #0 1 The minimum loading point is enabled. #1 CNTMAX Maximum Loading Point Enable 1 1 read-write 0 The maximum loading point is disabled. #0 1 The maximum loading point is enabled. #1 REINIT FTM Counter Reinitialization By Synchronization (FTM counter synchronization) 2 1 read-write 0 FTM counter continues to count normally. #0 1 FTM counter is updated with its initial value when the selected trigger is detected. #1 SYNCHOM Output Mask Synchronization 3 1 read-write 0 OUTMASK register is updated with the value of its buffer in all rising edges of the system clock. #0 1 OUTMASK register is updated with the value of its buffer only by the PWM synchronization. #1 TRIG0 PWM Synchronization Hardware Trigger 0 4 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 TRIG1 PWM Synchronization Hardware Trigger 1 5 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 TRIG2 PWM Synchronization Hardware Trigger 2 6 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 SWSYNC PWM Synchronization Software Trigger 7 1 read-write 0 Software trigger is not selected. #0 1 Software trigger is selected. #1 OUTINIT Initial State For Channels Output 0x5C 32 read-write 0 0xFFFFFFFF CH0OI Channel 0 Output Initialization Value 0 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH1OI Channel 1 Output Initialization Value 1 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH2OI Channel 2 Output Initialization Value 2 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH3OI Channel 3 Output Initialization Value 3 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH4OI Channel 4 Output Initialization Value 4 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH5OI Channel 5 Output Initialization Value 5 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH6OI Channel 6 Output Initialization Value 6 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH7OI Channel 7 Output Initialization Value 7 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 OUTMASK Output Mask 0x60 32 read-write 0 0xFFFFFFFF CH0OM Channel 0 Output Mask 0 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH1OM Channel 1 Output Mask 1 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH2OM Channel 2 Output Mask 2 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH3OM Channel 3 Output Mask 3 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH4OM Channel 4 Output Mask 4 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH5OM Channel 5 Output Mask 5 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH6OM Channel 6 Output Mask 6 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH7OM Channel 7 Output Mask 7 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 COMBINE Function For Linked Channels 0x64 32 read-write 0 0xFFFFFFFF COMBINE0 Combine Channels For n = 0 0 1 read-write COMP0 Complement Of Channel (n) For n = 0 1 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAPEN0 Dual Edge Capture Mode Enable For n = 0 2 1 read-write DECAP0 Dual Edge Capture Mode Captures For n = 0 3 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DTEN0 Deadtime Enable For n = 0 4 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 SYNCEN0 Synchronization Enable For n = 0 5 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 FAULTEN0 Fault Control Enable For n = 0 6 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 COMBINE1 Combine Channels For n = 2 8 1 read-write COMP1 Complement Of Channel (n) For n = 2 9 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAPEN1 Dual Edge Capture Mode Enable For n = 2 10 1 read-write DECAP1 Dual Edge Capture Mode Captures For n = 2 11 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DTEN1 Deadtime Enable For n = 2 12 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 SYNCEN1 Synchronization Enable For n = 2 13 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 FAULTEN1 Fault Control Enable For n = 2 14 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 COMBINE2 Combine Channels For n = 4 16 1 read-write COMP2 Complement Of Channel (n) For n = 4 17 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAPEN2 Dual Edge Capture Mode Enable For n = 4 18 1 read-write DECAP2 Dual Edge Capture Mode Captures For n = 4 19 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DTEN2 Deadtime Enable For n = 4 20 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 SYNCEN2 Synchronization Enable For n = 4 21 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 FAULTEN2 Fault Control Enable For n = 4 22 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 COMBINE3 Combine Channels For n = 6 24 1 read-write COMP3 Complement Of Channel (n) for n = 6 25 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAPEN3 Dual Edge Capture Mode Enable For n = 6 26 1 read-write DECAP3 Dual Edge Capture Mode Captures For n = 6 27 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DTEN3 Deadtime Enable For n = 6 28 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 SYNCEN3 Synchronization Enable For n = 6 29 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 FAULTEN3 Fault Control Enable For n = 6 30 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 DEADTIME Deadtime Insertion Control 0x68 32 read-write 0 0xFFFFFFFF DTVAL Deadtime Value 0 6 read-write DTPS Deadtime Prescaler Value 6 2 read-write 0x Divide the system clock by 1. #0x 10 Divide the system clock by 4. #10 11 Divide the system clock by 16. #11 EXTTRIG FTM External Trigger 0x6C 32 read-write 0 0xFFFFFFFF CH2TRIG Channel 2 Trigger Enable 0 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH3TRIG Channel 3 Trigger Enable 1 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH4TRIG Channel 4 Trigger Enable 2 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH5TRIG Channel 5 Trigger Enable 3 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH0TRIG Channel 0 Trigger Enable 4 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH1TRIG Channel 1 Trigger Enable 5 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 INITTRIGEN Initialization Trigger Enable 6 1 read-write 0 The generation of initialization trigger is disabled. #0 1 The generation of initialization trigger is enabled. #1 TRIGF Channel Trigger Flag 7 1 read-only 0 No channel trigger was generated. #0 1 A channel trigger was generated. #1 CH6TRIG Channel 6 Trigger Enable 8 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH7TRIG Channel 7 Trigger Enable 9 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 POL Channels Polarity 0x70 32 read-write 0 0xFFFFFFFF POL0 Channel 0 Polarity 0 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL1 Channel 1 Polarity 1 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL2 Channel 2 Polarity 2 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL3 Channel 3 Polarity 3 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL4 Channel 4 Polarity 4 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL5 Channel 5 Polarity 5 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL6 Channel 6 Polarity 6 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL7 Channel 7 Polarity 7 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 FMS Fault Mode Status 0x74 32 read-write 0 0xFFFFFFFF FAULTF0 Fault Detection Flag 0 0 1 read-only 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF1 Fault Detection Flag 1 1 1 read-only 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF2 Fault Detection Flag 2 2 1 read-only 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF3 Fault Detection Flag 3 3 1 read-only 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTIN Fault Inputs 5 1 read-only 0 The logic OR of the enabled fault inputs is 0. #0 1 The logic OR of the enabled fault inputs is 1. #1 WPEN Write Protection Enable 6 1 read-write 0 Write protection is disabled. Write protected bits can be written. #0 1 Write protection is enabled. Write protected bits cannot be written. #1 FAULTF Fault Detection Flag 7 1 read-only 0 No fault condition was detected. #0 1 A fault condition was detected. #1 FILTER Input Capture Filter Control 0x78 32 read-write 0 0xFFFFFFFF CH0FVAL Channel 0 Input Filter 0 4 read-write CH1FVAL Channel 1 Input Filter 4 4 read-write CH2FVAL Channel 2 Input Filter 8 4 read-write CH3FVAL Channel 3 Input Filter 12 4 read-write FLTCTRL Fault Control 0x7C 32 read-write 0 0xFFFFFFFF FAULT0EN Fault Input 0 Enable 0 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT1EN Fault Input 1 Enable 1 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT2EN Fault Input 2 Enable 2 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT3EN Fault Input 3 Enable 3 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FFLTR0EN Fault Input 0 Filter Enable 4 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR1EN Fault Input 1 Filter Enable 5 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR2EN Fault Input 2 Filter Enable 6 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR3EN Fault Input 3 Filter Enable 7 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFVAL Fault Input Filter 8 4 read-write FSTATE Fault output state 15 1 read-write 0 FTM outputs will be placed into safe values when fault events in ongoing (defined by POL bits). #0 1 FTM outputs will be tri-stated when fault event is ongoing #1 QDCTRL Quadrature Decoder Control And Status 0x80 32 read-write 0 0xFFFFFFFF QUADEN Quadrature Decoder Mode Enable 0 1 read-write 0 Quadrature Decoder mode is disabled. #0 1 Quadrature Decoder mode is enabled. #1 TOFDIR Timer Overflow Direction In Quadrature Decoder Mode 1 1 read-only 0 TOF bit was set on the bottom of counting. There was an FTM counter decrement and FTM counter changes from its minimum value (CNTIN register) to its maximum value (MOD register). #0 1 TOF bit was set on the top of counting. There was an FTM counter increment and FTM counter changes from its maximum value (MOD register) to its minimum value (CNTIN register). #1 QUADIR FTM Counter Direction In Quadrature Decoder Mode 2 1 read-only 0 Counting direction is decreasing (FTM counter decrement). #0 1 Counting direction is increasing (FTM counter increment). #1 QUADMODE Quadrature Decoder Mode 3 1 read-write 0 Phase A and phase B encoding mode. #0 1 Count and direction encoding mode. #1 PHBPOL Phase B Input Polarity 4 1 read-write 0 Normal polarity. Phase B input signal is not inverted before identifying the rising and falling edges of this signal. #0 1 Inverted polarity. Phase B input signal is inverted before identifying the rising and falling edges of this signal. #1 PHAPOL Phase A Input Polarity 5 1 read-write 0 Normal polarity. Phase A input signal is not inverted before identifying the rising and falling edges of this signal. #0 1 Inverted polarity. Phase A input signal is inverted before identifying the rising and falling edges of this signal. #1 PHBFLTREN Phase B Input Filter Enable 6 1 read-write 0 Phase B input filter is disabled. #0 1 Phase B input filter is enabled. #1 PHAFLTREN Phase A Input Filter Enable 7 1 read-write 0 Phase A input filter is disabled. #0 1 Phase A input filter is enabled. #1 CONF Configuration 0x84 32 read-write 0 0xFFFFFFFF LDFQ Load Frequency 0 5 read-write BDMMODE Debug Mode 6 2 read-write GTBEEN Global Time Base Enable 9 1 read-write 0 Use of an external global time base is disabled. #0 1 Use of an external global time base is enabled. #1 GTBEOUT Global Time Base Output 10 1 read-write 0 A global time base signal generation is disabled. #0 1 A global time base signal generation is enabled. #1 ITRIGR Initialization trigger on Reload Point 11 1 read-write 0 Initialization trigger is generated on counter wrap events. #0 1 Initialization trigger is generated when a reload point is reached. #1 FLTPOL FTM Fault Input Polarity 0x88 32 read-write 0 0xFFFFFFFF FLT0POL Fault Input 0 Polarity 0 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT1POL Fault Input 1 Polarity 1 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT2POL Fault Input 2 Polarity 2 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT3POL Fault Input 3 Polarity 3 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 SYNCONF Synchronization Configuration 0x8C 32 read-write 0 0xFFFFFFFF HWTRIGMODE Hardware Trigger Mode 0 1 read-write 0 FTM clears the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2. #0 1 FTM does not clear the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2. #1 CNTINC CNTIN Register Synchronization 2 1 read-write 0 CNTIN register is updated with its buffer value at all rising edges of system clock. #0 1 CNTIN register is updated with its buffer value by the PWM synchronization. #1 INVC INVCTRL Register Synchronization 4 1 read-write 0 INVCTRL register is updated with its buffer value at all rising edges of system clock. #0 1 INVCTRL register is updated with its buffer value by the PWM synchronization. #1 SWOC SWOCTRL Register Synchronization 5 1 read-write 0 SWOCTRL register is updated with its buffer value at all rising edges of system clock. #0 1 SWOCTRL register is updated with its buffer value by the PWM synchronization. #1 SYNCMODE Synchronization Mode 7 1 read-write 0 Legacy PWM synchronization is selected. #0 1 Enhanced PWM synchronization is selected. #1 SWRSTCNT FTM counter synchronization is activated by the software trigger. 8 1 read-write 0 The software trigger does not activate the FTM counter synchronization. #0 1 The software trigger activates the FTM counter synchronization. #1 SWWRBUF MOD, HCR, CNTIN, and CV registers synchronization is activated by the software trigger. 9 1 read-write 0 The software trigger does not activate MOD, HCR, CNTIN, and CV registers synchronization. #0 1 The software trigger activates MOD, HCR, CNTIN, and CV registers synchronization. #1 SWOM Output mask synchronization is activated by the software trigger. 10 1 read-write 0 The software trigger does not activate the OUTMASK register synchronization. #0 1 The software trigger activates the OUTMASK register synchronization. #1 SWINVC Inverting control synchronization is activated by the software trigger. 11 1 read-write 0 The software trigger does not activate the INVCTRL register synchronization. #0 1 The software trigger activates the INVCTRL register synchronization. #1 SWSOC Software output control synchronization is activated by the software trigger. 12 1 read-write 0 The software trigger does not activate the SWOCTRL register synchronization. #0 1 The software trigger activates the SWOCTRL register synchronization. #1 HWRSTCNT FTM counter synchronization is activated by a hardware trigger. 16 1 read-write 0 A hardware trigger does not activate the FTM counter synchronization. #0 1 A hardware trigger activates the FTM counter synchronization. #1 HWWRBUF MOD, HCR, CNTIN, and CV registers synchronization is activated by a hardware trigger. 17 1 read-write 0 A hardware trigger does not activate MOD, HCR, CNTIN, and CV registers synchronization. #0 1 A hardware trigger activates MOD, HCR, CNTIN, and CV registers synchronization. #1 HWOM Output mask synchronization is activated by a hardware trigger. 18 1 read-write 0 A hardware trigger does not activate the OUTMASK register synchronization. #0 1 A hardware trigger activates the OUTMASK register synchronization. #1 HWINVC Inverting control synchronization is activated by a hardware trigger. 19 1 read-write 0 A hardware trigger does not activate the INVCTRL register synchronization. #0 1 A hardware trigger activates the INVCTRL register synchronization. #1 HWSOC Software output control synchronization is activated by a hardware trigger. 20 1 read-write 0 A hardware trigger does not activate the SWOCTRL register synchronization. #0 1 A hardware trigger activates the SWOCTRL register synchronization. #1 INVCTRL FTM Inverting Control 0x90 32 read-write 0 0xFFFFFFFF INV0EN Pair Channels 0 Inverting Enable 0 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV1EN Pair Channels 1 Inverting Enable 1 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV2EN Pair Channels 2 Inverting Enable 2 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV3EN Pair Channels 3 Inverting Enable 3 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 SWOCTRL FTM Software Output Control 0x94 32 read-write 0 0xFFFFFFFF CH0OC Channel 0 Software Output Control Enable 0 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH1OC Channel 1 Software Output Control Enable 1 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH2OC Channel 2 Software Output Control Enable 2 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH3OC Channel 3 Software Output Control Enable 3 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH4OC Channel 4 Software Output Control Enable 4 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH5OC Channel 5 Software Output Control Enable 5 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH6OC Channel 6 Software Output Control Enable 6 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH7OC Channel 7 Software Output Control Enable 7 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH0OCV Channel 0 Software Output Control Value 8 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH1OCV Channel 1 Software Output Control Value 9 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH2OCV Channel 2 Software Output Control Value 10 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH3OCV Channel 3 Software Output Control Value 11 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH4OCV Channel 4 Software Output Control Value 12 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH5OCV Channel 5 Software Output Control Value 13 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH6OCV Channel 6 Software Output Control Value 14 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH7OCV Channel 7 Software Output Control Value 15 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 PWMLOAD FTM PWM Load 0x98 32 read-write 0 0xFFFFFFFF CH0SEL Channel 0 Select 0 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH1SEL Channel 1 Select 1 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH2SEL Channel 2 Select 2 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH3SEL Channel 3 Select 3 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH4SEL Channel 4 Select 4 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH5SEL Channel 5 Select 5 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH6SEL Channel 6 Select 6 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH7SEL Channel 7 Select 7 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 HCSEL Half Cycle Select 8 1 read-write 0 Half cycle reload is disabled and it is not considered as a reload opportunity. #0 1 Half cycle reload is enabled and it is considered as a reload opportunity. #1 LDOK Load Enable 9 1 read-write 0 Loading updated values is disabled. #0 1 Loading updated values is enabled. #1 GLEN Global Load Enable 10 1 read-write 0 Global Load Ok disabled. #0 1 Global Load OK enabled. A pulse event on the module global load input sets the LDOK bit. #1 GLDOK Global Load OK 11 1 write-only 0 No action. #0 1 LDOK bit is set. #1 HCR Half Cycle Register 0x9C 32 read-write 0 0xFFFFFFFF HCVAL Half Cycle Value 0 16 read-write MOD_MIRROR Modulo 0x200 32 read-write 0 0xFFFFFFFF FRACMOD Fractional Value for MOD register 11 5 read-write MOD Modulo Value 16 16 read-write 8 0x4 0,1,2,3,4,5,6,7 C%sV_MIRROR Channel (n) Value 0x204 32 read-write 0 0xFFFFFFFF FRACVAL Fractional Value for VAL register 11 5 read-write VAL Channel Value 16 16 read-write FTM2 FlexTimer Module FTM FTM2_ 0x4003A000 0 0x224 registers FTM2 19 SC Status And Control 0 32 read-write 0 0xFFFFFFFF PS Prescale Factor Selection 0 3 read-write 000 Divide by 1 #000 001 Divide by 2 #001 010 Divide by 4 #010 011 Divide by 8 #011 100 Divide by 16 #100 101 Divide by 32 #101 110 Divide by 64 #110 111 Divide by 128 #111 CLKS Clock Source Selection 3 2 read-write 00 No clock selected. This in effect disables the FTM counter. #00 01 System clock #01 10 Fixed frequency clock #10 11 External clock #11 CPWMS Center-Aligned PWM Select 5 1 read-write 0 FTM counter operates in Up Counting mode. #0 1 FTM counter operates in Up-Down Counting mode. #1 RIE Reload Interrupt Enable 6 1 read-write 0 Reload interrupt is disabled. #0 1 Reload interrupt is enabled. #1 RF Reload Flag 7 1 read-only 0 FTM counter did not reach a reload point. #0 1 FTM counter reached a reload point. #1 TOIE Timer Overflow Interrupt Enable 8 1 read-write 0 Disable TOF interrupts. Use software polling. #0 1 Enable TOF interrupts. An interrupt is generated when TOF equals one. #1 TOF Timer Overflow Flag 9 1 read-only 0 FTM counter has not overflowed. #0 1 FTM counter has overflowed. #1 PWMEN0 Channel 0 PWM enable bit 16 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN1 Channel 1 PWM enable bit 17 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN2 Channel 2 PWM enable bit 18 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN3 Channel 3 PWM enable bit 19 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN4 Channel 4 PWM enable bit 20 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN5 Channel 5 PWM enable bit 21 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN6 Channel 6 PWM enable bit 22 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 PWMEN7 Channel 7 PWM enable bit 23 1 read-write 0 Channel output port is disabled #0 1 Channel output port is enabled #1 CNT Counter 0x4 32 read-write 0 0xFFFFFFFF COUNT Counter Value 0 16 read-write MOD Modulo 0x8 32 read-write 0 0xFFFFFFFF MOD Modulo Value 0 16 read-write 4 0x8 0,1,2,3 C%sSC Channel (n) Status And Control 0xC 32 read-write 0 0xFFFFFFFF DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 ELSA Channel (n) Edge or Level Select 2 1 read-write ELSB Channel (n) Edge or Level Select 3 1 read-write MSA Channel (n) Mode Select 4 1 read-write MSB Channel (n) Mode Select 5 1 read-write CHIE Channel (n) Interrupt Enable 6 1 read-write 0 Disable channel (n) interrupt. Use software polling. #0 1 Enable channel (n) interrupt. #1 CHF Channel (n) Flag 7 1 read-only 0 No channel (n) event has occurred. #0 1 A channel (n) event has occurred. #1 TRIGMODE Trigger mode control 8 1 read-write 0 Channel outputs will generate the normal PWM outputs without generating a pulse. #0 1 If a match in the channel occurs, a trigger generation on channel output will happen. The trigger pulse width has one FTM clock cycle. #1 CHIS Channel (n) Input State 9 1 read-only 0 The channel (n) input is zero. #0 1 The channel (n) input is one. #1 4 0x8 0,1,2,3 C%sV Channel (n) Value 0x10 32 read-write 0 0xFFFFFFFF VAL Channel Value 0 16 read-write CNTIN Counter Initial Value 0x4C 32 read-write 0 0xFFFFFFFF INIT Initial Value Of The FTM Counter 0 16 read-write STATUS Capture And Compare Status 0x50 32 read-write 0 0xFFFFFFFF CH0F Channel 0 Flag 0 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH1F Channel 1 Flag 1 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH2F Channel 2 Flag 2 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH3F Channel 3 Flag 3 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH4F Channel 4 Flag 4 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH5F Channel 5 Flag 5 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH6F Channel 6 Flag 6 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH7F Channel 7 Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 MODE Features Mode Selection 0x54 32 read-write 0x4 0xFFFFFFFF FTMEN FTM Enable 0 1 read-write 0 TPM compatibility. Free running counter and synchronization compatible with TPM. #0 1 Free running counter and synchronization are different from TPM behavior. #1 INIT Initialize The Channels Output 1 1 read-write WPDIS Write Protection Disable 2 1 read-write 0 Write protection is enabled. #0 1 Write protection is disabled. #1 PWMSYNC PWM Synchronization Mode 3 1 read-write 0 No restrictions. Software and hardware triggers can be used by MOD, CnV, OUTMASK, and FTM counter synchronization. #0 1 Software trigger can only be used by MOD and CnV synchronization, and hardware triggers can only be used by OUTMASK and FTM counter synchronization. #1 CAPTEST Capture Test Mode Enable 4 1 read-write 0 Capture test mode is disabled. #0 1 Capture test mode is enabled. #1 FAULTM Fault Control Mode 5 2 read-write 00 Fault control is disabled for all channels. #00 01 Fault control is enabled for even channels only (channels 0, 2, 4, and 6), and the selected mode is the manual fault clearing. #01 10 Fault control is enabled for all channels, and the selected mode is the manual fault clearing. #10 11 Fault control is enabled for all channels, and the selected mode is the automatic fault clearing. #11 FAULTIE Fault Interrupt Enable 7 1 read-write 0 Fault control interrupt is disabled. #0 1 Fault control interrupt is enabled. #1 SYNC Synchronization 0x58 32 read-write 0 0xFFFFFFFF CNTMIN Minimum Loading Point Enable 0 1 read-write 0 The minimum loading point is disabled. #0 1 The minimum loading point is enabled. #1 CNTMAX Maximum Loading Point Enable 1 1 read-write 0 The maximum loading point is disabled. #0 1 The maximum loading point is enabled. #1 REINIT FTM Counter Reinitialization By Synchronization (FTM counter synchronization) 2 1 read-write 0 FTM counter continues to count normally. #0 1 FTM counter is updated with its initial value when the selected trigger is detected. #1 SYNCHOM Output Mask Synchronization 3 1 read-write 0 OUTMASK register is updated with the value of its buffer in all rising edges of the system clock. #0 1 OUTMASK register is updated with the value of its buffer only by the PWM synchronization. #1 TRIG0 PWM Synchronization Hardware Trigger 0 4 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 TRIG1 PWM Synchronization Hardware Trigger 1 5 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 TRIG2 PWM Synchronization Hardware Trigger 2 6 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 SWSYNC PWM Synchronization Software Trigger 7 1 read-write 0 Software trigger is not selected. #0 1 Software trigger is selected. #1 OUTINIT Initial State For Channels Output 0x5C 32 read-write 0 0xFFFFFFFF CH0OI Channel 0 Output Initialization Value 0 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH1OI Channel 1 Output Initialization Value 1 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH2OI Channel 2 Output Initialization Value 2 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH3OI Channel 3 Output Initialization Value 3 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH4OI Channel 4 Output Initialization Value 4 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH5OI Channel 5 Output Initialization Value 5 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH6OI Channel 6 Output Initialization Value 6 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH7OI Channel 7 Output Initialization Value 7 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 OUTMASK Output Mask 0x60 32 read-write 0 0xFFFFFFFF CH0OM Channel 0 Output Mask 0 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH1OM Channel 1 Output Mask 1 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH2OM Channel 2 Output Mask 2 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH3OM Channel 3 Output Mask 3 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH4OM Channel 4 Output Mask 4 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH5OM Channel 5 Output Mask 5 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH6OM Channel 6 Output Mask 6 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH7OM Channel 7 Output Mask 7 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 COMBINE Function For Linked Channels 0x64 32 read-write 0 0xFFFFFFFF COMBINE0 Combine Channels For n = 0 0 1 read-write COMP0 Complement Of Channel (n) For n = 0 1 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAPEN0 Dual Edge Capture Mode Enable For n = 0 2 1 read-write DECAP0 Dual Edge Capture Mode Captures For n = 0 3 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DTEN0 Deadtime Enable For n = 0 4 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 SYNCEN0 Synchronization Enable For n = 0 5 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 FAULTEN0 Fault Control Enable For n = 0 6 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 COMBINE1 Combine Channels For n = 2 8 1 read-write COMP1 Complement Of Channel (n) For n = 2 9 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAPEN1 Dual Edge Capture Mode Enable For n = 2 10 1 read-write DECAP1 Dual Edge Capture Mode Captures For n = 2 11 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DTEN1 Deadtime Enable For n = 2 12 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 SYNCEN1 Synchronization Enable For n = 2 13 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 FAULTEN1 Fault Control Enable For n = 2 14 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 COMBINE2 Combine Channels For n = 4 16 1 read-write COMP2 Complement Of Channel (n) For n = 4 17 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAPEN2 Dual Edge Capture Mode Enable For n = 4 18 1 read-write DECAP2 Dual Edge Capture Mode Captures For n = 4 19 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DTEN2 Deadtime Enable For n = 4 20 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 SYNCEN2 Synchronization Enable For n = 4 21 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 FAULTEN2 Fault Control Enable For n = 4 22 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 COMBINE3 Combine Channels For n = 6 24 1 read-write COMP3 Complement Of Channel (n) for n = 6 25 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAPEN3 Dual Edge Capture Mode Enable For n = 6 26 1 read-write DECAP3 Dual Edge Capture Mode Captures For n = 6 27 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DTEN3 Deadtime Enable For n = 6 28 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 SYNCEN3 Synchronization Enable For n = 6 29 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 FAULTEN3 Fault Control Enable For n = 6 30 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 DEADTIME Deadtime Insertion Control 0x68 32 read-write 0 0xFFFFFFFF DTVAL Deadtime Value 0 6 read-write DTPS Deadtime Prescaler Value 6 2 read-write 0x Divide the system clock by 1. #0x 10 Divide the system clock by 4. #10 11 Divide the system clock by 16. #11 EXTTRIG FTM External Trigger 0x6C 32 read-write 0 0xFFFFFFFF CH2TRIG Channel 2 Trigger Enable 0 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH3TRIG Channel 3 Trigger Enable 1 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH4TRIG Channel 4 Trigger Enable 2 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH5TRIG Channel 5 Trigger Enable 3 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH0TRIG Channel 0 Trigger Enable 4 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH1TRIG Channel 1 Trigger Enable 5 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 INITTRIGEN Initialization Trigger Enable 6 1 read-write 0 The generation of initialization trigger is disabled. #0 1 The generation of initialization trigger is enabled. #1 TRIGF Channel Trigger Flag 7 1 read-only 0 No channel trigger was generated. #0 1 A channel trigger was generated. #1 CH6TRIG Channel 6 Trigger Enable 8 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH7TRIG Channel 7 Trigger Enable 9 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 POL Channels Polarity 0x70 32 read-write 0 0xFFFFFFFF POL0 Channel 0 Polarity 0 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL1 Channel 1 Polarity 1 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL2 Channel 2 Polarity 2 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL3 Channel 3 Polarity 3 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL4 Channel 4 Polarity 4 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL5 Channel 5 Polarity 5 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL6 Channel 6 Polarity 6 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL7 Channel 7 Polarity 7 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 FMS Fault Mode Status 0x74 32 read-write 0 0xFFFFFFFF FAULTF0 Fault Detection Flag 0 0 1 read-only 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF1 Fault Detection Flag 1 1 1 read-only 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF2 Fault Detection Flag 2 2 1 read-only 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF3 Fault Detection Flag 3 3 1 read-only 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTIN Fault Inputs 5 1 read-only 0 The logic OR of the enabled fault inputs is 0. #0 1 The logic OR of the enabled fault inputs is 1. #1 WPEN Write Protection Enable 6 1 read-write 0 Write protection is disabled. Write protected bits can be written. #0 1 Write protection is enabled. Write protected bits cannot be written. #1 FAULTF Fault Detection Flag 7 1 read-only 0 No fault condition was detected. #0 1 A fault condition was detected. #1 FILTER Input Capture Filter Control 0x78 32 read-write 0 0xFFFFFFFF CH0FVAL Channel 0 Input Filter 0 4 read-write CH1FVAL Channel 1 Input Filter 4 4 read-write CH2FVAL Channel 2 Input Filter 8 4 read-write CH3FVAL Channel 3 Input Filter 12 4 read-write FLTCTRL Fault Control 0x7C 32 read-write 0 0xFFFFFFFF FAULT0EN Fault Input 0 Enable 0 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT1EN Fault Input 1 Enable 1 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT2EN Fault Input 2 Enable 2 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT3EN Fault Input 3 Enable 3 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FFLTR0EN Fault Input 0 Filter Enable 4 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR1EN Fault Input 1 Filter Enable 5 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR2EN Fault Input 2 Filter Enable 6 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR3EN Fault Input 3 Filter Enable 7 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFVAL Fault Input Filter 8 4 read-write FSTATE Fault output state 15 1 read-write 0 FTM outputs will be placed into safe values when fault events in ongoing (defined by POL bits). #0 1 FTM outputs will be tri-stated when fault event is ongoing #1 QDCTRL Quadrature Decoder Control And Status 0x80 32 read-write 0 0xFFFFFFFF QUADEN Quadrature Decoder Mode Enable 0 1 read-write 0 Quadrature Decoder mode is disabled. #0 1 Quadrature Decoder mode is enabled. #1 TOFDIR Timer Overflow Direction In Quadrature Decoder Mode 1 1 read-only 0 TOF bit was set on the bottom of counting. There was an FTM counter decrement and FTM counter changes from its minimum value (CNTIN register) to its maximum value (MOD register). #0 1 TOF bit was set on the top of counting. There was an FTM counter increment and FTM counter changes from its maximum value (MOD register) to its minimum value (CNTIN register). #1 QUADIR FTM Counter Direction In Quadrature Decoder Mode 2 1 read-only 0 Counting direction is decreasing (FTM counter decrement). #0 1 Counting direction is increasing (FTM counter increment). #1 QUADMODE Quadrature Decoder Mode 3 1 read-write 0 Phase A and phase B encoding mode. #0 1 Count and direction encoding mode. #1 PHBPOL Phase B Input Polarity 4 1 read-write 0 Normal polarity. Phase B input signal is not inverted before identifying the rising and falling edges of this signal. #0 1 Inverted polarity. Phase B input signal is inverted before identifying the rising and falling edges of this signal. #1 PHAPOL Phase A Input Polarity 5 1 read-write 0 Normal polarity. Phase A input signal is not inverted before identifying the rising and falling edges of this signal. #0 1 Inverted polarity. Phase A input signal is inverted before identifying the rising and falling edges of this signal. #1 PHBFLTREN Phase B Input Filter Enable 6 1 read-write 0 Phase B input filter is disabled. #0 1 Phase B input filter is enabled. #1 PHAFLTREN Phase A Input Filter Enable 7 1 read-write 0 Phase A input filter is disabled. #0 1 Phase A input filter is enabled. #1 CONF Configuration 0x84 32 read-write 0 0xFFFFFFFF LDFQ Load Frequency 0 5 read-write BDMMODE Debug Mode 6 2 read-write GTBEEN Global Time Base Enable 9 1 read-write 0 Use of an external global time base is disabled. #0 1 Use of an external global time base is enabled. #1 GTBEOUT Global Time Base Output 10 1 read-write 0 A global time base signal generation is disabled. #0 1 A global time base signal generation is enabled. #1 ITRIGR Initialization trigger on Reload Point 11 1 read-write 0 Initialization trigger is generated on counter wrap events. #0 1 Initialization trigger is generated when a reload point is reached. #1 FLTPOL FTM Fault Input Polarity 0x88 32 read-write 0 0xFFFFFFFF FLT0POL Fault Input 0 Polarity 0 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT1POL Fault Input 1 Polarity 1 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT2POL Fault Input 2 Polarity 2 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT3POL Fault Input 3 Polarity 3 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 SYNCONF Synchronization Configuration 0x8C 32 read-write 0 0xFFFFFFFF HWTRIGMODE Hardware Trigger Mode 0 1 read-write 0 FTM clears the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2. #0 1 FTM does not clear the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2. #1 CNTINC CNTIN Register Synchronization 2 1 read-write 0 CNTIN register is updated with its buffer value at all rising edges of system clock. #0 1 CNTIN register is updated with its buffer value by the PWM synchronization. #1 INVC INVCTRL Register Synchronization 4 1 read-write 0 INVCTRL register is updated with its buffer value at all rising edges of system clock. #0 1 INVCTRL register is updated with its buffer value by the PWM synchronization. #1 SWOC SWOCTRL Register Synchronization 5 1 read-write 0 SWOCTRL register is updated with its buffer value at all rising edges of system clock. #0 1 SWOCTRL register is updated with its buffer value by the PWM synchronization. #1 SYNCMODE Synchronization Mode 7 1 read-write 0 Legacy PWM synchronization is selected. #0 1 Enhanced PWM synchronization is selected. #1 SWRSTCNT FTM counter synchronization is activated by the software trigger. 8 1 read-write 0 The software trigger does not activate the FTM counter synchronization. #0 1 The software trigger activates the FTM counter synchronization. #1 SWWRBUF MOD, HCR, CNTIN, and CV registers synchronization is activated by the software trigger. 9 1 read-write 0 The software trigger does not activate MOD, HCR, CNTIN, and CV registers synchronization. #0 1 The software trigger activates MOD, HCR, CNTIN, and CV registers synchronization. #1 SWOM Output mask synchronization is activated by the software trigger. 10 1 read-write 0 The software trigger does not activate the OUTMASK register synchronization. #0 1 The software trigger activates the OUTMASK register synchronization. #1 SWINVC Inverting control synchronization is activated by the software trigger. 11 1 read-write 0 The software trigger does not activate the INVCTRL register synchronization. #0 1 The software trigger activates the INVCTRL register synchronization. #1 SWSOC Software output control synchronization is activated by the software trigger. 12 1 read-write 0 The software trigger does not activate the SWOCTRL register synchronization. #0 1 The software trigger activates the SWOCTRL register synchronization. #1 HWRSTCNT FTM counter synchronization is activated by a hardware trigger. 16 1 read-write 0 A hardware trigger does not activate the FTM counter synchronization. #0 1 A hardware trigger activates the FTM counter synchronization. #1 HWWRBUF MOD, HCR, CNTIN, and CV registers synchronization is activated by a hardware trigger. 17 1 read-write 0 A hardware trigger does not activate MOD, HCR, CNTIN, and CV registers synchronization. #0 1 A hardware trigger activates MOD, HCR, CNTIN, and CV registers synchronization. #1 HWOM Output mask synchronization is activated by a hardware trigger. 18 1 read-write 0 A hardware trigger does not activate the OUTMASK register synchronization. #0 1 A hardware trigger activates the OUTMASK register synchronization. #1 HWINVC Inverting control synchronization is activated by a hardware trigger. 19 1 read-write 0 A hardware trigger does not activate the INVCTRL register synchronization. #0 1 A hardware trigger activates the INVCTRL register synchronization. #1 HWSOC Software output control synchronization is activated by a hardware trigger. 20 1 read-write 0 A hardware trigger does not activate the SWOCTRL register synchronization. #0 1 A hardware trigger activates the SWOCTRL register synchronization. #1 INVCTRL FTM Inverting Control 0x90 32 read-write 0 0xFFFFFFFF INV0EN Pair Channels 0 Inverting Enable 0 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV1EN Pair Channels 1 Inverting Enable 1 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV2EN Pair Channels 2 Inverting Enable 2 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV3EN Pair Channels 3 Inverting Enable 3 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 SWOCTRL FTM Software Output Control 0x94 32 read-write 0 0xFFFFFFFF CH0OC Channel 0 Software Output Control Enable 0 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH1OC Channel 1 Software Output Control Enable 1 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH2OC Channel 2 Software Output Control Enable 2 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH3OC Channel 3 Software Output Control Enable 3 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH4OC Channel 4 Software Output Control Enable 4 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH5OC Channel 5 Software Output Control Enable 5 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH6OC Channel 6 Software Output Control Enable 6 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH7OC Channel 7 Software Output Control Enable 7 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH0OCV Channel 0 Software Output Control Value 8 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH1OCV Channel 1 Software Output Control Value 9 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH2OCV Channel 2 Software Output Control Value 10 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH3OCV Channel 3 Software Output Control Value 11 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH4OCV Channel 4 Software Output Control Value 12 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH5OCV Channel 5 Software Output Control Value 13 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH6OCV Channel 6 Software Output Control Value 14 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH7OCV Channel 7 Software Output Control Value 15 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 PWMLOAD FTM PWM Load 0x98 32 read-write 0 0xFFFFFFFF CH0SEL Channel 0 Select 0 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH1SEL Channel 1 Select 1 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH2SEL Channel 2 Select 2 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH3SEL Channel 3 Select 3 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH4SEL Channel 4 Select 4 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH5SEL Channel 5 Select 5 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH6SEL Channel 6 Select 6 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 CH7SEL Channel 7 Select 7 1 read-write 0 Channel match is not included as a reload opportunity. #0 1 Channel match is included as a reload opportunity. #1 HCSEL Half Cycle Select 8 1 read-write 0 Half cycle reload is disabled and it is not considered as a reload opportunity. #0 1 Half cycle reload is enabled and it is considered as a reload opportunity. #1 LDOK Load Enable 9 1 read-write 0 Loading updated values is disabled. #0 1 Loading updated values is enabled. #1 GLEN Global Load Enable 10 1 read-write 0 Global Load Ok disabled. #0 1 Global Load OK enabled. A pulse event on the module global load input sets the LDOK bit. #1 GLDOK Global Load OK 11 1 write-only 0 No action. #0 1 LDOK bit is set. #1 HCR Half Cycle Register 0x9C 32 read-write 0 0xFFFFFFFF HCVAL Half Cycle Value 0 16 read-write MOD_MIRROR Modulo 0x200 32 read-write 0 0xFFFFFFFF FRACMOD Fractional Value for MOD register 11 5 read-write MOD Modulo Value 16 16 read-write 8 0x4 0,1,2,3,4,5,6,7 C%sV_MIRROR Channel (n) Value 0x204 32 read-write 0 0xFFFFFFFF FRACVAL Fractional Value for VAL register 11 5 read-write VAL Channel Value 16 16 read-write RTC Secure Real Time Clock RTC_ 0x4003D000 0 0x808 registers RTC 20 TSR RTC Time Seconds Register 0 32 read-write 0 0xFFFFFFFF TSR Time Seconds Register 0 32 read-write TPR RTC Time Prescaler Register 0x4 32 read-write 0 0xFFFFFFFF TPR Time Prescaler Register 0 16 read-write TAR RTC Time Alarm Register 0x8 32 read-write 0 0xFFFFFFFF TAR Time Alarm Register 0 32 read-write TCR RTC Time Compensation Register 0xC 32 read-write 0 0xFFFFFFFF TCR Time Compensation Register 0 8 read-write 10000000 Time Prescaler Register overflows every 32896 clock cycles. #10000000 11111111 Time Prescaler Register overflows every 32769 clock cycles. #11111111 0 Time Prescaler Register overflows every 32768 clock cycles. #0 1 Time Prescaler Register overflows every 32767 clock cycles. #1 1111111 Time Prescaler Register overflows every 32641 clock cycles. #1111111 CIR Compensation Interval Register 8 8 read-write TCV Time Compensation Value 16 8 read-only CIC Compensation Interval Counter 24 8 read-only CR RTC Control Register 0x10 32 read-write 0 0xFFFFFFFF SWR Software Reset 0 1 read-write 0 No effect. #0 1 Resets all RTC registers except for the SWR bit and the RTC_WAR and RTC_RAR registers . The SWR bit is cleared by POR and by software explicitly clearing it. #1 WPE Wakeup Pin Enable 1 1 read-write 0 Wakeup pin is disabled. #0 1 Wakeup pin is enabled and wakeup pin asserts if the RTC interrupt asserts or the wakeup pin is turned on. #1 SUP Supervisor Access 2 1 read-write 0 Non-supervisor mode write accesses are not supported and generate a bus error. #0 1 Non-supervisor mode write accesses are supported. #1 UM Update Mode 3 1 read-write 0 Registers cannot be written when locked. #0 1 Registers can be written when locked under limited conditions. #1 WPS Wakeup Pin Select 4 1 read-write 0 Wakeup pin asserts (active low, open drain) if the RTC interrupt asserts or the wakeup pin is turned on. #0 1 Wakeup pin instead outputs the RTC 32kHz clock, provided the wakeup pin is turned on and the 32kHz clock is output to other peripherals. #1 CPS Clock Pin Select 5 1 read-write 0 The prescaler output clock (as configured by TSIC) is output on RTC_CLKOUT. #0 1 The RTC 32kHz crystal clock is output on RTC_CLKOUT. #1 LPOS LPO Select 7 1 read-write 0 RTC prescaler increments using 32 kHz crystal. #0 1 RTC prescaler increments using 128 kHz LPO, bits [4:0] of the prescaler are bypassed. #1 OSCE Oscillator Enable 8 1 read-write 0 32.768 kHz oscillator is disabled. #0 1 32.768 kHz oscillator is enabled. After setting this bit, wait the oscillator startup time before enabling the time counter to allow the 32.768 kHz clock time to stabilize. #1 CLKO Clock Output 9 1 read-write 0 The 32 kHz clock is allowed to output on RTC_CLKOUT. #0 1 The 32 kHz clock is not allowed to output on RTC_CLKOUT. #1 CPE Clock Pin Enable 24 2 read-write 00 RTC_CLKOUT is disabled. #00 01 RTC_CLKOUT is enabled. #01 SR RTC Status Register 0x14 32 read-write 0x1 0xFFFFFFFF TIF Time Invalid Flag 0 1 read-only 0 Time is valid. #0 1 Time is invalid and time counter is read as zero. #1 TOF Time Overflow Flag 1 1 read-only 0 Time overflow has not occurred. #0 1 Time overflow has occurred and time counter is read as zero. #1 TAF Time Alarm Flag 2 1 read-only 0 Time alarm has not occurred. #0 1 Time alarm has occurred. #1 TCE Time Counter Enable 4 1 read-write 0 Time counter is disabled. #0 1 Time counter is enabled. #1 LR RTC Lock Register 0x18 32 read-write 0xFF 0xFFFFFFFF TCL Time Compensation Lock 3 1 read-write 0 Time Compensation Register is locked and writes are ignored. #0 1 Time Compensation Register is not locked and writes complete as normal. #1 CRL Control Register Lock 4 1 read-write 0 Control Register is locked and writes are ignored. #0 1 Control Register is not locked and writes complete as normal. #1 SRL Status Register Lock 5 1 read-write 0 Status Register is locked and writes are ignored. #0 1 Status Register is not locked and writes complete as normal. #1 LRL Lock Register Lock 6 1 read-write 0 Lock Register is locked and writes are ignored. #0 1 Lock Register is not locked and writes complete as normal. #1 IER RTC Interrupt Enable Register 0x1C 32 read-write 0x7 0xFFFFFFFF TIIE Time Invalid Interrupt Enable 0 1 read-write 0 Time invalid flag does not generate an interrupt. #0 1 Time invalid flag does generate an interrupt. #1 TOIE Time Overflow Interrupt Enable 1 1 read-write 0 Time overflow flag does not generate an interrupt. #0 1 Time overflow flag does generate an interrupt. #1 TAIE Time Alarm Interrupt Enable 2 1 read-write 0 Time alarm flag does not generate an interrupt. #0 1 Time alarm flag does generate an interrupt. #1 TSIE Time Seconds Interrupt Enable 4 1 read-write 0 Seconds interrupt is disabled. #0 1 Seconds interrupt is enabled. #1 WPON Wakeup Pin On 7 1 read-write 0 No effect. #0 1 If the wakeup pin is enabled, then the wakeup pin will assert. #1 TSIC Timer Seconds Interrupt Configuration 16 3 read-write 000 1 Hz. #000 001 2 Hz. #001 010 4 Hz. #010 011 8 Hz. #011 100 16 Hz. #100 101 32 Hz. #101 110 64 Hz. #110 111 128 Hz. #111 WAR RTC Write Access Register 0x800 32 read-write 0xFF 0xFFFFFFFF TSRW Time Seconds Register Write 0 1 read-write 0 Writes to the Time Seconds Register are ignored. #0 1 Writes to the Time Seconds Register complete as normal. #1 TPRW Time Prescaler Register Write 1 1 read-write 0 Writes to the Time Prescaler Register are ignored. #0 1 Writes to the Time Prescaler Register complete as normal. #1 TARW Time Alarm Register Write 2 1 read-write 0 Writes to the Time Alarm Register are ignored. #0 1 Writes to the Time Alarm Register complete as normal. #1 TCRW Time Compensation Register Write 3 1 read-write 0 Writes to the Time Compensation Register are ignored. #0 1 Writes to the Time Compensation Register complete as normal. #1 CRW Control Register Write 4 1 read-write 0 Writes to the Control Register are ignored. #0 1 Writes to the Control Register complete as normal. #1 SRW Status Register Write 5 1 read-write 0 Writes to the Status Register are ignored. #0 1 Writes to the Status Register complete as normal. #1 LRW Lock Register Write 6 1 read-write 0 Writes to the Lock Register are ignored. #0 1 Writes to the Lock Register complete as normal. #1 IERW Interrupt Enable Register Write 7 1 read-write 0 Writes to the Interupt Enable Register are ignored. #0 1 Writes to the Interrupt Enable Register complete as normal. #1 RAR RTC Read Access Register 0x804 32 read-write 0xFF 0xFFFFFFFF TSRR Time Seconds Register Read 0 1 read-write 0 Reads to the Time Seconds Register are ignored. #0 1 Reads to the Time Seconds Register complete as normal. #1 TPRR Time Prescaler Register Read 1 1 read-write 0 Reads to the Time Pprescaler Register are ignored. #0 1 Reads to the Time Prescaler Register complete as normal. #1 TARR Time Alarm Register Read 2 1 read-write 0 Reads to the Time Alarm Register are ignored. #0 1 Reads to the Time Alarm Register complete as normal. #1 TCRR Time Compensation Register Read 3 1 read-write 0 Reads to the Time Compensation Register are ignored. #0 1 Reads to the Time Compensation Register complete as normal. #1 CRR Control Register Read 4 1 read-write 0 Reads to the Control Register are ignored. #0 1 Reads to the Control Register complete as normal. #1 SRR Status Register Read 5 1 read-write 0 Reads to the Status Register are ignored. #0 1 Reads to the Status Register complete as normal. #1 LRR Lock Register Read 6 1 read-write 0 Reads to the Lock Register are ignored. #0 1 Reads to the Lock Register complete as normal. #1 IERR Interrupt Enable Register Read 7 1 read-write 0 Reads to the Interrupt Enable Register are ignored. #0 1 Reads to the Interrupt Enable Register complete as normal. #1 LPTMR0 Low Power Timer LPTMR0_ 0x40040000 0 0x10 registers PWT_LPTMR0 29 CSR Low Power Timer Control Status Register 0 32 read-write 0 0xFFFFFFFF TEN Timer Enable 0 1 read-write 0 LPTMR is disabled and internal logic is reset. #0 1 LPTMR is enabled. #1 TMS Timer Mode Select 1 1 read-write 0 Time Counter mode. #0 1 Pulse Counter mode. #1 TFC Timer Free-Running Counter 2 1 read-write 0 CNR is reset whenever TCF is set. #0 1 CNR is reset on overflow. #1 TPP Timer Pin Polarity 3 1 read-write 0 Pulse Counter input source is active-high, and the CNR will increment on the rising-edge. #0 1 Pulse Counter input source is active-low, and the CNR will increment on the falling-edge. #1 TPS Timer Pin Select 4 2 read-write 00 Pulse counter input 0 is selected. #00 01 Pulse counter input 1 is selected. #01 10 Pulse counter input 2 is selected. #10 11 Pulse counter input 3 is selected. #11 TIE Timer Interrupt Enable 6 1 read-write 0 Timer interrupt disabled. #0 1 Timer interrupt enabled. #1 TCF Timer Compare Flag 7 1 read-write 0 The value of CNR is not equal to CMR and increments. #0 1 The value of CNR is equal to CMR and increments. #1 TDRE Timer DMA Request Enable 8 1 read-write 0 Timer DMA Request disabled. #0 1 Timer DMA Request enabled. #1 PSR Low Power Timer Prescale Register 0x4 32 read-write 0 0xFFFFFFFF PCS Prescaler Clock Select 0 2 read-write 00 Prescaler/glitch filter clock 0 selected. #00 01 Prescaler/glitch filter clock 1 selected. #01 10 Prescaler/glitch filter clock 2 selected. #10 11 Prescaler/glitch filter clock 3 selected. #11 PBYP Prescaler Bypass 2 1 read-write 0 Prescaler/glitch filter is enabled. #0 1 Prescaler/glitch filter is bypassed. #1 PRESCALE Prescale Value 3 4 read-write 0000 Prescaler divides the prescaler clock by 2; glitch filter does not support this configuration. #0000 0001 Prescaler divides the prescaler clock by 4; glitch filter recognizes change on input pin after 2 rising clock edges. #0001 0010 Prescaler divides the prescaler clock by 8; glitch filter recognizes change on input pin after 4 rising clock edges. #0010 0011 Prescaler divides the prescaler clock by 16; glitch filter recognizes change on input pin after 8 rising clock edges. #0011 0100 Prescaler divides the prescaler clock by 32; glitch filter recognizes change on input pin after 16 rising clock edges. #0100 0101 Prescaler divides the prescaler clock by 64; glitch filter recognizes change on input pin after 32 rising clock edges. #0101 0110 Prescaler divides the prescaler clock by 128; glitch filter recognizes change on input pin after 64 rising clock edges. #0110 0111 Prescaler divides the prescaler clock by 256; glitch filter recognizes change on input pin after 128 rising clock edges. #0111 1000 Prescaler divides the prescaler clock by 512; glitch filter recognizes change on input pin after 256 rising clock edges. #1000 1001 Prescaler divides the prescaler clock by 1024; glitch filter recognizes change on input pin after 512 rising clock edges. #1001 1010 Prescaler divides the prescaler clock by 2048; glitch filter recognizes change on input pin after 1024 rising clock edges. #1010 1011 Prescaler divides the prescaler clock by 4096; glitch filter recognizes change on input pin after 2048 rising clock edges. #1011 1100 Prescaler divides the prescaler clock by 8192; glitch filter recognizes change on input pin after 4096 rising clock edges. #1100 1101 Prescaler divides the prescaler clock by 16,384; glitch filter recognizes change on input pin after 8192 rising clock edges. #1101 1110 Prescaler divides the prescaler clock by 32,768; glitch filter recognizes change on input pin after 16,384 rising clock edges. #1110 1111 Prescaler divides the prescaler clock by 65,536; glitch filter recognizes change on input pin after 32,768 rising clock edges. #1111 CMR Low Power Timer Compare Register 0x8 32 read-write 0 0xFFFFFFFF COMPARE Compare Value 0 16 read-write CNR Low Power Timer Counter Register 0xC 32 read-write 0 0xFFFFFFFF COUNTER Counter Value 0 16 read-write SIM System Integration Module SIM_ 0x40048000 0x4 0x6C registers CHIPCTL Chip Control register 0x4 32 read-write 0 0xFFFFFFFF ADC_INTERLEAVE_EN ADC interleave channel enable 0 2 read-write 00 No interleave channel #00 CLKOUTDIV CLKOUT divider ratio 4 2 read-write 00 Divided by 1 #00 01 Divided by 2 #01 10 Divided by 4 #10 11 Divided by 8 #11 CLKOUTSEL CLKOUT Select 6 2 read-write 00 Reseved #00 01 SCGCLKOUT(SIRC/FIRC/SOSC/LPFLL), see SCG_CLKOUTCNFG register. #01 10 RTC oscillator (OSC32) clock (32 kHz) #10 11 LPO clock (128 kHz) #11 PDB_BB_SEL PDB back-to-back select 13 1 read-write 0 PDB0 channel 0 back-to-back operation with ADC0 COCO[1:0] and PDB0 channel 1 back-to-back operation with ADC1 COCO[1:0] #0 1 PDB0 Channel 0 back-to-back operation with COCO[0] of ADC0 and COCO[1] of ADC1 ; PDB0 Channel 1 back-to-back operation with COCO[0] of ADC1 and COCO[1] of ADC0 #1 PWTCLKSEL PWT clock source select 16 2 read-write 00 PWT alternative clock is from the TCLK0 pin. #00 01 PWT alternative clock is from the TCLK1 pin. #01 10 PWT alternative clock is from the TCLK2 pin. #10 RTC32KCLKSEL RTC 32K clock input select 18 2 read-write 00 OSC32 clock output #00 01 RTC_CLKIN #01 FTMOPT0 FTM Option Register 0 0xC 32 read-write 0 0xFFFFFFFF FTM0FLTxSEL FTM0 Fault x Select 0 3 read-write FTM0CLKSEL FTM0 External Clock Pin Select 24 2 read-write 00 FTM0 external clock driven by TCLK0 pin. #00 01 FTM0 external clock driven by TCLK1 pin. #01 10 FTM0 external clock driven by TCLK2 pin. #10 11 No clock input #11 FTM1CLKSEL FTM1 External Clock Pin Select 26 2 read-write 00 FTM1 external clock driven by TCLK0 pin. #00 01 FTM1 external clock driven by TCLK1 pin. #01 10 FTM1 external clock driven by TCLK2 pin. #10 11 No clock input #11 FTM2CLKSEL FTM2 External Clock Pin Select 28 2 read-write 00 FTM2 external clock driven by TCLK0 pin. #00 01 FTM2 external clock driven by TCLK1 pin. #01 10 FTM2 external clock driven by TCLK2 pin. #10 11 No clock input #11 ADCOPT ADC Options Register 0x18 32 read-write 0 0xFFFFFFFF ADC0TRGSEL ADC0 trigger source select 0 1 read-write 0 PDB output #0 1 TRGMUX output #1 ADC0SWPRETRG ADC0 software pre-trigger sources 1 2 read-write 00 software pre-trigger 0 #00 01 software pre-trigger 1 #01 10 software pre-trigger 2 #10 11 software pre-trigger 3 #11 ADC0PRETRGSEL ADC0 pre-trigger source select 4 2 read-write 00 PDB output #00 01 TRGMUX output #01 10 ADC0 software pre-trigger #10 ADC1TRGSEL ADC1 trigger source select 8 1 read-write 0 PDB output #0 1 TRGMUX output #1 ADC1SWPRETRG ADC1 software pre-trigger sources 9 2 read-write 00 software pre-trigger 0 #00 01 software pre-trigger 1 #01 10 software pre-trigger 2 #10 11 software pre-trigger 3 #11 ADC1PRETRGSEL ADC1 pre-trigger source select 12 2 read-write 00 PDB output #00 01 TRGMUX output #01 10 ADC1 software pre-trigger #10 FTMOPT1 FTM Option Register 1 0x1C 32 read-write 0 0xFFFFFFFF FTM0SYNCBIT FTM0 Sync Bit 0 1 read-write 0 No effect. #0 1 Write 1 to assert the TRIG1 input to FTM0. Software must clear this bit to allow other trigger sources to assert. #1 FTM1SYNCBIT FTM1 Sync Bit 1 1 read-write 0 No effect. #0 1 Write 1 to assert the TRIG1 input to FTM1. Software must clear this bit to allow other trigger sources to assert. #1 FTM2SYNCBIT FTM2 Sync Bit 2 1 read-write 0 No effect. #0 1 Write 1 to assert the TRIG1 input to FTM2. Software must clear this bit to allow other trigger sources to assert. #1 FTM1CH0SEL FTM1 CH0 Select 4 2 read-write 00 FTM1_CH0 input #00 01 CMP0 output #01 10 CMP1 output #10 FTM2CH0SEL FTM2 CH0 Select 6 2 read-write 00 FTM2_CH0 input #00 01 CMP0 output #01 10 CMP1 output #10 FTM2CH1SEL FTM2 CH1 Select 8 1 read-write 0 FTM2_CH1 input #0 1 exclusive OR of FTM2_CH0, FTM2_CH1, and FTM1_CH1 #1 FTM0_OUTSEL FTM0 channel modulation select with FTM1_CH1 16 8 read-write 0 No modulation with FTM1_CH1 #0 1 Modulation with FTM1_CH1 #1 SDID System Device Identification Register 0x24 32 read-only 0x100 0xF80 PINID Pin identification 0 7 read-only 0111 64-pin #111 1000 80-pin #1000 1010 100-pin #1010 PROJECTID Project ID 7 5 read-only REVID Device revision number 12 4 read-only RAMSIZE RAM size 16 4 read-only 0101 16 KB #0101 0110 32 KB #0110 SERIESID Kinetis Series ID 20 4 read-only 0010 Kinetis E+ series #0010 SUBFAMID Kinetis E-series Sub-Family ID 24 4 read-only FAMILYID Kinetis E-series Family ID 28 4 read-only 0000 KE0x Family (Entry level) #0000 0001 KE1x Family (Enhanced features) #0001 0011 KE3x Family (with SLCD) #0011 FCFG1 Flash Configuration Register 1 0x4C 32 read-write 0 0xF00FFF FLASHDIS Flash Disable 0 1 read-write 0 Flash is enabled #0 1 Flash is disabled #1 FLASHDOZE Flash Doze 1 1 read-write 0 Flash remains enabled during Doze mode #0 1 Flash is disabled for the duration of Doze mode #1 DEPART FlexNVM partition 12 4 read-only EEERAMSIZE EEE SRAM SIZE 16 4 read-only 0011 2 KB #0011 0100 1 KB #0100 0101 512 Bytes #0101 0110 256 Bytes #0110 0111 128 Bytes #0111 1000 64 Bytes #1000 1001 32 Bytes #1001 PFSIZE Program flash size 24 4 read-only 0111 128 KB of program flash memory, 4 KB protection region #0111 1001 256 KB of program flash memory, 8 KB protection region #1001 NVMSIZE FlexNVM size 28 4 read-only 0000 0 KB of FlexNVM #0000 0011 32 KB of FlexNVM #0011 FCFG2 Flash Configuration Register 2 0x50 32 read-only 0 0 MAXADDR1 Max address block 1 16 7 read-only MAXADDR0 Max address block 0 24 7 read-only UIDH Unique Identification Register High 0x54 32 read-only 0 0xFFFFFFFF UID127_96 Unique Identification 0 32 read-only UIDMH Unique Identification Register Mid-High 0x58 32 read-only 0 0xFFFFFFFF UID95_64 Unique Identification 0 32 read-only UIDML Unique Identification Register Mid Low 0x5C 32 read-only 0 0xFFFFFFFF UID63_32 Unique Identification 0 32 read-only UIDL Unique Identification Register Low 0x60 32 read-only 0 0xFFFFFFFF UID31_0 Unique Identification 0 32 read-only MISCTRL Miscellaneous Control register 0x6C 32 read-write 0 0xFFFFFFFF SW_TRG Software Trigger bit to TRGMUX 0 1 read-write DMA_INT_SEL DMA channel interrupt OR select 4 4 read-write UART0ODE UART0 Open Drain Enable 16 1 read-write 0 Open drain is disabled on UART0 #0 1 Open drain is enabled on UART0 #1 UART1ODE UART1 Open Drain Enable 17 1 read-write 0 Open drain is disabled on UART1 #0 1 Open drain is enabled on UART1 #1 UART2ODE UART2 Open Drain Enable 18 1 read-write 0 Open drain is disabled on UART2 #0 1 Open drain is enabled on UART2 #1 PORTA Pin Control and Interrupts PORT PORTA_ 0x40049000 0 0xCC registers PORTAE 7 PCR0 Pin Control Register n 0 32 read-write 0x2 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR1 Pin Control Register n 0x4 32 read-write 0x3 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR2 Pin Control Register n 0x8 32 read-write 0x3 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR3 Pin Control Register n 0xC 32 read-write 0x3 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR4 Pin Control Register n 0x10 32 read-write 0x3 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR5 Pin Control Register n 0x14 32 read-write 0x1 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR6 Pin Control Register n 0x18 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR7 Pin Control Register n 0x1C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR8 Pin Control Register n 0x20 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR9 Pin Control Register n 0x24 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR10 Pin Control Register n 0x28 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR11 Pin Control Register n 0x2C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR12 Pin Control Register n 0x30 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR13 Pin Control Register n 0x34 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR14 Pin Control Register n 0x38 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR15 Pin Control Register n 0x3C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR16 Pin Control Register n 0x40 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR17 Pin Control Register n 0x44 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR18 Pin Control Register n 0x48 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR19 Pin Control Register n 0x4C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR20 Pin Control Register n 0x50 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR21 Pin Control Register n 0x54 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR22 Pin Control Register n 0x58 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR23 Pin Control Register n 0x5C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR24 Pin Control Register n 0x60 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR25 Pin Control Register n 0x64 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR26 Pin Control Register n 0x68 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR27 Pin Control Register n 0x6C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR28 Pin Control Register n 0x70 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR29 Pin Control Register n 0x74 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR30 Pin Control Register n 0x78 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR31 Pin Control Register n 0x7C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCHR Global Pin Control High Register 0x84 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write 0 0xFFFFFFFF ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 DFER Digital Filter Enable Register 0xC0 32 read-write 0 0xFFFFFFFF DFE Digital Filter Enable 0 32 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFCR Digital Filter Clock Register 0xC4 32 read-write 0 0xFFFFFFFF CS Clock Source 0 1 read-write 0 Digital filters are clocked by the bus clock. #0 1 Digital filters are clocked by the LPO clock. #1 DFWR Digital Filter Width Register 0xC8 32 read-write 0 0xFFFFFFFF FILT Filter Length 0 5 read-write PORTB Pin Control and Interrupts PORT PORTB_ 0x4004A000 0 0xCC registers PORTBCD 26 PCR0 Pin Control Register n 0 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR1 Pin Control Register n 0x4 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR2 Pin Control Register n 0x8 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR3 Pin Control Register n 0xC 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR4 Pin Control Register n 0x10 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR5 Pin Control Register n 0x14 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR6 Pin Control Register n 0x18 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR7 Pin Control Register n 0x1C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR8 Pin Control Register n 0x20 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR9 Pin Control Register n 0x24 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR10 Pin Control Register n 0x28 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR11 Pin Control Register n 0x2C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR12 Pin Control Register n 0x30 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR13 Pin Control Register n 0x34 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR14 Pin Control Register n 0x38 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR15 Pin Control Register n 0x3C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR16 Pin Control Register n 0x40 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR17 Pin Control Register n 0x44 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR18 Pin Control Register n 0x48 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR19 Pin Control Register n 0x4C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR20 Pin Control Register n 0x50 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR21 Pin Control Register n 0x54 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR22 Pin Control Register n 0x58 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR23 Pin Control Register n 0x5C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR24 Pin Control Register n 0x60 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR25 Pin Control Register n 0x64 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR26 Pin Control Register n 0x68 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR27 Pin Control Register n 0x6C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR28 Pin Control Register n 0x70 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR29 Pin Control Register n 0x74 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR30 Pin Control Register n 0x78 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR31 Pin Control Register n 0x7C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCHR Global Pin Control High Register 0x84 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write 0 0xFFFFFFFF ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 DFER Digital Filter Enable Register 0xC0 32 read-write 0 0xFFFFFFFF DFE Digital Filter Enable 0 32 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFCR Digital Filter Clock Register 0xC4 32 read-write 0 0xFFFFFFFF CS Clock Source 0 1 read-write 0 Digital filters are clocked by the bus clock. #0 1 Digital filters are clocked by the LPO clock. #1 DFWR Digital Filter Width Register 0xC8 32 read-write 0 0xFFFFFFFF FILT Filter Length 0 5 read-write PORTC Pin Control and Interrupts PORT PORTC_ 0x4004B000 0 0xCC registers PORTBCD 26 PCR0 Pin Control Register n 0 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR1 Pin Control Register n 0x4 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR2 Pin Control Register n 0x8 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR3 Pin Control Register n 0xC 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR4 Pin Control Register n 0x10 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR5 Pin Control Register n 0x14 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR6 Pin Control Register n 0x18 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR7 Pin Control Register n 0x1C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR8 Pin Control Register n 0x20 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR9 Pin Control Register n 0x24 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR10 Pin Control Register n 0x28 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR11 Pin Control Register n 0x2C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR12 Pin Control Register n 0x30 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR13 Pin Control Register n 0x34 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR14 Pin Control Register n 0x38 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR15 Pin Control Register n 0x3C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR16 Pin Control Register n 0x40 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR17 Pin Control Register n 0x44 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR18 Pin Control Register n 0x48 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR19 Pin Control Register n 0x4C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR20 Pin Control Register n 0x50 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR21 Pin Control Register n 0x54 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR22 Pin Control Register n 0x58 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR23 Pin Control Register n 0x5C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR24 Pin Control Register n 0x60 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR25 Pin Control Register n 0x64 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR26 Pin Control Register n 0x68 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR27 Pin Control Register n 0x6C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR28 Pin Control Register n 0x70 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR29 Pin Control Register n 0x74 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR30 Pin Control Register n 0x78 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR31 Pin Control Register n 0x7C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCHR Global Pin Control High Register 0x84 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write 0 0xFFFFFFFF ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 DFER Digital Filter Enable Register 0xC0 32 read-write 0 0xFFFFFFFF DFE Digital Filter Enable 0 32 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFCR Digital Filter Clock Register 0xC4 32 read-write 0 0xFFFFFFFF CS Clock Source 0 1 read-write 0 Digital filters are clocked by the bus clock. #0 1 Digital filters are clocked by the LPO clock. #1 DFWR Digital Filter Width Register 0xC8 32 read-write 0 0xFFFFFFFF FILT Filter Length 0 5 read-write PORTD Pin Control and Interrupts PORT PORTD_ 0x4004C000 0 0xCC registers PORTBCD 26 PCR0 Pin Control Register n 0 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR1 Pin Control Register n 0x4 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR2 Pin Control Register n 0x8 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR3 Pin Control Register n 0xC 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR4 Pin Control Register n 0x10 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR5 Pin Control Register n 0x14 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR6 Pin Control Register n 0x18 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR7 Pin Control Register n 0x1C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR8 Pin Control Register n 0x20 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR9 Pin Control Register n 0x24 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR10 Pin Control Register n 0x28 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR11 Pin Control Register n 0x2C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR12 Pin Control Register n 0x30 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR13 Pin Control Register n 0x34 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR14 Pin Control Register n 0x38 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR15 Pin Control Register n 0x3C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR16 Pin Control Register n 0x40 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR17 Pin Control Register n 0x44 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR18 Pin Control Register n 0x48 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR19 Pin Control Register n 0x4C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR20 Pin Control Register n 0x50 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR21 Pin Control Register n 0x54 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR22 Pin Control Register n 0x58 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR23 Pin Control Register n 0x5C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR24 Pin Control Register n 0x60 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR25 Pin Control Register n 0x64 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR26 Pin Control Register n 0x68 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR27 Pin Control Register n 0x6C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR28 Pin Control Register n 0x70 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR29 Pin Control Register n 0x74 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR30 Pin Control Register n 0x78 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR31 Pin Control Register n 0x7C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCHR Global Pin Control High Register 0x84 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write 0 0xFFFFFFFF ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 DFER Digital Filter Enable Register 0xC0 32 read-write 0 0xFFFFFFFF DFE Digital Filter Enable 0 32 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFCR Digital Filter Clock Register 0xC4 32 read-write 0 0xFFFFFFFF CS Clock Source 0 1 read-write 0 Digital filters are clocked by the bus clock. #0 1 Digital filters are clocked by the LPO clock. #1 DFWR Digital Filter Width Register 0xC8 32 read-write 0 0xFFFFFFFF FILT Filter Length 0 5 read-write PORTE Pin Control and Interrupts PORT PORTE_ 0x4004D000 0 0xCC registers PORTAE 7 PCR0 Pin Control Register n 0 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR1 Pin Control Register n 0x4 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR2 Pin Control Register n 0x8 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR3 Pin Control Register n 0xC 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR4 Pin Control Register n 0x10 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR5 Pin Control Register n 0x14 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR6 Pin Control Register n 0x18 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR7 Pin Control Register n 0x1C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR8 Pin Control Register n 0x20 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR9 Pin Control Register n 0x24 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR10 Pin Control Register n 0x28 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR11 Pin Control Register n 0x2C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR12 Pin Control Register n 0x30 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR13 Pin Control Register n 0x34 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR14 Pin Control Register n 0x38 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR15 Pin Control Register n 0x3C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR16 Pin Control Register n 0x40 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR17 Pin Control Register n 0x44 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR18 Pin Control Register n 0x48 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR19 Pin Control Register n 0x4C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR20 Pin Control Register n 0x50 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR21 Pin Control Register n 0x54 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR22 Pin Control Register n 0x58 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR23 Pin Control Register n 0x5C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR24 Pin Control Register n 0x60 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR25 Pin Control Register n 0x64 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR26 Pin Control Register n 0x68 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR27 Pin Control Register n 0x6C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR28 Pin Control Register n 0x70 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR29 Pin Control Register n 0x74 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR30 Pin Control Register n 0x78 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR31 Pin Control Register n 0x7C 32 read-write 0 0xFFFFFFFF PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (Alternative 0) (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt Status Flag (ISF) is disabled. #0000 0001 ISF flag and DMA request on rising edge. #0001 0010 ISF flag and DMA request on falling edge. #0010 0011 ISF flag and DMA request on either edge. #0011 1000 ISF flag and Interrupt when logic 0. #1000 1001 ISF flag and Interrupt on rising-edge. #1001 1010 ISF flag and Interrupt on falling-edge. #1010 1011 ISF flag and Interrupt on either edge. #1011 1100 ISF flag and Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCHR Global Pin Control High Register 0x84 32 write-only 0 0xFFFFFFFF GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write 0 0xFFFFFFFF ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 DFER Digital Filter Enable Register 0xC0 32 read-write 0 0xFFFFFFFF DFE Digital Filter Enable 0 32 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFCR Digital Filter Clock Register 0xC4 32 read-write 0 0xFFFFFFFF CS Clock Source 0 1 read-write 0 Digital filters are clocked by the bus clock. #0 1 Digital filters are clocked by the LPO clock. #1 DFWR Digital Filter Width Register 0xC8 32 read-write 0 0xFFFFFFFF FILT Filter Length 0 5 read-write WDOG Watchdog timer WDOG_ 0x40052000 0 0x10 registers WDOG_EWM 28 CS Watchdog Control and Status Register 0 32 read-write 0x2980 0xFFFFFFFF STOP Stop Enable 0 1 read-write 0 Watchdog disabled in chip stop mode. #0 1 Watchdog enabled in chip stop mode. #1 WAIT Wait Enable 1 1 read-write 0 Watchdog disabled in chip wait mode. #0 1 Watchdog enabled in chip wait mode. #1 DBG Debug Enable 2 1 read-write 0 Watchdog disabled in chip debug mode. #0 1 Watchdog enabled in chip debug mode. #1 TST Watchdog Test 3 2 read-write 00 Watchdog test mode disabled. #00 01 Watchdog user mode enabled. (Watchdog test mode disabled.) After testing the watchdog, software should use this setting to indicate that the watchdog is functioning normally in user mode. #01 10 Watchdog test mode enabled, only the low byte is used. CNT[CNTLOW] is compared with TOVAL[TOVALLOW]. #10 11 Watchdog test mode enabled, only the high byte is used. CNT[CNTHIGH] is compared with TOVAL[TOVALHIGH]. #11 UPDATE Allow updates 5 1 read-write 0 Updates not allowed. After the initial configuration, the watchdog cannot be later modified without forcing a reset. #0 1 Updates allowed. Software can modify the watchdog configuration registers within 128 bus clocks after performing the unlock write sequence. #1 INT Watchdog Interrupt 6 1 read-write 0 Watchdog interrupts are disabled. Watchdog resets are not delayed. #0 1 Watchdog interrupts are enabled. Watchdog resets are delayed by 128 bus clocks from the interrupt vector fetch. #1 EN Watchdog Enable 7 1 read-write 0 Watchdog disabled. #0 1 Watchdog enabled. #1 CLK Watchdog Clock 8 2 read-write 00 Bus clock #00 01 LPO clock (128k LPO, 32k LPO, 1k LPO, or 32k OSC), whose selection is controlled via SIM_LPOCLKS[LPOCLKSEL]. #01 10 System oscillator clock (SOSC, from SCG) #10 11 Slow internal reference clock (SIRC, from SCG) #11 RCS Reconfiguration Success 10 1 read-only 0 Reconfiguring WDOG. #0 1 Reconfiguration is successful. #1 ULK Unlock status 11 1 read-only 0 WDOG is locked. #0 1 WDOG is unlocked. #1 PRES Watchdog prescaler 12 1 read-write 0 256 prescaler disabled. #0 1 256 prescaler enabled. #1 CMD32EN Enables or disables WDOG support for 32-bit (or 16-bit or 8-bit) refresh/unlock command write words 13 1 read-write 0 Disables support for 32-bit (or 16-bit or 8-bit) refresh/unlock command write words #0 1 Enables support for 32-bit (or 16-bit or 8-bit) refresh/unlock command write words #1 FLG Watchdog Interrupt Flag 14 1 read-write 0 No interrupt occurred. #0 1 An interrupt occurred. #1 WIN Watchdog Window 15 1 read-write 0 Window mode disabled. #0 1 Window mode enabled. #1 CNT Watchdog Counter Register 0x4 32 read-write 0 0xFFFFFFFF CNTLOW Low byte of the Watchdog Counter 0 8 read-write CNTHIGH High byte of the Watchdog Counter 8 8 read-write TOVAL Watchdog Timeout Value Register 0x8 32 read-write 0x400 0xFFFFFFFF TOVALLOW Low byte of the timeout value 0 8 read-write TOVALHIGH High byte of the timeout value 8 8 read-write WIN Watchdog Window Register 0xC 32 read-write 0 0xFFFFFFFF WINLOW Low byte of Watchdog Window 0 8 read-write WINHIGH High byte of Watchdog Window 8 8 read-write PWT Pulse Width Timer PWT_ 0x40056000 0 0x8 registers PWT_LPTMR0 29 CS Pulse Width Timer Control and Status Register 0 8 read-write 0 0xFF PWTOV PWT Counter Overflow 0 1 read-write 0 PWT counter no overflow. #0 1 PWT counter runs from 0xFFFF to 0x0000. #1 PWTRDY PWT Pulse Width Valid 1 1 read-write 0 PWT pulse width register(s) is not up-to-date. #0 1 PWT pulse width register(s) has been updated. #1 FCTLE First counter load enable after enable 2 1 read-write 0 Do not load the first counter values to corresponding registers #0 1 Load the first coutner value to corresponding registers depended by the PWTIN level #1 PWTSR PWT Soft Reset 3 1 write-only 0 No action taken. #0 1 Writing 1 to this field will perform soft reset to PWT. #1 POVIE PWT Counter Overflow Interrupt Enable 4 1 read-write 0 Disable PWT to generate interrupt when PWTOV is set. #0 1 Enable PWT to generate interrupt when PWTOV is set. #1 PRDYIE PWT Pulse Width Data Ready Interrupt Enable 5 1 read-write 0 Disable PWT to generate interrupt when PWTRDY is set. #0 1 Enable PWT to generate interrupt when PWTRDY is set. #1 PWTIE PWT Module Interrupt Enable 6 1 read-write 0 Disables the PWT to generate interrupt. #0 1 Enables the PWT to generate interrupt. #1 PWTEN PWT Module Enable 7 1 read-write 0 The PWT is disabled. #0 1 The PWT is enabled. #1 CR Pulse Width Timer Control Register 0x1 8 read-write 0 0xFF PRE PWT Clock Prescaler (CLKPRE) Setting 0 3 read-write 000 Clock divided by 1. #000 001 Clock divided by 2. #001 010 Clock divided by 4. #010 011 Clock divided by 8. #011 100 Clock divided by 16. #100 101 Clock divided by 32. #101 110 Clock divided by 64. #110 111 Clock divided by 128. #111 LVL PWTIN Level when Overflows 3 1 read-only TGL PWTIN states Toggled from last state 4 1 read-write 0 The selected PWTIN hasn't changed its original states from last time. #0 1 The selected PWTIN has toggled its states. #1 PINSEL PWT Pulse Inputs Selection 5 2 read-write 00 PWTIN[0] is enabled. #00 01 PWTIN[1] is enabled. #01 10 PWTIN[2] enabled. #10 11 PWTIN[3] enabled. #11 PCLKS PWT Clock Source Selection 7 1 read-write 0 BUS_CLK is selected as the clock source of PWT counter. #0 1 Alternative clock is selected as the clock source of PWT counter. #1 PPH Pulse Width Timer Positive Pulse Width Register: High 0x2 8 read-only 0 0xFF PPWH Positive Pulse Width[15:8] 0 8 read-only PPL Pulse Width Timer Positive Pulse Width Register: Loq 0x3 8 read-only 0 0xFF PPWL Positive Pulse Width[7:0] 0 8 read-only NPH Pulse Width Timer Negative Pulse Width Register: High 0x4 8 read-only 0 0xFF NPWH Negative Pulse Width[15:8] 0 8 read-only NPL Pulse Width Timer Negative Pulse Width Register: Low 0x5 8 read-only 0 0xFF NPWL Negative Pulse Width[7:0] 0 8 read-only CNTH Pulse Width Timer Counter Register: High 0x6 8 read-only 0 0xFF PWTH PWT counter[15:8] 0 8 read-only CNTL Pulse Width Timer Counter Register: Low 0x7 8 read-only 0 0xFF PWTL PWT counter[7:0] 0 8 read-only FLEXIO The FLEXIO Memory Map/Register Definition can be found here. FLEXIO_ 0x4005A000 0 0x510 registers FLEXIO 23 VERID Version ID Register 0 32 read-only 0x1010000 0xFFFFFFFF FEATURE Feature Specification Number 0 16 read-only 0 Standard features implemented. #0 1 Supports state, logic and parallel modes. #1 MINOR Minor Version Number 16 8 read-only MAJOR Major Version Number 24 8 read-only PARAM Parameter Register 0x4 32 read-only 0x4080404 0xFFFFFFFF SHIFTER Shifter Number 0 8 read-only TIMER Timer Number 8 8 read-only PIN Pin Number 16 8 read-only TRIGGER Trigger Number 24 8 read-only CTRL FlexIO Control Register 0x8 32 read-write 0 0xFFFFFFFF FLEXEN FlexIO Enable 0 1 read-write 0 FlexIO module is disabled. #0 1 FlexIO module is enabled. #1 SWRST Software Reset 1 1 read-write 0 Software reset is disabled #0 1 Software reset is enabled, all FlexIO registers except the Control Register are reset. #1 FASTACC Fast Access 2 1 read-write 0 Configures for normal register accesses to FlexIO #0 1 Configures for fast register accesses to FlexIO #1 DBGE Debug Enable 30 1 read-write 0 FlexIO is disabled in debug modes. #0 1 FlexIO is enabled in debug modes #1 DOZEN Doze Enable 31 1 read-write 0 FlexIO enabled in Doze modes. #0 1 FlexIO disabled in Doze modes. #1 PIN Pin State Register 0xC 32 read-only 0 0xFFFFFFFF PDI Pin Data Input 0 8 read-only SHIFTSTAT Shifter Status Register 0x10 32 read-write 0 0xFFFFFFFF SSF Shifter Status Flag 0 4 read-write 0 Status flag is clear #0000 1 Status flag is set #0001 SHIFTERR Shifter Error Register 0x14 32 read-write 0 0xFFFFFFFF SEF Shifter Error Flags 0 4 read-write 0 Shifter Error Flag is clear #0000 1 Shifter Error Flag is set #0001 TIMSTAT Timer Status Register 0x18 32 read-write 0 0xFFFFFFFF TSF Timer Status Flags 0 4 read-write 0 Timer Status Flag is clear #0000 1 Timer Status Flag is set #0001 SHIFTSIEN Shifter Status Interrupt Enable 0x20 32 read-write 0 0xFFFFFFFF SSIE Shifter Status Interrupt Enable 0 4 read-write 0 Shifter Status Flag interrupt disabled #0000 1 Shifter Status Flag interrupt enabled #0001 SHIFTEIEN Shifter Error Interrupt Enable 0x24 32 read-write 0 0xFFFFFFFF SEIE Shifter Error Interrupt Enable 0 4 read-write 0 Shifter Error Flag interrupt disabled #0000 1 Shifter Error Flag interrupt enabled #0001 TIMIEN Timer Interrupt Enable Register 0x28 32 read-write 0 0xFFFFFFFF TEIE Timer Status Interrupt Enable 0 4 read-write 0 Timer Status Flag interrupt is disabled #0000 1 Timer Status Flag interrupt is enabled #0001 SHIFTSDEN Shifter Status DMA Enable 0x30 32 read-write 0 0xFFFFFFFF SSDE Shifter Status DMA Enable 0 4 read-write 0 Shifter Status Flag DMA request is disabled #0000 1 Shifter Status Flag DMA request is enabled #0001 SHIFTSTATE Shifter State Register 0x40 32 read-write 0 0xFFFFFFFF STATE Current State Pointer 0 3 read-write 4 0x4 0,1,2,3 SHIFTCTL%s Shifter Control N Register 0x80 32 read-write 0 0xFFFFFFFF SMOD Shifter Mode 0 3 read-write 000 Disabled. #000 001 Receive mode. Captures the current Shifter content into the SHIFTBUF on expiration of the Timer. #001 010 Transmit mode. Load SHIFTBUF contents into the Shifter on expiration of the Timer. #010 100 Match Store mode. Shifter data is compared to SHIFTBUF content on expiration of the Timer. #100 101 Match Continuous mode. Shifter data is continuously compared to SHIFTBUF contents. #101 110 State mode. SHIFTBUF contents are used for storing programmable state attributes. #110 111 Logic mode. SHIFTBUF contents are used for implementing programmable logic look up table. #111 PINPOL Shifter Pin Polarity 7 1 read-write 0 Pin is active high #0 1 Pin is active low #1 PINSEL Shifter Pin Select 8 3 read-write PINCFG Shifter Pin Configuration 16 2 read-write 00 Shifter pin output disabled #00 01 Shifter pin open drain or bidirectional output enable #01 10 Shifter pin bidirectional output data #10 11 Shifter pin output #11 TIMPOL Timer Polarity 23 1 read-write 0 Shift on posedge of Shift clock #0 1 Shift on negedge of Shift clock #1 TIMSEL Timer Select 24 2 read-write 4 0x4 0,1,2,3 SHIFTCFG%s Shifter Configuration N Register 0x100 32 read-write 0 0xFFFFFFFF SSTART Shifter Start bit 0 2 read-write 00 Start bit disabled for transmitter/receiver/match store, transmitter loads data on enable #00 01 Start bit disabled for transmitter/receiver/match store, transmitter loads data on first shift #01 10 Transmitter outputs start bit value 0 before loading data on first shift, receiver/match store sets error flag if start bit is not 0 #10 11 Transmitter outputs start bit value 1 before loading data on first shift, receiver/match store sets error flag if start bit is not 1 #11 SSTOP Shifter Stop bit 4 2 read-write 00 Stop bit disabled for transmitter/receiver/match store #00 01 Reserved for transmitter/receiver/match store #01 10 Transmitter outputs stop bit value 0 on store, receiver/match store sets error flag if stop bit is not 0 #10 11 Transmitter outputs stop bit value 1 on store, receiver/match store sets error flag if stop bit is not 1 #11 INSRC Input Source 8 1 read-write 0 Pin #0 1 Shifter N+1 Output #1 4 0x4 0,1,2,3 SHIFTBUF%s Shifter Buffer N Register 0x200 32 read-write 0 0xFFFFFFFF SHIFTBUF Shift Buffer 0 32 read-write 4 0x4 0,1,2,3 SHIFTBUFBIS%s Shifter Buffer N Bit Swapped Register 0x280 32 read-write 0 0xFFFFFFFF SHIFTBUFBIS Shift Buffer 0 32 read-write 4 0x4 0,1,2,3 SHIFTBUFBYS%s Shifter Buffer N Byte Swapped Register 0x300 32 read-write 0 0xFFFFFFFF SHIFTBUFBYS Shift Buffer 0 32 read-write 4 0x4 0,1,2,3 SHIFTBUFBBS%s Shifter Buffer N Bit Byte Swapped Register 0x380 32 read-write 0 0xFFFFFFFF SHIFTBUFBBS Shift Buffer 0 32 read-write 4 0x4 0,1,2,3 TIMCTL%s Timer Control N Register 0x400 32 read-write 0 0xFFFFFFFF TIMOD Timer Mode 0 2 read-write 00 Timer Disabled. #00 01 Dual 8-bit counters baud/bit mode. #01 10 Dual 8-bit counters PWM mode. #10 11 Single 16-bit counter mode. #11 PINPOL Timer Pin Polarity 7 1 read-write 0 Pin is active high #0 1 Pin is active low #1 PINSEL Timer Pin Select 8 3 read-write PINCFG Timer Pin Configuration 16 2 read-write 00 Timer pin output disabled #00 01 Timer pin open drain or bidirectional output enable #01 10 Timer pin bidirectional output data #10 11 Timer pin output #11 TRGSRC Trigger Source 22 1 read-write 0 External trigger selected #0 1 Internal trigger selected #1 TRGPOL Trigger Polarity 23 1 read-write 0 Trigger active high #0 1 Trigger active low #1 TRGSEL Trigger Select 24 4 read-write 4 0x4 0,1,2,3 TIMCFG%s Timer Configuration N Register 0x480 32 read-write 0 0xFFFFFFFF TSTART Timer Start Bit 1 1 read-write 0 Start bit disabled #0 1 Start bit enabled #1 TSTOP Timer Stop Bit 4 2 read-write 00 Stop bit disabled #00 01 Stop bit is enabled on timer compare #01 10 Stop bit is enabled on timer disable #10 11 Stop bit is enabled on timer compare and timer disable #11 TIMENA Timer Enable 8 3 read-write 000 Timer always enabled #000 001 Timer enabled on Timer N-1 enable #001 010 Timer enabled on Trigger high #010 011 Timer enabled on Trigger high and Pin high #011 100 Timer enabled on Pin rising edge #100 101 Timer enabled on Pin rising edge and Trigger high #101 110 Timer enabled on Trigger rising edge #110 111 Timer enabled on Trigger rising or falling edge #111 TIMDIS Timer Disable 12 3 read-write 000 Timer never disabled #000 001 Timer disabled on Timer N-1 disable #001 010 Timer disabled on Timer compare #010 011 Timer disabled on Timer compare and Trigger Low #011 100 Timer disabled on Pin rising or falling edge #100 101 Timer disabled on Pin rising or falling edge provided Trigger is high #101 110 Timer disabled on Trigger falling edge #110 TIMRST Timer Reset 16 3 read-write 000 Timer never reset #000 010 Timer reset on Timer Pin equal to Timer Output #010 011 Timer reset on Timer Trigger equal to Timer Output #011 100 Timer reset on Timer Pin rising edge #100 110 Timer reset on Trigger rising edge #110 111 Timer reset on Trigger rising or falling edge #111 TIMDEC Timer Decrement 20 2 read-write 00 Decrement counter on FlexIO clock, Shift clock equals Timer output. #00 01 Decrement counter on Trigger input (both edges), Shift clock equals Timer output. #01 10 Decrement counter on Pin input (both edges), Shift clock equals Pin input. #10 11 Decrement counter on Trigger input (both edges), Shift clock equals Trigger input. #11 TIMOUT Timer Output 24 2 read-write 00 Timer output is logic one when enabled and is not affected by timer reset #00 01 Timer output is logic zero when enabled and is not affected by timer reset #01 10 Timer output is logic one when enabled and on timer reset #10 11 Timer output is logic zero when enabled and on timer reset #11 4 0x4 0,1,2,3 TIMCMP%s Timer Compare N Register 0x500 32 read-write 0 0xFFFFFFFF CMP Timer Compare Value 0 16 read-write OSC32 RTC Oscillator OSC32_ 0x40060000 0 0x1 registers CR RTC Oscillator Control Register 0 8 read-write 0 0xFF ROSCEREFS RTC 32k Oscillator external reference clcok selection 4 1 read-write 0 Bypass mode. RTC oscillator selects the external 32k clock. #0 1 Crystal mode. #1 ROSCSTB RTC 32k Oscillator stable flag 5 1 read-only 0 RTC 32k oscillator is unstable now and no clock will go out of the block. #0 1 RTC 32k oscillator is stable. #1 ROSCSTPEN RTC 32k Oscillator stop mode enable 6 1 read-write 0 Oscillator is disabled regardless the state of ROSCEN. #0 1 Oscillator is enabled in Stop mode when ROSCEN is set. #1 ROSCEN RTC 32k Oscillator enable 7 1 read-write 0 Oscillator is disabled. #0 1 Oscillator is enabled. #1 EWM External Watchdog Monitor EWM_ 0x40061000 0 0x6 registers WDOG_EWM 28 CTRL Control Register 0 8 read-write 0 0xFF EWMEN EWM enable. 0 1 read-write ASSIN EWM_in's Assertion State Select. 1 1 read-write INEN Input Enable. 2 1 read-write INTEN Interrupt Enable. 3 1 read-write SERV Service Register 0x1 8 write-only 0 0xFF SERVICE The EWM refresh mechanism requires the CPU to write two values to the SERV register: a first data byte of 0xB4, followed by a second data byte of 0x2C 0 8 write-only CMPL Compare Low Register 0x2 8 read-write 0 0xFF COMPAREL To prevent runaway code from changing this field, software should write to this field after a CPU reset even if the (default) minimum refresh time is required 0 8 read-write CMPH Compare High Register 0x3 8 read-write 0xFF 0xFF COMPAREH To prevent runaway code from changing this field, software should write to this field after a CPU reset even if the (default) maximum refresh time is required 0 8 read-write CLKPRESCALER Clock Prescaler Register 0x5 8 read-write 0 0xFF CLK_DIV Selected low power clock source for running the EWM counter can be prescaled as below 0 8 read-write TRGMUX0 TRGMUX TRGMUX 0x40062000 0 0x70 registers TRGMUX_DMAMUX0 TRGMUX Register 0 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write SEL1 Trigger MUX Input 1 Source Select 8 6 read-write SEL2 Trigger MUX Input 2 Source Select 16 6 read-write SEL3 Trigger MUX Input 3 Source Select 24 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_EXTOUT0 TRGMUX Register 0x4 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write SEL1 Trigger MUX Input 1 Source Select 8 6 read-write SEL2 Trigger MUX Input 2 Source Select 16 6 read-write SEL3 Trigger MUX Input 3 Source Select 24 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_EXTOUT1 TRGMUX Register 0x8 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write SEL1 Trigger MUX Input 1 Source Select 8 6 read-write SEL2 Trigger MUX Input 2 Source Select 16 6 read-write SEL3 Trigger MUX Input 3 Source Select 24 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_ADC0 TRGMUX Register 0xC 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write SEL1 Trigger MUX Input 1 Source Select 8 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_ADC1 TRGMUX Register 0x10 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write SEL1 Trigger MUX Input 1 Source Select 8 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_CMP0 TRGMUX Register 0x1C 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_CMP1 TRGMUX Register 0x20 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_FTM0 TRGMUX Register 0x28 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write SEL1 Trigger MUX Input 1 Source Select 8 6 read-write SEL2 Trigger MUX Input 2 Source Select 16 6 read-write SEL3 Trigger MUX Input 3 Source Select 24 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_FTM1 TRGMUX Register 0x2C 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write SEL1 Trigger MUX Input 1 Source Select 8 6 read-write SEL2 Trigger MUX Input 2 Source Select 16 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_FTM2 TRGMUX Register 0x30 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write SEL1 Trigger MUX Input 1 Source Select 8 6 read-write SEL2 Trigger MUX Input 2 Source Select 16 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_PDB0 TRGMUX Register 0x38 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_FLEXIO TRGMUX Register 0x44 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write SEL1 Trigger MUX Input 1 Source Select 8 6 read-write SEL2 Trigger MUX Input 2 Source Select 16 6 read-write SEL3 Trigger MUX Input 3 Source Select 24 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_LPIT0 TRGMUX Register 0x48 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write SEL1 Trigger MUX Input 1 Source Select 8 6 read-write SEL2 Trigger MUX Input 2 Source Select 16 6 read-write SEL3 Trigger MUX Input 3 Source Select 24 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_LPUART0 TRGMUX Register 0x4C 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_LPUART1 TRGMUX Register 0x50 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_LPI2C0 TRGMUX Register 0x54 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_LPI2C1 TRGMUX Register 0x58 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_LPSPI0 TRGMUX Register 0x5C 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_LPSPI1 TRGMUX Register 0x60 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_LPTMR0 TRGMUX Register 0x64 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_PWT TRGMUX Register 0x6C 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX1 TRGMUX TRGMUX 0x40063000 0 0x8 registers TRGMUX_CTRL0 TRGMUX Register 0 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write SEL1 Trigger MUX Input 1 Source Select 8 6 read-write SEL2 Trigger MUX Input 2 Source Select 16 6 read-write SEL3 Trigger MUX Input 3 Source Select 24 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 TRGMUX_CTRL1 TRGMUX Register 0x4 32 read-write 0 0xFFFFFFFF SEL0 Trigger MUX Input 0 Source Select 0 6 read-write SEL1 Trigger MUX Input 1 Source Select 8 6 read-write SEL2 Trigger MUX Input 2 Source Select 16 6 read-write SEL3 Trigger MUX Input 3 Source Select 24 6 read-write LK Enable 31 1 read-only 0 Register can be written. #0 1 Register cannot be written until the next system Reset. #1 SCG System Clock Generator SCG_ 0x40064000 0 0x518 registers SCG 27 VERID Version ID Register 0 32 read-only 0x1000000 0xFFFFFFFF VERSION SCG Version Number 0 32 read-only PARAM Parameter Register 0x4 32 read-only 0xF80000FE 0xFFFFFFFF CLKPRES Clock Present 0 8 read-only DIVPRES Divider Present 27 5 read-only CSR Clock Status Register 0x10 32 read-only 0x3000001 0xFFFFFFFF DIVSLOW Slow Clock Divide Ratio 0 4 read-only 0001 Divide-by-2 #0001 0010 Divide-by-3 #0010 0011 Divide-by-4 #0011 0100 Divide-by-5 #0100 0101 Divide-by-6 #0101 0110 Divide-by-7 #0110 0111 Divide-by-8 #0111 DIVCORE Core Clock Divide Ratio 16 4 read-only 0000 Divide-by-1 #0000 0001 Divide-by-2 #0001 0010 Divide-by-3 #0010 0011 Divide-by-4 #0011 0100 Divide-by-5 #0100 0101 Divide-by-6 #0101 0110 Divide-by-7 #0110 0111 Divide-by-8 #0111 1000 Divide-by-9 #1000 1001 Divide-by-10 #1001 1010 Divide-by-11 #1010 1011 Divide-by-12 #1011 1100 Divide-by-13 #1100 1101 Divide-by-14 #1101 1110 Divide-by-15 #1110 1111 Divide-by-16 #1111 SCS System Clock Source 24 4 read-only 0001 System OSC #0001 0010 Slow IRC #0010 0011 Fast IRC #0011 0101 Low Power FLL (LPFLL) #0101 RCCR Run Clock Control Register 0x14 32 read-write 0x3000001 0xFFFFFFFF DIVSLOW Slow Clock Divide Ratio 0 4 read-write 0001 Divide-by-2 #0001 0010 Divide-by-3 #0010 0011 Divide-by-4 #0011 0100 Divide-by-5 #0100 0101 Divide-by-6 #0101 0110 Divide-by-7 #0110 0111 Divide-by-8 #0111 DIVCORE Core Clock Divide Ratio 16 4 read-write 0000 Divide-by-1 #0000 0001 Divide-by-2 #0001 0010 Divide-by-3 #0010 0011 Divide-by-4 #0011 0100 Divide-by-5 #0100 0101 Divide-by-6 #0101 0110 Divide-by-7 #0110 0111 Divide-by-8 #0111 1000 Divide-by-9 #1000 1001 Divide-by-10 #1001 1010 Divide-by-11 #1010 1011 Divide-by-12 #1011 1100 Divide-by-13 #1100 1101 Divide-by-14 #1101 1110 Divide-by-15 #1110 1111 Divide-by-16 #1111 SCS System Clock Source 24 4 read-write 0001 System OSC #0001 0010 Slow IRC #0010 0011 Fast IRC #0011 0101 Low Power FLL (LPFLL) #0101 VCCR VLPR Clock Control Register 0x18 32 read-write 0x2000001 0xFFFFFFFF DIVSLOW Slow Clock Divide Ratio 0 4 read-write 0001 Divide-by-2 #0001 0010 Divide-by-3 #0010 0011 Divide-by-4 #0011 0100 Divide-by-5 #0100 0101 Divide-by-6 #0101 0110 Divide-by-7 #0110 0111 Divide-by-8 #0111 DIVCORE Core Clock Divide Ratio 16 4 read-write 0000 Divide-by-1 #0000 0001 Divide-by-2 #0001 0010 Divide-by-3 #0010 0011 Divide-by-4 #0011 0100 Divide-by-5 #0100 0101 Divide-by-6 #0101 0110 Divide-by-7 #0110 0111 Divide-by-8 #0111 1000 Divide-by-9 #1000 1001 Divide-by-10 #1001 1010 Divide-by-11 #1010 1011 Divide-by-12 #1011 1100 Divide-by-13 #1100 1101 Divide-by-14 #1101 1110 Divide-by-15 #1110 1111 Divide-by-16 #1111 SCS System Clock Source 24 4 read-write 0001 System OSC #0001 0010 Slow IRC #0010 CLKOUTCNFG SCG CLKOUT Configuration Register 0x20 32 read-write 0x3000000 0xFFFFFFFF CLKOUTSEL SCG Clkout Select 24 4 read-write 0000 SCG SLOW Clock #0000 0001 System OSC #0001 0010 Slow IRC #0010 0011 Fast IRC #0011 0101 Low Power FLL (LPFLL) #0101 SOSCCSR System OSC Control Status Register 0x100 32 read-write 0 0xFFFFFFFF SOSCEN System OSC Enable 0 1 read-write 0 System OSC is disabled #0 1 System OSC is enabled #1 SOSCSTEN System OSC Stop Enable 1 1 read-write 0 System OSC is disabled in Stop modes #0 1 System OSC is enabled in Stop modes if SOSCEN=1. #1 SOSCLPEN System OSC Low Power Enable 2 1 read-write 0 System OSC is disabled in VLP modes #0 1 System OSC is enabled in VLP modes #1 SOSCERCLKEN System OSC 3V ERCLK Enable 3 1 read-write 0 System OSC 3V ERCLK output clock is disabled. #0 1 System OSC 3V ERCLK output clock is enabled when SYSOSC is enabled. #1 SOSCCM System OSC Clock Monitor 16 1 read-write 0 System OSC Clock Monitor is disabled #0 1 System OSC Clock Monitor is enabled #1 SOSCCMRE System OSC Clock Monitor Reset Enable 17 1 read-write 0 Clock Monitor generates interrupt when error detected #0 1 Clock Monitor generates reset when error detected #1 LK Lock Register 23 1 read-write 0 This Control Status Register can be written. #0 1 This Control Status Register cannot be written. #1 SOSCVLD System OSC Valid 24 1 read-only 0 System OSC is not enabled or clock is not valid #0 1 System OSC is enabled and output clock is valid #1 SOSCSEL System OSC Selected 25 1 read-only 0 System OSC is not the system clock source #0 1 System OSC is the system clock source #1 SOSCERR System OSC Clock Error 26 1 read-write 0 System OSC Clock Monitor is disabled or has not detected an error #0 1 System OSC Clock Monitor is enabled and detected an error #1 SOSCDIV System OSC Divide Register 0x104 32 read-write 0 0xFFFFFFFF SOSCDIV1 System OSC Clock Divide 1 0 3 read-write 000 Output disabled #000 001 Divide by 1 #001 010 Divide by 2 #010 011 Divide by 4 #011 100 Divide by 8 #100 101 Divide by 16 #101 110 Divide by 32 #110 111 Divide by 64 #111 SOSCDIV2 System OSC Clock Divide 2 8 3 read-write 000 Output disabled #000 001 Divide by 1 #001 010 Divide by 2 #010 011 Divide by 4 #011 100 Divide by 8 #100 101 Divide by 16 #101 110 Divide by 32 #110 111 Divide by 64 #111 SOSCCFG System Oscillator Configuration Register 0x108 32 read-write 0x10 0xFFFFFFFF EREFS External Reference Select 2 1 read-write 0 External reference clock selected #0 1 Internal crystal oscillator of OSC requested. #1 HGO High Gain Oscillator Select 3 1 read-write 0 Configure crystal oscillaor for low-power operation #0 1 Configure crystal oscillator for high-gain operation #1 RANGE System OSC Range Select 4 2 read-write 01 Low frequency range selected for the crystal oscillator of 32 kHz to 40 kHz. #01 10 Medium frequency range selected for the crytstal oscillator of 1 Mhz to 8 Mhz. #10 11 High frequency range selected for the crystal oscillator of 8 Mhz to 32 Mhz. #11 SIRCCSR Slow IRC Control Status Register 0x200 32 read-write 0x1000005 0xFFFFFFFF SIRCEN Slow IRC Enable 0 1 read-write 0 Slow IRC is disabled #0 1 Slow IRC is enabled #1 SIRCSTEN Slow IRC Stop Enable 1 1 read-write 0 Slow IRC is disabled in Stop modes #0 1 Slow IRC is enabled in Stop modes #1 SIRCLPEN Slow IRC Low Power Enable 2 1 read-write 0 Slow IRC is disabled in VLP modes #0 1 Slow IRC is enabled in VLP modes #1 LK Lock Register 23 1 read-write 0 Control Status Register can be written. #0 1 Control Status Register cannot be written. #1 SIRCVLD Slow IRC Valid 24 1 read-only 0 Slow IRC is not enabled or clock is not valid #0 1 Slow IRC is enabled and output clock is valid #1 SIRCSEL Slow IRC Selected 25 1 read-only 0 Slow IRC is not the system clock source #0 1 Slow IRC is the system clock source #1 SIRCDIV Slow IRC Divide Register 0x204 32 read-write 0 0xFFFFFFFF SIRCDIV1 Slow IRC Clock Divide 1 0 3 read-write 000 Output disabled #000 001 Divide by 1 #001 010 Divide by 2 #010 011 Divide by 4 #011 100 Divide by 8 #100 101 Divide by 16 #101 110 Divide by 32 #110 111 Divide by 64 #111 SIRCDIV2 Slow IRC Clock Divide 2 8 3 read-write 000 Output disabled #000 001 Divide by 1 #001 010 Divide by 2 #010 011 Divide by 4 #011 100 Divide by 8 #100 101 Divide by 16 #101 110 Divide by 32 #110 111 Divide by 64 #111 SIRCCFG Slow IRC Configuration Register 0x208 32 read-write 0x1 0xFFFFFFFF RANGE Frequency Range 0 1 read-write 0 Slow IRC low range clock (2 MHz) #0 1 Slow IRC high range clock (8 MHz ) #1 FIRCCSR Fast IRC Control Status Register 0x300 32 read-write 0x1 0xFFFFFFFF FIRCEN Fast IRC Enable 0 1 read-write 0 Fast IRC is disabled #0 1 Fast IRC is enabled #1 FIRCSTEN Fast IRC Stop Enable 1 1 read-write 0 Fast IRC is disabled in Stop modes. When selected as the reference clock to the System PLL and if the System PLL is enabled in STOP mode, the Fast IRC will stay enabled even if FIRCSTEN=0. #0 1 Fast IRC is enabled in Stop modes #1 FIRCLPEN Fast IRC Low Power Enable 2 1 read-write 0 Fast IRC is disabled in VLP modes #0 1 Fast IRC is enabled in VLP modes #1 FIRCREGOFF Fast IRC Regulator Enable 3 1 read-write 0 Fast IRC Regulator is enabled. #0 1 Fast IRC Regulator is disabled. #1 FIRCTREN Fast IRC Trim Enable 8 1 read-write 0 Disable trimming Fast IRC to an external clock source #0 1 Enable trimming Fast IRC to an external clock source #1 FIRCTRUP Fast IRC Trim Update 9 1 read-write 0 Disable Fast IRC trimming updates #0 1 Enable Fast IRC trimming updates #1 LK Lock Register 23 1 read-write 0 Control Status Register can be written. #0 1 Control Status Register cannot be written. #1 FIRCVLD Fast IRC Valid status 24 1 read-only 0 Fast IRC is not enabled or clock is not valid #0 1 Fast IRC is enabled and output clock is valid #1 FIRCSEL Fast IRC Selected status 25 1 read-only 0 Fast IRC is not the system clock source #0 1 Fast IRC is the system clock source #1 FIRCERR Fast IRC Clock Error 26 1 read-write 0 Error not detected with the Fast IRC trimming. #0 1 Error detected with the Fast IRC trimming. #1 FIRCDIV Fast IRC Divide Register 0x304 32 read-write 0 0xFFFFFFFF FIRCDIV1 Fast IRC Clock Divide 1 0 3 read-write 000 Output disabled #000 001 Divide by 1 #001 010 Divide by 2 #010 011 Divide by 4 #011 100 Divide by 8 #100 101 Divide by 16 #101 110 Divide by 32 #110 111 Divide by 64 #111 FIRCDIV2 Fast IRC Clock Divide 2 8 3 read-write 000 Output disabled #000 001 Divide by 1 #001 010 Divide by 2 #010 011 Divide by 4 #011 100 Divide by 8 #100 101 Divide by 16 #101 110 Divide by 32 #110 111 Divide by 64 #111 FIRCCFG Fast IRC Configuration Register 0x308 32 read-write 0 0xFFFFFFFF RANGE Frequency Range 0 2 read-write 00 Fast IRC is trimmed to 48 MHz #00 01 Fast IRC is trimmed to 52 MHz #01 10 Fast IRC is trimmed to 56 MHz #10 11 Fast IRC is trimmed to 60 MHz #11 FIRCTCFG Fast IRC Trim Configuration Register 0x30C 32 read-write 0 0xFFFFFFFF TRIMSRC Trim Source 0 2 read-write 10 System OSC #10 TRIMDIV Fast IRC Trim Predivide 8 3 read-write 000 Divide by 1 #000 001 Divide by 128 #001 010 Divide by 256 #010 011 Divide by 512 #011 100 Divide by 1024 #100 101 Divide by 2048 #101 110 Reserved. Writing this value will result in Divide by 1. #110 111 Reserved. Writing this value will result in a Divide by 1. #111 FIRCSTAT Fast IRC Status Register 0x318 32 read-write 0 0xFFFFFFFF TRIMFINE Trim Fine Status 0 7 read-write TRIMCOAR Trim Coarse 8 6 read-write ROSCCSR RTC OSC Control Status Register 0x400 32 read-write 0 0xFFFFFFFF ROSCCM RTC OSC Clock Monitor 16 1 read-write 0 RTC OSC Clock Monitor is disabled #0 1 RTC OSC Clock Monitor is enabled #1 ROSCCMRE RTC OSC Clock Monitor Reset Enable 17 1 read-write 0 Clock Monitor generates interrupt when error detected #0 1 Clock Monitor generates reset when error detected #1 LK Lock Register 23 1 read-write 0 Control Status Register can be written. #0 1 Control Status Register cannot be written. #1 ROSCVLD RTC OSC Valid 24 1 read-only 0 RTC OSC is not enabled or clock is not valid #0 1 RTC OSC is enabled and output clock is valid #1 ROSCERR RTC OSC Clock Error 26 1 read-write 0 RTC OSC Clock Monitor is disabled or has not detected an error #0 1 RTC OSC Clock Monitor is enabled and detected an RTC loss of clock error #1 LPFLLCSR Low Power FLL Control Status Register 0x500 32 read-write 0 0xFFFFFFFF LPFLLEN LPFLL Enable 0 1 read-write 0 LPFLL is disabled #0 1 LPFLL is enabled #1 LPFLLTREN LPFLL Trim Enable 8 1 read-write 0 Disable trimming LPFLL to an reference clock source #0 1 Enable trimming LPFLL to an reference clock source #1 LPFLLTRUP LPFLL Trim Update 9 1 read-write 0 Disable LPFLL trimming updates. LPFLL frequency determined by AUTOTRIM written value. #0 1 Enable LPFLL trimming updates. LPFLL frequency determined by reference clock multiplication #1 LPFLLTRMLOCK LPFLL Trim LOCK 10 1 read-only 0 LPFLL not Locked #0 1 LPFLL trimmed and Locked #1 LPFLLCM LPFLL Clock Monitor 16 1 read-write 0 LPFLL Clock Monitor is disabled #0 1 LPFLL Clock Monitor is enabled #1 LPFLLCMRE LPFLL Clock Monitor Reset Enable 17 1 read-write 0 Clock Monitor generates interrupt when error detected #0 1 Clock Monitor generates reset when error detected #1 LK Lock Register 23 1 read-write 0 Control Status Register can be written. #0 1 Control Status Register cannot be written. #1 LPFLLVLD LPFLL Valid 24 1 read-only 0 LPFLL is not enabled or clock is not valid. #0 1 LPFLL is enabled and output clock is valid. #1 LPFLLSEL LPFLL Selected 25 1 read-only 0 LPFLL is not the system clock source #0 1 LPFLL is the system clock source #1 LPFLLERR LPFLL Clock Error 26 1 read-write 0 Error not detected with the LPFLL trimming. #0 1 Error detected with the LPFLL trimming. #1 LPFLLDIV Low Power FLL Divide Register 0x504 32 read-write 0 0xFFFFFFFF LPFLLDIV1 LPFLL Clock Divide 1 0 3 read-write 000 Output disabled #000 001 Divide by 1 #001 010 Divide by 2 #010 011 Divide by 4 #011 100 Divide by 8 #100 101 Divide by 16 #101 110 Divide by 32 #110 111 Divide by 64 #111 LPFLLDIV2 LPFLL Clock Divide 2 8 3 read-write 000 Output disabled #000 001 Divide by 1 #001 010 Divide by 2 #010 011 Divide by 4 #011 100 Divide by 8 #100 101 Divide by 16 #101 110 Divide by 32 #110 111 Divide by 64 #111 LPFLLCFG Low Power FLL Configuration Register 0x508 32 read-write 0 0xFFFFFFFF FSEL Frequency Select 0 2 read-write 00 LPFLL is trimmed to 48 MHz #00 01 LPFLL is trimmed to 72 MHz #01 LPFLLTCFG Low Power FLL Trim Configuration Register 0x50C 32 read-write 0 0xFFFFFFFF TRIMSRC Trim Source 0 2 read-write 00 SIRC #00 01 FIRC #01 10 System OSC #10 11 RTC OSC #11 TRIMDIV LPFLL Trim Predivide 8 5 read-write LOCKW2LSB Lock LPFLL with 2 LSBS 16 1 read-write 0 LPFLL locks within 1LSB (0.4%) #0 1 LPFLL locks within 2LSB (0.8%) #1 LPFLLSTAT Low Power FLL Status Register 0x514 32 read-write 0 0xFFFFFFFF AUTOTRIM Auto Tune Trim Status 0 8 read-write PCC PCC 0x40065000 0x20 0x1B4 registers PCC_DMA0 PCC Register 0x20 32 read-write 0xC0000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_FLASH PCC Register 0x80 32 read-write 0xC0000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_DMAMUX0 PCC Register 0x84 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_ADC1 PCC Register 0x9C 32 read-write 0xC0000000 0xFFFFFFFF PCS Peripheral Clock Source Select 24 3 read-write 000 Clock is off (or test clock is enabled). #000 1 OSCCLK - System Oscillator Bus Clock(scg_sosc_slow_clk). #001 2 SCGIRCLK - Slow IRC Clock(scg_sirc_slow_clk), (maximum is 8MHz). #010 3 SCGFIRCLK - Fast IRC Clock(scg_firc_slow_clk), (maximum is 48MHz). #011 6 SCGPCLK System PLL clock(scg_spll_slow_clk). #110 INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_LPSPI0 PCC Register 0xB0 32 read-write 0x80000000 0xFFFFFFFF PCS Peripheral Clock Source Select 24 3 read-write 000 Clock is off (or test clock is enabled). #000 1 OSCCLK - System Oscillator Bus Clock(scg_sosc_slow_clk). #001 2 SCGIRCLK - Slow IRC Clock(scg_sirc_slow_clk), (maximum is 8MHz). #010 3 SCGFIRCLK - Fast IRC Clock(scg_firc_slow_clk), (maximum is 48MHz). #011 6 SCGPCLK System PLL clock(scg_spll_slow_clk). #110 INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_LPSPI1 PCC Register 0xB4 32 read-write 0x80000000 0xFFFFFFFF PCS Peripheral Clock Source Select 24 3 read-write 000 Clock is off (or test clock is enabled). #000 1 OSCCLK - System Oscillator Bus Clock(scg_sosc_slow_clk). #001 2 SCGIRCLK - Slow IRC Clock(scg_sirc_slow_clk), (maximum is 8MHz). #010 3 SCGFIRCLK - Fast IRC Clock(scg_firc_slow_clk), (maximum is 48MHz). #011 6 SCGPCLK System PLL clock(scg_spll_slow_clk). #110 INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_CRC PCC Register 0xC8 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_PDB0 PCC Register 0xD8 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_LPIT0 PCC Register 0xDC 32 read-write 0x80000000 0xFFFFFFFF PCS Peripheral Clock Source Select 24 3 read-write 000 Clock is off (or test clock is enabled). #000 1 OSCCLK - System Oscillator Bus Clock(scg_sosc_slow_clk). #001 2 SCGIRCLK - Slow IRC Clock(scg_sirc_slow_clk), (maximum is 8MHz). #010 3 SCGFIRCLK - Fast IRC Clock(scg_firc_slow_clk), (maximum is 48MHz). #011 6 SCGPCLK System PLL clock(scg_spll_slow_clk). #110 INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_FLEXTMR0 PCC Register 0xE0 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_FLEXTMR1 PCC Register 0xE4 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_FLEXTMR2 PCC Register 0xE8 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_ADC0 PCC Register 0xEC 32 read-write 0xC0000000 0xFFFFFFFF PCS Peripheral Clock Source Select 24 3 read-write 000 Clock is off (or test clock is enabled). #000 1 OSCCLK - System Oscillator Bus Clock(scg_sosc_slow_clk). #001 2 SCGIRCLK - Slow IRC Clock(scg_sirc_slow_clk), (maximum is 8MHz). #010 3 SCGFIRCLK - Fast IRC Clock(scg_firc_slow_clk), (maximum is 48MHz). #011 6 SCGPCLK System PLL clock(scg_spll_slow_clk). #110 INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_RTC PCC Register 0xF4 32 read-write 0x80000000 0xFFFFFFFF PCD Peripheral Clock Divider Select 0 3 read-write 0 Divide by 1 (pass-through, no clock divide). #000 1 Divide by 2. #001 2 Divide by 3. #010 3 Divide by 4. #011 4 Divide by 5. #100 5 Divide by 6. #101 6 Divide by 7. #110 7 Divide by 8. #111 FRAC Peripheral Clock Divider Fraction 3 1 read-write 0 Fractional value is 0. #0 1 Fractional value is 1. #1 INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_LPTMR0 PCC Register 0x100 32 read-write 0x80000000 0xFFFFFFFF PCD Peripheral Clock Divider Select 0 3 read-write 0 Divide by 1 (pass-through, no clock divide). #000 1 Divide by 2. #001 2 Divide by 3. #010 3 Divide by 4. #011 4 Divide by 5. #100 5 Divide by 6. #101 6 Divide by 7. #110 7 Divide by 8. #111 FRAC Peripheral Clock Divider Fraction 3 1 read-write 0 Fractional value is 0. #0 1 Fractional value is 1. #1 PCS Peripheral Clock Source Select 24 3 read-write 000 Clock is off (or test clock is enabled). #000 1 OSCCLK - System Oscillator Bus Clock(scg_sosc_slow_clk). #001 2 SCGIRCLK - Slow IRC Clock(scg_sirc_slow_clk), (maximum is 8MHz). #010 3 SCGFIRCLK - Fast IRC Clock(scg_firc_slow_clk), (maximum is 48MHz). #011 6 SCGPCLK System PLL clock(scg_spll_slow_clk). #110 INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_PORTA PCC Register 0x124 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_PORTB PCC Register 0x128 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_PORTC PCC Register 0x12C 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_PORTD PCC Register 0x130 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_PORTE PCC Register 0x134 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_PWT PCC Register 0x158 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_FLEXIO PCC Register 0x168 32 read-write 0x80000000 0xFFFFFFFF PCS Peripheral Clock Source Select 24 3 read-write 000 Clock is off (or test clock is enabled). #000 1 OSCCLK - System Oscillator Bus Clock(scg_sosc_slow_clk). #001 2 SCGIRCLK - Slow IRC Clock(scg_sirc_slow_clk), (maximum is 8MHz). #010 3 SCGFIRCLK - Fast IRC Clock(scg_firc_slow_clk), (maximum is 48MHz). #011 6 SCGPCLK System PLL clock(scg_spll_slow_clk). #110 INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_OSC32 PCC Register 0x180 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_EWM PCC Register 0x184 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_LPI2C0 PCC Register 0x198 32 read-write 0x80000000 0xFFFFFFFF PCS Peripheral Clock Source Select 24 3 read-write 000 Clock is off (or test clock is enabled). #000 1 OSCCLK - System Oscillator Bus Clock(scg_sosc_slow_clk). #001 2 SCGIRCLK - Slow IRC Clock(scg_sirc_slow_clk), (maximum is 8MHz). #010 3 SCGFIRCLK - Fast IRC Clock(scg_firc_slow_clk), (maximum is 48MHz). #011 6 SCGPCLK System PLL clock(scg_spll_slow_clk). #110 INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_LPI2C1 PCC Register 0x19C 32 read-write 0x80000000 0xFFFFFFFF PCS Peripheral Clock Source Select 24 3 read-write 000 Clock is off (or test clock is enabled). #000 1 OSCCLK - System Oscillator Bus Clock(scg_sosc_slow_clk). #001 2 SCGIRCLK - Slow IRC Clock(scg_sirc_slow_clk), (maximum is 8MHz). #010 3 SCGFIRCLK - Fast IRC Clock(scg_firc_slow_clk), (maximum is 48MHz). #011 6 SCGPCLK System PLL clock(scg_spll_slow_clk). #110 INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_LPUART0 PCC Register 0x1A8 32 read-write 0x80000000 0xFFFFFFFF PCS Peripheral Clock Source Select 24 3 read-write 000 Clock is off (or test clock is enabled). #000 1 OSCCLK - System Oscillator Bus Clock(scg_sosc_slow_clk). #001 2 SCGIRCLK - Slow IRC Clock(scg_sirc_slow_clk), (maximum is 8MHz). #010 3 SCGFIRCLK - Fast IRC Clock(scg_firc_slow_clk), (maximum is 48MHz). #011 6 SCGPCLK System PLL clock(scg_spll_slow_clk). #110 INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_LPUART1 PCC Register 0x1AC 32 read-write 0x80000000 0xFFFFFFFF PCS Peripheral Clock Source Select 24 3 read-write 000 Clock is off (or test clock is enabled). #000 1 OSCCLK - System Oscillator Bus Clock(scg_sosc_slow_clk). #001 2 SCGIRCLK - Slow IRC Clock(scg_sirc_slow_clk), (maximum is 8MHz). #010 3 SCGFIRCLK - Fast IRC Clock(scg_firc_slow_clk), (maximum is 48MHz). #011 6 SCGPCLK System PLL clock(scg_spll_slow_clk). #110 INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_LPUART2 PCC Register 0x1B0 32 read-write 0x80000000 0xFFFFFFFF PCS Peripheral Clock Source Select 24 3 read-write 000 Clock is off (or test clock is enabled). #000 1 OSCCLK - System Oscillator Bus Clock(scg_sosc_slow_clk). #001 2 SCGIRCLK - Slow IRC Clock(scg_sirc_slow_clk), (maximum is 8MHz). #010 3 SCGFIRCLK - Fast IRC Clock(scg_firc_slow_clk), (maximum is 48MHz). #011 6 SCGPCLK System PLL clock(scg_spll_slow_clk). #110 INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_CMP0 PCC Register 0x1CC 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 PCC_CMP1 PCC Register 0x1D0 32 read-write 0x80000000 0xFFFFFFFF INUSE Clock Gate Control 29 1 read-only 0 Peripheral is not being used. #0 1 Peripheral is being used. Software cannot modify the existing clocking configuration. #1 CGC Clock Control 30 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PR Enable 31 1 read-only 0 Peripheral is not present. #0 1 Peripheral is present. #1 LPI2C0 The LPI2C Memory Map/Register Definition can be found here. LPI2C LPI2C0_ 0x40066000 0 0x174 registers LPI2C0 8 VERID Version ID Register 0 32 read-only 0x1000003 0xFFFFFFFF FEATURE Feature Specification Number 0 16 read-only 10 Master only with standard feature set. #10 11 Master and slave with standard feature set. #11 MINOR Minor Version Number 16 8 read-only MAJOR Major Version Number 24 8 read-only PARAM Parameter Register 0x4 32 read-only 0x202 0xFFFFFFFF MTXFIFO Master Transmit FIFO Size 0 4 read-only MRXFIFO Master Receive FIFO Size 8 4 read-only MCR Master Control Register 0x10 32 read-write 0 0xFFFFFFFF MEN Master Enable 0 1 read-write 0 Master logic is disabled. #0 1 Master logic is enabled. #1 RST Software Reset 1 1 read-write 0 Master logic is not reset. #0 1 Master logic is reset. #1 DOZEN Doze mode enable 2 1 read-write 0 Master is enabled in Doze mode. #0 1 Master is disabled in Doze mode. #1 DBGEN Debug Enable 3 1 read-write 0 Master is disabled in debug mode. #0 1 Master is enabled in debug mode. #1 RTF Reset Transmit FIFO 8 1 write-only 0 No effect. #0 1 Transmit FIFO is reset. #1 RRF Reset Receive FIFO 9 1 write-only 0 No effect. #0 1 Receive FIFO is reset. #1 MSR Master Status Register 0x14 32 read-write 0x1 0xFFFFFFFF TDF Transmit Data Flag 0 1 read-only 0 Transmit data not requested. #0 1 Transmit data is requested. #1 RDF Receive Data Flag 1 1 read-only 0 Receive Data is not ready. #0 1 Receive data is ready. #1 EPF End Packet Flag 8 1 read-write 0 Master has not generated a STOP or Repeated START condition. #0 1 Master has generated a STOP or Repeated START condition. #1 SDF STOP Detect Flag 9 1 read-write 0 Master has not generated a STOP condition. #0 1 Master has generated a STOP condition. #1 NDF NACK Detect Flag 10 1 read-write 0 Unexpected NACK not detected. #0 1 Unexpected NACK was detected. #1 ALF Arbitration Lost Flag 11 1 read-write 0 Master has not lost arbitration. #0 1 Master has lost arbitration. #1 FEF FIFO Error Flag 12 1 read-write 0 No error. #0 1 Master sending or receiving data without START condition. #1 PLTF Pin Low Timeout Flag 13 1 read-write 0 Pin low timeout has not occurred or is disabled. #0 1 Pin low timeout has occurred. #1 DMF Data Match Flag 14 1 read-write 0 Have not received matching data. #0 1 Have received matching data. #1 MBF Master Busy Flag 24 1 read-only 0 I2C Master is idle. #0 1 I2C Master is busy. #1 BBF Bus Busy Flag 25 1 read-only 0 I2C Bus is idle. #0 1 I2C Bus is busy. #1 MIER Master Interrupt Enable Register 0x18 32 read-write 0 0xFFFFFFFF TDIE Transmit Data Interrupt Enable 0 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled #1 RDIE Receive Data Interrupt Enable 1 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 EPIE End Packet Interrupt Enable 8 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 SDIE STOP Detect Interrupt Enable 9 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 NDIE NACK Detect Interrupt Enable 10 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 ALIE Arbitration Lost Interrupt Enable 11 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 FEIE FIFO Error Interrupt Enable 12 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 PLTIE Pin Low Timeout Interrupt Enable 13 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 DMIE Data Match Interrupt Enable 14 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 MDER Master DMA Enable Register 0x1C 32 read-write 0 0xFFFFFFFF TDDE Transmit Data DMA Enable 0 1 read-write 0 DMA request disabled. #0 1 DMA request enabled #1 RDDE Receive Data DMA Enable 1 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 MCFGR0 Master Configuration Register 0 0x20 32 read-write 0 0xFFFFFFFF HREN Host Request Enable 0 1 read-write 0 Host request input is disabled. #0 1 Host request input is enabled. #1 HRPOL Host Request Polarity 1 1 read-write 0 Active low. #0 1 Active high. #1 HRSEL Host Request Select 2 1 read-write 0 Host request input is pin LPI2C_HREQ. #0 1 Host request input is input trigger. #1 CIRFIFO Circular FIFO Enable 8 1 read-write 0 Circular FIFO is disabled. #0 1 Circular FIFO is enabled. #1 RDMO Receive Data Match Only 9 1 read-write 0 Received data is stored in the receive FIFO as normal. #0 1 Received data is discarded unless the RMF is set. #1 MCFGR1 Master Configuration Register 1 0x24 32 read-write 0 0xFFFFFFFF PRESCALE Prescaler 0 3 read-write 000 Divide by 1. #000 001 Divide by 2. #001 010 Divide by 4. #010 011 Divide by 8. #011 100 Divide by 16. #100 101 Divide by 32. #101 110 Divide by 64. #110 111 Divide by 128. #111 AUTOSTOP Automatic STOP Generation 8 1 read-write 0 No effect. #0 1 STOP condition is automatically generated whenever the transmit FIFO is empty and LPI2C master is busy. #1 IGNACK When set, the received NACK field is ignored and assumed to be ACK 9 1 read-write 0 LPI2C Master will receive ACK and NACK normally. #0 1 LPI2C Master will treat a received NACK as if it was an ACK. #1 TIMECFG Timeout Configuration 10 1 read-write 0 Pin Low Timeout Flag will set if SCL is low for longer than the configured timeout. #0 1 Pin Low Timeout Flag will set if either SCL or SDA is low for longer than the configured timeout. #1 MATCFG Match Configuration 16 3 read-write 000 Match disabled. #000 010 Match enabled (1st data word equals MATCH0 OR MATCH1). #010 011 Match enabled (any data word equals MATCH0 OR MATCH1). #011 100 Match enabled (1st data word equals MATCH0 AND 2nd data word equals MATCH1). #100 101 Match enabled (any data word equals MATCH0 AND next data word equals MATCH1). #101 110 Match enabled (1st data word AND MATCH1 equals MATCH0 AND MATCH1). #110 111 Match enabled (any data word AND MATCH1 equals MATCH0 AND MATCH1). #111 PINCFG Pin Configuration 24 3 read-write 000 LPI2C configured for 2-pin open drain mode. #000 001 LPI2C configured for 2-pin output only mode (ultra-fast mode). #001 010 LPI2C configured for 2-pin push-pull mode. #010 011 LPI2C configured for 4-pin push-pull mode. #011 100 LPI2C configured for 2-pin open drain mode with separate LPI2C slave. #100 101 LPI2C configured for 2-pin output only mode (ultra-fast mode) with separate LPI2C slave. #101 110 LPI2C configured for 2-pin push-pull mode with separate LPI2C slave. #110 111 LPI2C configured for 4-pin push-pull mode (inverted outputs). #111 MCFGR2 Master Configuration Register 2 0x28 32 read-write 0 0xFFFFFFFF BUSIDLE Bus Idle Timeout 0 12 read-write FILTSCL Glitch Filter SCL 16 4 read-write FILTSDA Glitch Filter SDA 24 4 read-write MCFGR3 Master Configuration Register 3 0x2C 32 read-write 0 0xFFFFFFFF PINLOW Pin Low Timeout 8 12 read-write MDMR Master Data Match Register 0x40 32 read-write 0 0xFFFFFFFF MATCH0 Match 0 Value 0 8 read-write MATCH1 Match 1 Value 16 8 read-write MCCR0 Master Clock Configuration Register 0 0x48 32 read-write 0 0xFFFFFFFF CLKLO Clock Low Period 0 6 read-write CLKHI Clock High Period 8 6 read-write SETHOLD Setup Hold Delay 16 6 read-write DATAVD Data Valid Delay 24 6 read-write MCCR1 Master Clock Configuration Register 1 0x50 32 read-write 0 0xFFFFFFFF CLKLO Clock Low Period 0 6 read-write CLKHI Clock High Period 8 6 read-write SETHOLD Setup Hold Delay 16 6 read-write DATAVD Data Valid Delay 24 6 read-write MFCR Master FIFO Control Register 0x58 32 read-write 0 0xFFFFFFFF TXWATER Transmit FIFO Watermark 0 8 read-write RXWATER Receive FIFO Watermark 16 8 read-write MFSR Master FIFO Status Register 0x5C 32 read-only 0 0xFFFFFFFF TXCOUNT Transmit FIFO Count 0 8 read-only RXCOUNT Receive FIFO Count 16 8 read-only MTDR Master Transmit Data Register 0x60 32 write-only 0 0xFFFFFFFF DATA Transmit Data 0 8 write-only CMD Command Data 8 3 write-only 000 Transmit DATA[7:0]. #000 001 Receive (DATA[7:0] + 1) bytes. #001 010 Generate STOP condition. #010 011 Receive and discard (DATA[7:0] + 1) bytes. #011 100 Generate (repeated) START and transmit address in DATA[7:0]. #100 101 Generate (repeated) START and transmit address in DATA[7:0]. This transfer expects a NACK to be returned. #101 110 Generate (repeated) START and transmit address in DATA[7:0] using high speed mode. #110 111 Generate (repeated) START and transmit address in DATA[7:0] using high speed mode. This transfer expects a NACK to be returned. #111 MRDR Master Receive Data Register 0x70 32 read-only 0x4000 0xFFFFFFFF DATA Receive Data 0 8 read-only RXEMPTY RX Empty 14 1 read-only 0 Receive FIFO is not empty. #0 1 Receive FIFO is empty. #1 SCR Slave Control Register 0x110 32 read-write 0 0xFFFFFFFF SEN Slave Enable 0 1 read-write 0 Slave mode is disabled. #0 1 Slave mode is enabled. #1 RST Software Reset 1 1 read-write 0 Slave logic is not reset. #0 1 Slave logic is reset. #1 FILTEN Filter Enable 4 1 read-write 0 Disable digital filter and output delay counter for slave mode. #0 1 Enable digital filter and output delay counter for slave mode. #1 FILTDZ Filter Doze Enable 5 1 read-write 0 Filter remains enabled in Doze mode. #0 1 Filter is disabled in Doze mode. #1 RTF Reset Transmit FIFO 8 1 write-only 0 No effect. #0 1 Transmit Data Register is now empty. #1 RRF Reset Receive FIFO 9 1 write-only 0 No effect. #0 1 Receive Data Register is now empty. #1 SSR Slave Status Register 0x114 32 read-write 0 0xFFFFFFFF TDF Transmit Data Flag 0 1 read-only 0 Transmit data not requested. #0 1 Transmit data is requested. #1 RDF Receive Data Flag 1 1 read-only 0 Receive Data is not ready. #0 1 Receive data is ready. #1 AVF Address Valid Flag 2 1 read-only 0 Address Status Register is not valid. #0 1 Address Status Register is valid. #1 TAF Transmit ACK Flag 3 1 read-only 0 Transmit ACK/NACK is not required. #0 1 Transmit ACK/NACK is required. #1 RSF Repeated Start Flag 8 1 read-write 0 Slave has not detected a Repeated START condition. #0 1 Slave has detected a Repeated START condition. #1 SDF STOP Detect Flag 9 1 read-write 0 Slave has not detected a STOP condition. #0 1 Slave has detected a STOP condition. #1 BEF Bit Error Flag 10 1 read-write 0 Slave has not detected a bit error. #0 1 Slave has detected a bit error. #1 FEF FIFO Error Flag 11 1 read-write 0 FIFO underflow or overflow not detected. #0 1 FIFO underflow or overflow detected. #1 AM0F Address Match 0 Flag 12 1 read-only 0 Have not received ADDR0 matching address. #0 1 Have received ADDR0 matching address. #1 AM1F Address Match 1 Flag 13 1 read-only 0 Have not received ADDR1 or ADDR0/ADDR1 range matching address. #0 1 Have received ADDR1 or ADDR0/ADDR1 range matching address. #1 GCF General Call Flag 14 1 read-only 0 Slave has not detected the General Call Address or General Call Address disabled. #0 1 Slave has detected the General Call Address. #1 SARF SMBus Alert Response Flag 15 1 read-only 0 SMBus Alert Response disabled or not detected. #0 1 SMBus Alert Response enabled and detected. #1 SBF Slave Busy Flag 24 1 read-only 0 I2C Slave is idle. #0 1 I2C Slave is busy. #1 BBF Bus Busy Flag 25 1 read-only 0 I2C Bus is idle. #0 1 I2C Bus is busy. #1 SIER Slave Interrupt Enable Register 0x118 32 read-write 0 0xFFFFFFFF TDIE Transmit Data Interrupt Enable 0 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled #1 RDIE Receive Data Interrupt Enable 1 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 AVIE Address Valid Interrupt Enable 2 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 TAIE Transmit ACK Interrupt Enable 3 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 RSIE Repeated Start Interrupt Enable 8 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 SDIE STOP Detect Interrupt Enable 9 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 BEIE Bit Error Interrupt Enable 10 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 FEIE FIFO Error Interrupt Enable 11 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 AM0IE Address Match 0 Interrupt Enable 12 1 read-write 0 Interrupt enabled. #0 1 Interrupt disabled. #1 AM1F Address Match 1 Interrupt Enable 13 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 GCIE General Call Interrupt Enable 14 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 SARIE SMBus Alert Response Interrupt Enable 15 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 SDER Slave DMA Enable Register 0x11C 32 read-write 0 0xFFFFFFFF TDDE Transmit Data DMA Enable 0 1 read-write 0 DMA request disabled. #0 1 DMA request enabled #1 RDDE Receive Data DMA Enable 1 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 AVDE Address Valid DMA Enable 2 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 SCFGR1 Slave Configuration Register 1 0x124 32 read-write 0 0xFFFFFFFF ADRSTALL Address SCL Stall 0 1 read-write 0 Clock stretching disabled. #0 1 Clock stretching enabled. #1 RXSTALL RX SCL Stall 1 1 read-write 0 Clock stretching disabled. #0 1 Clock stretching enabled. #1 TXDSTALL TX Data SCL Stall 2 1 read-write 0 Clock stretching disabled. #0 1 Clock stretching enabled. #1 ACKSTALL ACK SCL Stall 3 1 read-write 0 Clock stretching disabled. #0 1 Clock stretching enabled. #1 GCEN General Call Enable 8 1 read-write 0 General Call address is disabled. #0 1 General call address is enabled. #1 SAEN SMBus Alert Enable 9 1 read-write 0 Disables match on SMBus Alert. #0 1 Enables match on SMBus Alert. #1 TXCFG Transmit Flag Configuration 10 1 read-write 0 Transmit Data Flag will only assert during a slave-transmit transfer when the transmit data register is empty. #0 1 Transmit Data Flag will assert whenever the transmit data register is empty. #1 RXCFG Receive Data Configuration 11 1 read-write 0 Reading the receive data register will return receive data and clear the receive data flag. #0 1 Reading the receive data register when the address valid flag is set will return the address status register and clear the address valid flag. Reading the receive data register when the address valid flag is clear will return receive data and clear the receive data flag. #1 IGNACK Ignore NACK 12 1 read-write 0 Slave will end transfer when NACK detected. #0 1 Slave will not end transfer when NACK detected. #1 HSMEN High Speed Mode Enable 13 1 read-write 0 Disables detection of Hs-mode master code. #0 1 Enables detection of Hs-mode master code. #1 ADDRCFG Address Configuration 16 3 read-write 000 Address match 0 (7-bit). #000 001 Address match 0 (10-bit). #001 010 Address match 0 (7-bit) or Address match 1 (7-bit). #010 011 Address match 0 (10-bit) or Address match 1 (10-bit). #011 100 Address match 0 (7-bit) or Address match 1 (10-bit). #100 101 Address match 0 (10-bit) or Address match 1 (7-bit). #101 110 From Address match 0 (7-bit) to Address match 1 (7-bit). #110 111 From Address match 0 (10-bit) to Address match 1 (10-bit). #111 SCFGR2 Slave Configuration Register 2 0x128 32 read-write 0 0xFFFFFFFF CLKHOLD Clock Hold Time 0 4 read-write DATAVD Data Valid Delay 8 6 read-write FILTSCL Glitch Filter SCL 16 4 read-write FILTSDA Glitch Filter SDA 24 4 read-write SAMR Slave Address Match Register 0x140 32 read-write 0 0xFFFFFFFF ADDR0 Address 0 Value 1 10 read-write ADDR1 Address 1 Value 17 10 read-write SASR Slave Address Status Register 0x150 32 read-only 0x4000 0xFFFFFFFF RADDR Received Address 0 11 read-only ANV Address Not Valid 14 1 read-only 0 RADDR is valid. #0 1 RADDR is not valid. #1 STAR Slave Transmit ACK Register 0x154 32 read-write 0 0xFFFFFFFF TXNACK Transmit NACK 0 1 read-write 0 Transmit ACK for received word. #0 1 Transmit NACK for received word. #1 STDR Slave Transmit Data Register 0x160 32 write-only 0 0xFFFFFFFF DATA Transmit Data 0 8 write-only SRDR Slave Receive Data Register 0x170 32 read-only 0x4000 0xFFFFFFFF DATA Receive Data 0 8 read-only RXEMPTY RX Empty 14 1 read-only 0 The Receive Data Register is not empty. #0 1 The Receive Data Register is empty. #1 SOF Start Of Frame 15 1 read-only 0 Indicates this is not the first data word since a (repeated) START or STOP condition. #0 1 Indicates this is the first data word since a (repeated) START or STOP condition. #1 LPI2C1 The LPI2C Memory Map/Register Definition can be found here. LPI2C LPI2C1_ 0x40067000 0 0x174 registers LPI2C1 9 VERID Version ID Register 0 32 read-only 0x1000003 0xFFFFFFFF FEATURE Feature Specification Number 0 16 read-only 10 Master only with standard feature set. #10 11 Master and slave with standard feature set. #11 MINOR Minor Version Number 16 8 read-only MAJOR Major Version Number 24 8 read-only PARAM Parameter Register 0x4 32 read-only 0x202 0xFFFFFFFF MTXFIFO Master Transmit FIFO Size 0 4 read-only MRXFIFO Master Receive FIFO Size 8 4 read-only MCR Master Control Register 0x10 32 read-write 0 0xFFFFFFFF MEN Master Enable 0 1 read-write 0 Master logic is disabled. #0 1 Master logic is enabled. #1 RST Software Reset 1 1 read-write 0 Master logic is not reset. #0 1 Master logic is reset. #1 DOZEN Doze mode enable 2 1 read-write 0 Master is enabled in Doze mode. #0 1 Master is disabled in Doze mode. #1 DBGEN Debug Enable 3 1 read-write 0 Master is disabled in debug mode. #0 1 Master is enabled in debug mode. #1 RTF Reset Transmit FIFO 8 1 write-only 0 No effect. #0 1 Transmit FIFO is reset. #1 RRF Reset Receive FIFO 9 1 write-only 0 No effect. #0 1 Receive FIFO is reset. #1 MSR Master Status Register 0x14 32 read-write 0x1 0xFFFFFFFF TDF Transmit Data Flag 0 1 read-only 0 Transmit data not requested. #0 1 Transmit data is requested. #1 RDF Receive Data Flag 1 1 read-only 0 Receive Data is not ready. #0 1 Receive data is ready. #1 EPF End Packet Flag 8 1 read-write 0 Master has not generated a STOP or Repeated START condition. #0 1 Master has generated a STOP or Repeated START condition. #1 SDF STOP Detect Flag 9 1 read-write 0 Master has not generated a STOP condition. #0 1 Master has generated a STOP condition. #1 NDF NACK Detect Flag 10 1 read-write 0 Unexpected NACK not detected. #0 1 Unexpected NACK was detected. #1 ALF Arbitration Lost Flag 11 1 read-write 0 Master has not lost arbitration. #0 1 Master has lost arbitration. #1 FEF FIFO Error Flag 12 1 read-write 0 No error. #0 1 Master sending or receiving data without START condition. #1 PLTF Pin Low Timeout Flag 13 1 read-write 0 Pin low timeout has not occurred or is disabled. #0 1 Pin low timeout has occurred. #1 DMF Data Match Flag 14 1 read-write 0 Have not received matching data. #0 1 Have received matching data. #1 MBF Master Busy Flag 24 1 read-only 0 I2C Master is idle. #0 1 I2C Master is busy. #1 BBF Bus Busy Flag 25 1 read-only 0 I2C Bus is idle. #0 1 I2C Bus is busy. #1 MIER Master Interrupt Enable Register 0x18 32 read-write 0 0xFFFFFFFF TDIE Transmit Data Interrupt Enable 0 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled #1 RDIE Receive Data Interrupt Enable 1 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 EPIE End Packet Interrupt Enable 8 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 SDIE STOP Detect Interrupt Enable 9 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 NDIE NACK Detect Interrupt Enable 10 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 ALIE Arbitration Lost Interrupt Enable 11 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 FEIE FIFO Error Interrupt Enable 12 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 PLTIE Pin Low Timeout Interrupt Enable 13 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 DMIE Data Match Interrupt Enable 14 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 MDER Master DMA Enable Register 0x1C 32 read-write 0 0xFFFFFFFF TDDE Transmit Data DMA Enable 0 1 read-write 0 DMA request disabled. #0 1 DMA request enabled #1 RDDE Receive Data DMA Enable 1 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 MCFGR0 Master Configuration Register 0 0x20 32 read-write 0 0xFFFFFFFF HREN Host Request Enable 0 1 read-write 0 Host request input is disabled. #0 1 Host request input is enabled. #1 HRPOL Host Request Polarity 1 1 read-write 0 Active low. #0 1 Active high. #1 HRSEL Host Request Select 2 1 read-write 0 Host request input is pin LPI2C_HREQ. #0 1 Host request input is input trigger. #1 CIRFIFO Circular FIFO Enable 8 1 read-write 0 Circular FIFO is disabled. #0 1 Circular FIFO is enabled. #1 RDMO Receive Data Match Only 9 1 read-write 0 Received data is stored in the receive FIFO as normal. #0 1 Received data is discarded unless the RMF is set. #1 MCFGR1 Master Configuration Register 1 0x24 32 read-write 0 0xFFFFFFFF PRESCALE Prescaler 0 3 read-write 000 Divide by 1. #000 001 Divide by 2. #001 010 Divide by 4. #010 011 Divide by 8. #011 100 Divide by 16. #100 101 Divide by 32. #101 110 Divide by 64. #110 111 Divide by 128. #111 AUTOSTOP Automatic STOP Generation 8 1 read-write 0 No effect. #0 1 STOP condition is automatically generated whenever the transmit FIFO is empty and LPI2C master is busy. #1 IGNACK When set, the received NACK field is ignored and assumed to be ACK 9 1 read-write 0 LPI2C Master will receive ACK and NACK normally. #0 1 LPI2C Master will treat a received NACK as if it was an ACK. #1 TIMECFG Timeout Configuration 10 1 read-write 0 Pin Low Timeout Flag will set if SCL is low for longer than the configured timeout. #0 1 Pin Low Timeout Flag will set if either SCL or SDA is low for longer than the configured timeout. #1 MATCFG Match Configuration 16 3 read-write 000 Match disabled. #000 010 Match enabled (1st data word equals MATCH0 OR MATCH1). #010 011 Match enabled (any data word equals MATCH0 OR MATCH1). #011 100 Match enabled (1st data word equals MATCH0 AND 2nd data word equals MATCH1). #100 101 Match enabled (any data word equals MATCH0 AND next data word equals MATCH1). #101 110 Match enabled (1st data word AND MATCH1 equals MATCH0 AND MATCH1). #110 111 Match enabled (any data word AND MATCH1 equals MATCH0 AND MATCH1). #111 PINCFG Pin Configuration 24 3 read-write 000 LPI2C configured for 2-pin open drain mode. #000 001 LPI2C configured for 2-pin output only mode (ultra-fast mode). #001 010 LPI2C configured for 2-pin push-pull mode. #010 011 LPI2C configured for 4-pin push-pull mode. #011 100 LPI2C configured for 2-pin open drain mode with separate LPI2C slave. #100 101 LPI2C configured for 2-pin output only mode (ultra-fast mode) with separate LPI2C slave. #101 110 LPI2C configured for 2-pin push-pull mode with separate LPI2C slave. #110 111 LPI2C configured for 4-pin push-pull mode (inverted outputs). #111 MCFGR2 Master Configuration Register 2 0x28 32 read-write 0 0xFFFFFFFF BUSIDLE Bus Idle Timeout 0 12 read-write FILTSCL Glitch Filter SCL 16 4 read-write FILTSDA Glitch Filter SDA 24 4 read-write MCFGR3 Master Configuration Register 3 0x2C 32 read-write 0 0xFFFFFFFF PINLOW Pin Low Timeout 8 12 read-write MDMR Master Data Match Register 0x40 32 read-write 0 0xFFFFFFFF MATCH0 Match 0 Value 0 8 read-write MATCH1 Match 1 Value 16 8 read-write MCCR0 Master Clock Configuration Register 0 0x48 32 read-write 0 0xFFFFFFFF CLKLO Clock Low Period 0 6 read-write CLKHI Clock High Period 8 6 read-write SETHOLD Setup Hold Delay 16 6 read-write DATAVD Data Valid Delay 24 6 read-write MCCR1 Master Clock Configuration Register 1 0x50 32 read-write 0 0xFFFFFFFF CLKLO Clock Low Period 0 6 read-write CLKHI Clock High Period 8 6 read-write SETHOLD Setup Hold Delay 16 6 read-write DATAVD Data Valid Delay 24 6 read-write MFCR Master FIFO Control Register 0x58 32 read-write 0 0xFFFFFFFF TXWATER Transmit FIFO Watermark 0 8 read-write RXWATER Receive FIFO Watermark 16 8 read-write MFSR Master FIFO Status Register 0x5C 32 read-only 0 0xFFFFFFFF TXCOUNT Transmit FIFO Count 0 8 read-only RXCOUNT Receive FIFO Count 16 8 read-only MTDR Master Transmit Data Register 0x60 32 write-only 0 0xFFFFFFFF DATA Transmit Data 0 8 write-only CMD Command Data 8 3 write-only 000 Transmit DATA[7:0]. #000 001 Receive (DATA[7:0] + 1) bytes. #001 010 Generate STOP condition. #010 011 Receive and discard (DATA[7:0] + 1) bytes. #011 100 Generate (repeated) START and transmit address in DATA[7:0]. #100 101 Generate (repeated) START and transmit address in DATA[7:0]. This transfer expects a NACK to be returned. #101 110 Generate (repeated) START and transmit address in DATA[7:0] using high speed mode. #110 111 Generate (repeated) START and transmit address in DATA[7:0] using high speed mode. This transfer expects a NACK to be returned. #111 MRDR Master Receive Data Register 0x70 32 read-only 0x4000 0xFFFFFFFF DATA Receive Data 0 8 read-only RXEMPTY RX Empty 14 1 read-only 0 Receive FIFO is not empty. #0 1 Receive FIFO is empty. #1 SCR Slave Control Register 0x110 32 read-write 0 0xFFFFFFFF SEN Slave Enable 0 1 read-write 0 Slave mode is disabled. #0 1 Slave mode is enabled. #1 RST Software Reset 1 1 read-write 0 Slave logic is not reset. #0 1 Slave logic is reset. #1 FILTEN Filter Enable 4 1 read-write 0 Disable digital filter and output delay counter for slave mode. #0 1 Enable digital filter and output delay counter for slave mode. #1 FILTDZ Filter Doze Enable 5 1 read-write 0 Filter remains enabled in Doze mode. #0 1 Filter is disabled in Doze mode. #1 RTF Reset Transmit FIFO 8 1 write-only 0 No effect. #0 1 Transmit Data Register is now empty. #1 RRF Reset Receive FIFO 9 1 write-only 0 No effect. #0 1 Receive Data Register is now empty. #1 SSR Slave Status Register 0x114 32 read-write 0 0xFFFFFFFF TDF Transmit Data Flag 0 1 read-only 0 Transmit data not requested. #0 1 Transmit data is requested. #1 RDF Receive Data Flag 1 1 read-only 0 Receive Data is not ready. #0 1 Receive data is ready. #1 AVF Address Valid Flag 2 1 read-only 0 Address Status Register is not valid. #0 1 Address Status Register is valid. #1 TAF Transmit ACK Flag 3 1 read-only 0 Transmit ACK/NACK is not required. #0 1 Transmit ACK/NACK is required. #1 RSF Repeated Start Flag 8 1 read-write 0 Slave has not detected a Repeated START condition. #0 1 Slave has detected a Repeated START condition. #1 SDF STOP Detect Flag 9 1 read-write 0 Slave has not detected a STOP condition. #0 1 Slave has detected a STOP condition. #1 BEF Bit Error Flag 10 1 read-write 0 Slave has not detected a bit error. #0 1 Slave has detected a bit error. #1 FEF FIFO Error Flag 11 1 read-write 0 FIFO underflow or overflow not detected. #0 1 FIFO underflow or overflow detected. #1 AM0F Address Match 0 Flag 12 1 read-only 0 Have not received ADDR0 matching address. #0 1 Have received ADDR0 matching address. #1 AM1F Address Match 1 Flag 13 1 read-only 0 Have not received ADDR1 or ADDR0/ADDR1 range matching address. #0 1 Have received ADDR1 or ADDR0/ADDR1 range matching address. #1 GCF General Call Flag 14 1 read-only 0 Slave has not detected the General Call Address or General Call Address disabled. #0 1 Slave has detected the General Call Address. #1 SARF SMBus Alert Response Flag 15 1 read-only 0 SMBus Alert Response disabled or not detected. #0 1 SMBus Alert Response enabled and detected. #1 SBF Slave Busy Flag 24 1 read-only 0 I2C Slave is idle. #0 1 I2C Slave is busy. #1 BBF Bus Busy Flag 25 1 read-only 0 I2C Bus is idle. #0 1 I2C Bus is busy. #1 SIER Slave Interrupt Enable Register 0x118 32 read-write 0 0xFFFFFFFF TDIE Transmit Data Interrupt Enable 0 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled #1 RDIE Receive Data Interrupt Enable 1 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 AVIE Address Valid Interrupt Enable 2 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 TAIE Transmit ACK Interrupt Enable 3 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 RSIE Repeated Start Interrupt Enable 8 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 SDIE STOP Detect Interrupt Enable 9 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 BEIE Bit Error Interrupt Enable 10 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 FEIE FIFO Error Interrupt Enable 11 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 AM0IE Address Match 0 Interrupt Enable 12 1 read-write 0 Interrupt enabled. #0 1 Interrupt disabled. #1 AM1F Address Match 1 Interrupt Enable 13 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 GCIE General Call Interrupt Enable 14 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 SARIE SMBus Alert Response Interrupt Enable 15 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 SDER Slave DMA Enable Register 0x11C 32 read-write 0 0xFFFFFFFF TDDE Transmit Data DMA Enable 0 1 read-write 0 DMA request disabled. #0 1 DMA request enabled #1 RDDE Receive Data DMA Enable 1 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 AVDE Address Valid DMA Enable 2 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 SCFGR1 Slave Configuration Register 1 0x124 32 read-write 0 0xFFFFFFFF ADRSTALL Address SCL Stall 0 1 read-write 0 Clock stretching disabled. #0 1 Clock stretching enabled. #1 RXSTALL RX SCL Stall 1 1 read-write 0 Clock stretching disabled. #0 1 Clock stretching enabled. #1 TXDSTALL TX Data SCL Stall 2 1 read-write 0 Clock stretching disabled. #0 1 Clock stretching enabled. #1 ACKSTALL ACK SCL Stall 3 1 read-write 0 Clock stretching disabled. #0 1 Clock stretching enabled. #1 GCEN General Call Enable 8 1 read-write 0 General Call address is disabled. #0 1 General call address is enabled. #1 SAEN SMBus Alert Enable 9 1 read-write 0 Disables match on SMBus Alert. #0 1 Enables match on SMBus Alert. #1 TXCFG Transmit Flag Configuration 10 1 read-write 0 Transmit Data Flag will only assert during a slave-transmit transfer when the transmit data register is empty. #0 1 Transmit Data Flag will assert whenever the transmit data register is empty. #1 RXCFG Receive Data Configuration 11 1 read-write 0 Reading the receive data register will return receive data and clear the receive data flag. #0 1 Reading the receive data register when the address valid flag is set will return the address status register and clear the address valid flag. Reading the receive data register when the address valid flag is clear will return receive data and clear the receive data flag. #1 IGNACK Ignore NACK 12 1 read-write 0 Slave will end transfer when NACK detected. #0 1 Slave will not end transfer when NACK detected. #1 HSMEN High Speed Mode Enable 13 1 read-write 0 Disables detection of Hs-mode master code. #0 1 Enables detection of Hs-mode master code. #1 ADDRCFG Address Configuration 16 3 read-write 000 Address match 0 (7-bit). #000 001 Address match 0 (10-bit). #001 010 Address match 0 (7-bit) or Address match 1 (7-bit). #010 011 Address match 0 (10-bit) or Address match 1 (10-bit). #011 100 Address match 0 (7-bit) or Address match 1 (10-bit). #100 101 Address match 0 (10-bit) or Address match 1 (7-bit). #101 110 From Address match 0 (7-bit) to Address match 1 (7-bit). #110 111 From Address match 0 (10-bit) to Address match 1 (10-bit). #111 SCFGR2 Slave Configuration Register 2 0x128 32 read-write 0 0xFFFFFFFF CLKHOLD Clock Hold Time 0 4 read-write DATAVD Data Valid Delay 8 6 read-write FILTSCL Glitch Filter SCL 16 4 read-write FILTSDA Glitch Filter SDA 24 4 read-write SAMR Slave Address Match Register 0x140 32 read-write 0 0xFFFFFFFF ADDR0 Address 0 Value 1 10 read-write ADDR1 Address 1 Value 17 10 read-write SASR Slave Address Status Register 0x150 32 read-only 0x4000 0xFFFFFFFF RADDR Received Address 0 11 read-only ANV Address Not Valid 14 1 read-only 0 RADDR is valid. #0 1 RADDR is not valid. #1 STAR Slave Transmit ACK Register 0x154 32 read-write 0 0xFFFFFFFF TXNACK Transmit NACK 0 1 read-write 0 Transmit ACK for received word. #0 1 Transmit NACK for received word. #1 STDR Slave Transmit Data Register 0x160 32 write-only 0 0xFFFFFFFF DATA Transmit Data 0 8 write-only SRDR Slave Receive Data Register 0x170 32 read-only 0x4000 0xFFFFFFFF DATA Receive Data 0 8 read-only RXEMPTY RX Empty 14 1 read-only 0 The Receive Data Register is not empty. #0 1 The Receive Data Register is empty. #1 SOF Start Of Frame 15 1 read-only 0 Indicates this is not the first data word since a (repeated) START or STOP condition. #0 1 Indicates this is the first data word since a (repeated) START or STOP condition. #1 LPUART0 LPUART LPUART 0x4006A000 0 0x30 registers LPUART0 12 VERID Version ID Register 0 32 read-only 0x4010003 0xFFFFFFFF FEATURE Feature Identification Number 0 16 read-only 0x1 Standard feature set. #1 0x3 Standard feature set with MODEM/IrDA support. #11 MINOR Minor Version Number 16 8 read-only MAJOR Major Version Number 24 8 read-only PARAM Parameter Register 0x4 32 read-only 0x202 0xFFFFFFFF TXFIFO Transmit FIFO Size 0 8 read-only RXFIFO Receive FIFO Size 8 8 read-only GLOBAL LPUART Global Register 0x8 32 read-write 0 0xFFFFFFFF RST Software Reset 1 1 read-write 0 Module is not reset. #0 1 Module is reset. #1 PINCFG LPUART Pin Configuration Register 0xC 32 read-write 0 0xFFFFFFFF TRGSEL Trigger Select 0 2 read-write 00 Input trigger is disabled. #00 01 Input trigger is used instead of RXD pin input. #01 10 Input trigger is used instead of CTS_B pin input. #10 11 Input trigger is used to modulate the TXD pin output. #11 BAUD LPUART Baud Rate Register 0x10 32 read-write 0xF000004 0xFFFFFFFF SBR Baud Rate Modulo Divisor. 0 13 read-write SBNS Stop Bit Number Select 13 1 read-write 0 One stop bit. #0 1 Two stop bits. #1 RXEDGIE RX Input Active Edge Interrupt Enable 14 1 read-write 0 Hardware interrupts from LPUART_STAT[RXEDGIF] disabled (use polling). #0 1 Hardware interrupt requested when LPUART_STAT[RXEDGIF] flag is 1. #1 LBKDIE LIN Break Detect Interrupt Enable 15 1 read-write 0 Hardware interrupts from LPUART_STAT[LBKDIF] disabled (use polling). #0 1 Hardware interrupt requested when LPUART_STAT[LBKDIF] flag is 1. #1 RESYNCDIS Resynchronization Disable 16 1 read-write 0 Resynchronization during received data word is supported #0 1 Resynchronization during received data word is disabled #1 BOTHEDGE Both Edge Sampling 17 1 read-write 0 Receiver samples input data using the rising edge of the baud rate clock. #0 1 Receiver samples input data using the rising and falling edge of the baud rate clock. #1 MATCFG Match Configuration 18 2 read-write 00 Address Match Wakeup #00 01 Idle Match Wakeup #01 10 Match On and Match Off #10 RIDMAE Receiver Idle DMA Enable 20 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 RDMAE Receiver Full DMA Enable 21 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 TDMAE Transmitter DMA Enable 23 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 OSR Oversampling Ratio 24 5 read-write M10 10-bit Mode select 29 1 read-write 0 Receiver and transmitter use 7-bit to 9-bit data characters. #0 1 Receiver and transmitter use 10-bit data characters. #1 MAEN2 Match Address Mode Enable 2 30 1 read-write 0 Normal operation. #0 1 Enables automatic address matching or data matching mode for MATCH[MA2]. #1 MAEN1 Match Address Mode Enable 1 31 1 read-write 0 Normal operation. #0 1 Enables automatic address matching or data matching mode for MATCH[MA1]. #1 STAT LPUART Status Register 0x14 32 read-write 0xC00000 0xFFFFFFFF MA2F Match 2 Flag 14 1 read-write 0 Received data is not equal to MA2 #0 1 Received data is equal to MA2 #1 MA1F Match 1 Flag 15 1 read-write 0 Received data is not equal to MA1 #0 1 Received data is equal to MA1 #1 PF Parity Error Flag 16 1 read-write 0 No parity error. #0 1 Parity error. #1 FE Framing Error Flag 17 1 read-write 0 No framing error detected. This does not guarantee the framing is correct. #0 1 Framing error. #1 NF Noise Flag 18 1 read-write 0 No noise detected. #0 1 Noise detected in the received character in LPUART_DATA. #1 OR Receiver Overrun Flag 19 1 read-write 0 No overrun. #0 1 Receive overrun (new LPUART data lost). #1 IDLE Idle Line Flag 20 1 read-write 0 No idle line detected. #0 1 Idle line was detected. #1 RDRF Receive Data Register Full Flag 21 1 read-only 0 Receive data buffer empty. #0 1 Receive data buffer full. #1 TC Transmission Complete Flag 22 1 read-only 0 Transmitter active (sending data, a preamble, or a break). #0 1 Transmitter idle (transmission activity complete). #1 TDRE Transmit Data Register Empty Flag 23 1 read-only 0 Transmit data buffer full. #0 1 Transmit data buffer empty. #1 RAF Receiver Active Flag 24 1 read-only 0 LPUART receiver idle waiting for a start bit. #0 1 LPUART receiver active (RXD input not idle). #1 LBKDE LIN Break Detection Enable 25 1 read-write 0 LIN break detect is disabled, normal break character can be detected. #0 1 LIN break detect is enabled. LIN break character is detected at length of 11 bit times (if M = 0) or 12 (if M = 1) or 13 (M10 = 1). #1 BRK13 Break Character Generation Length 26 1 read-write 0 Break character is transmitted with length of 9 to 13 bit times. #0 1 Break character is transmitted with length of 12 to 15 bit times. #1 RWUID Receive Wake Up Idle Detect 27 1 read-write 0 During receive standby state (RWU = 1), the IDLE bit does not get set upon detection of an idle character. During address match wakeup, the IDLE bit does not get set when an address does not match. #0 1 During receive standby state (RWU = 1), the IDLE bit gets set upon detection of an idle character. During address match wakeup, the IDLE bit does get set when an address does not match. #1 RXINV Receive Data Inversion 28 1 read-write 0 Receive data not inverted. #0 1 Receive data inverted. #1 MSBF MSB First 29 1 read-write 0 LSB (bit0) is the first bit that is transmitted following the start bit. Further, the first bit received after the start bit is identified as bit0. #0 1 MSB (bit9, bit8, bit7 or bit6) is the first bit that is transmitted following the start bit depending on the setting of CTRL[M], CTRL[PE] and BAUD[M10]. Further, the first bit received after the start bit is identified as bit9, bit8, bit7 or bit6 depending on the setting of CTRL[M] and CTRL[PE]. #1 RXEDGIF RXD Pin Active Edge Interrupt Flag 30 1 read-write 0 No active edge on the receive pin has occurred. #0 1 An active edge on the receive pin has occurred. #1 LBKDIF LIN Break Detect Interrupt Flag 31 1 read-write 0 No LIN break character has been detected. #0 1 LIN break character has been detected. #1 CTRL LPUART Control Register 0x18 32 read-write 0 0xFFFFFFFF PT Parity Type 0 1 read-write 0 Even parity. #0 1 Odd parity. #1 PE Parity Enable 1 1 read-write 0 No hardware parity generation or checking. #0 1 Parity enabled. #1 ILT Idle Line Type Select 2 1 read-write 0 Idle character bit count starts after start bit. #0 1 Idle character bit count starts after stop bit. #1 WAKE Receiver Wakeup Method Select 3 1 read-write 0 Configures RWU for idle-line wakeup. #0 1 Configures RWU with address-mark wakeup. #1 M 9-Bit or 8-Bit Mode Select 4 1 read-write 0 Receiver and transmitter use 8-bit data characters. #0 1 Receiver and transmitter use 9-bit data characters. #1 RSRC Receiver Source Select 5 1 read-write 0 Provided LOOPS is set, RSRC is cleared, selects internal loop back mode and the LPUART does not use the RXD pin. #0 1 Single-wire LPUART mode where the TXD pin is connected to the transmitter output and receiver input. #1 DOZEEN Doze Enable 6 1 read-write 0 LPUART is enabled in Doze mode. #0 1 LPUART is disabled in Doze mode. #1 LOOPS Loop Mode Select 7 1 read-write 0 Normal operation - RXD and TXD use separate pins. #0 1 Loop mode or single-wire mode where transmitter outputs are internally connected to receiver input (see RSRC bit). #1 IDLECFG Idle Configuration 8 3 read-write 000 1 idle character #000 001 2 idle characters #001 010 4 idle characters #010 011 8 idle characters #011 100 16 idle characters #100 101 32 idle characters #101 110 64 idle characters #110 111 128 idle characters #111 M7 7-Bit Mode Select 11 1 read-write 0 Receiver and transmitter use 8-bit to 10-bit data characters. #0 1 Receiver and transmitter use 7-bit data characters. #1 MA2IE Match 2 Interrupt Enable 14 1 read-write 0 MA2F interrupt disabled #0 1 MA2F interrupt enabled #1 MA1IE Match 1 Interrupt Enable 15 1 read-write 0 MA1F interrupt disabled #0 1 MA1F interrupt enabled #1 SBK Send Break 16 1 read-write 0 Normal transmitter operation. #0 1 Queue break character(s) to be sent. #1 RWU Receiver Wakeup Control 17 1 read-write 0 Normal receiver operation. #0 1 LPUART receiver in standby waiting for wakeup condition. #1 RE Receiver Enable 18 1 read-write 0 Receiver disabled. #0 1 Receiver enabled. #1 TE Transmitter Enable 19 1 read-write 0 Transmitter disabled. #0 1 Transmitter enabled. #1 ILIE Idle Line Interrupt Enable 20 1 read-write 0 Hardware interrupts from IDLE disabled; use polling. #0 1 Hardware interrupt requested when IDLE flag is 1. #1 RIE Receiver Interrupt Enable 21 1 read-write 0 Hardware interrupts from RDRF disabled; use polling. #0 1 Hardware interrupt requested when RDRF flag is 1. #1 TCIE Transmission Complete Interrupt Enable for 22 1 read-write 0 Hardware interrupts from TC disabled; use polling. #0 1 Hardware interrupt requested when TC flag is 1. #1 TIE Transmit Interrupt Enable 23 1 read-write 0 Hardware interrupts from TDRE disabled; use polling. #0 1 Hardware interrupt requested when TDRE flag is 1. #1 PEIE Parity Error Interrupt Enable 24 1 read-write 0 PF interrupts disabled; use polling). #0 1 Hardware interrupt requested when PF is set. #1 FEIE Framing Error Interrupt Enable 25 1 read-write 0 FE interrupts disabled; use polling. #0 1 Hardware interrupt requested when FE is set. #1 NEIE Noise Error Interrupt Enable 26 1 read-write 0 NF interrupts disabled; use polling. #0 1 Hardware interrupt requested when NF is set. #1 ORIE Overrun Interrupt Enable 27 1 read-write 0 OR interrupts disabled; use polling. #0 1 Hardware interrupt requested when OR is set. #1 TXINV Transmit Data Inversion 28 1 read-write 0 Transmit data not inverted. #0 1 Transmit data inverted. #1 TXDIR TXD Pin Direction in Single-Wire Mode 29 1 read-write 0 TXD pin is an input in single-wire mode. #0 1 TXD pin is an output in single-wire mode. #1 R9T8 Receive Bit 9 / Transmit Bit 8 30 1 read-write R8T9 Receive Bit 8 / Transmit Bit 9 31 1 read-write DATA LPUART Data Register 0x1C 32 read-write 0x1000 0xFFFFFFFF R0T0 R0T0 0 1 read-write R1T1 R1T1 1 1 read-write R2T2 R2T2 2 1 read-write R3T3 R3T3 3 1 read-write R4T4 R4T4 4 1 read-write R5T5 R5T5 5 1 read-write R6T6 R6T6 6 1 read-write R7T7 R7T7 7 1 read-write R8T8 R8T8 8 1 read-write R9T9 R9T9 9 1 read-write IDLINE Idle Line 11 1 read-only 0 Receiver was not idle before receiving this character. #0 1 Receiver was idle before receiving this character. #1 RXEMPT Receive Buffer Empty 12 1 read-only 0 Receive buffer contains valid data. #0 1 Receive buffer is empty, data returned on read is not valid. #1 FRETSC Frame Error / Transmit Special Character 13 1 read-write 0 The dataword was received without a frame error on read, transmit a normal character on write. #0 1 The dataword was received with a frame error, transmit an idle or break character on transmit. #1 PARITYE PARITYE 14 1 read-only 0 The dataword was received without a parity error. #0 1 The dataword was received with a parity error. #1 NOISY NOISY 15 1 read-only 0 The dataword was received without noise. #0 1 The data was received with noise. #1 MATCH LPUART Match Address Register 0x20 32 read-write 0 0xFFFFFFFF MA1 Match Address 1 0 10 read-write MA2 Match Address 2 16 10 read-write MODIR LPUART Modem IrDA Register 0x24 32 read-write 0 0xFFFFFFFF TXCTSE Transmitter clear-to-send enable 0 1 read-write 0 CTS has no effect on the transmitter. #0 1 Enables clear-to-send operation. The transmitter checks the state of CTS each time it is ready to send a character. If CTS is asserted, the character is sent. If CTS is deasserted, the signal TXD remains in the mark state and transmission is delayed until CTS is asserted. Changes in CTS as a character is being sent do not affect its transmission. #1 TXRTSE Transmitter request-to-send enable 1 1 read-write 0 The transmitter has no effect on RTS. #0 1 When a character is placed into an empty transmitter data buffer , RTS asserts one bit time before the start bit is transmitted. RTS deasserts one bit time after all characters in the transmitter data buffer and shift register are completely sent, including the last stop bit. #1 TXRTSPOL Transmitter request-to-send polarity 2 1 read-write 0 Transmitter RTS is active low. #0 1 Transmitter RTS is active high. #1 RXRTSE Receiver request-to-send enable 3 1 read-write 0 The receiver has no effect on RTS. #0 TXCTSC Transmit CTS Configuration 4 1 read-write 0 CTS input is sampled at the start of each character. #0 1 CTS input is sampled when the transmitter is idle. #1 TXCTSSRC Transmit CTS Source 5 1 read-write 0 CTS input is the CTS_B pin. #0 1 CTS input is the inverted Receiver Match result. #1 RTSWATER Receive RTS Configuration 8 8 read-write TNP Transmitter narrow pulse 16 2 read-write 00 1/OSR. #00 01 2/OSR. #01 10 3/OSR. #10 11 4/OSR. #11 IREN Infrared enable 18 1 read-write 0 IR disabled. #0 1 IR enabled. #1 FIFO LPUART FIFO Register 0x28 32 read-write 0xC00011 0xFFFFFFFF RXFIFOSIZE Receive FIFO. Buffer Depth 0 3 read-only 000 Receive FIFO/Buffer depth = 1 dataword. #000 001 Receive FIFO/Buffer depth = 4 datawords. #001 010 Receive FIFO/Buffer depth = 8 datawords. #010 011 Receive FIFO/Buffer depth = 16 datawords. #011 100 Receive FIFO/Buffer depth = 32 datawords. #100 101 Receive FIFO/Buffer depth = 64 datawords. #101 110 Receive FIFO/Buffer depth = 128 datawords. #110 111 Receive FIFO/Buffer depth = 256 datawords. #111 RXFE Receive FIFO Enable 3 1 read-write 0 Receive FIFO is not enabled. Buffer is depth 1. (Legacy support) #0 1 Receive FIFO is enabled. Buffer is depth indicted by RXFIFOSIZE. #1 TXFIFOSIZE Transmit FIFO. Buffer Depth 4 3 read-only 000 Transmit FIFO/Buffer depth = 1 dataword. #000 001 Transmit FIFO/Buffer depth = 4 datawords. #001 010 Transmit FIFO/Buffer depth = 8 datawords. #010 011 Transmit FIFO/Buffer depth = 16 datawords. #011 100 Transmit FIFO/Buffer depth = 32 datawords. #100 101 Transmit FIFO/Buffer depth = 64 datawords. #101 110 Transmit FIFO/Buffer depth = 128 datawords. #110 111 Transmit FIFO/Buffer depth = 256 datawords #111 TXFE Transmit FIFO Enable 7 1 read-write 0 Transmit FIFO is not enabled. Buffer is depth 1. (Legacy support). #0 1 Transmit FIFO is enabled. Buffer is depth indicated by TXFIFOSIZE. #1 RXUFE Receive FIFO Underflow Interrupt Enable 8 1 read-write 0 RXUF flag does not generate an interrupt to the host. #0 1 RXUF flag generates an interrupt to the host. #1 TXOFE Transmit FIFO Overflow Interrupt Enable 9 1 read-write 0 TXOF flag does not generate an interrupt to the host. #0 1 TXOF flag generates an interrupt to the host. #1 RXIDEN Receiver Idle Empty Enable 10 3 read-write 000 Disable RDRF assertion due to partially filled FIFO when receiver is idle. #000 001 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 1 character. #001 010 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 2 characters. #010 011 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 4 characters. #011 100 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 8 characters. #100 101 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 16 characters. #101 110 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 32 characters. #110 111 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 64 characters. #111 RXFLUSH Receive FIFO/Buffer Flush 14 1 write-only 0 No flush operation occurs. #0 1 All data in the receive FIFO/buffer is cleared out. #1 TXFLUSH Transmit FIFO/Buffer Flush 15 1 write-only 0 No flush operation occurs. #0 1 All data in the transmit FIFO/Buffer is cleared out. #1 RXUF Receiver Buffer Underflow Flag 16 1 read-write 0 No receive buffer underflow has occurred since the last time the flag was cleared. #0 1 At least one receive buffer underflow has occurred since the last time the flag was cleared. #1 TXOF Transmitter Buffer Overflow Flag 17 1 read-write 0 No transmit buffer overflow has occurred since the last time the flag was cleared. #0 1 At least one transmit buffer overflow has occurred since the last time the flag was cleared. #1 RXEMPT Receive Buffer/FIFO Empty 22 1 read-only 0 Receive buffer is not empty. #0 1 Receive buffer is empty. #1 TXEMPT Transmit Buffer/FIFO Empty 23 1 read-only 0 Transmit buffer is not empty. #0 1 Transmit buffer is empty. #1 WATER LPUART Watermark Register 0x2C 32 read-write 0 0xFFFFFFFF TXWATER Transmit Watermark 0 8 read-write TXCOUNT Transmit Counter 8 8 read-only RXWATER Receive Watermark 16 8 read-write RXCOUNT Receive Counter 24 8 read-only LPUART1 LPUART LPUART 0x4006B000 0 0x30 registers LPUART1 13 VERID Version ID Register 0 32 read-only 0x4010003 0xFFFFFFFF FEATURE Feature Identification Number 0 16 read-only 0x1 Standard feature set. #1 0x3 Standard feature set with MODEM/IrDA support. #11 MINOR Minor Version Number 16 8 read-only MAJOR Major Version Number 24 8 read-only PARAM Parameter Register 0x4 32 read-only 0x202 0xFFFFFFFF TXFIFO Transmit FIFO Size 0 8 read-only RXFIFO Receive FIFO Size 8 8 read-only GLOBAL LPUART Global Register 0x8 32 read-write 0 0xFFFFFFFF RST Software Reset 1 1 read-write 0 Module is not reset. #0 1 Module is reset. #1 PINCFG LPUART Pin Configuration Register 0xC 32 read-write 0 0xFFFFFFFF TRGSEL Trigger Select 0 2 read-write 00 Input trigger is disabled. #00 01 Input trigger is used instead of RXD pin input. #01 10 Input trigger is used instead of CTS_B pin input. #10 11 Input trigger is used to modulate the TXD pin output. #11 BAUD LPUART Baud Rate Register 0x10 32 read-write 0xF000004 0xFFFFFFFF SBR Baud Rate Modulo Divisor. 0 13 read-write SBNS Stop Bit Number Select 13 1 read-write 0 One stop bit. #0 1 Two stop bits. #1 RXEDGIE RX Input Active Edge Interrupt Enable 14 1 read-write 0 Hardware interrupts from LPUART_STAT[RXEDGIF] disabled (use polling). #0 1 Hardware interrupt requested when LPUART_STAT[RXEDGIF] flag is 1. #1 LBKDIE LIN Break Detect Interrupt Enable 15 1 read-write 0 Hardware interrupts from LPUART_STAT[LBKDIF] disabled (use polling). #0 1 Hardware interrupt requested when LPUART_STAT[LBKDIF] flag is 1. #1 RESYNCDIS Resynchronization Disable 16 1 read-write 0 Resynchronization during received data word is supported #0 1 Resynchronization during received data word is disabled #1 BOTHEDGE Both Edge Sampling 17 1 read-write 0 Receiver samples input data using the rising edge of the baud rate clock. #0 1 Receiver samples input data using the rising and falling edge of the baud rate clock. #1 MATCFG Match Configuration 18 2 read-write 00 Address Match Wakeup #00 01 Idle Match Wakeup #01 10 Match On and Match Off #10 RIDMAE Receiver Idle DMA Enable 20 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 RDMAE Receiver Full DMA Enable 21 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 TDMAE Transmitter DMA Enable 23 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 OSR Oversampling Ratio 24 5 read-write M10 10-bit Mode select 29 1 read-write 0 Receiver and transmitter use 7-bit to 9-bit data characters. #0 1 Receiver and transmitter use 10-bit data characters. #1 MAEN2 Match Address Mode Enable 2 30 1 read-write 0 Normal operation. #0 1 Enables automatic address matching or data matching mode for MATCH[MA2]. #1 MAEN1 Match Address Mode Enable 1 31 1 read-write 0 Normal operation. #0 1 Enables automatic address matching or data matching mode for MATCH[MA1]. #1 STAT LPUART Status Register 0x14 32 read-write 0xC00000 0xFFFFFFFF MA2F Match 2 Flag 14 1 read-write 0 Received data is not equal to MA2 #0 1 Received data is equal to MA2 #1 MA1F Match 1 Flag 15 1 read-write 0 Received data is not equal to MA1 #0 1 Received data is equal to MA1 #1 PF Parity Error Flag 16 1 read-write 0 No parity error. #0 1 Parity error. #1 FE Framing Error Flag 17 1 read-write 0 No framing error detected. This does not guarantee the framing is correct. #0 1 Framing error. #1 NF Noise Flag 18 1 read-write 0 No noise detected. #0 1 Noise detected in the received character in LPUART_DATA. #1 OR Receiver Overrun Flag 19 1 read-write 0 No overrun. #0 1 Receive overrun (new LPUART data lost). #1 IDLE Idle Line Flag 20 1 read-write 0 No idle line detected. #0 1 Idle line was detected. #1 RDRF Receive Data Register Full Flag 21 1 read-only 0 Receive data buffer empty. #0 1 Receive data buffer full. #1 TC Transmission Complete Flag 22 1 read-only 0 Transmitter active (sending data, a preamble, or a break). #0 1 Transmitter idle (transmission activity complete). #1 TDRE Transmit Data Register Empty Flag 23 1 read-only 0 Transmit data buffer full. #0 1 Transmit data buffer empty. #1 RAF Receiver Active Flag 24 1 read-only 0 LPUART receiver idle waiting for a start bit. #0 1 LPUART receiver active (RXD input not idle). #1 LBKDE LIN Break Detection Enable 25 1 read-write 0 LIN break detect is disabled, normal break character can be detected. #0 1 LIN break detect is enabled. LIN break character is detected at length of 11 bit times (if M = 0) or 12 (if M = 1) or 13 (M10 = 1). #1 BRK13 Break Character Generation Length 26 1 read-write 0 Break character is transmitted with length of 9 to 13 bit times. #0 1 Break character is transmitted with length of 12 to 15 bit times. #1 RWUID Receive Wake Up Idle Detect 27 1 read-write 0 During receive standby state (RWU = 1), the IDLE bit does not get set upon detection of an idle character. During address match wakeup, the IDLE bit does not get set when an address does not match. #0 1 During receive standby state (RWU = 1), the IDLE bit gets set upon detection of an idle character. During address match wakeup, the IDLE bit does get set when an address does not match. #1 RXINV Receive Data Inversion 28 1 read-write 0 Receive data not inverted. #0 1 Receive data inverted. #1 MSBF MSB First 29 1 read-write 0 LSB (bit0) is the first bit that is transmitted following the start bit. Further, the first bit received after the start bit is identified as bit0. #0 1 MSB (bit9, bit8, bit7 or bit6) is the first bit that is transmitted following the start bit depending on the setting of CTRL[M], CTRL[PE] and BAUD[M10]. Further, the first bit received after the start bit is identified as bit9, bit8, bit7 or bit6 depending on the setting of CTRL[M] and CTRL[PE]. #1 RXEDGIF RXD Pin Active Edge Interrupt Flag 30 1 read-write 0 No active edge on the receive pin has occurred. #0 1 An active edge on the receive pin has occurred. #1 LBKDIF LIN Break Detect Interrupt Flag 31 1 read-write 0 No LIN break character has been detected. #0 1 LIN break character has been detected. #1 CTRL LPUART Control Register 0x18 32 read-write 0 0xFFFFFFFF PT Parity Type 0 1 read-write 0 Even parity. #0 1 Odd parity. #1 PE Parity Enable 1 1 read-write 0 No hardware parity generation or checking. #0 1 Parity enabled. #1 ILT Idle Line Type Select 2 1 read-write 0 Idle character bit count starts after start bit. #0 1 Idle character bit count starts after stop bit. #1 WAKE Receiver Wakeup Method Select 3 1 read-write 0 Configures RWU for idle-line wakeup. #0 1 Configures RWU with address-mark wakeup. #1 M 9-Bit or 8-Bit Mode Select 4 1 read-write 0 Receiver and transmitter use 8-bit data characters. #0 1 Receiver and transmitter use 9-bit data characters. #1 RSRC Receiver Source Select 5 1 read-write 0 Provided LOOPS is set, RSRC is cleared, selects internal loop back mode and the LPUART does not use the RXD pin. #0 1 Single-wire LPUART mode where the TXD pin is connected to the transmitter output and receiver input. #1 DOZEEN Doze Enable 6 1 read-write 0 LPUART is enabled in Doze mode. #0 1 LPUART is disabled in Doze mode. #1 LOOPS Loop Mode Select 7 1 read-write 0 Normal operation - RXD and TXD use separate pins. #0 1 Loop mode or single-wire mode where transmitter outputs are internally connected to receiver input (see RSRC bit). #1 IDLECFG Idle Configuration 8 3 read-write 000 1 idle character #000 001 2 idle characters #001 010 4 idle characters #010 011 8 idle characters #011 100 16 idle characters #100 101 32 idle characters #101 110 64 idle characters #110 111 128 idle characters #111 M7 7-Bit Mode Select 11 1 read-write 0 Receiver and transmitter use 8-bit to 10-bit data characters. #0 1 Receiver and transmitter use 7-bit data characters. #1 MA2IE Match 2 Interrupt Enable 14 1 read-write 0 MA2F interrupt disabled #0 1 MA2F interrupt enabled #1 MA1IE Match 1 Interrupt Enable 15 1 read-write 0 MA1F interrupt disabled #0 1 MA1F interrupt enabled #1 SBK Send Break 16 1 read-write 0 Normal transmitter operation. #0 1 Queue break character(s) to be sent. #1 RWU Receiver Wakeup Control 17 1 read-write 0 Normal receiver operation. #0 1 LPUART receiver in standby waiting for wakeup condition. #1 RE Receiver Enable 18 1 read-write 0 Receiver disabled. #0 1 Receiver enabled. #1 TE Transmitter Enable 19 1 read-write 0 Transmitter disabled. #0 1 Transmitter enabled. #1 ILIE Idle Line Interrupt Enable 20 1 read-write 0 Hardware interrupts from IDLE disabled; use polling. #0 1 Hardware interrupt requested when IDLE flag is 1. #1 RIE Receiver Interrupt Enable 21 1 read-write 0 Hardware interrupts from RDRF disabled; use polling. #0 1 Hardware interrupt requested when RDRF flag is 1. #1 TCIE Transmission Complete Interrupt Enable for 22 1 read-write 0 Hardware interrupts from TC disabled; use polling. #0 1 Hardware interrupt requested when TC flag is 1. #1 TIE Transmit Interrupt Enable 23 1 read-write 0 Hardware interrupts from TDRE disabled; use polling. #0 1 Hardware interrupt requested when TDRE flag is 1. #1 PEIE Parity Error Interrupt Enable 24 1 read-write 0 PF interrupts disabled; use polling). #0 1 Hardware interrupt requested when PF is set. #1 FEIE Framing Error Interrupt Enable 25 1 read-write 0 FE interrupts disabled; use polling. #0 1 Hardware interrupt requested when FE is set. #1 NEIE Noise Error Interrupt Enable 26 1 read-write 0 NF interrupts disabled; use polling. #0 1 Hardware interrupt requested when NF is set. #1 ORIE Overrun Interrupt Enable 27 1 read-write 0 OR interrupts disabled; use polling. #0 1 Hardware interrupt requested when OR is set. #1 TXINV Transmit Data Inversion 28 1 read-write 0 Transmit data not inverted. #0 1 Transmit data inverted. #1 TXDIR TXD Pin Direction in Single-Wire Mode 29 1 read-write 0 TXD pin is an input in single-wire mode. #0 1 TXD pin is an output in single-wire mode. #1 R9T8 Receive Bit 9 / Transmit Bit 8 30 1 read-write R8T9 Receive Bit 8 / Transmit Bit 9 31 1 read-write DATA LPUART Data Register 0x1C 32 read-write 0x1000 0xFFFFFFFF R0T0 R0T0 0 1 read-write R1T1 R1T1 1 1 read-write R2T2 R2T2 2 1 read-write R3T3 R3T3 3 1 read-write R4T4 R4T4 4 1 read-write R5T5 R5T5 5 1 read-write R6T6 R6T6 6 1 read-write R7T7 R7T7 7 1 read-write R8T8 R8T8 8 1 read-write R9T9 R9T9 9 1 read-write IDLINE Idle Line 11 1 read-only 0 Receiver was not idle before receiving this character. #0 1 Receiver was idle before receiving this character. #1 RXEMPT Receive Buffer Empty 12 1 read-only 0 Receive buffer contains valid data. #0 1 Receive buffer is empty, data returned on read is not valid. #1 FRETSC Frame Error / Transmit Special Character 13 1 read-write 0 The dataword was received without a frame error on read, transmit a normal character on write. #0 1 The dataword was received with a frame error, transmit an idle or break character on transmit. #1 PARITYE PARITYE 14 1 read-only 0 The dataword was received without a parity error. #0 1 The dataword was received with a parity error. #1 NOISY NOISY 15 1 read-only 0 The dataword was received without noise. #0 1 The data was received with noise. #1 MATCH LPUART Match Address Register 0x20 32 read-write 0 0xFFFFFFFF MA1 Match Address 1 0 10 read-write MA2 Match Address 2 16 10 read-write MODIR LPUART Modem IrDA Register 0x24 32 read-write 0 0xFFFFFFFF TXCTSE Transmitter clear-to-send enable 0 1 read-write 0 CTS has no effect on the transmitter. #0 1 Enables clear-to-send operation. The transmitter checks the state of CTS each time it is ready to send a character. If CTS is asserted, the character is sent. If CTS is deasserted, the signal TXD remains in the mark state and transmission is delayed until CTS is asserted. Changes in CTS as a character is being sent do not affect its transmission. #1 TXRTSE Transmitter request-to-send enable 1 1 read-write 0 The transmitter has no effect on RTS. #0 1 When a character is placed into an empty transmitter data buffer , RTS asserts one bit time before the start bit is transmitted. RTS deasserts one bit time after all characters in the transmitter data buffer and shift register are completely sent, including the last stop bit. #1 TXRTSPOL Transmitter request-to-send polarity 2 1 read-write 0 Transmitter RTS is active low. #0 1 Transmitter RTS is active high. #1 RXRTSE Receiver request-to-send enable 3 1 read-write 0 The receiver has no effect on RTS. #0 TXCTSC Transmit CTS Configuration 4 1 read-write 0 CTS input is sampled at the start of each character. #0 1 CTS input is sampled when the transmitter is idle. #1 TXCTSSRC Transmit CTS Source 5 1 read-write 0 CTS input is the CTS_B pin. #0 1 CTS input is the inverted Receiver Match result. #1 RTSWATER Receive RTS Configuration 8 8 read-write TNP Transmitter narrow pulse 16 2 read-write 00 1/OSR. #00 01 2/OSR. #01 10 3/OSR. #10 11 4/OSR. #11 IREN Infrared enable 18 1 read-write 0 IR disabled. #0 1 IR enabled. #1 FIFO LPUART FIFO Register 0x28 32 read-write 0xC00011 0xFFFFFFFF RXFIFOSIZE Receive FIFO. Buffer Depth 0 3 read-only 000 Receive FIFO/Buffer depth = 1 dataword. #000 001 Receive FIFO/Buffer depth = 4 datawords. #001 010 Receive FIFO/Buffer depth = 8 datawords. #010 011 Receive FIFO/Buffer depth = 16 datawords. #011 100 Receive FIFO/Buffer depth = 32 datawords. #100 101 Receive FIFO/Buffer depth = 64 datawords. #101 110 Receive FIFO/Buffer depth = 128 datawords. #110 111 Receive FIFO/Buffer depth = 256 datawords. #111 RXFE Receive FIFO Enable 3 1 read-write 0 Receive FIFO is not enabled. Buffer is depth 1. (Legacy support) #0 1 Receive FIFO is enabled. Buffer is depth indicted by RXFIFOSIZE. #1 TXFIFOSIZE Transmit FIFO. Buffer Depth 4 3 read-only 000 Transmit FIFO/Buffer depth = 1 dataword. #000 001 Transmit FIFO/Buffer depth = 4 datawords. #001 010 Transmit FIFO/Buffer depth = 8 datawords. #010 011 Transmit FIFO/Buffer depth = 16 datawords. #011 100 Transmit FIFO/Buffer depth = 32 datawords. #100 101 Transmit FIFO/Buffer depth = 64 datawords. #101 110 Transmit FIFO/Buffer depth = 128 datawords. #110 111 Transmit FIFO/Buffer depth = 256 datawords #111 TXFE Transmit FIFO Enable 7 1 read-write 0 Transmit FIFO is not enabled. Buffer is depth 1. (Legacy support). #0 1 Transmit FIFO is enabled. Buffer is depth indicated by TXFIFOSIZE. #1 RXUFE Receive FIFO Underflow Interrupt Enable 8 1 read-write 0 RXUF flag does not generate an interrupt to the host. #0 1 RXUF flag generates an interrupt to the host. #1 TXOFE Transmit FIFO Overflow Interrupt Enable 9 1 read-write 0 TXOF flag does not generate an interrupt to the host. #0 1 TXOF flag generates an interrupt to the host. #1 RXIDEN Receiver Idle Empty Enable 10 3 read-write 000 Disable RDRF assertion due to partially filled FIFO when receiver is idle. #000 001 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 1 character. #001 010 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 2 characters. #010 011 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 4 characters. #011 100 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 8 characters. #100 101 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 16 characters. #101 110 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 32 characters. #110 111 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 64 characters. #111 RXFLUSH Receive FIFO/Buffer Flush 14 1 write-only 0 No flush operation occurs. #0 1 All data in the receive FIFO/buffer is cleared out. #1 TXFLUSH Transmit FIFO/Buffer Flush 15 1 write-only 0 No flush operation occurs. #0 1 All data in the transmit FIFO/Buffer is cleared out. #1 RXUF Receiver Buffer Underflow Flag 16 1 read-write 0 No receive buffer underflow has occurred since the last time the flag was cleared. #0 1 At least one receive buffer underflow has occurred since the last time the flag was cleared. #1 TXOF Transmitter Buffer Overflow Flag 17 1 read-write 0 No transmit buffer overflow has occurred since the last time the flag was cleared. #0 1 At least one transmit buffer overflow has occurred since the last time the flag was cleared. #1 RXEMPT Receive Buffer/FIFO Empty 22 1 read-only 0 Receive buffer is not empty. #0 1 Receive buffer is empty. #1 TXEMPT Transmit Buffer/FIFO Empty 23 1 read-only 0 Transmit buffer is not empty. #0 1 Transmit buffer is empty. #1 WATER LPUART Watermark Register 0x2C 32 read-write 0 0xFFFFFFFF TXWATER Transmit Watermark 0 8 read-write TXCOUNT Transmit Counter 8 8 read-only RXWATER Receive Watermark 16 8 read-write RXCOUNT Receive Counter 24 8 read-only LPUART2 LPUART LPUART 0x4006C000 0 0x30 registers LPUART2 14 VERID Version ID Register 0 32 read-only 0x4010003 0xFFFFFFFF FEATURE Feature Identification Number 0 16 read-only 0x1 Standard feature set. #1 0x3 Standard feature set with MODEM/IrDA support. #11 MINOR Minor Version Number 16 8 read-only MAJOR Major Version Number 24 8 read-only PARAM Parameter Register 0x4 32 read-only 0x202 0xFFFFFFFF TXFIFO Transmit FIFO Size 0 8 read-only RXFIFO Receive FIFO Size 8 8 read-only GLOBAL LPUART Global Register 0x8 32 read-write 0 0xFFFFFFFF RST Software Reset 1 1 read-write 0 Module is not reset. #0 1 Module is reset. #1 PINCFG LPUART Pin Configuration Register 0xC 32 read-write 0 0xFFFFFFFF TRGSEL Trigger Select 0 2 read-write 00 Input trigger is disabled. #00 01 Input trigger is used instead of RXD pin input. #01 10 Input trigger is used instead of CTS_B pin input. #10 11 Input trigger is used to modulate the TXD pin output. #11 BAUD LPUART Baud Rate Register 0x10 32 read-write 0xF000004 0xFFFFFFFF SBR Baud Rate Modulo Divisor. 0 13 read-write SBNS Stop Bit Number Select 13 1 read-write 0 One stop bit. #0 1 Two stop bits. #1 RXEDGIE RX Input Active Edge Interrupt Enable 14 1 read-write 0 Hardware interrupts from LPUART_STAT[RXEDGIF] disabled (use polling). #0 1 Hardware interrupt requested when LPUART_STAT[RXEDGIF] flag is 1. #1 LBKDIE LIN Break Detect Interrupt Enable 15 1 read-write 0 Hardware interrupts from LPUART_STAT[LBKDIF] disabled (use polling). #0 1 Hardware interrupt requested when LPUART_STAT[LBKDIF] flag is 1. #1 RESYNCDIS Resynchronization Disable 16 1 read-write 0 Resynchronization during received data word is supported #0 1 Resynchronization during received data word is disabled #1 BOTHEDGE Both Edge Sampling 17 1 read-write 0 Receiver samples input data using the rising edge of the baud rate clock. #0 1 Receiver samples input data using the rising and falling edge of the baud rate clock. #1 MATCFG Match Configuration 18 2 read-write 00 Address Match Wakeup #00 01 Idle Match Wakeup #01 10 Match On and Match Off #10 RIDMAE Receiver Idle DMA Enable 20 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 RDMAE Receiver Full DMA Enable 21 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 TDMAE Transmitter DMA Enable 23 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 OSR Oversampling Ratio 24 5 read-write M10 10-bit Mode select 29 1 read-write 0 Receiver and transmitter use 7-bit to 9-bit data characters. #0 1 Receiver and transmitter use 10-bit data characters. #1 MAEN2 Match Address Mode Enable 2 30 1 read-write 0 Normal operation. #0 1 Enables automatic address matching or data matching mode for MATCH[MA2]. #1 MAEN1 Match Address Mode Enable 1 31 1 read-write 0 Normal operation. #0 1 Enables automatic address matching or data matching mode for MATCH[MA1]. #1 STAT LPUART Status Register 0x14 32 read-write 0xC00000 0xFFFFFFFF MA2F Match 2 Flag 14 1 read-write 0 Received data is not equal to MA2 #0 1 Received data is equal to MA2 #1 MA1F Match 1 Flag 15 1 read-write 0 Received data is not equal to MA1 #0 1 Received data is equal to MA1 #1 PF Parity Error Flag 16 1 read-write 0 No parity error. #0 1 Parity error. #1 FE Framing Error Flag 17 1 read-write 0 No framing error detected. This does not guarantee the framing is correct. #0 1 Framing error. #1 NF Noise Flag 18 1 read-write 0 No noise detected. #0 1 Noise detected in the received character in LPUART_DATA. #1 OR Receiver Overrun Flag 19 1 read-write 0 No overrun. #0 1 Receive overrun (new LPUART data lost). #1 IDLE Idle Line Flag 20 1 read-write 0 No idle line detected. #0 1 Idle line was detected. #1 RDRF Receive Data Register Full Flag 21 1 read-only 0 Receive data buffer empty. #0 1 Receive data buffer full. #1 TC Transmission Complete Flag 22 1 read-only 0 Transmitter active (sending data, a preamble, or a break). #0 1 Transmitter idle (transmission activity complete). #1 TDRE Transmit Data Register Empty Flag 23 1 read-only 0 Transmit data buffer full. #0 1 Transmit data buffer empty. #1 RAF Receiver Active Flag 24 1 read-only 0 LPUART receiver idle waiting for a start bit. #0 1 LPUART receiver active (RXD input not idle). #1 LBKDE LIN Break Detection Enable 25 1 read-write 0 LIN break detect is disabled, normal break character can be detected. #0 1 LIN break detect is enabled. LIN break character is detected at length of 11 bit times (if M = 0) or 12 (if M = 1) or 13 (M10 = 1). #1 BRK13 Break Character Generation Length 26 1 read-write 0 Break character is transmitted with length of 9 to 13 bit times. #0 1 Break character is transmitted with length of 12 to 15 bit times. #1 RWUID Receive Wake Up Idle Detect 27 1 read-write 0 During receive standby state (RWU = 1), the IDLE bit does not get set upon detection of an idle character. During address match wakeup, the IDLE bit does not get set when an address does not match. #0 1 During receive standby state (RWU = 1), the IDLE bit gets set upon detection of an idle character. During address match wakeup, the IDLE bit does get set when an address does not match. #1 RXINV Receive Data Inversion 28 1 read-write 0 Receive data not inverted. #0 1 Receive data inverted. #1 MSBF MSB First 29 1 read-write 0 LSB (bit0) is the first bit that is transmitted following the start bit. Further, the first bit received after the start bit is identified as bit0. #0 1 MSB (bit9, bit8, bit7 or bit6) is the first bit that is transmitted following the start bit depending on the setting of CTRL[M], CTRL[PE] and BAUD[M10]. Further, the first bit received after the start bit is identified as bit9, bit8, bit7 or bit6 depending on the setting of CTRL[M] and CTRL[PE]. #1 RXEDGIF RXD Pin Active Edge Interrupt Flag 30 1 read-write 0 No active edge on the receive pin has occurred. #0 1 An active edge on the receive pin has occurred. #1 LBKDIF LIN Break Detect Interrupt Flag 31 1 read-write 0 No LIN break character has been detected. #0 1 LIN break character has been detected. #1 CTRL LPUART Control Register 0x18 32 read-write 0 0xFFFFFFFF PT Parity Type 0 1 read-write 0 Even parity. #0 1 Odd parity. #1 PE Parity Enable 1 1 read-write 0 No hardware parity generation or checking. #0 1 Parity enabled. #1 ILT Idle Line Type Select 2 1 read-write 0 Idle character bit count starts after start bit. #0 1 Idle character bit count starts after stop bit. #1 WAKE Receiver Wakeup Method Select 3 1 read-write 0 Configures RWU for idle-line wakeup. #0 1 Configures RWU with address-mark wakeup. #1 M 9-Bit or 8-Bit Mode Select 4 1 read-write 0 Receiver and transmitter use 8-bit data characters. #0 1 Receiver and transmitter use 9-bit data characters. #1 RSRC Receiver Source Select 5 1 read-write 0 Provided LOOPS is set, RSRC is cleared, selects internal loop back mode and the LPUART does not use the RXD pin. #0 1 Single-wire LPUART mode where the TXD pin is connected to the transmitter output and receiver input. #1 DOZEEN Doze Enable 6 1 read-write 0 LPUART is enabled in Doze mode. #0 1 LPUART is disabled in Doze mode. #1 LOOPS Loop Mode Select 7 1 read-write 0 Normal operation - RXD and TXD use separate pins. #0 1 Loop mode or single-wire mode where transmitter outputs are internally connected to receiver input (see RSRC bit). #1 IDLECFG Idle Configuration 8 3 read-write 000 1 idle character #000 001 2 idle characters #001 010 4 idle characters #010 011 8 idle characters #011 100 16 idle characters #100 101 32 idle characters #101 110 64 idle characters #110 111 128 idle characters #111 M7 7-Bit Mode Select 11 1 read-write 0 Receiver and transmitter use 8-bit to 10-bit data characters. #0 1 Receiver and transmitter use 7-bit data characters. #1 MA2IE Match 2 Interrupt Enable 14 1 read-write 0 MA2F interrupt disabled #0 1 MA2F interrupt enabled #1 MA1IE Match 1 Interrupt Enable 15 1 read-write 0 MA1F interrupt disabled #0 1 MA1F interrupt enabled #1 SBK Send Break 16 1 read-write 0 Normal transmitter operation. #0 1 Queue break character(s) to be sent. #1 RWU Receiver Wakeup Control 17 1 read-write 0 Normal receiver operation. #0 1 LPUART receiver in standby waiting for wakeup condition. #1 RE Receiver Enable 18 1 read-write 0 Receiver disabled. #0 1 Receiver enabled. #1 TE Transmitter Enable 19 1 read-write 0 Transmitter disabled. #0 1 Transmitter enabled. #1 ILIE Idle Line Interrupt Enable 20 1 read-write 0 Hardware interrupts from IDLE disabled; use polling. #0 1 Hardware interrupt requested when IDLE flag is 1. #1 RIE Receiver Interrupt Enable 21 1 read-write 0 Hardware interrupts from RDRF disabled; use polling. #0 1 Hardware interrupt requested when RDRF flag is 1. #1 TCIE Transmission Complete Interrupt Enable for 22 1 read-write 0 Hardware interrupts from TC disabled; use polling. #0 1 Hardware interrupt requested when TC flag is 1. #1 TIE Transmit Interrupt Enable 23 1 read-write 0 Hardware interrupts from TDRE disabled; use polling. #0 1 Hardware interrupt requested when TDRE flag is 1. #1 PEIE Parity Error Interrupt Enable 24 1 read-write 0 PF interrupts disabled; use polling). #0 1 Hardware interrupt requested when PF is set. #1 FEIE Framing Error Interrupt Enable 25 1 read-write 0 FE interrupts disabled; use polling. #0 1 Hardware interrupt requested when FE is set. #1 NEIE Noise Error Interrupt Enable 26 1 read-write 0 NF interrupts disabled; use polling. #0 1 Hardware interrupt requested when NF is set. #1 ORIE Overrun Interrupt Enable 27 1 read-write 0 OR interrupts disabled; use polling. #0 1 Hardware interrupt requested when OR is set. #1 TXINV Transmit Data Inversion 28 1 read-write 0 Transmit data not inverted. #0 1 Transmit data inverted. #1 TXDIR TXD Pin Direction in Single-Wire Mode 29 1 read-write 0 TXD pin is an input in single-wire mode. #0 1 TXD pin is an output in single-wire mode. #1 R9T8 Receive Bit 9 / Transmit Bit 8 30 1 read-write R8T9 Receive Bit 8 / Transmit Bit 9 31 1 read-write DATA LPUART Data Register 0x1C 32 read-write 0x1000 0xFFFFFFFF R0T0 R0T0 0 1 read-write R1T1 R1T1 1 1 read-write R2T2 R2T2 2 1 read-write R3T3 R3T3 3 1 read-write R4T4 R4T4 4 1 read-write R5T5 R5T5 5 1 read-write R6T6 R6T6 6 1 read-write R7T7 R7T7 7 1 read-write R8T8 R8T8 8 1 read-write R9T9 R9T9 9 1 read-write IDLINE Idle Line 11 1 read-only 0 Receiver was not idle before receiving this character. #0 1 Receiver was idle before receiving this character. #1 RXEMPT Receive Buffer Empty 12 1 read-only 0 Receive buffer contains valid data. #0 1 Receive buffer is empty, data returned on read is not valid. #1 FRETSC Frame Error / Transmit Special Character 13 1 read-write 0 The dataword was received without a frame error on read, transmit a normal character on write. #0 1 The dataword was received with a frame error, transmit an idle or break character on transmit. #1 PARITYE PARITYE 14 1 read-only 0 The dataword was received without a parity error. #0 1 The dataword was received with a parity error. #1 NOISY NOISY 15 1 read-only 0 The dataword was received without noise. #0 1 The data was received with noise. #1 MATCH LPUART Match Address Register 0x20 32 read-write 0 0xFFFFFFFF MA1 Match Address 1 0 10 read-write MA2 Match Address 2 16 10 read-write MODIR LPUART Modem IrDA Register 0x24 32 read-write 0 0xFFFFFFFF TXCTSE Transmitter clear-to-send enable 0 1 read-write 0 CTS has no effect on the transmitter. #0 1 Enables clear-to-send operation. The transmitter checks the state of CTS each time it is ready to send a character. If CTS is asserted, the character is sent. If CTS is deasserted, the signal TXD remains in the mark state and transmission is delayed until CTS is asserted. Changes in CTS as a character is being sent do not affect its transmission. #1 TXRTSE Transmitter request-to-send enable 1 1 read-write 0 The transmitter has no effect on RTS. #0 1 When a character is placed into an empty transmitter data buffer , RTS asserts one bit time before the start bit is transmitted. RTS deasserts one bit time after all characters in the transmitter data buffer and shift register are completely sent, including the last stop bit. #1 TXRTSPOL Transmitter request-to-send polarity 2 1 read-write 0 Transmitter RTS is active low. #0 1 Transmitter RTS is active high. #1 RXRTSE Receiver request-to-send enable 3 1 read-write 0 The receiver has no effect on RTS. #0 TXCTSC Transmit CTS Configuration 4 1 read-write 0 CTS input is sampled at the start of each character. #0 1 CTS input is sampled when the transmitter is idle. #1 TXCTSSRC Transmit CTS Source 5 1 read-write 0 CTS input is the CTS_B pin. #0 1 CTS input is the inverted Receiver Match result. #1 RTSWATER Receive RTS Configuration 8 8 read-write TNP Transmitter narrow pulse 16 2 read-write 00 1/OSR. #00 01 2/OSR. #01 10 3/OSR. #10 11 4/OSR. #11 IREN Infrared enable 18 1 read-write 0 IR disabled. #0 1 IR enabled. #1 FIFO LPUART FIFO Register 0x28 32 read-write 0xC00011 0xFFFFFFFF RXFIFOSIZE Receive FIFO. Buffer Depth 0 3 read-only 000 Receive FIFO/Buffer depth = 1 dataword. #000 001 Receive FIFO/Buffer depth = 4 datawords. #001 010 Receive FIFO/Buffer depth = 8 datawords. #010 011 Receive FIFO/Buffer depth = 16 datawords. #011 100 Receive FIFO/Buffer depth = 32 datawords. #100 101 Receive FIFO/Buffer depth = 64 datawords. #101 110 Receive FIFO/Buffer depth = 128 datawords. #110 111 Receive FIFO/Buffer depth = 256 datawords. #111 RXFE Receive FIFO Enable 3 1 read-write 0 Receive FIFO is not enabled. Buffer is depth 1. (Legacy support) #0 1 Receive FIFO is enabled. Buffer is depth indicted by RXFIFOSIZE. #1 TXFIFOSIZE Transmit FIFO. Buffer Depth 4 3 read-only 000 Transmit FIFO/Buffer depth = 1 dataword. #000 001 Transmit FIFO/Buffer depth = 4 datawords. #001 010 Transmit FIFO/Buffer depth = 8 datawords. #010 011 Transmit FIFO/Buffer depth = 16 datawords. #011 100 Transmit FIFO/Buffer depth = 32 datawords. #100 101 Transmit FIFO/Buffer depth = 64 datawords. #101 110 Transmit FIFO/Buffer depth = 128 datawords. #110 111 Transmit FIFO/Buffer depth = 256 datawords #111 TXFE Transmit FIFO Enable 7 1 read-write 0 Transmit FIFO is not enabled. Buffer is depth 1. (Legacy support). #0 1 Transmit FIFO is enabled. Buffer is depth indicated by TXFIFOSIZE. #1 RXUFE Receive FIFO Underflow Interrupt Enable 8 1 read-write 0 RXUF flag does not generate an interrupt to the host. #0 1 RXUF flag generates an interrupt to the host. #1 TXOFE Transmit FIFO Overflow Interrupt Enable 9 1 read-write 0 TXOF flag does not generate an interrupt to the host. #0 1 TXOF flag generates an interrupt to the host. #1 RXIDEN Receiver Idle Empty Enable 10 3 read-write 000 Disable RDRF assertion due to partially filled FIFO when receiver is idle. #000 001 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 1 character. #001 010 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 2 characters. #010 011 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 4 characters. #011 100 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 8 characters. #100 101 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 16 characters. #101 110 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 32 characters. #110 111 Enable RDRF assertion due to partially filled FIFO when receiver is idle for 64 characters. #111 RXFLUSH Receive FIFO/Buffer Flush 14 1 write-only 0 No flush operation occurs. #0 1 All data in the receive FIFO/buffer is cleared out. #1 TXFLUSH Transmit FIFO/Buffer Flush 15 1 write-only 0 No flush operation occurs. #0 1 All data in the transmit FIFO/Buffer is cleared out. #1 RXUF Receiver Buffer Underflow Flag 16 1 read-write 0 No receive buffer underflow has occurred since the last time the flag was cleared. #0 1 At least one receive buffer underflow has occurred since the last time the flag was cleared. #1 TXOF Transmitter Buffer Overflow Flag 17 1 read-write 0 No transmit buffer overflow has occurred since the last time the flag was cleared. #0 1 At least one transmit buffer overflow has occurred since the last time the flag was cleared. #1 RXEMPT Receive Buffer/FIFO Empty 22 1 read-only 0 Receive buffer is not empty. #0 1 Receive buffer is empty. #1 TXEMPT Transmit Buffer/FIFO Empty 23 1 read-only 0 Transmit buffer is not empty. #0 1 Transmit buffer is empty. #1 WATER LPUART Watermark Register 0x2C 32 read-write 0 0xFFFFFFFF TXWATER Transmit Watermark 0 8 read-write TXCOUNT Transmit Counter 8 8 read-only RXWATER Receive Watermark 16 8 read-write RXCOUNT Receive Counter 24 8 read-only CMP0 High-Speed Comparator (CMP), Voltage Reference (VREF) Digital-to-Analog Converter (DAC), and Analog Mux (ANMUX) CMP CMP0_ 0x40073000 0 0xC registers CMP0 16 C0 CMP Control Register 0 0 32 read-write 0 0xFFFFFFFF HYSTCTR Comparator hard block hysteresis control. See chip data sheet to get the actual hystersis value with each level 0 2 read-write 00 The hard block output has level 0 hysteresis internally. #00 01 The hard block output has level 1 hysteresis internally. #01 10 The hard block output has level 2 hysteresis internally. #10 11 The hard block output has level 3 hysteresis internally. #11 OFFSET Comparator hard block offset control. See chip data sheet to get the actual offset value with each level 2 1 read-write 0 The comparator hard block output has level 0 offset internally. #0 1 The comparator hard block output has level 1 offset internally. #1 FILTER_CNT Filter Sample Count 4 3 read-write 000 Filter is disabled. If SE = 1, then COUT is a logic zero (this is not a legal state, and is not recommended). If SE = 0, COUT = COUTA. #000 001 1 consecutive sample must agree (comparator output is simply sampled). #001 010 2 consecutive samples must agree. #010 011 3 consecutive samples must agree. #011 100 4 consecutive samples must agree. #100 101 5 consecutive samples must agree. #101 110 6 consecutive samples must agree. #110 111 7 consecutive samples must agree. #111 EN Comparator Module Enable 8 1 read-write 0 Analog Comparator is disabled. #0 1 Analog Comparator is enabled. #1 OPE Comparator Output Pin Enable 9 1 read-write 0 When OPE is 0, the comparator output (after window/filter settings dependent on software configuration) is not available to a packaged pin. #0 1 When OPE is 1, and if the software has configured the comparator to own a packaged pin, the comparator is available in a packaged pin. #1 COS Comparator Output Select 10 1 read-write 0 Set CMPO to equal COUT (filtered comparator output). #0 1 Set CMPO to equal COUTA (unfiltered comparator output). #1 INVT Comparator invert 11 1 read-write 0 Does not invert the comparator output. #0 1 Inverts the comparator output. #1 PMODE Power Mode Select 12 1 read-write 0 Low Speed (LS) comparison mode is selected. #0 1 High Speed (HS) comparison mode is selected, in VLPx mode, or Stop mode switched to Low Speed (LS) mode. #1 WE Windowing Enable 14 1 read-write 0 Windowing mode is not selected. #0 1 Windowing mode is selected. #1 SE Sample Enable 15 1 read-write 0 Sampling mode is not selected. #0 1 Sampling mode is selected. #1 FPR Filter Sample Period 16 8 read-write COUT Analog Comparator Output 24 1 read-only CFF Analog Comparator Flag Falling 25 1 read-write 0 A falling edge has not been detected on COUT. #0 1 A falling edge on COUT has occurred. #1 CFR Analog Comparator Flag Rising 26 1 read-write 0 A rising edge has not been detected on COUT. #0 1 A rising edge on COUT has occurred. #1 IEF Comparator Interrupt Enable Falling 27 1 read-write 0 Interrupt is disabled. #0 1 Interrupt is enabled. #1 IER Comparator Interrupt Enable Rising 28 1 read-write 0 Interrupt is disabled. #0 1 Interrupt is enabled. #1 DMAEN DMA Enable 30 1 read-write 0 DMA is disabled. #0 1 DMA is enabled. #1 C1 CMP Control Register 1 0x4 32 read-write 0 0xFFFFFFFF VOSEL DAC Output Voltage Select 0 8 read-write MSEL Minus Input MUX Control 8 3 read-write 000 IN0 #000 001 IN1 #001 010 IN2 #010 011 IN3 #011 100 IN4 #100 101 IN5 #101 110 IN6 #110 111 IN7 #111 PSEL Plus Input MUX Control 11 3 read-write 000 IN0 #000 001 IN1 #001 010 IN2 #010 011 IN3 #011 100 IN4 #100 101 IN5 #101 110 IN6 #110 111 IN7 #111 VRSEL Supply Voltage Reference Source Select 14 1 read-write 0 Vin1 is selected as resistor ladder network supply reference Vin. #0 1 Vin2 is selected as resistor ladder network supply reference Vin. #1 DACEN DAC Enable 15 1 read-write 0 DAC is disabled. #0 1 DAC is enabled. #1 CHN0 Channel 0 input enable 16 1 read-write CHN1 Channel 1 input enable 17 1 read-write CHN2 Channel 2 input enable 18 1 read-write CHN3 Channel 3 input enable 19 1 read-write CHN4 Channel 4 input enable 20 1 read-write CHN5 Channel 5 input enable 21 1 read-write CHN6 Channel 6 input enable 22 1 read-write CHN7 Channel 7 input enable 23 1 read-write INNSEL Selection of the input to the negative port of the comparator 24 2 read-write 00 IN0, from the 8-bit DAC output #00 01 IN1, from the analog 8-1 mux #01 INPSEL Selection of the input to the positive port of the comparator 27 2 read-write 00 IN0, from the 8-bit DAC output #00 01 IN1, from the analog 8-1 mux #01 DACOE DAC output Enable 29 1 read-write 0 DAC output is disabled to go outside. #0 1 DAC output is enabled to go outside. #1 C2 CMP Control Register 2 0x8 32 read-write 0 0xFFFFFFFF ACOn The result of the input comparison for channel n 0 8 read-write INITMOD Comparator and DAC initialization delay modulus. 8 6 read-write 000000 The modulus is set to 64(same with 111111). #0 NSAM Number of sample clocks 14 2 read-write 00 The comparison result is sampled as soon as the active channel is scanned in one round-robin clock. #00 01 The sampling takes place 1 round-robin clock cycle after the next cycle of the round-robin clock. #01 10 The sampling takes place 2 round-robin clock cycles after the next cycle of the round-robin clock. #10 11 The sampling takes place 3 round-robin clock cycles after the next cycle of the round-robin clock. #11 CH0F Channel 0 input changed flag 16 1 read-write CH1F Channel 1 input changed flag 17 1 read-write CH2F Channel 2 input changed flag 18 1 read-write CH3F Channel 3 input changed flag 19 1 read-write CH4F Channel 4 input changed flag 20 1 read-write CH5F Channel 5 input changed flag 21 1 read-write CH6F Channel 6 input changed flag 22 1 read-write CH7F Channel 7 input changed flag 23 1 read-write FXMXCH Fixed channel selection 25 3 read-write 000 Channel 0 is selected as the fixed reference input for the fixed mux port. #000 001 Channel 1 is selected as the fixed reference input for the fixed mux port. #001 010 Channel 2 is selected as the fixed reference input for the fixed mux port. #010 011 Channel 3 is selected as the fixed reference input for the fixed mux port. #011 100 Channel 4 is selected as the fixed reference input for the fixed mux port. #100 101 Channel 5 is selected as the fixed reference input for the fixed mux port. #101 110 Channel 6 is selected as the fixed reference input for the fixed mux port. #110 111 Channel 7 is selected as the fixed reference input for the fixed mux port. #111 FXMP Fixed MUX Port 29 1 read-write 0 The Plus port is fixed. Only the inputs to the Minus port are swept in each round. #0 1 The Minus port is fixed. Only the inputs to the Plus port are swept in each round. #1 RRIE Round-Robin interrupt enable 30 1 read-write 0 The round-robin interrupt is disabled. #0 1 The round-robin interrupt is enabled when a comparison result changes from the last sample. #1 RRE Round-Robin Enable 31 1 read-write 0 Round-robin operation is disabled. #0 1 Round-robin operation is enabled. #1 CMP1 High-Speed Comparator (CMP), Voltage Reference (VREF) Digital-to-Analog Converter (DAC), and Analog Mux (ANMUX) CMP CMP1_ 0x40074000 0 0xC registers CMP1 21 C0 CMP Control Register 0 0 32 read-write 0 0xFFFFFFFF HYSTCTR Comparator hard block hysteresis control. See chip data sheet to get the actual hystersis value with each level 0 2 read-write 00 The hard block output has level 0 hysteresis internally. #00 01 The hard block output has level 1 hysteresis internally. #01 10 The hard block output has level 2 hysteresis internally. #10 11 The hard block output has level 3 hysteresis internally. #11 OFFSET Comparator hard block offset control. See chip data sheet to get the actual offset value with each level 2 1 read-write 0 The comparator hard block output has level 0 offset internally. #0 1 The comparator hard block output has level 1 offset internally. #1 FILTER_CNT Filter Sample Count 4 3 read-write 000 Filter is disabled. If SE = 1, then COUT is a logic zero (this is not a legal state, and is not recommended). If SE = 0, COUT = COUTA. #000 001 1 consecutive sample must agree (comparator output is simply sampled). #001 010 2 consecutive samples must agree. #010 011 3 consecutive samples must agree. #011 100 4 consecutive samples must agree. #100 101 5 consecutive samples must agree. #101 110 6 consecutive samples must agree. #110 111 7 consecutive samples must agree. #111 EN Comparator Module Enable 8 1 read-write 0 Analog Comparator is disabled. #0 1 Analog Comparator is enabled. #1 OPE Comparator Output Pin Enable 9 1 read-write 0 When OPE is 0, the comparator output (after window/filter settings dependent on software configuration) is not available to a packaged pin. #0 1 When OPE is 1, and if the software has configured the comparator to own a packaged pin, the comparator is available in a packaged pin. #1 COS Comparator Output Select 10 1 read-write 0 Set CMPO to equal COUT (filtered comparator output). #0 1 Set CMPO to equal COUTA (unfiltered comparator output). #1 INVT Comparator invert 11 1 read-write 0 Does not invert the comparator output. #0 1 Inverts the comparator output. #1 PMODE Power Mode Select 12 1 read-write 0 Low Speed (LS) comparison mode is selected. #0 1 High Speed (HS) comparison mode is selected, in VLPx mode, or Stop mode switched to Low Speed (LS) mode. #1 WE Windowing Enable 14 1 read-write 0 Windowing mode is not selected. #0 1 Windowing mode is selected. #1 SE Sample Enable 15 1 read-write 0 Sampling mode is not selected. #0 1 Sampling mode is selected. #1 FPR Filter Sample Period 16 8 read-write COUT Analog Comparator Output 24 1 read-only CFF Analog Comparator Flag Falling 25 1 read-write 0 A falling edge has not been detected on COUT. #0 1 A falling edge on COUT has occurred. #1 CFR Analog Comparator Flag Rising 26 1 read-write 0 A rising edge has not been detected on COUT. #0 1 A rising edge on COUT has occurred. #1 IEF Comparator Interrupt Enable Falling 27 1 read-write 0 Interrupt is disabled. #0 1 Interrupt is enabled. #1 IER Comparator Interrupt Enable Rising 28 1 read-write 0 Interrupt is disabled. #0 1 Interrupt is enabled. #1 DMAEN DMA Enable 30 1 read-write 0 DMA is disabled. #0 1 DMA is enabled. #1 C1 CMP Control Register 1 0x4 32 read-write 0 0xFFFFFFFF VOSEL DAC Output Voltage Select 0 8 read-write MSEL Minus Input MUX Control 8 3 read-write 000 IN0 #000 001 IN1 #001 010 IN2 #010 011 IN3 #011 100 IN4 #100 101 IN5 #101 110 IN6 #110 111 IN7 #111 PSEL Plus Input MUX Control 11 3 read-write 000 IN0 #000 001 IN1 #001 010 IN2 #010 011 IN3 #011 100 IN4 #100 101 IN5 #101 110 IN6 #110 111 IN7 #111 VRSEL Supply Voltage Reference Source Select 14 1 read-write 0 Vin1 is selected as resistor ladder network supply reference Vin. #0 1 Vin2 is selected as resistor ladder network supply reference Vin. #1 DACEN DAC Enable 15 1 read-write 0 DAC is disabled. #0 1 DAC is enabled. #1 CHN0 Channel 0 input enable 16 1 read-write CHN1 Channel 1 input enable 17 1 read-write CHN2 Channel 2 input enable 18 1 read-write CHN3 Channel 3 input enable 19 1 read-write CHN4 Channel 4 input enable 20 1 read-write CHN5 Channel 5 input enable 21 1 read-write CHN6 Channel 6 input enable 22 1 read-write CHN7 Channel 7 input enable 23 1 read-write INNSEL Selection of the input to the negative port of the comparator 24 2 read-write 00 IN0, from the 8-bit DAC output #00 01 IN1, from the analog 8-1 mux #01 INPSEL Selection of the input to the positive port of the comparator 27 2 read-write 00 IN0, from the 8-bit DAC output #00 01 IN1, from the analog 8-1 mux #01 DACOE DAC output Enable 29 1 read-write 0 DAC output is disabled to go outside. #0 1 DAC output is enabled to go outside. #1 C2 CMP Control Register 2 0x8 32 read-write 0 0xFFFFFFFF ACOn The result of the input comparison for channel n 0 8 read-write INITMOD Comparator and DAC initialization delay modulus. 8 6 read-write 000000 The modulus is set to 64(same with 111111). #0 NSAM Number of sample clocks 14 2 read-write 00 The comparison result is sampled as soon as the active channel is scanned in one round-robin clock. #00 01 The sampling takes place 1 round-robin clock cycle after the next cycle of the round-robin clock. #01 10 The sampling takes place 2 round-robin clock cycles after the next cycle of the round-robin clock. #10 11 The sampling takes place 3 round-robin clock cycles after the next cycle of the round-robin clock. #11 CH0F Channel 0 input changed flag 16 1 read-write CH1F Channel 1 input changed flag 17 1 read-write CH2F Channel 2 input changed flag 18 1 read-write CH3F Channel 3 input changed flag 19 1 read-write CH4F Channel 4 input changed flag 20 1 read-write CH5F Channel 5 input changed flag 21 1 read-write CH6F Channel 6 input changed flag 22 1 read-write CH7F Channel 7 input changed flag 23 1 read-write FXMXCH Fixed channel selection 25 3 read-write 000 Channel 0 is selected as the fixed reference input for the fixed mux port. #000 001 Channel 1 is selected as the fixed reference input for the fixed mux port. #001 010 Channel 2 is selected as the fixed reference input for the fixed mux port. #010 011 Channel 3 is selected as the fixed reference input for the fixed mux port. #011 100 Channel 4 is selected as the fixed reference input for the fixed mux port. #100 101 Channel 5 is selected as the fixed reference input for the fixed mux port. #101 110 Channel 6 is selected as the fixed reference input for the fixed mux port. #110 111 Channel 7 is selected as the fixed reference input for the fixed mux port. #111 FXMP Fixed MUX Port 29 1 read-write 0 The Plus port is fixed. Only the inputs to the Minus port are swept in each round. #0 1 The Minus port is fixed. Only the inputs to the Plus port are swept in each round. #1 RRIE Round-Robin interrupt enable 30 1 read-write 0 The round-robin interrupt is disabled. #0 1 The round-robin interrupt is enabled when a comparison result changes from the last sample. #1 RRE Round-Robin Enable 31 1 read-write 0 Round-robin operation is disabled. #0 1 Round-robin operation is enabled. #1 PMC PMC PMC_ 0x4007D000 0 0x5 registers LVD_LVW 6 LVDSC1 Low Voltage Detect Status and Control 1 Register 0 8 read-write 0 0xFF LVDRE Low Voltage Detect Reset Enable 4 1 read-write 0 No system resets on low voltage detect events. #0 1 If the supply voltage falls below VLVD, a system reset will be generated. #1 LVDIE Low Voltage Detect Interrupt Enable 5 1 read-write 0 Hardware interrupt disabled (use polling) #0 1 Request a hardware interrupt when LVDF = 1 #1 LVDACK Low Voltage Detect Acknowledge 6 1 write-only LVDF Low Voltage Detect Flag 7 1 read-only 0 Low-voltage event not detected #0 1 Low-voltage event detected #1 LVDSC2 Low Voltage Detect Status and Control 2 Register 0x1 8 read-write 0 0xFF LVWIE Low-Voltage Warning Interrupt Enable 5 1 read-write 0 Hardware interrupt disabled (use polling) #0 1 Request a hardware interrupt when LVWF=1 #1 LVWACK Low-Voltage Warning Acknowledge 6 1 write-only LVWF Low-Voltage Warning Flag 7 1 read-only 0 Low-voltage warning event not detected #0 1 Low-voltage warning event detected #1 REGSC Regulator Status and Control Register 0x2 8 read-write 0x4 0xFF BIASEN Bias Enable Bit 0 1 read-write 0 Biasing disabled, core logic can run in full performance #0 1 Biasing enabled, core logic is slower and there are restrictions in allowed system clock speed (see device level specification for details) #1 REGFPM Regulator in Full Performance Mode Status Bit 2 1 read-only 0 Regulator is in low power mode or transition to/from #0 1 Regulator is in full performance mode #1 LPOSTAT LPO Status Bit 6 1 read-only 0 Low power oscillator in low phase #0 1 Low power oscillator in high phase #1 LPODIS LPO Disable Bit 7 1 read-write 0 Low power oscillator enabled #0 1 Low power oscillator disabled #1 LPOTRIM Low Power Oscillator Trim Register 0x4 8 read-write 0 0xFF LPOTRIM LPO trimming bits 0 5 read-write SMC System Mode Controller SMC_ 0x4007E000 0 0x18 registers VERID SMC Version ID Register 0 32 read-only 0x1000000 0xFFFFFFFF FEATURE Feature Specification Number 0 16 read-only 0 Standard features implemented #0 MINOR Minor Version Number 16 8 read-only MAJOR Major Version Number 24 8 read-only PARAM SMC Parameter Register 0x4 32 read-only 0 0xFFFFFFFF EHSRUN HSRUN feature exists 0 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 ELLS LLS feature exists 3 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 ELLS2 LLS2 feature exists 5 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 EVLLS0 VLLS0 feature exists 6 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 PMPROT Power Mode Protection register 0x8 32 read-write 0 0xFFFFFFFF AVLP Allow Very-Low-Power Modes 5 1 read-write 0 VLPR, VLPW, and VLPS are not allowed. #0 1 VLPR, VLPW, and VLPS are allowed. #1 PMCTRL Power Mode Control register 0xC 32 read-write 0 0xFFFFFFFF STOPM Stop Mode Control 0 3 read-write 000 Normal Stop (STOP) #000 010 Very-Low-Power Stop (VLPS) #010 110 Reseved #110 STOPA Stop Aborted 3 1 read-only 0 The previous stop mode entry was successful. #0 1 The previous stop mode entry was aborted. #1 RUNM Run Mode Control 5 2 read-write 00 Normal Run mode (RUN) #00 10 Very-Low-Power Run mode (VLPR) #10 STOPCTRL Stop Control Register 0x10 32 read-write 0x3 0xFFFFFFFF PSTOPO Partial Stop Option 6 2 read-write 00 STOP - Normal Stop mode #00 01 PSTOP1 - Partial Stop with both system and bus clocks disabled #01 10 PSTOP2 - Partial Stop with system clock disabled and bus clock enabled #10 PMSTAT Power Mode Status register 0x14 32 read-only 0x1 0xFFFFFFFF PMSTAT Power Mode Status 0 8 read-only RCM Reset Control Module RCM_ 0x4007F000 0 0x20 registers RCM 31 VERID Version ID Register 0 32 read-only 0x3000003 0xFFFFFFFF FEATURE Feature Specification Number 0 16 read-only 11 Standard feature set. #11 MINOR Minor Version Number 16 8 read-only MAJOR Major Version Number 24 8 read-only PARAM Parameter Register 0x4 32 read-only 0x2EEE 0xFFFFFFFF EWAKEUP Existence of SRS[WAKEUP] status indication feature 0 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 ELVD Existence of SRS[LVD] status indication feature 1 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 ELOC Existence of SRS[LOC] status indication feature 2 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 ELOL Existence of SRS[LOL] status indication feature 3 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 EWDOG Existence of SRS[WDOG] status indication feature 5 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 EPIN Existence of SRS[PIN] status indication feature 6 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 EPOR Existence of SRS[POR] status indication feature 7 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 EJTAG Existence of SRS[JTAG] status indication feature 8 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 ELOCKUP Existence of SRS[LOCKUP] status indication feature 9 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 ESW Existence of SRS[SW] status indication feature 10 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 EMDM_AP Existence of SRS[MDM_AP] status indication feature 11 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 ESACKERR Existence of SRS[SACKERR] status indication feature 13 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 ETAMPER Existence of SRS[TAMPER] status indication feature 15 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 ECORE1 Existence of SRS[CORE1] status indication feature 16 1 read-only 0 The feature is not available. #0 1 The feature is available. #1 SRS System Reset Status Register 0x8 32 read-only 0x82 0xFFFFFFFF LVD Low-Voltage Detect Reset or High-Voltage Detect Reset 1 1 read-only 0 Reset not caused by LVD trip, HVD trip or POR #0 1 Reset caused by LVD trip, HVD trip or POR #1 LOC Loss-of-Clock Reset 2 1 read-only 0 Reset not caused by a loss of external clock. #0 1 Reset caused by a loss of external clock. #1 LOL Loss-of-Lock Reset 3 1 read-only 0 Reset not caused by a loss of lock in the PLL #0 1 Reset caused by a loss of lock in the PLL #1 WDOG Watchdog 5 1 read-only 0 Reset not caused by watchdog timeout #0 1 Reset caused by watchdog timeout #1 PIN External Reset Pin 6 1 read-only 0 Reset not caused by external reset pin #0 1 Reset caused by external reset pin #1 POR Power-On Reset 7 1 read-only 0 Reset not caused by POR #0 1 Reset caused by POR #1 LOCKUP Core Lockup 9 1 read-only 0 Reset not caused by core LOCKUP event #0 1 Reset caused by core LOCKUP event #1 SW Software 10 1 read-only 0 Reset not caused by software setting of SYSRESETREQ bit #0 1 Reset caused by software setting of SYSRESETREQ bit #1 MDM_AP MDM-AP System Reset Request 11 1 read-only 0 Reset was not caused by host debugger system setting of the System Reset Request bit #0 1 Reset was caused by host debugger system setting of the System Reset Request bit #1 SACKERR Stop Acknowledge Error 13 1 read-only 0 Reset not caused by peripheral failure to acknowledge attempt to enter stop mode #0 1 Reset caused by peripheral failure to acknowledge attempt to enter stop mode #1 RPC Reset Pin Control register 0xC 32 read-write 0 0xFFFFFFFF RSTFLTSRW Reset Pin Filter Select in Run and Wait Modes 0 2 read-write 00 All filtering disabled #00 01 Bus clock filter enabled for normal operation #01 10 LPO clock filter enabled for normal operation #10 RSTFLTSS Reset Pin Filter Select in Stop Mode 2 1 read-write 0 All filtering disabled #0 1 LPO clock filter enabled #1 RSTFLTSEL Reset Pin Filter Bus Clock Select 8 5 read-write MR Mode Register 0x10 32 read-write 0 0xFFFFFFFF BOOTROM Boot ROM Configuration 1 2 read-write 00 Boot from Flash #00 01 Boot from ROM due to BOOTCFG0 pin assertion / Reserved if no Boot pin #01 10 Boot form ROM due to FOPT[7] configuration #10 11 Boot from ROM due to both BOOTCFG0 pin assertion and FOPT[7] configuration #11 FM Force Mode Register 0x14 32 read-write 0 0xFFFFFFFF FORCEROM Force ROM Boot 1 2 read-write 00 No effect #00 01 Force boot from ROM with RCM_MR[1] set. #01 10 Force boot from ROM with RCM_MR[2] set. #10 11 Force boot from ROM with RCM_MR[2:1] set. #11 SSRS Sticky System Reset Status Register 0x18 32 read-write 0x82 0xFFFFFFFF SLVD Sticky Low-Voltage Detect Reset 1 1 read-write 0 Reset not caused by LVD trip or POR #0 1 Reset caused by LVD trip or POR #1 SLOC Sticky Loss-of-Clock Reset 2 1 read-write 0 Reset not caused by a loss of external clock. #0 1 Reset caused by a loss of external clock. #1 SLOL Sticky Loss-of-Lock Reset 3 1 read-write 0 Reset not caused by a loss of lock in the PLL #0 1 Reset caused by a loss of lock in the PLL #1 SWDOG Sticky Watchdog 5 1 read-write 0 Reset not caused by watchdog timeout #0 1 Reset caused by watchdog timeout #1 SPIN Sticky External Reset Pin 6 1 read-write 0 Reset not caused by external reset pin #0 1 Reset caused by external reset pin #1 SPOR Sticky Power-On Reset 7 1 read-write 0 Reset not caused by POR #0 1 Reset caused by POR #1 SLOCKUP Sticky Core Lockup 9 1 read-write 0 Reset not caused by core LOCKUP event #0 1 Reset caused by core LOCKUP event #1 SSW Sticky Software 10 1 read-write 0 Reset not caused by software setting of SYSRESETREQ bit #0 1 Reset caused by software setting of SYSRESETREQ bit #1 SMDM_AP Sticky MDM-AP System Reset Request 11 1 read-only 0 Reset was not caused by host debugger system setting of the System Reset Request bit #0 1 Reset was caused by host debugger system setting of the System Reset Request bit #1 SSACKERR Sticky Stop Acknowledge Error 13 1 read-write 0 Reset not caused by peripheral failure to acknowledge attempt to enter stop mode #0 1 Reset caused by peripheral failure to acknowledge attempt to enter stop mode #1 SRIE System Reset Interrupt Enable Register 0x1C 32 read-write 0 0xFFFFFFFF DELAY Reset Delay Time 0 2 read-write 00 10 LPO cycles #00 01 34 LPO cycles #01 10 130 LPO cycles #10 11 514 LPO cycles #11 LOC Loss-of-Clock Interrupt 2 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 LOL Loss-of-Lock Interrupt 3 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 WDOG Watchdog Interrupt 5 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 PIN External Reset Pin Interrupt 6 1 read-write 0 Reset not caused by external reset pin #0 1 Reset caused by external reset pin #1 GIE Global Interrupt Enable 7 1 read-write 0 All interrupt sources disabled. #0 1 All interrupt sources enabled. #1 LOCKUP Core Lockup Interrupt 9 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 SW Software Interrupt 10 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 MDM_AP MDM-AP System Reset Request 11 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 SACKERR Stop Acknowledge Error Interrupt 13 1 read-write 0 Interrupt disabled. #0 1 Interrupt enabled. #1 GPIOA General Purpose Input/Output GPIO GPIOA_ 0x400FF000 0 0x18 registers PORTAE 7 PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 GPIOB General Purpose Input/Output GPIO GPIOB_ 0x400FF040 0 0x18 registers PORTBCD 26 PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 GPIOC General Purpose Input/Output GPIO GPIOC_ 0x400FF080 0 0x18 registers PORTBCD 26 PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 GPIOD General Purpose Input/Output GPIO GPIOD_ 0x400FF0C0 0 0x18 registers PORTBCD 26 PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 GPIOE General Purpose Input/Output GPIO GPIOE_ 0x400FF100 0 0x18 registers PORTAE 7 PDOR Port Data Output Register 0 32 read-write 0 0xFFFFFFFF PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only 0 0xFFFFFFFF PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PCOR Port Clear Output Register 0x8 32 write-only 0 0xFFFFFFFF PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTOR Port Toggle Output Register 0xC 32 write-only 0 0xFFFFFFFF PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PDIR Port Data Input Register 0x10 32 read-only 0 0xFFFFFFFF PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDDR Port Data Direction Register 0x14 32 read-write 0 0xFFFFFFFF PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 MTB Micro Trace Buffer MTB_ 0xF0000000 0 0x1000 registers POSITION MTB Position Register 0 32 read-write 0 0x3 WRAP WRAP 2 1 read-write POINTER Trace Packet Address Pointer[28:0] 3 29 read-write MASTER MTB Master Register 0x4 32 read-write 0x80 0xFFFFFFE0 MASK Mask 0 5 read-write TSTARTEN Trace Start Input Enable 5 1 read-write TSTOPEN Trace Stop Input Enable 6 1 read-write SFRWPRIV Special Function Register Write Privilege 7 1 read-write RAMPRIV RAM Privilege 8 1 read-write HALTREQ Halt Request 9 1 read-write EN Main Trace Enable 31 1 read-write FLOW MTB Flow Register 0x8 32 read-write 0 0x4 AUTOSTOP AUTOSTOP 0 1 read-write AUTOHALT AUTOHALT 1 1 read-write WATERMARK WATERMARK[28:0] 3 29 read-write BASE MTB Base Register 0xC 32 read-only 0 0 BASEADDR BASEADDR 0 32 read-only MODECTRL Integration Mode Control Register 0xF00 32 read-only 0 0xFFFFFFFF MODECTRL MODECTRL 0 32 read-only TAGSET Claim TAG Set Register 0xFA0 32 read-only 0 0xFFFFFFFF TAGSET TAGSET 0 32 read-only TAGCLEAR Claim TAG Clear Register 0xFA4 32 read-only 0 0xFFFFFFFF TAGCLEAR TAGCLEAR 0 32 read-only LOCKACCESS Lock Access Register 0xFB0 32 read-only 0 0xFFFFFFFF LOCKACCESS Hardwired to 0x0000_0000 0 32 read-only LOCKSTAT Lock Status Register 0xFB4 32 read-only 0 0xFFFFFFFF LOCKSTAT LOCKSTAT 0 32 read-only AUTHSTAT Authentication Status Register 0xFB8 32 read-only 0 0xFFFFFFFF BIT0 Connected to DBGEN. 0 1 read-only BIT2 BIT2 2 1 read-only DEVICEARCH Device Architecture Register 0xFBC 32 read-only 0x47700A31 0xFFFFFFFF DEVICEARCH DEVICEARCH 0 32 read-only DEVICECFG Device Configuration Register 0xFC8 32 read-only 0 0xFFFFFFFF DEVICECFG DEVICECFG 0 32 read-only DEVICETYPID Device Type Identifier Register 0xFCC 32 read-only 0x31 0xFFFFFFFF DEVICETYPID DEVICETYPID 0 32 read-only 8 0x4 4,5,6,7,0,1,2,3 PERIPHID%s Peripheral ID Register 0xFD0 32 read-only 0 0 PERIPHID PERIPHID 0 32 read-only 4 0x4 0,1,2,3 COMPID%s Component ID Register 0xFF0 32 read-only 0 0 COMPID Component ID 0 32 read-only MTBDWT MTB data watchpoint and trace MTBDWT_ 0xF0001000 0 0x1000 registers CTRL MTB DWT Control Register 0 32 read-only 0x2F000000 0xFFFFFFFF DWTCFGCTRL DWT configuration controls 0 28 read-only NUMCMP Number of comparators 28 4 read-only 2 0x10 0,1 COMP%s MTB_DWT Comparator Register 0x20 32 read-write 0 0xFFFFFFFF COMP Reference value for comparison 0 32 read-write 2 0x10 0,1 MASK%s MTB_DWT Comparator Mask Register 0x24 32 read-write 0 0xFFFFFFFF MASK MASK 0 5 read-write FCT0 MTB_DWT Comparator Function Register 0 0x28 32 read-write 0 0xFFFFFFFF FUNCTION Function 0 4 read-write 0000 Disabled. #0000 0100 Instruction fetch. #0100 0101 Data operand read. #0101 0110 Data operand write. #0110 0111 Data operand (read + write). #0111 DATAVMATCH Data Value Match 8 1 read-write 0 Perform address comparison. #0 1 Perform data value comparison. #1 DATAVSIZE Data Value Size 10 2 read-write 00 Byte. #00 01 Halfword. #01 10 Word. #10 11 Reserved. Any attempts to use this value results in UNPREDICTABLE behavior. #11 DATAVADDR0 Data Value Address 0 12 4 read-write MATCHED Comparator match 24 1 read-only 0 No match. #0 1 Match occurred. #1 FCT1 MTB_DWT Comparator Function Register 1 0x38 32 read-write 0 0xFFFFFFFF FUNCTION Function 0 4 read-write 0000 Disabled. #0000 0100 Instruction fetch. #0100 0101 Data operand read. #0101 0110 Data operand write. #0110 0111 Data operand (read + write). #0111 MATCHED Comparator match 24 1 read-only 0 No match. #0 1 Match occurred. #1 TBCTRL MTB_DWT Trace Buffer Control Register 0x200 32 read-write 0x20000000 0xFFFFFFFF ACOMP0 Action based on Comparator 0 match 0 1 read-write 0 Trigger TSTOP based on the assertion of MTBDWT_FCT0[MATCHED]. #0 1 Trigger TSTART based on the assertion of MTBDWT_FCT0[MATCHED]. #1 ACOMP1 Action based on Comparator 1 match 1 1 read-write 0 Trigger TSTOP based on the assertion of MTBDWT_FCT1[MATCHED]. #0 1 Trigger TSTART based on the assertion of MTBDWT_FCT1[MATCHED]. #1 NUMCOMP Number of Comparators 28 4 read-only DEVICECFG Device Configuration Register 0xFC8 32 read-only 0 0xFFFFFFFF DEVICECFG DEVICECFG 0 32 read-only DEVICETYPID Device Type Identifier Register 0xFCC 32 read-only 0x4 0xFFFFFFFF DEVICETYPID DEVICETYPID 0 32 read-only 8 0x4 4,5,6,7,0,1,2,3 PERIPHID%s Peripheral ID Register 0xFD0 32 read-only 0 0 PERIPHID PERIPHID 0 32 read-only 4 0x4 0,1,2,3 COMPID%s Component ID Register 0xFF0 32 read-only 0 0 COMPID Component ID 0 32 read-only ROM System ROM ROM_ 0xF0002000 0 0x1000 registers 3 0x4 0,1,2 ENTRY%s Entry 0 32 read-only 0 0 ENTRY ENTRY 0 32 read-only TABLEMARK End of Table Marker Register 0xC 32 read-only 0 0xFFFFFFFF MARK MARK 0 32 read-only SYSACCESS System Access Register 0xFCC 32 read-only 0x1 0xFFFFFFFF SYSACCESS SYSACCESS 0 32 read-only 8 0x4 4,5,6,7,0,1,2,3 PERIPHID%s Peripheral ID Register 0xFD0 32 read-only 0 0 PERIPHID PERIPHID 0 32 read-only 4 0x4 0,1,2,3 COMPID%s Component ID Register 0xFF0 32 read-only 0 0 COMPID Component ID 0 32 read-only MCM Core Platform Miscellaneous Control Module MCM_ 0xF0003000 0x8 0x7C registers PLASC Crossbar Switch (AXBS) Slave Configuration 0x8 16 read-only 0x7 0xFFFF ASC Each bit in the ASC field indicates whether there is a corresponding connection to the crossbar switch's slave input port. 0 8 read-only 0 A bus slave connection to AXBS input port n is absent. #0 1 A bus slave connection to AXBS input port n is present. #1 PLAMC Crossbar Switch (AXBS) Master Configuration 0xA 16 read-only 0x5 0xFFFF AMC Each bit in the AMC field indicates whether there is a corresponding connection to the AXBS master input port. 0 8 read-only 0 A bus master connection to AXBS input port n is absent #0 1 A bus master connection to AXBS input port n is present #1 PLACR Platform Control Register 0xC 32 read-write 0x250 0xFFFFFFFF ARB Arbitration select 9 1 read-write 0 Fixed-priority arbitration for the crossbar masters #0 1 Round-robin arbitration for the crossbar masters #1 CFCC Clear Flash Controller Cache 10 1 write-only DFCDA Disable Flash Controller Data Caching 11 1 read-write 0 Enable flash controller data caching #0 1 Disable flash controller data caching. #1 DFCIC Disable Flash Controller Instruction Caching 12 1 read-write 0 Enable flash controller instruction caching. #0 1 Disable flash controller instruction caching. #1 DFCC Disable Flash Controller Cache 13 1 read-write 0 Enable flash controller cache. #0 1 Disable flash controller cache. #1 EFDS Enable Flash Data Speculation 14 1 read-write 0 Disable flash data speculation. #0 1 Enable flash data speculation. #1 DFCS Disable Flash Controller Speculation 15 1 read-write 0 Enable flash controller speculation. #0 1 Disable flash controller speculation. #1 ESFC Enable Stalling Flash Controller 16 1 read-write 0 Disable stalling flash controller when flash is busy. #0 1 Enable stalling flash controller when flash is busy. #1 PID Process ID register 0x30 32 read-write 0 0xFFFFFFFF PID M0_PID For MPU 0 8 read-write 0 Reserved for privileged secure tasks #0 CPO Compute Operation Control Register 0x40 32 read-write 0 0xFFFFFFFF CPOREQ Compute Operation Request 0 1 read-write 0 Request is cleared. #0 1 Request Compute Operation. #1 CPOACK Compute Operation Acknowledge 1 1 read-only 0 Compute operation entry has not completed or compute operation exit has completed. #0 1 Compute operation entry has completed or compute operation exit has not completed. #1 CPOWOI Compute Operation Wake-up on Interrupt 2 1 read-write 0 No effect. #0 1 When set, the CPOREQ is cleared on any interrupt or exception vector fetch. #1 MATCR Master Attribute Configuration Register 0x80 32 read-write 0 0xFFFFFFFF ATC0 Attribute Configuration Master n 0 3 read-write 00x Master attributes are statically forced to {privileged, secure}. #00x 010 Master attributes are statically forced to {user, secure}. #010 011 Master attributes are statically forced to {user, nonsecure}. #011 100 Enable master attribute {privileged or user} and statically force {secure}. #100 101 Enable master attribute {privileged or user} and statically force {nonsecure}. #101 11x Enable master attribute {privileged or user, secure or nonsecure} #11x RO0 Read-Only Master n 7 1 read-write 0 Writes to the ATCn are allowed. #0 1 Writes to the ATCn are ignored. #1 ATC2 Attribute Configuration Master n 16 3 read-write 00x Master attributes are statically forced to {privileged, secure}. #00x 010 Master attributes are statically forced to {user, secure}. #010 011 Master attributes are statically forced to {user, nonsecure}. #011 100 Enable master attribute {privileged or user} and statically force {secure}. #100 101 Enable master attribute {privileged or user} and statically force {nonsecure}. #101 11x Enable master attribute {privileged or user, secure or nonsecure} #11x RO2 Read-Only Master n 23 1 read-write 0 Writes to the ATCn are allowed. #0 1 Writes to the ATCn are ignored. #1 MMDVSQ Divide and Square Root MMDVSQ_ 0xF0004000 0 0x14 registers DEND Dividend Register 0 32 read-write 0 0 DIVIDEND Dividend 0 32 read-write DSOR Divisor Register 0x4 32 read-write 0 0 DIVISOR Divisor 0 32 read-write CSR Control/Status Register 0x8 32 read-write 0 0x9FFFFFFF SRT Start 0 1 write-only 0 No operation initiated #0 1 If CSR[DFS] = 1, then initiate a divide calculation, else ignore #1 USGN Unsigned calculation 1 1 read-write 0 Perform a signed divide #0 1 Perform an unsigned divide #1 REM REMainder calculation 2 1 read-write 0 Return the quotient in the RES for the divide calculation #0 1 Return the remainder in the RES for the divide calculation #1 DZE Divide-by-Zero-Enable 3 1 read-write 0 Reads of the RES register return the register contents #0 1 If CSR[DZ] = 1, an attempted read of RES register is error terminated to signal a divide-by-zero, else the register contents are returned #1 DZ Divide-by-Zero 4 1 read-only 0 The last divide operation had a non-zero divisor, that is, DSOR != 0 #0 1 The last divide operation had a zero divisor, that is, DSOR = 0 #1 DFS Disable Fast Start 5 1 read-write 0 A divide operation is initiated by a write to the DSOR register #0 1 A divide operation is initiated by a write to the CSR register with CSR[SRT] = 1 #1 SQRT SQUARE ROOT 29 1 read-only 0 Current or last MMDVSQ operation was not a square root #0 1 Current or last MMDVSQ operation was a square root #1 DIV DIVIDE 30 1 read-only 0 Current or last MMDVSQ operation was not a divide #0 1 Current or last MMDVSQ operation was a divide #1 BUSY BUSY 31 1 read-only 0 MMDVSQ is idle #0 1 MMDVSQ is busy performing a divide or square root calculation #1 RES Result Register 0xC 32 read-write 0 0 RESULT Result 0 32 read-write RCND Radicand Register 0x10 32 read-write 0 0 RADICAND Radicand 0 32 read-write